液-液-液微萃取-高效液相色谱法测定人尿液中的美沙酮

建立了液-液-液微萃取与高效液相色谱联用技术快速分析尿样中美沙酮的方法.对有机溶剂种类、体积、样品溶液的pH值、萃取时间、搅拌速度进行了优化.方法的线性范围为0.05～10 mg/L,检出限为0.025 mg/L,相对标准偏差小于5%.     

Carrier-mediated liquid phase microextraction coupled with high performance liquid chromatography for determination of illicit drugs in human urine

A new method was developed for the analysis of illicit drugs in human urine by coupling carrier-mediated liquid phase microextraction (LPME) to high performance liquid chromatography (HPLC). By adding an appropriate carrier in organic phase, simultaneous extraction and enrichment of hydrophilic (morphine and ephedrine) and hydrophobic (pethidine) drugs were achieved. Effects of the types of organic solvents and carriers, the carrier concentration in the organic phase, the HCl concentration in the acceptor solution, the stirring rate, and the extraction time on the enrichment factor of analytes were investigated. Under the optimal experimental conditions, high enrichment factors (202-515) were obtained. The linear detection ranges were 0.1-10 mg L⁻¹ for the studied drugs. The limits of detection (LOD) at signal-to-noise ratio of 3 were 0.05 mg L⁻¹ for both morphine and ephedrine, and 0.02 mg L⁻¹ for pethidine. This method was successfully applied to analysis of ephedrine in real urine specimens, revealing that the determination of illicit drugs in urine was feasible.     

液相微萃取-高效液相色谱法分析葡萄汁中多酚类化合物

建立了一种基于液相微萃取与高效液相色谱联用技术测定葡萄汁中鞣花酸、白藜芦醇和槲皮素的分析方法. 比较了单液滴液相微萃取和中空纤维液相微萃取两种萃取模式, 选择了单液滴液相微萃取作为3种多酚类化合物的液相微萃取模式. 考察了搅拌速度、萃取时间、料液相pH和料液相离子强度的影响. 鞣花酸、白藜芦醇和槲皮素的富集倍数分别为48.4、 79.4和155.8, 方法的线性范围为0.0050～5.0 μg/mL, 鞣花酸、白藜芦醇和槲皮素的检出限分别为0.015, 0.0020, 0.0080 μg/mL, 相对标准偏差分别为2.0%, 1.8%和1.7%. 用于实际样品葡萄汁的分析, 加标回收率在81.9%～102.3%之间.     

中空纤维三相液相微萃取-高效液相色谱法测定环境水样中7种苯氧羧酸类除草剂

建立了利用中空纤维三相液相微萃取-高效液相色谱联用技术(HF-LPME-HPLC)同时测定环境水中痕量麦草畏(dicamba)、氟草烟(fluroxypyr)、4-氯苯氧乙酸(4-CPA)、2甲4氯(MCPA)、2,4-滴(2,4-D)、2,4-滴苯氧丁酸(2,4-DB)和2甲4氯苯氧丁酸(MCPB)等7种苯氧羧酸类除草剂的分析方法。考察了萃取剂﹑接受相和给出相pH值、萃取时间﹑搅拌速度和盐效应等对检测的影响,通过正交试验优化萃取条件,得到的最佳萃取条件为正辛醇作萃取剂,给出相pH为3,接受相pH为12,萃取30 min,搅拌速度400 r/min。结果表明7种除草剂在较宽的线性范围内线性良好,相关系数为0.9953～0.9988,检出限(信噪比为3)为0.2～1.0 μg/L,富集倍数为76.7～121,加标回收率为68%～104%,相对标准偏差为3.2%～8.1%。该法灵敏度高、操作简单、检测快速、有机溶剂消耗少,为环境水样中痕量苯氧羧酸类除草剂残留的分析提供了有益的参考。     

中空纤维三相液相微萃取-高效液相色谱法测定水中的4种酚类化合物

建立了中空纤维液-液-液三相微萃取-高效液相色谱法测定水中4种酚类化合物的方法.实验系统地优化了影响萃取效率的因素(包括有机溶剂种类、接收相浓度、分散相pH值、加盐量、转速及萃取时间).得到的最佳萃取条件为:萃取剂为正辛醇,接收相NaOH溶液的浓度为0.09 mol/L,分散相的pH为4,萃取时间为40 min,搅拌速...     

Enrichment and sensitive determination of dichlorodiphenyltrichloroethane and its metabolites with temperature controlled ionic liquid dispersive liquid phase microextraction prior to high performance liquid phase chromatography

Dichlorodiphenyltrichloroethane (DDT) and its main metabolites are important environmental pollutants and have been in the focusing center. It is of great value to develop simple, rapid, sensitive and easy to operate method for monitoring them. Present work established a novel temperature controlled ionic liquid dispersive liquid phase microextraction method in combination with high performance liquid chromatography for the enrichment and determination of DDT and its metabolites. Proposed method used only ionic liquid 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) for the enrichment and overcame the demerits of conventional single drop liquid phase microextraction and dispersive liquid-liquid microextraction. Temperature has two functions here, one is to promote the dispersing of ionic liquid into the solution and forming infinitesimal micro-drop and increasing the chance of the analytes extracted into ionic liquid phase, and the other one is to perform phase-separation. A series of factors that would affect the extraction performance was systematically investigated and optimized. The experimental results indicated that the detection limits obtained for p,p′-DDD, p,p′-DDT, o,p′-DDT and p,p′-DDE were 0.24, 0.24, 0.45, 0.24 ng mL⁻¹, respectively. The linear ranges for them were from 1.0 to 100 ng mL⁻¹, and the precisions were between 3.8% and 6.7% (n = 6). The proposed method was validated with four real-world samples and excellent results were achieved.     

Flow injection on-line dialysis coupled to high performance liquid chromatography for the determination of some organic acids in wine

A combined system of flow injection on-line dialysis sample pretreatment and high performance liquid chromatographic separation/detection (FID-HPLC) was developed for simultaneous determination of six organic acids (tartaric, malic, lactic, acetic, citric and succinic acids). A sample or mixed standard solution (400 μL) was injected into a donor stream (water) of FID system and was pushed further through a dialysis cell, while an acceptor solution (water) was held in the opposite side of the dialysis membrane. The dialysate containing organic acids in the acceptor solution was then flowed to an injection loop of the HPLC valve, where it was further injected into the HPLC system and analysed under normal HPLC conditions, using a reversed-phase (C₁₈) analytical column and UV detection (210 nm). The order of elution was tartaric, malic, lactic, acetic, citric and succinic acids with the analysis time of 8 min. The FID system could be operated in parallel with HPLC separation, providing sample throughput of 7.5 h⁻¹. Dialysis efficiencies of six organic acids were in range of 4.6-9.5%. Calibration graphs for all the mentioned organic acids were linear over the range of 250-7500 mg L⁻¹. Precisions for all the organic acids were within 5.4%. The proposed system was successfully applied for analysis of some Thai wines. By spiking wine samples with mixed acid standard solutions, the percentage recoveries in range of 84-104 were found. This system has advantages of fast and high degrees of automation for dialysis sample pretreatment, on-line sample separation and dilution, good clean-up for prolongation of life-time of the HPLC column and low consumption of chemicals and materials.     

Determination of endocrine-disrupting compounds in water by carbon nanotubes solid-phase microextraction fiber coupled online with high performance liquid chromatography

The commercial solid phase microextraction (SPME) fibers are not stable enough in organic solvent and tend to swell and strip off from the silica fiber in the high performance liquid chromatography (HPLC) mobile phase, and therefore the application of SPME coupled online with HPLC is limited. In this study, an SPME fiber coated with single walled carbon nanotubes (SWCNTs), prepared by means of electrophoretic deposition, was coupled on line to HPLC for the determination of four endocrine-disrupting compounds, i.e. bisphenol A (BPA), estrone (E₁), 17α-ethynylestradiol (EE₂) and octylphenol (OP), in aqueous samples. The results showed that the SWCNTs coating on the prepared fiber did not swell and strip off from the platinum fiber throughout the experiment, thus indicating a high resistance to the HPLC mobile phase, the mixture of water and acetonitrile. The SWCNTs fiber had similar (for OP) or higher (for BPA, EE₂ and E₁) extraction efficiencies than the commonly used polyacrylate fiber, and had a lifetime of more than 120 operation times. Under the optimized conditions, the linearity of the proposed method was 1.0-30.0 μg/L for BPA and OP and 3.0-90.0 μg/L for E₁ and EE₂. The limits of detection (LODs; S/N = 3) and limits of quantification (LOQs; S/N = 10) of the method were 0.32-0.52 μg/L and 1.06-1.72 μg/L, respectively. Repeatability for one fiber (n = 3) was in the range of 1.3-7.1% and fiber-to-fiber reproducibility (n = 3) was in the range of 1.6-8.4%. The proposed method was successfully applied for the analysis of spiked tap water and seawater samples with recoveries from 81.8 to 97.3%.     

Optimization of temperature-controlled ionic liquid dispersive liquid phase microextraction combined with high performance liquid chromatography for analysis of chlorobenzenes in water samples

Temperature-controlled ionic liquid dispersive liquid phase microextraction (TCIL-DLPME) combined with high performance liquid chromatography-diode array detection (HPLC-DAD) was applied for preconcentration and determination of chlorobenzenes in well water samples. The proposed method used 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄mim][PF₆]) as the extraction solvent. The effect of different variables on extraction efficiency was studied simultaneously using an experimental design. The variables of interest in the TCIL-DLPME were extraction solvent volume, salt effect, solution temperature, extraction time, centrifugation time, and heating time. The Plackett-Burman design was employed for screening to determine the variables significantly affecting the extraction efficiency. Then, the significant factors were optimized by using a central composite design (CCD) and the response surface equations were developed. The optimal experimental conditions obtained from this statistical evaluation included: extraction solvent volume, 75 μL; extraction time, 20 min; centrifugation time, 25 min; heating time, 4 min; solution temperature, 50 °C; and no addition of salt. Under optimal conditions, the preconcentration factors were between 187 and 298. The limit of detections (LODs) ranged from 0.05 μg L⁻¹ (for 1,2-dichlorobenzene) to 0.1 μg L⁻¹ (for 1,2,3-trichlorobenzene). Linear dynamic ranges (LDRs) of 0.5-300 and 0.5-500 μg L⁻¹ were obtained for dichloro- and trichlorobenzenes, respectively. The performance of the method was evaluated for extraction and determination of chlorobenzenes in well water samples in micrograms per liter and satisfactory results were obtained (RSDs < 9.2%).     

固相微萃取-高效液相色谱联用测定环境水样中双酚A的自由溶解态浓度

应用可忽略耗损固相微萃取与高效液相色谱联用技术测定了环境水样中双酚A的自由溶解态浓度。为了获得高的灵敏度并减小环境因素（如温度和搅拌等）的影响,采用商品化固相微萃取纤维CW／TPR进行平衡采样。在环境水样常见pH（5～8）、缓冲容量（5～200mmol／L）和盐度（0～500mmol／L）条件下,4h可以达到萃取平衡。100mL样品足以避免样品耗损。以配制在250mmol／L NaCl和125mmol／L磷酸盐溶液（pH6．4）中的双酚A标准溶液进行校准,可以将缓冲液（0～200mmol／L）、盐度（0～500mmol／L）和pH（5．7～8．5）的影响控制在15％偏差范围以内。如需更准确的测定,也可以对样品pH值的影响加以校正。pH为6．4时,方法的线性范围为0．1～250μg／L,检出限为0．03μg／L,相对标准偏差（5μg/L,n=3）为1．1％。采用本方法测定了污水处理厂排水口的双酚A的自由溶解态浓度。     

Simultaneous determination of some food additives in soft drinks and other liquid foods by flow injection on-line dialysis coupled to high performance liquid chromatography

Flow injection on-line dialysis was developed for sample pretreatment prior to the simultaneous determination of some food additives by high performance liquid chromatography (FID-HPLC). A liquid sample or mixed standard solution (900 μL) was injected into a donor stream (5%, w/v, sucrose) of FID system and was pushed further through a dialysis cell, while an acceptor solution (0.025 mol L⁻¹ phosphate buffer, pH 3.75) was held in the opposite side of the dialysis membrane. The dialysate was then flowed to an injection loop of the HPLC valve, where it was further injected into the HPLC system and analyzed under isocratic reverse-phase HPLC conditions and UV detection (230 nm). The order of elution of five food additives was acesulfame-K, saccharin, caffeine, benzoic acid and sorbic acid, respectively, with the analysis time of 14 min. On-line dialysis and HPLC analysis could be performed in parallel, providing sample throughput of 4.3 h⁻¹. Dialysis efficiencies of five food additives were in ranges of 5-11%. Linear calibration graphs were in ranges of 10-100 mg L⁻¹ for acesulfame-K and saccharin, 10-250 mg L⁻¹ for benzoic acid and 10-500 mg L⁻¹ for caffeine and sorbic acid. Good precisions (RSD < 5%) for all the additives were obtained. The proposed system was applied to soft drink and other liquid food samples. Acceptable percentage recoveries could be obtained by appropriate dilution of the sample before injecting into the system. The developed system has advantages of high degrees of automation for sample pretreatment, i.e., on-line sample separation and dilution and low consumption of chemicals and materials.     

Application of liquid-phase microextraction for the determination of phoxim in water samples by high performance liquid chromatography with diode array detector

A new method, which involves liquid-phase microextraction (LPME) followed by high performance liquid chromatography (HPLC) with diode array detector (DAD), was developed to determine phoxim in water sample. Experimental parameters affecting the extraction efficiency, such as extraction solvent, solvent volume, agitation speed of the sample and extraction time were investigated. Under the optimal extraction conditions, phoxim was found to yield a good linear calibration curve in the concentration range from 0.01 to 5 μg mL⁻¹. The limit of detection (LOD) is 10 ng mL⁻¹, and relative standard deviation (RSD) at the 100 ng mL⁻¹ levels is 8.4%. Lake water and tap water samples were successfully analyzed using the proposed method.     

Determination of three estrogens and bisphenol A by functional ionic liquid dispersive liquid‐phase microextraction coupled with ultra‐high performance liquid chromatography and ultraviolet detection

A hydroxyl‐functionalized ionic liquid, 1‐hydroxyethyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)imide, was employed in an improved dispersive liquid‐phase microextraction method coupled with ultra high performance liquid chromatography for the enrichment and determination of three estrogens and bisphenol A in environmental water samples. The introduced hydroxyl group acted as the H‐bond acceptor that dispersed the ionic liquid effectively in the aqueous phase without dispersive solvent or external force. Fourier transform infrared spectroscopy indicated that the hydroxyl group of the cation of the ionic liquid enhanced the combination of extractant and analytes through the formation of hydrogen bonds. The improvement of the extraction efficiency compared with that with the use of alkyl ionic liquid was proved by a comparison study. The main parameters including volume of extractant, temperature, pH, and extraction time were investigated. The calibration curves were linear in the range of 5.0–1000 μg/L for estrone, estradiol, and bisphenol A, and 10.0–1000 μg/L for estriol. The detection limits were in the range of 1.7–3.4 μg/L. The extraction efficiency was evaluated by enrichment factor that were between 85 and 129. The proposed method was proved to be simple, low cost, and environmentally friendly for the determination of the four endocrine disruptors in environmental water samples.     

Supramolecular-based solvent microextraction of carbaryl in water samples followed by high performance liquid chromatography determination

In this study, a simple, rapid, low cost, sensitive and environmentally friendly technique, supramolecular solvent microextraction (SM-SME) followed by high performance liquid chromatography-ultraviolet has been proposed to extract carbaryl from water samples. Parameters, affecting the SM-SME performance such as the weight of decanoic acid (DeA), volume of tetrahydrofuran (THF), pH and salt concentration, were studied and optimised. The effect of the pH on the extraction efficiency was evaluated by one–factor-at-a-time methodology, but the other variables were optimised by a face-centred cube central composite design methodology. Optimum extraction conditions were obtained: DeA: 70 mg; THF: 650 µL; salt concentration: 10% (w/v) NaCl and pH = 2–4), and the performance of the proposed method was evaluated. Under the optimum conditions, good linearity (1.0–500 µg L^?1, r² = 0.9994) was obtained. Limit of detection and limit of quantification were 0.3–1.0 µg L^?1, respectively. Also, the recoveries of the carbaryl were obtained in the ranged from 96% to 105%. Finally, proposed method was successfully applied for the determination of the carbaryl in the water samples of farms run-off and rivers and satisfactory results were obtained.     

Matrix solid‐phase dispersion coupled with homogeneous ionic liquid microextraction for the determination of sulfonamides in animal tissues using high‐performance liquid chromatography

Matrix solid‐phase dispersion coupled with homogeneous ionic liquid microextraction was developed and applied to the extraction of some sulfonamides, including sulfamerazine, sulfamethazine, sulfathiazole, sulfachloropyridazine, sulfadoxine, sulfisoxazole, and sulfaphenazole, in animal tissues. High‐performance liquid chromatography was applied to the separation and determination of the target analytes. The solid sample was directly treated by matrix solid‐phase dispersion and the eluate obtained was treated by homogeneous ionic liquid microextraction. The ionic liquid was used as the extraction solvent in this method, which may result in the improvement of the recoveries of the target analytes. To avoid using organic solvent and reduce environmental pollution, water was used as the elution solvent of matrix solid‐phase dispersion. The effects of the experimental parameters on recoveries, including the type and volume of ionic liquid, type of dispersant, ratio of sample to dispersant, pH value of elution solvent, volume of elution solvent, amount of salt in eluate, amount of ion‐pairing agent (NH₄PF₆), and centrifuging time, were evaluated. When the present method was applied to the analysis of animal tissues, the recoveries of the analytes ranged from 85.4 to 118.0%, and the relative standard deviations were lower than 9.30%. The detection limits for the analytes were 4.3–13.4 μg/kg.     

Combination of ionic liquid dispersive liquid-phase microextraction and high performance liquid chromatography for the determination of triazine herbicides in water samples

A temperature-controlled ionic liquid dispersive liquid-phase microextraction in combination with high performance liquid chromatography was developed for the enrichment and determination of triazine herbicides such as cyanazine,simazine,and atrazine in water samples.1-Octyl-3-methylimidazolium hexafluorophosphate([C8MIM][PF6]) was selected as the extraction solvent.Several experimental parameters were optimized.Under the optimal conditions,the linear range for cyanazine was in the concentration range of 0.5–80 mg/L and the linear range for simazine and atrazine was in the range of1.0–100 mg/L.The limit of detection(LOD,S/N = 3) was in the ranges of 0.05–0.06 mg/L,and the intra day and inter day precision(RSDs,n = 6) was in the ranges of 3.2%–6.6% and 4.8%–8.9%,respectively.Four real water samples were analyzed with the developed method,and the experimental results showed that the spiked recoveries were satisfactory.All these exhibited that the developed method was a valuable tool for monitoring such pollutants.     

整体柱在线固相微萃取-高效液相色谱法分析爽肤水中痕量雌激素

以甲基丙烯酸缩水甘油酯(GMA)为功能单体、乙二醇二甲基丙烯酸酯(EDMA)为交联剂,偶氮二异丁腈(AIBN)为引发剂、甲醇及正己烷(14∶5,v/v)为二元致孔剂,通过原位聚合反应制备了聚甲基丙烯酸缩水甘油酯(Poly(GMA-co-EDMA))毛细管整体柱。研究表明,制备的Poly(GMA-co-EDMA)整体柱具有良好的通透性和较低的柱压(1.5×106Pa,冲洗流速0.5 mL/min)。该整体柱对雌二醇、炔雌醇、雌酮和己烯雌酚的富集倍数分别为86、116、77和86。构建了整体柱在线微萃取接口装置,建立了整体柱在线固相微萃取-高效液相色谱(HPLC)测定爽肤水中痕量雌二醇、炔雌醇、雌酮和己烯雌酚的分析方法。该分析方法的检出限(S/N=3)为0.05~0.20μg/L。将方法应用于爽肤水中雌激素的检测,加标回收率为69.3%~111.3%,RSD5.0%。所建立的方法简单、快速、灵敏、准确,可满足爽肤水中痕量雌激素的分析。     

微波辅助-顶空液相微萃取在线联用-高效液相色谱法测定环境水样中的敌敌畏

基于微波辅助-顶空液相微萃取联用(MAE-HS-LPME)这一样品前处理方法,采用高效液相色谱法(HPLC)对水样中的敌敌畏残留量进行了测定。对影响萃取的因素如萃取剂、微波辐射功率、萃取时间、离子强度和样品基质的pH值等进行了考察。萃取条件为: 选用二甲苯作萃取剂,萃取时间为15 min,微波辐射功率300 W,NaCl含量为5%,pH为2.5。在最佳条件下,敌敌畏的检出限(信噪比为3时)为0.96 μg/L,定量限(信噪比为10时)为3.20 μg/L,萃取富集倍数为54,实际水样的加标回收率为87.4%～103%。与传统的前处理方法相比,本方法具有简便、快速、高效、节省溶剂、选择性好、应用范围广的特点。     

Ionic liquid foam floatation coupled with ionic liquid dispersive liquid–liquid microextraction for the separation and determination of estrogens in water samples by high‐performance liquid chromatography with fluorescence detection

An ionic liquid foam floatation coupled with ionic liquid dispersive liquid–liquid microextraction method was proposed for the extraction and concentration of 17‐α‐estradiol, 17‐β‐estradiol‐benzoate, and quinestrol in environmental water samples by high‐performance liquid chromatography with fluorescence detection. 1‐Hexyl‐3‐methylimidazolium tetrafluoroborate was applied as foaming agent in the foam flotation process and dispersive solvent in microextraction. The introduction of the ion‐pairing and salting‐out agent NH₄PF₆ was beneficial to the improvement of recoveries for the hydrophobic ionic liquid phase and analytes. Parameters of the proposed method including concentration of 1‐hexyl‐3‐methylimidazolium tetrafluoroborate, flow rate of carrier gas, floatation time, types and concentration of ionic liquids, salt concentration in samples, extraction time, and centrifugation time were evaluated. The recoveries were between 98 and 105% with relative standard deviations lower than 7% for lake water and well water samples. The isolation of the target compounds from the water was found to be efficient, and the enrichment factors ranged from 4445 to 4632. This developing method is free of volatile organic solvents compared with regular extraction. Based on the unique properties of ionic liquids, the application of foam floatation, and dispersive liquid–liquid microextraction was widened.     

Ultrasound-assisted surfactant-enhanced emulsification microextraction for the determination of carbamate pesticides in water samples by high performance liquid chromatography

A novel ultrasound-assisted surfactant-enhanced emulsification microextraction (UASEME) coupled with high performance liquid chromatography-diode array detection has been developed for the extraction and determination of six carbamate pesticides (metolcarb, carbofuran, carbaryl, pirimicarb, isoprocarb and diethofencarb) in water samples. In the UASEME technique, Tween 20 was used as emulsifier, and chlorobenzene and chloroform were used as dual extraction solvent without using any organic dispersive solvent that is normally required in the previously described common dispersive liquid–liquid microextraction method. Parameters that affect the extraction efficiency, such as the kind and volume of the extraction solvent, the type and concentration of the surfactant, ultrasound emulsification time and salt addition, were investigated and optimized for the method. Under the optimum conditions, the enrichment factors were in the range between 170 and 246. The limits of detection of the method were 0.1–0.3 ng mL⁻¹ and the limits of quantification were between 0.3 and 0.9 ng mL⁻¹, depending on the compounds. The linearity of the method was obtained in the range of 0.3–200 ng mL⁻¹ for metolcarb, carbaryl, pirimicarb, and diethofencarb, 0.6–200 ng mL⁻¹ for carbofuran, and 0.9–200 ng mL⁻¹ for isoprocarb, with the correlation coefficients (r) ranging from 0.9982 to 0.9998. The relative standard deviations varied from 3.2 to 4.8% (n = 5). The recoveries of the method for the six carbamates from water samples at spiking levels of 1.0, 10.0, 50.0 and 100.0 ng mL⁻¹ were ranged from 81.0 to 97.5%. The proposed UASEME technique has demonstrated to be simple, practical and environmentally friendly for the determination of carbamates residues in river, reservoir and well water samples.