三氯生分子印迹传感器的制备及其性能研究

应用分子印迹技术, 以邻苯二胺为功能单体、三氯生为模板, 用循环伏安法在玻碳电极表面合成了性能稳定的三氯生分子印迹聚合膜, 并用方波伏安法对此印迹传感器进行了分析应用研究.     

Thin-film electrochemical sensor for diphenylamine detection using molecularly imprinted polymers

This work reports on the development of a new voltammetric sensor for diphenylamine based on the use of a miniaturized gold electrode modified with a molecularly imprinted polymer recognition element. Molecularly imprinted particles were synthesized ex situ and further entrapped into a poly(3,4-ethylenedioxythiophene) polymer membrane, which was electropolymerized on the surface of the gold electrode. The thickness of the polymer layer was optimized in order to get an adequate diffusion of the target analyte and in turn to achieve an adequate charge transfer at the electrode surface. The resulting modified electrodes showed a selective response to diphenylamine and a high sensitivity compared with the bare gold electrode and the electrode modified with poly(3,4-ethylenedioxythiophene) and non-imprinted polymer particles. The sensor showed a linear range from 4.95 to 115 μM diphenylamine, a limit of detection of 3.9 μM and a good selectivity in the presence of other structurally related molecules. This sensor was successfully applied to the quantification of diphenylamine in spiked apple juice samples.     

Porogen formulations for obtaining molecularly imprinted polymers with optimized binding properties

This paper examines the formulation of new porogenic mixtures used to prepare molecularly imprinted polymers (MIPs) in both thin film and bulk monolith formats. Films were cast by using spin coating to spread a pre-polymerization mixture onto a substrate, and rapid curing of the films was achieved with UV photolysis. The use of a low volatility solvent in combination with a linear polymer porogen resulted in a porous morphology and a 60-fold enhancement in the binding capacity, relative to a non-porous film prepared with a highly volatile solvent and in the absence of the polymer porogen. The opposite effect was seen in MIPs that were prepared in the traditional bulk monolith format, for which the binding efficiency of the MIP decreased monotonically with the concentration of the linear polymer porogen. Furthermore, bulk MIPs that were prepared in the presence of linear polymer porogens exhibited significantly decreased specific surface areas (from 620 to 8 m²/g for samples prepared with pure solvent and 50% polymer porogen, respectively). Despite the change in binding capacity and morphology, the selectivity of the bulk MIPs remained unaffected by the presence of the polymer porogens (approximately 50% chiral selectivity for all bulk MIPs considered). This difference in behavior of the two systems was attributed to the large difference in the kinetics of polymerization.     

水杨酸分子印迹电化学传感器的制备及其性能研究

以水杨酸作为模板分子,通过原位聚合法,在玻碳电极表面合成了水杨酸分子印迹聚合物膜,并用方波伏安法对该印迹电极进行了分析研究.当吸附时间为7 min时,印迹电极对水杨酸浓度响应的线性范围为1.0×10-5~2.6×10-5mol/L,检出限(S/N=3)为2.0×10-6mol/L,同一支印迹电极对水杨酸响应值的RSD为...     

Electrochemical sensing with electrodes modified with molecularly imprinted polymer films

This article summarises our work on the development of voltammetric sensors based on molecularly imprinted polymers. Several recognition elements and integration strategies were used:1.membranes electropolymerised at the electrode surface; 2.casting of polymeric membranes by drop-coating a solution of pre-formed polymer (polyphosphazene) and template in a low-boiling-point solvent on to the electrode surface; 3.preparation of composite membranes containing conductive material (graphite or carbon black), acrylic-type molecularly imprinted polymers (small particle size), and PVC as binder; and 4.in-situ polymerisation of a thin layer of acrylic imprinted polymer deposited on the electrode surface by spin coating.All the options evaluated offer the possibility of controlling electrode characteristics such as hydrophobic/hydrophilic character, permeability, or film thickness, which are essential for obtaining good sensor performance.     

Chromatographic characterization of molecularly imprinted polymers

Recent efforts in the investigation of chromatographic characterization of molecularly imprinted polymers (MIPs) have focused mainly on the nature of heterogeneous binding sites. More data on the thermodynamics than on the kinetic features of MIP columns have been published. The present article addresses the sources of peak broadening and tailing, which are the main drawbacks often associated with imprinted polymers in chromatography for practical applications. With use of the theory of nonlinear chromatography, the peak properties of a MIP column, including the retention and peak broadening and tailing, can be well interpreted. Efforts to improve chromatographic efficiency using MIPs prepared by approaches different from the conventional method, including covalent imprinting and the format of uniformly sized spherical microbeads, are reviewed and discussed. This review leads to the conclusion that nonlinear chromatography theory is useful for characterizing chromatographic features of MIP columns, since a MIP is essentially an affinity-based chromatographic stationary phase. We expect more theoretical and experimental studies on the kinetic aspects of MIP columns, especially the factors influencing the apparent rate constant, as well as the analysis of the influences of mobile-phase composition on the chromatographic performance. In addition to revealing the affinity interaction by molecular recognition, slow nonspecific interactions which may be inherited from the imperfect imprinting and may be involved in the rebinding of the template to MIPs also need to be characterized. Figure The peak broadening and tailing associated often with molecularly imprinted polymers (MIPs) in column chromatography for practical applications can be well characterized by the theory of nonlinear chromatography.     

Acetylene black paste electrode modified with molecularly imprinted polymers/graphene for the determination of bisphenol A

A novel nanocomposite of molecularly imprinted polymers and graphene sheets was fabricated and used to obtain a highly conductive acetylene black paste electrode with high conductivity for the detection of bisphenol A. The two‐dimensional structure and the chemical functionality of graphene provide an excellent surface for the enhancement of the sensitivity of the electrochemical sensor and the specificity of molecularly imprinted polymers to improve detection of bisphenol A. The synergistic effect between graphene and molecularly imprinted polymers confers the nanocomposite with superior conductivity, broadened effective surface area and outstanding electrochemical performance. Factors affecting the performance of the imprinted sensor such as molecularly imprinted polymers concentration, foster time and scan rate are discussed. The sensor successfully detects bisphenol A with a wide linear range of 3.21 × 10^?10 to 2.8 × 10^?1 g/L (R = 0.995) and a detection limit of 9.63 × 10^?11g/L. The fabricated sensor also possessed high selectivity and stability and exhibits potential for environmental detection of contaminants and food safety inspection.     

Molecularly imprinted conducting polymer based electrochemical sensor for detection of atrazine

An original electrochemical sensor based on molecularly imprinted conducting polymer (MICP) is developed, which enables the recognition of a small pesticide target molecule, atrazine. The conjugated MICP, poly(3,4-ethylenedioxythiophene-co-thiophene-acetic acid), has been electrochemically synthesized onto a platinum electrode following two steps: (i) polymerization of comonomers in the presence of atrazine, already associated to the acetic acid substituent through hydrogen bonding, and (ii) removal of atrazine from the resulting polymer, which leaves the acetic acid substituents open for association with atrazine. The obtained sensing MICP is highly specific towards newly added atrazine and the recognition can be quantitatively analyzed by the variation of the cyclic voltammogram of MICP. The developed sensor shows remarkable properties: selectivity towards triazinic family, large range of detection (10⁻⁹ mol L⁻¹ to 1.5 × 10⁻² mol L⁻¹ in atrazine) and low detection threshold (10⁻⁷ mol L⁻¹).     

Recent advances in synthetic methods and applications of photo-luminescent molecularly imprinted polymers

Molecularly imprinted polymers with photo-luminescent properties (PLMIPs) and PLMIPs-based hybrids have been widely studied in recent years because of their integrated merits from molecular imprinting technologies and PL properties. PLMIPs have superior capabilities for signal transducer and molecular recognition, exhibiting great potential as the constructing platforms for promising applications. During the past decade, numerous researches have mentioned PLMIPs. In terms of unique merits and important applications of PLMIPs, a timely, comprehensive and in-depth review on PLMIPs is significant and is still lacking currently. This review systematically summarizes recent advances of PLMIPs, focusing on different synthetic methods and applications. Based on different components and structures, PLMIPs include different categories. Synthetic methods majorly involve encapsulation polymerization of nanomaterials (fluorophores) into MIPs, copolymerization of fluorescent monomers, electro-polymerization, photo-polymerization, etc. Various engineering structures and luminescence properties of PLMIPs are highlighted Potential applications of PLMIPs mention significant research fields, including chemo/bio-detection, bio-imaging, functionalized separation materials, versatile sensing materials, optical devices, etc. We also discuss present status, probable challenges and future perspectives of PLMIPs. This review is desirable for scientists from broad research fields and can promote further development of MIPs-based functional materials, luminescent hybrid materials and other advanced optical materials.     

Trimethoprim-selective electrodes with molecularly imprinted polymers acting as ionophores and potentiometric transduction on graphite solid-contact

This work proposes a new biomimetic sensor material for trimethoprim. It is prepared by means of radical polymerization, having trimethylolpropane trimethacrylate as cross-linker, benzoyl peroxide as radicalar iniciator, chloroform as porogenic solvent, and methacrylic acid and 2-vinyl pyridine as monomers. Different percentages of sensor in a range between 1 and 6% were studied. Their behavior was compared to that obtained with ion-exchanger quaternary ammonium salt (additive tetrakis(p-chlorophenyl)borate or tetraphenylborate). The effect of an anionic additive in the sensing membrane was also tested.Trimethoprim sensors with 1% of imprinted particles from methacrylic acid monomers showed the best response in terms of slope (59.7 mV/decade) and detection limit (4.01 × 10^− 7 mol/L). These electrodes displayed also a good selectivity towards nickel, manganese aluminium, ammonium, lead, potassium, sodium, iron, chromium, sulfadiazine, alanine, cysteine, tryptophan, valine and glycine. The sensors were not affected by pH changes from 2 to 6. They were successfully applied to the analysis of water from aquaculture.     

Preparation and characterization of monodisperse molecularly imprinted polymers for the recognition and enrichment of oleanolic acid

Monodisperse molecularly imprinted polymers for oleanolic acid were successfully prepared by a precipitation polymerization method using oleanolic acid as a template, methacrylic acid as a functional monomer, and divinylbenzene/ethylene glycol dimethacrylate as a crosslinker in a mixture of acetonitrile and ethanol (3:1, v/v). The imprinted polymers and nonimprinted polymers were characterized by using scanning electron microscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The resulting imprinted polymers had average diameters of 3.15 μm and monodispersity values of 1.024. The results clearly demonstrate that use of ethanol as a cosolvent is indeed exceedingly effective in promoting the dissolution of oleanolic acid and in obtaining uniform microspheres. Molecular recognition properties and binding capability to oleanolic acid were evaluated by adsorption testing, which indicated that the imprinted polymers displayed optimal binding performance with a maximum adsorption capacity of 17.3 mg/g and a binding saturation time of 80 min. Meanwhile, the produced imprinted polymers exhibited higher selectivity to oleanolic acid than that for ursolic acid and rhein. Herein, the studies can provide theoretical and experimental references for the oleanolic acid molecular imprinted system.     

Novel stereoselective molecularly imprinted polymers via ring-opening metathesis polymerisation

Stereoselective molecularly imprinted polymers (MIPs) have been synthesised via ring-opening metathesis polymerisation, in essentially, quantitative yield. A covalent imprinting strategy was followed during the network formation of the chiral sorbent. Recognition of the substrate however involved non-covalent interactions; a combination of hydrogen bonding and the chiral environment presented by the imprinted cavities. The enantiomeric excess achievable with these new MIPs is solvent dependent and stereoselectivities of up to 20% e.e. (separation factor α=2.2) were found in batch equilibrations.     

Review of the recent progress in photoresponsive molecularly imprinted polymers containing azobenzene chromophores

Photoresponsive molecularly imprinted polymers (PMIPs) containing azobenzene have received wide research attention in recent years and made notable achievements. This article reviews the recent developments on PMIPs containing azobenzene. Topics include the following: (i) brief introduction of azobenzene, molecularly imprinted polymers, and PMIPs containing azobenzene; (ii) progress in functional monomers, cross-linkers, and polymerization conditions; (iii) preparation methods, properties, applications, as well as advantages and disadvantages of conventional PMIPs; (iv) substrate, preparation method, and applications of photoresponsive surface molecularly imprinted polymers; and (v) some perspectives for further development of PMIPs containing azobenzene.     

Validation and application of modeling algorithms for the design of molecularly imprinted polymers

In the study, four different semiempirical algorithms, modified neglect of diatomic overlap, a reparameterization of Austin Model 1, complete neglect of differential overlap and typed neglect of differential overlap, have been applied for the energy optimization of template, monomer, and template‐monomer complexes of imprinted polymers. For phosmet‐, estrone‐, and metolcarb‐imprinted polymers, the binding energies of template‐monomer complexes were calculated and the docking configures were assessed in different molar ratio of template/monomer. It was found that two algorithms were not suitable for calculating the binding energy in template‐monomers complex system. For the other algorithms, the obtained optimum molar ratio of template and monomers were consistent with the experimental results. Therefore, two algorithms have been selected and applied for the preparation of enrofloxacin‐imprinted polymers. Meanwhile using a different molar ratio of template and monomer, we prepared imprinted polymers and nonimprinted polymers, and evaluated the adsorption to template. It was verified that the experimental results were in good agreement with the modeling results. As a result, the semiempirical algorithm had certain feasibility in designing the preparation of imprinted polymers.     

Citrinin selective molecularly imprinted polymers for SPE

Molecularly imprinted polymers (MIPs) for citrinin (Cit) with 1‐hydroxy‐2‐naphthoic acid (HNA) as mimic template were prepared and the molecularly imprinted SPE method was developed for the detection of Cit in rice with HPLC. The adsorption properties of HNA and Cit on the MIPs and nonimprinted polymers were investigated. It proved that MIPs showed higher selectivity adsorption to HNA and Cit than nonimprinted polymers were. The recoveries of Cit in rice were in the range of 86.7–97.7%. The spiked rice samples and five rice samples in Beijing market were detected using molecularly imprinted SPE method and satisfied results were obtained as discussed in this article.     

Capturing molecules with templated materials--analysis and rational design of molecularly imprinted polymers

The creation of synthetic tailor-made receptors capable of recognizing desired molecular targets with high affinity and selectivity is a persistent long-term goal for researchers in the fields of chemical, biological, and pharmaceutical research. Compared to biomacromolecular receptors, these synthetic receptors promise simplified production and processing, less costs, and more robust receptor architectures. During recent decades, molecularly imprinted polymers (MIPs) are widely considered mimics of natural molecular receptors suitable for a diversity of applications ranging from biomimetic sensors, to separations and biocatalysis.A remaining challenge for the next generation of MIPs is the synthesis of deliberately designed and highly efficient receptor architectures suitable for recognizing biologically relevant molecules, for which natural receptors are either not prevalent, or difficult to isolate and utilize. Hence, this review discusses recent advances in synthetic receptor technology for biomolecules (e.g. drugs, amino acids, steroids, proteins, entire cells, etc.) via molecular imprinting techniques. Surface imprinting methods and epitope imprinting approaches have been introduced for protein recognition at imprinted surfaces. Imprinting techniques in aqueous solution or organic-water co-solvents have been introduced avoiding denaturation of biomolecules during MIP synthesis. In addition, improved bioreactivity of entire enzyme or active site mimics generated by molecular imprinting will be highlighted. Finally, the emerging importance of molecular modeling and molecular dynamics studies detailing the intermolecular interactions between the template species, the porogenic solvent molecules, and the involved monomer and cross-linker in the pre-polymerization solution will be addressed yielding a rational approach toward next-generation MIP technology.     

Selective enrichment and separation of phosphotyrosine peptides by thermosensitive molecularly imprinted polymers

Novel thermosensitive molecularly imprinted polymers were successfully prepared using the epitope imprinting approach in the presence of the mimic template phenylphosphonic acid, the functional monomer vinylphosphonic acid‐Ti⁴⁺, the temperature‐sensitive monomer N‐isopropylacrylamide and the crosslinker N,N′‐methylenebisacrylamide. The ratio of the template/thermosensitive monomers/crosslinker was optimized, and when the ratio was 2:2:1, the prepared thermosensitive molecularly imprinted polymers had the highest imprinting factor. The synthetic thermosensitive molecularly imprinted polymers were characterized by Fourier transform infrared spectroscopy to reveal the combination and elution processes of the template. Then, the adsorption capacity and thermosensitivity was measured. When the temperature was 28°C, the imprinting factor was the highest. The selectivity and adsorption capacity of the thermosensitive molecularly imprinted polymers for phosphotyrosine peptides from a mixture of three tailor‐made peptides were measured by high‐performance liquid chromatography. The results showed that the thermosensitive molecularly imprinted polymers have good selectivity for phosphotyrosine peptides. Finally, the imprinted hydrogels were applied to specifically adsorb phosphotyrosine peptides from a sample mixture containing phosphotyrosine and a tryptic digest of β‐casein, which demonstrated high selectivity. After four rebinding cycles, 78.9% adsorption efficiency was still retained.     

A novel molecularly imprinted sensor for selectively probing imipramine created on ITO electrodes modified by Au nanoparticles

A sensitive molecularly imprinted electrochemical sensor was created for selective detection of a tricyclic antidepressant imipramine by combination of Au nanoparticles (Au-NPs) with a thin molecularly imprinted film. The sensor was fabricated onto the indium tin oxide (ITO) electrode via stepwise modification of Au-NPs by self-assembly and a thin film of molecularly imprinted polymers (MIPs) via sol-gel technology. It was observed that the molecularly imprinted film displayed excellent selectivity towards the target molecule imipramine. Meanwhile, the introduced Au-NPs exhibited noticeable catalytic activities towards imipramine oxidation, which remarkably enhanced the sensitivity of the imprinted film. Due to such combination, the as-prepared sensor responded quickly to imipramine, within only 1 min of incubation. The differential voltammetric anodic peak current was linear to the logarithm of imipramine concentration in the range from 5.0 × 10⁻⁶ to 1.0 × 10⁻³ mol L⁻¹, and the detection limits obtained was 1.0 × 10⁻⁹ mol L⁻¹. This method proposed was successfully applied to the determination of imipramine in drug tablets, and proven to be reliable compared with conventional UV method. These results reveal that such a sensor fulfills the selectivity, sensitivity, speed and simplicity requirements for imipramine detection, and provides possibilities of clinical application in physiological fluids.     

Preparation of highly selective solid-phase extractants for Cibacron reactive dyes using molecularly imprinted polymers

Selective polymeric extractants were prepared for preconcentration of Cibacron reactive red dye, a dye that is often applied with Cibacron reactive blue and Cibacron reactive yellow for dyeing of fabrics. The best extractant was fabricated (in chloroform) using methacrylic acid (as monomer), ethylene glycol dimethacrylate (as crosslinker), AIBN (as initiator for polymerization), and red dye as template molecule, with a molar stoichiometric ratio of 8.0:40.0:2.5:0.63, respectively. The structure of the molecularly imprinted polymer (MIP) was robust, and resisted dissolution up to 260 °C. Compared with the un-imprinted polymer, the imprinted product has a large specific surface area which improved its adsorption capacity. The effect of imprinting was obvious from the adsorption capacity measured at pH 4 for red dye (the imprinted molecule), which was increased from 24.0 to 79.3 mg g⁻¹ after imprinting. Equilibrium adsorption studies revealed that the dye-imprinted-polymer enables efficient extraction of red dye even in the presence of blue and yellow dyes which have similar chemical natures to the red dye. The selectivity coefficients S _{red dye/dye}, were 13.9 and 17.1 relative to the yellow and blue dyes, respectively. The MIP was found to be effective for red dye preconcentration, with a preconcentration factor of 100, from tap water and treated textile wastewater. The factors affecting extraction of red dye by the MIP were studied and optimized. Under the optimized extraction conditions, red dye was selectively quantified in the presence of other competing dyes at a concentration of 20 μg L⁻¹ from different water systems with satisfactory recoveries (91–95%) and RSD values (∼5.0%).     

Construction of a novel electrochemical sensor based on molecularly imprinted polymers for the selective determination of chlorpyrifos in real samples

We present a novel electrochemical sensor based on an electrode modified with molecularly imprinted polymers for the detection of chlorpyrifos. The modified electrode was constructed by the synthesis of molecularly imprinted polymers by a precipitation method then coated on a glassy carbon electrode. The surface morphology of the modified electrode was characterized by using field‐emission scanning electron microscopy and transmission electron microscopy. The performance of the imprinted sensor was thoroughly investigated by using cyclic voltammetry and differential pulse voltammetry. The imprinted electrochemical sensor displayed high repeatability, stability, and selectivity towards the template molecules. Under the optimal experimental conditions, the peak current response of the imprinted electrochemical sensor was linearly related to the concentration of chlorpyrifos over the range 1 × 10⁻¹⁰–1 × 10⁻⁵ mol/L with a limit of detection of 4.08 × 10⁻⁹ mol/L (signal‐to‐noise ratio = 3). Furthermore, the proposed molecularly imprinted electrochemical sensor was applied to the determination of chlorpyrifos in the complicated matrixes of real samples with satisfactory results. Therefore, the molecularly imprinted polymers based electrochemical sensor might provide a highly selective, rapid, and cost‐effective method for chlorpyrifos determination and related analysis.