Electropolymerized surface ion imprinting films on a gold nanoparticles/single-wall carbon nanotube nanohybrids modified glassy carbon electrode for electrochemical detection of trace mercury(II) in water

Electrochemical detection of Hg(II) using a electropolymerized ion imprinting poly(2-mercaptobenzothiazole) films at the surface of gold nanoparticles/single-walled carbon nanotube nanohybrids modified glassy carbon electrode (PMBT/AuNPs/SWCNTs/GCE) is described for the first time. The Hg(II)-imprinted PMBT/AuNPs/SWCNTs/GCE sensor exhibits larger binding to functionalized capacity, larger affinity, faster binding kinetics and higher selectivity to template Hg(II). The differential pulse anodic stripping voltammetry (DPASV) response of the Hg(II)-imprinted PMBT/AuNPs/SWCNTs/GCE sensor to Hg(II) is ca. 3.7- and 10.5-fold higher than that at the non-imprinted PMBT/AuNPs/SWCNTs/GCE and the imprinted PMBT/AuNPs/GCE, respectively, and the detection limit for Hg(II) is 0.08 nM (S/N = 3, which is well below the guideline value given by the World Health Organization) and a sensitivity of 0.749 μA nM⁻¹ was obtained. Excellent wide linear range (0.4–96.0 nM) and good repeatability (relative standard deviation of 2.6%) were obtained for Hg(II). The interference experiments show that Ag(I), Pb(II), Cd(II), Zn(II) and Cu(II) had little or no influence on the Hg(II) signal. These values, particularly the high sensitivity and excellent selectivity in contrast to the values reported previously in the area of electrochemical Hg(II) detection, demonstrate the analytical performance of the Hg(II)-imprinted PMBT/AuNPs/SWCNTs/GCE toward Hg(II) is superior to the existing electrodes and could be used for efficient determination of Hg(II) in natural water samples.     

A novel poly(3,4-ethylenedioxythiophene)/iron phthalocyanine/multi-wall carbon nanotubes nanocomposite with high electrocatalytic activity for nitrite oxidation

In the present work, the oxidative electrochemistry of nitrite on the poly(3,4-ethylenedioxythiophene)/iron phthalocyanine/multi-wall carbon nanotubes-(PEDOT/FePc/MWCNT) modified screen-printed carbon electrodes (SPCE) has been investigated. The parameters, such as overpotential, current density and rate constant at PEDOT/FePc/MWCNT-modified SPCE, were compared with an un-modified, FePc-, and FePc/MWCNT-modified SPCE for electro-oxidation of nitrite. As compared with the un-modified SPCE, an increase in the anodic peak current density (J_pa) (∼100%) along with a decrease in the anodic peak potential (E_pa) of ∼150 mV for electro-oxidation of nitrite at the FePc-modified SPCE was observed. When an under-layer of MWCNT was introduced onto FePc-modified SPCE, denoted as FePc/MWCNT-modified SPCE, and the number of FePc/MWCNT bilayer was optimized, the heterogeneous electron transfer rate constant (k) at FePc/MWCNT-modified SPCE was enhanced about 7.8 times as compared with that at FePc-modified SPCE. Moreover, as a layer of PEDOT film was electrodeposited onto the FePc/MWCNT-modified SPCE, denoted as PEDOT/FePc/MWCNT-modified SPCE, a significant increase in current response along with a remarkable decrease in E_pa were noticed. This can be attributed to the pre-concentration effect induced by the electrostatic interaction between the negatively charged nitrite and oxidized PEDOT film. On the whole, the PEDOT/FePc/MWCNT-modified SPCE greatly reduces the overpotential of ∼330 mV along with 3.5 times enhanced the peak current density for the electro-oxidation of nitrite as compared with un-modified SPCE. The sensitivity and limit of detection (S/N = 3) for the PEDOT/FePc/MWCNT-modified SPCE were found to be as 638 mA cm⁻² M⁻¹ and 71 nM, respectively. Notably, PEDOT/FePc/MWCNT-modified SPCE has a lower sensing potential than compared to several other modified electrodes. The developed sensor was also applied for the determination of nitrite in tap water sample.     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

羟胺在碳纳米管修饰玻碳电极上的电催化还原及电化学动力学性质研究

研究了羟胺在碳纳米管修饰玻碳电极(CNT/GC)上的电化学行为。研究结果表明,碳纳米管对羟胺的电化学行为有良好的电催化作用,在-0.62 V有一还原峰,是羟胺获得2个电子还原为铵所形成,同时测定了该电化学过程的动力学参数:电子转移数n为2,电子转移系数α为0.287,电极反应速率常数k为1.35×10-3cm/s。     

Determination of sulfonamides in milk samples by HPLC with amperometric detection using a glassy carbon electrode modified with multiwalled carbon nanotubes

A sensitive and accurate method for determining five sulfonamides based on HPLC with amperometric detection and using a glassy carbon electrode modified with multiwalled carbon nanotubes is proposed. Optimal conditions for the quantitative separation of selected sulfonamides were studied, and glassy carbon electrodes with and without modification with carbon nanotubes were systematically investigated as electrodic materials. Statistical analysis of the obtained results demonstrated that these modified electrodes achieved considerably better stability and sensitivity than the conventional unmodified ones. Detection limits were in the 1.2–6.0 ng/mL range. The usefulness of the method was demonstrated by the analysis of milk samples, taking into account the European legislation on residues in food products, following both a screening method to classify the samples and a confirmation method to provide more detailed information in the case of positive samples.     

盐酸阿霉素在玻碳电极上的电化学行为研究及分析应用

采用线性扫描伏安法和循环伏安法研究了盐酸阿霉素在玻碳电极上的电化学行为及电极反应机理,优化了测定盐酸阿霉素的各实验参数。结果表明,在0.01 mol/L的HCl溶液中,盐酸阿霉素在-0.40 V处出现(vs.SCE)一灵敏的还原峰,峰电流与其溶液浓度在5.0×10-8~1.0×10-6mol/L(r=0.999)和1.0×10-6~1.0×10-5mol/L(r=0.998)范围内呈良好的线性关系,检出限为1.0×10-8mol/L。并用循环伏安法研究了盐酸阿霉素的峰电流性质,发现电极反应属于准可逆过程,出现一对灵敏的氧化还原峰,体系属准可逆吸附波。利用盐酸阿霉素在玻碳电极的电化学行为建立的分析方法可用于盐酸阿霉素的质量监控及药代动力学研究。     

槲皮素在聚谷氨酸修饰玻碳电极上的伏安行为及检测

制备了聚谷氨酸修饰玻碳电极,通过循环伏安法和差分脉冲伏安法研究了槲皮素在该修饰电极上的电化学行为。在pH 5.00的B-R缓冲液中,槲皮素在修饰电极上于0.28 V(vs Ag/AgCl)电位处产生一个灵敏的DPV阳极氧化峰,氧化峰电流与槲皮素的浓度在1.0×10-8～5×10-5 mol/L的范围内呈良好的线性关系,最低检测限为4.0×10-9 mol/L。实验表明,聚谷氨酸修饰电极可提高槲皮素的检测灵敏度,该电极用于芦丁水解产物中槲皮素的检测,回收率为103.4%～104.5%。     

Electrochemical detection of selenium using glassy carbon electrode modified with reduced graphene oxide

In this work, a simple experimental procedure was reported for the electroanalytical determination of selenium (IV) using reduced graphene oxide (rGO) to modify glassy carbon electrode (GCE). The rGO was obtained by reduction of graphene oxide obtained via Hummer’s method. The synthesised rGO was characterised using X-ray diffraction, Raman spectroscopy, scanning electron microscope (SEM), energy-dispersive spectroscopy and transmission Electron microscopy (TEM). GCE was modified with rGO and the electrochemical properties of the bare and modified electrode were investigated using cyclic voltammetry and electrochemical impedance spectroscopy. The results obtained showed that the modified electrode exhibited more excellent electrochemical properties than the bare GCE. The optimum conditions for detection of selenium in water using square wave anodic stripping voltammetry were as follows: deposition potential ?500 mV, pH 1, pre-concentration time of 240 s and 0.1 M nitric acid was used as supporting electrolyte. The linear regression equation obtained was I (µA) = 0.8432C + 9.2359 and the detection limit was calculated to be 0.85 μg L^?1. However, Cu(II) and Cd(II) are the two cations that interfered in the analysis of selenium in water.

The sensor was also applied for real sample water analysis and the result obtained was affirmed with inductively coupled plasma optical emission spectroscopic method. It is believed that our proposed sensor hold promise for practical application.     

Palladium and the electrochemical quartz crystal microbalance: a new method for the in situ analysis of the precious metal in aqueous solutions

A new method for the quantitative determination of palladium(II) by the electrochemical quartz crystal microbalance (EQCM) technique has been developed. Using a bare carbon-coated quartz crystal, Pd(II) ions are directly deposited from aqueous solution as palladium metal onto the crystal surface, and the Pd(II) concentration is determined with a detection limit of 0.0156 mM, or 1.66 ppm. No complexing agent or preconcentration of palladium is required for the analysis. The palladium is stripped from the crystal through its electrochemical oxidation, regenerating the crystal for subsequent multi-cycle palladium analyses. A conventional gold-coated quartz crystal was incapable of carrying out the same measurements. The EQCM technique presented is simple, sensitive, and reproducible for the detection of this widely used precious metal.     

Sensitive quantification of iodide by ion-exchange chromatography with electrochemical detection at a modified platinum electrode

A rapid and very sensitive method for the accurate determination of free iodide in real samples is described. The method is based on anion-exchange chromatographic separation coupled with amperometric detection at a modified platinum electrode under constant applied potential (+0.85 V vs. Ag AgCl). An experimental setup with an in-line and very effective method of electrode modification is proposed using an amperometric thin-layer cross-flow detector and a flowing solution 300 mg/L of iodide; the working electrode is polarised to the limiting current for oxidation of iodide to iodine in acidic solutions with the consequent formation of an iodine-based film. The results indicated that the modified electrode exhibits high analytical response for iodide electrooxidation with good stability and long-life. The signal intensity of daily experimental sessions (8 h), during which standards and real samples were repeatedly injected, exhibits a moderate lowering (i.e. <6%). Using a mixture of 25 mM HNO₃ and 50 mM NaNO₃ as an eluent phase in ion-exchange chromatography, the detection limit of iodide was estimated to be 0.5 g/L (S/N=3) with an injection volume of 50 L. This method was applied successfully to quantify the iodide content of milk samples and in wastewaters as well as trace amounts in common vegetables and solutions containing high chloride levels.     

Electrochemistry and electrocatalytic activity of catechin film on a glassy carbon electrode toward the oxidation of hydrazine

A very stable electroactive film of catechin was electrochemically deposited on the surface of activated glassy carbon electrode. The electrochemical behavior of catechin modified glassy carbon electrode (CMGCE) was extensively studied using cyclic voltammetry. The properties of the electrodeposited films, during preparation under different conditions, and the stability of the deposited film were examined. The charge transfer coefficient (α) and charge transfer rate constant (k _s) for catechin deposited film were calculated. It was found that the modified electrode exhibited excellent electrocatalytic activity toward hydrazine oxidation and it also showed a very large decrease in the overpotential for the oxidation of hydrazine. The CMGCE was employed to study electrocatalytic oxidation of hydrazine using cyclic voltammetry, rotating disk voltammetry, chronoamperometry, amperometry and square-wave voltammetry as diagnostic techniques. The catalytic rate constant of the modified electrode for the oxidation of hydrazine was determined by cyclic voltammetry, chronoamperometry and rotating disk voltammetry and was found to be around 10⁻³ cm s⁻¹ . In the used different voltammetric methods, the plot of the electrocatalytic current versus hydrazine concentration is constituted of two linear segments with different ranges of hydrazine concentration. Furthermore, amperometry in stirred solution exhibits a detection limit of 0.165 μM and the precision of 4.7% for replicate measurements of 40.0 μM solution of hydrazine.     

苦参碱在多壁碳纳米管修饰玻碳电极上的电催化氧化及其电分析方法

研究了苦参碱(Matrine, MT) 在多壁碳纳米管修饰玻碳电极(MWCNT/GCE)上的电化学行为. 与GCE相比, MT在MWCNT/GCE上峰电位负移120 mV, 峰电流增大约2.5倍, 表明MWCNT/GCE对MT的电化学氧化具有良好的催化作用. 同时测定并计算了MT在MWCNT/GCE上的电极过程动力学参数: 电子转移系数α、电极反应速率常数ks、扩散系数D. 运用差分脉冲伏安法对苦参碱样品含量进行测定, 相对标准偏差为0.12%～2.9%, 加标回收率为98.4%～99.0%. 该方法可用于MT的电化学定量测定.     

EQCM and Fluoroelectrochemical Studies on the Catalytic Oxidation of NADH at a Pencil 8B‐Scrawled Gold Electrode with High Detection Sensitivity

We report for the first time the effective catalytic electrooxidation of nicotinamide adenine dinucleotide (NADH) on the pencil 8B‐scrawled gold electrode of an electrochemical quartz crystal microbalance (EQCM). The EQCM allowed us to quantitatively evaluate the catalytic activity of the pencil‐scrawled Au electrode. With increasing the mass of modified pencil powders, the peak potential for NADH oxidation shifted negatively, with maximum shift of ?0.35 V at saturated pencil modification; the NADH‐oxidation peak current density (j_p) was also notably increased, and the j_p at saturated pencil modification was found to be larger than those at conventional pencil 8B and bare Au electrodes. Sensitive amperometric detection of NADH was achieved at the gold electrode with saturated pencil modification, with low detection potential (0.4 V versus SCE), low detection limit (0.08 μmol L^?1) and wide linear range (0.2–710 μmol L^?1). The fluoroelectrochemical measurements of NADH at bare and pencil‐modified gold electrodes were also conducted with satisfactory results. The convenient and low‐cost modification of pencil powders on the Au electrode may have presented a new functional surface of the EQCM, which is recommended for wider applications to bioelectrochemical studies, especially in view of the EQCM's capability of providing abundant in situ information in relevant processes.     

苯甲酰肼在多壁碳纳米管修饰玻碳电极上的电催化氧化及其电化学动力学性质

研究了苯甲酰肼(BH)在MWCNT/GCE上的电化学行为。实验结果表明,BH在GCE上的直接电化学氧化十分迟缓,无氧化峰出现,但在MWCNT/GCE上BH在0.20 V处出现了一个不可逆氧化峰,且峰电流大幅度增大,表明MWCNT/GCE对BH电化学氧化具有良好的催化作用。同时用计时库仑法(Chro-nocoulometry,CC)和计时电流法(Chronoamperometry,CA)测定了电极过程动力学参数:扩散系数D=8.73×10-5cm2.s-1,电子转移系数α=0.85,电极反应速率常数kf=1.45×10-3s-1。稳态电流-时间实验结果表明,电流响应信号随其浓度成比例增长,响应时间小于6 s,最低响应浓度为1×10-6mol/L。该方法可用于BH电化学定量测定。     

Cyclic voltammetric generation and electrochemical quartz crystal microbalance characterization of passive layer of nickel in a weakly acid medium

The electrochemical quartz crystal microbalance results show that nickel electrodissolution and nickel passivation occur simultaneously. Besides, the anodic transferred charge decreases and the passive layer thickness increases with the number of successive voltammetric cycles. Mass balances across the metal/passive layer/solution have been done from the instantaneous F(dm/dQ) function. A dynamic process for generation of an inner NiO and a Ni(OH)₂ outer passive layers is suggested.     

Determination of beta-carboline alkaloids in foods and beverages by high-performance liquid chromatography with electrochemical detection at a glassy carbon electrode modified with carbon nanotubes

Simple and sensitive methods for the separation and quantification of β-carboline alkaloids in foods and beverages by HPLC with electrochemical detection at carbon nanotubes-modified glassy carbon electrodes (CNTs-GCE) are reported. Electrode modification with multi-wall CNTs produced an improved amperometric response to β-carbolines, in spite of the working medium consisting of methanol:acetonitrile: 0.05 mol L⁻¹ Na₂HPO₄ solution of pH 9.0 (20:20:60). On the contrary to that observed at a bare GCE, a good repeatability of the amperometric measurements carried out at +900 mV versus Ag/AgCl (R.S.D. of 3.2% for i_p, n = 20) was achieved at the CNTs-GCE. Using an Ultrabase C₁₈ column and isocratic elution with the above mentioned mobile phase, a complete resolution of the chromatographic peaks for harmalol, harmaline, norharmane, harmane and harmine, was achieved. Calibration graphs over the 0.25-100 μM range with detection limits ranging between 4 and 19 ng mL⁻¹, were obtained. The HPLC-ED at CNTs-GCE method was applied to the analysis of beer, coffee and cheese samples, spiked with β-carbolines at concentration levels corresponding to those may be found in the respective samples. The steps involved in sample treatment, such as extraction and clean-up, were optimized for each type of sample. Recoveries ranging between 92 and 102% for beer, 92 and 101% for coffee, and 88 and 100% for cheese, at sub-μg mL⁻¹ or g⁻¹ analytes concentration levels were achieved.     

Electrosorption of Os(III)-complex at single-wall carbon nanotubes immobilized on a glassy carbon electrode: application to nanomolar detection of bromate, periodate and iodate

A simple procedure was developed to prepare a glassy carbon electrode modified with single-wall carbon nanotubes (SWCNTs) and Os(III)-complex. The glassy carbon (GC) electrode modified with CNTs was immersed into Os(III)-complex solution (direct deposition) for a short period of time (60 s). 1,4,8,12-Tetraazacyclotetradecane osmium(III) chloride, (Os(III)LCl₂)·ClO₄, irreversibly and strongly adsorbed on SWCNTs immobilized on the surface of GC electrode. Cyclic voltammograms of the Os(III)-complex-incorporated-SWCNTs indicate a pair of well defined and nearly reversible redox couple with surface confined characteristic at wide pH range (1-8). The surface coverage (Γ) and charge transfer rate constant (k_s) of the immobilized Os-complex on SWCNTs were 3.07 × 10⁻⁹ mol cm⁻², 5.5 (±0.2) s⁻¹, 2.94 × 10⁻⁹ mol cm⁻², 7.3 (±0.3) s⁻¹ at buffer solution with pH 2 and 7, respectively, indicate high loading ability of SWCNTs for Os(III) complex and great facilitation of the electron transfer between electroactive redox center and carbon nanotubes immobilized on the electrode surface. Modified electrodes showed higher electrocatalytic activity toward reduction of BrO₃⁻, IO₃⁻ and IO₄⁻ in acidic solutions. The catalytic rate constants for catalytic reduction bromate, periodate and iodate were 3.79 (±0.2) × 10³, 7.32 (±0.2) × 10³ and 1.75 (±0.2) × 10³ M⁻¹ s ⁻¹, respectively. The hydrodynamic amperometry of rotating modified electrode at constant potential (0.3 V) was used for nanomolar detection of selected analytes. Excellent electrochemical reversibility of the redox couple, good reproducibility, high stability, low detection limit, long life time, fast amperometric response time, wide linear concentration range, technical simplicity and possibility of rapid preparation are great advantage of this sensor.     

纳米金/石墨烯修饰电极的制备及其对多巴胺的测定

利用电化学还原方法制备纳米金/石墨烯修饰玻碳电极,研究了多巴胺(DA)在该修饰电极上的电化学行为,建立了电化学测定多巴胺的新方法。结果表明,在磷酸盐缓冲溶液中,此修饰电极对多巴胺的电化学响应具有很好的催化作用。利用差示脉冲伏安技术对多巴胺的电化学氧化进行定量分析,多巴胺的氧化峰电流与其浓度在1.0×10-7～1.0×10-5mol/L范围内呈良好的线性关系,检测限低至4.0×10-8mol/L。该修饰电极适于多巴胺的分析检测。     

Determination of trace amounts of lead and cadmium using a bismuth/glassy carbon composite electrode

We examined the use of a bismuth-glassy carbon (Bi/C) composite electrode for the determination of trace amounts of lead and cadmium. Incorporated bismuth powder in the composite electrode was electrochemically dissolved in 0.1 M acetate buffer (pH 4.5) where nanosized bismuth particles were deposited on the glassy carbon at the reduction potential. The anodic stripping voltammetry on the Bi/C composite electrode exhibited well-defined, sharp and undistorted peaks with a favorable resolution for lead and cadmium. Comparing a non-oxidized Bi/C composite electrode with an in-situ plated bismuth film electrode, the Bi/C composite electrode exhibited superior performance due to its much larger surface area. The limit of detection was 0.41 μg/L for lead and 0.49 μg/L for cadmium. Based on this study, we are able to conclude that various types of composite electrodes for electroanalytical applications can be developed with a prudent combination of electrode materials.     

单层碳纳米管修饰电极上盐酸曲普利啶的电化学行为及其应用研究

应用循环伏安法研究了盐酸曲普利啶在碳纳米管修饰电极上的电化学行为.结果表明:在0.1 mol/L磷酸盐缓冲溶液(pH 6.9)中,盐酸曲普利啶产生一灵敏的氧化峰,其峰电位为0.81 V(vs.Ag/AgCl),峰电流与盐酸曲普利啶在1.0×10-6～1.3×10-4 mol/L浓度范围内呈线性关系,检出限为5.0×10-7mol/L,已用于片剂中盐酸曲普利啶的测定.