N-methyl-substituted aromatic polyamides

A series of N-methyl-substituted aromatic polyamides derived from the secondary aromatic diamines 4,4′-bis(methylamino)diphenylmethane, 3,3′-bis(methylamino)diphenylmethane, 4,4′-bis(methylamino)benzophenone or 3,3′-bis(methylamino)benzophenone and isophthaloyl dichloride, and terephthaloyl dichloride or 3,3′-diphenylmethane dicarboxylic acid dichloride was prepared by high-temperature solution polymerization in s-tetrachloroethane. Compared with analogous unsubstituted and partly N-methylated aromatic polyamides, the full N-methylated polyamides exhibited significantly lower glass transition temperatures (T_g), reduced crystallinity, improved thermal stability, and good solubility in chlorinated solvents.     

Hyperbranched carbosilane oxazoline-macromonomers: polymerization and coupling to a trimesic acid core

Attachment of oxazoline-based hyperbranched macromonomers to a trimesic acid core affording trimers of the hyperbranched fragments as well as polymerization of the oxazoline groups is reported. Polymerization and copolymerization with 2-phenyl-1,3-oxazoline were investigated for two macromonomers (M _w = 1700 and 8 000, respectively), resulting in hyperbranched analogs of combburst polymers. Homopolymerization of the macromonomers yielded a degree of polymerization DP ≈ 15. Hyperbranched trimers and the polyethyleneimines with apolar hyperbranched carbosilane side-chains form superstructures in solution and in bulk.     

Coordination Homopolymerization of ω–undecenyl Poly(styrene-block-isoprene) Macromonomers in the Presence of CGC-Ti/MAO Complexes

This paper deals with the coordination homopolymerization of ω–undecenyl poly(styrene-block-isoprene) macromonomers. The synthesis of the macromonomers made use of an anionic living poly(styrene-block-isoprene) copolymer which is deactivated at low temperature by 11-bromo-1-undecene. The ability of these macromonomers to get involved in coordination homopolymerization in the presence of selected titanium catalysts was discussed. Special emphasis was given to the influence of polymerization temperature, macromonomer molar mass and concentration on the yield of homopolymerization and average degree of polymerization (DP_n). In the presence of the CGC-Ti/MAO catalyst, macromonomer conversion, determined by SEC, was between 35 to 52 wt.-%, and DP_n was between 5 to 14 depending upon the experimental conditions. However, as revealed by SEC/LS, the resulting comb-shaped polymers (PE-graft-(PI-block-PS), are characterized by sharp molar distributions. Increasing macromonomer molar mass, led to only a slight decrease of DP_n whereas conversion increased moderately. Other titanium catalysts such as CpTiCl₃/MAO and Cp*TiCl₃/MAO only caused macromonomer dimerization.     

New Materials Designed by Coordination Polymerization of ω-undecenyl Macromonomers

The major part of the present paper discusses the ability of well-defined ω-undecenyl polystyrene, polyisoprene or poly(styrene-block-isoprene) macromonomers to undergo coordination homopolymerization in the presence of selected titanium catalysts. Special emphasis is given to the influence of the nature of the catalyst, the polymerization temperature and the macromonomer molar mass and concentration on homopolymerization yield and average degree of homopolymerization (DP_n). Titanium-based catalytic systems such as CpTiCl₃/MAO and Cp*TiCl₃/MAO only yielded dimers. The use of the homogeneous metallocene catalyst with constrained ligand geometry (CGC-Ti/MAO) having an open active site, significantly improved the degree of polymerization. Increasing macromonomer molar mass, causes only a slight decrease of DP_n whereas conversion increased moderately. The final section briefly discusses the copolymerization of ω-undecenyl polystyrene macromonomers with ethylene in the presence of Versipol™ catalysts.     

Study of kinetics of thermal degradation and to determine the activation energies of polyamides based on s-triazine

A series of ten polyamides was prepared by the high-temperature polycondensation of 4,6-bis(N-(4-(benzoylchloride)amino))-2-(N-phenyl- piperazin-1-yl)-1,3,5-triazine with different aromatic and aliphatic diamines. The synthesized polyamides were analyzed by physico-chemical properties such as solubility, density, viscosity etc. The structure of prepared polyamides was evaluated by ¹H NMR and FTIR spectrum. Thermogravimetric analysis used to study the kinetics of thermal degradation of some synthesized polyamides. Broido, Horowitz & Metzger, Coats Redfern and Chan et al. models were applied to respective thermograms to determine the activation energy (E_a). Activation energy data shows that the polyamides obtained from aromatic diamine has greater stability than the polyamides obtained from aliphatic amine.     

Controlling grafting density and side chain length in poly(n‐butyl acrylate) by ATRP copolymerization of macromonomers

Atom transfer radical polymerization (ATRP) was used for the preparation and subsequent copolymerization of two acryloyl‐terminated poly(n‐butyl acrylate) macromonomers with different degrees of polymerization (DP_nBA = 25 and 42). Homopolymerization of the higher molecular weight macromonomer ( MM1 ; PnBA₄₂‐A, M_n = 5600, DP_MM = 42, M_w/M_n = 1.18) resulted in preparation of a densely grafted polymer with a narrow molecular weight distribution (M_w/M_n = 1.14), but with the limited degree of polymerization DP = 12. The ultimate degree of homopolymerization for the lower molecular weight macromonomer ( MM2 ; PnBA₂₅‐A, M_n = 3400, DP_MM = 25, M_w/M_n = 1.20) was higher, and DP increased from 12 to 22. The limited DP could be because of progressively increasing steric congestion for macromonomers in approaching the growing chain ends of densely grafted polymers. When MMs were copolymerized with nBA, the reactivity of MM was nearly the same as that of nBA monomer irrespective of the differences in the degree of polymerization of the MMs and the initial molar ratio of nBA to MM. Well‐defined graft polymers with different lengths of backbone and side chains, and different graft density were successfully prepared by “grafting through” ATRP. Tadpole‐shaped and dumbbell‐shaped graft polymers were also synthesized by ATRP. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5454–5467, 2006     

Aromatic Polyamides of 2,6-Naphthalenedicarboxylic Acid

Wholly aromatic polyamides have been prepared by the interfacial polycondensation of 2,6-naphthalenedicarboxylic acid chloride with m-phenylenediamine. Also, copolyamides with isophthaloyl or terephthaloyl chlorides and the naphthalene diacid chloride were synthesized. The resultant polyamides were amorphous or slightly crystalline as determined by x-ray diffraction, had tensile properties characteristic of hard, strong materials, and were more thermally stable than aromatic polyamides prepared solely from benzene diacid chlorides.     

Thermal properties of wholly aromatic polyamides

Various wholly aromatic polyamides based on m-and p-phenylene diamines and isophthaloyl and terephthaloyl chloride have been synthesized and their thermal properties and oxygen index values have been studied. The effect of different substituents on the aromatic ring of the diamine have been explored by comparing their differential thermal analysis (DTA) and thermogravimetric analysis (TGA) behavior, their relative char yields at 700°C, and their oxygen indices. The ? Cl, ? NO₂, and ? OH substituted polyamides have been found to produce the highest char yields. The high char yields are probably associated with crosslinking occurring at high temperatures. Attempts at correlating char yield with oxygen index indicated enhancement for the chlorosubstituted aramids.     

Soluble aromatic polyamides modified by incorporation of 1,2,4-triazole and pentadecyl units into the backbone of polymer

Abstract

A new series of soluble aromatic polyamides was synthesized by low temperature solution polycondensation of novel aromatic diamine namely 3,5-bis-(4′-amino phenyl)-4-(4″-methoxy-2″-pentadecyl phenyl) 1,2,4-triazole (VII) with aromatic diacid chlorides, viz. isophthaloyl chloride (IPC) and terephthaloyl chloride (TPC). The aromaticdiamine (VII) was characterized by elemental analysis, FT-IR, NMR (¹H, ¹³C), and mass spectrometry. Copolyamides were also synthesized by employing various mole proportions of IPC and TPC with diamine (VII). Inherent viscosities of these polyamides were in the range of 0.50–0.65 dL/g in DMAc, indicating formation of moderate to high molecular weight of polyamides. These polyamides showed good solubility in polar aprotic solvents such as N,N-Dimethyl acetamide (DMAc), N-Methyl 2-pyrrolidone (NMP), N, N, Dimethyl formamide (DMF), and Dimethyl sulphoxide (DMSO), which may be due to incorporation of pendant methoxyphenyl moiety with pentadecyl units. The amorphous morphology of polyamides as evidenced by XRD. These polyamides had lower glass transition temperatures; as determined by DSC, compared to the T_g of conventional aromatic polyamides due to internal plasticization effect of long alkyl pentadecyl group. Polymers showed good thermal stability, with initial decomposition temperature above 300?°C.     

Multicomponent Polymers of Poly(Lactic Acid) Macromonomers with Methacrylate Terminal and Copolymers of Poly(2-Hydroxyethyl Methacrylate)

Abstract

Poly(lactic acid) macromonomers with methacrylate terminal functionality have been synthesized from the cyclic dimer of lactic acid (referred to as lactide) with 2-hydroxyethyl methacrylate (HEMA) as initiator and stannous 2-ethyl hexanoate as catalyst. The macromonomers were characterized with FT-IR, NMR, GPC, DSC, WAXS, and CD. The molecular weights of the macromonomers ranging from M _n 1425 to 19,169 are predictable from the lactide/HEMA ratio in the polymerization feeds. The properties of the macromonomers vary with the stereochemistry of the lactide and the composition. Circular dichroism measurements demonstrate that there is little racemization during polymerization.     

Synthesis and characterization of N-phenylated aromatic polyamides from N-silylated dianilino compounds and aromatic diacid chlorides

N-Phenylated aromatic polyamides of high molecular weights were synthesized by the hightemperature solution polycondensation of N,N′ -di(trimethylsilyl)-substituted dianilino compounds derived from p-dianilinobenzene, bis(4-anllinophenyl) ether, and α,α′-dianilino-p-xylene, with isophthaloyl and terephthaloyl chloride. Almost all of the N-phenylated polyamides were amorphous, and soluble in a variety of organic solvents including dimethylformamide, m-cresol, and chloroform. Transparent and flexible films of these polymers could be cast from the dimethylformamide solutions. Four wholly aromatic polyamides had glass transition temperatures in the range of 195–255°C, and began to lose weight around 400°C in air.     

Aliphatic-aromatic poly(ether amide)s containing oxyethylene units. Synthesis and characterization

The synthesis and characterization of aromatic polyamides containing oxyethylene units is reported, and the differences observed in polycondensation yields, molecular weights, and molecular weight distributions, as a function of the method of synthesis, are discussed. Four diamines containing oxyethylene units and aromatic rings, meta and para oriented, and their corresponding hydrochlorides were prepared as condensation monomers to be combined with isophthaloyl chloride (IPC) and terephthaloyl chloride (TPC). High molecular weight polyamides were obtained by interfacial and low-temperature solution methods. Values of (OVERLINE)M(/OVERLINE)_n up to 6 × 10⁴ g/mol and (OVERLINE)M(/OVERLINE)_w up to 2 × 10⁵ g/mol could be measured by gel permeation chromatography using aromatic polyamide standards, and values of (OVERLINE)M(/OVERLINE)_n up to 2 × 10⁵ g/mol and (OVERLINE)M(/OVERLINE)_w up to 5 × 10⁵ g/mol by using polystyrene standards. © 1996 John Wiley & Sons, Inc.     

Gradient graft copolymers derived from PEO‐based macromonomers

Atom transfer radical polymerization (ATRP) of two poly(ethylene oxide) (PEO) macromonomers, with different polymerization degrees (DP_n) and different end groups, was conducted in solution via the grafting through method. Selection of a PEO methacrylate with a methyl end‐group (PEOMeMA, DP_PEO = 23) and a PEO acrylate end‐capped by a phenyl ring (PEOPhA, DP_PEO = 4) for the copolymerization led to a spontaneous gradient of PEO grafts along the copolymer backbone. Such a composition was formed because of significantly different reactivities of the two PEO macromonomers. The resulting copolymer has PEOMeMA at one end of the polymer chain, gradually changing through hetero‐sequences of PEOPhA at the other chain end. An increase in the initial feed ratio of PEO acrylate reduced the rate of change in the shape of the gradient. Amorphous–crystalline structure in the copolymers was demonstrated by DSC and WAXS. The mechanical measurements of copolymers consisting of an amorphous PEOPhA and crystallizable PEOMeMA segments indicated elastomeric properties in the range of a soft rubber (G′ ～ 10⁴ Pa, G′ ? G″). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1347–1356, 2006     

Polymerization and self‐assembly of thermally responsive in‐chain functionalized double‐hydrophilic macromonomers

Double‐hydrophilic in‐chain functionalized macromonomers consisting of poly(N‐isopropylacrylamide) (PNIPAM) and poly(ethylene oxide) were prepared by a multistep procedure including esterification of PNIPAM monoester of maleic acid with α‐methoxy‐ω‐hydroxypolyoxyethylene or its amidation with α‐methoxy‐ω‐aminopolyoxyethylene. The polymerization of the macromonomers was carried out in aqueous solutions. The temperature was the key parameter controlling the polymerization process that was performed in the organized domains formed by the macromonomers below and above the phase transition temperature (T_tr). Polymacromonomers with higher degrees of polymerization were prepared at temperatures just below the T_tr. Static light scattering measurements on dilute aqueous solutions of thermally‐responsive macromonomers and their polymerization products demonstrated that they formed aggregates below the T_tr. Supramolecular structures with low density cores, formed by the polymacromonomers at room temperature, were imaged by SEM. Morphological tuning was achieved by varying both the composition of the copolymer and the concentration of the aqueous solution. The rheological behavior of the polymacromonomers in 25 wt % aqueous solution was compared to that of the respective macromonomers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4720–4732, 2007     

Fabrication of biodegradable poly(trimethylene carbonate) networks for potential tissue engineering scaffold applications

Biodegradable poly(trimethylene carbonate) (PTMC) networks were prepared by photopolymerization of linear (L)‐ and star (S)‐shaped PTMC macromonomers for potential tissue engineering scaffold applications. The L‐ (M_n, 6400) and S‐shaped (M_n, 5880) PTMC macromonomers were synthesized using 1,4‐butane diol and 2‐ethyl‐ 2‐hydroxyl‐propane‐1,3‐diol co‐initiated ring‐opening polymerization of trimethylene carbonate (TMC) in the presence of stannous octoate and subsequent acrylation with acryloyl chloride. Chemical structures of the PTMC macromonomers and their corresponding networks were characterized by ¹H NMR and ¹³C NMR spectroscopy. The human endothelial cell line, EA.hy926 was used to test the biocompatibility, cell adhesion, and proliferation behavior of both PTMC networks. The PTMC networks made from the S‐shaped macromonomers exhibited superior cell adhesion and proliferation behavior than those made of the linear macromonomers. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis of Styrenic‐Terminated Methacrylate Macromonomers by Nitroanion‐Initiated Living Anionic Polymerization

N‐Isopropyl‐4‐vinylbenzylamine (PVBA) was synthesized and used as an initiator for the polymerization of methacrylates to synthesize macromonomers with terminal styrenic moieties. LiPVBA initiated a living polymerization and block copolymerization of methyl methacrylate, 2‐(N,N‐dimethylamino)ethyl methacrylate and tert‐butyl methacrylate and produced polymers having well‐controlled molecular weights and very low polydispersities (M̄_w/M̄_n < 1.1) in quantitative yield. ¹H NMR analysis revealed that the polymers contained terminal 4‐vinylbenzyl groups. The macromonomers were reactive in the copolymerization with styrene.     

Preparation and properties of N-phenylated aromatic polyamides from N,N′-diphenyl-p-phenylenediamine and aromatic diacid chlorides

N-Phenylated aromatic polyamides and copolyamides derived from N,N′-diphenyl-p-phenylenediamine, isophthaloyl, and terephthaloyl chloride were prepared by high-temperature solution polycondensation in anisole at 155°C. Factors that influenced the reaction, such as monomer concentration, solvent, temperature, and time, were studied to determine the optimum conditions for the preparation of high molecular weight polymers. Compared with analogous unsubstituted aromatic polyamides, the N-phenylated polymers exhibited better solubility in chlorinated and amide solvents, reduced crystallinity, and lower glass transition temperatures (above 200°C). All polymers except the polyterephthalamide could be solvent-cast, as well as hot-pressed, into transparent flexible films.     

Novel block ionomers II. Synthesis and characterization of polyisobutylene‐based block cationomers

Various novel block cationomers consisting of polyisobutylene (PIB) and poly[2‐(dimethylamino)ethyl methacrylate] (PDMAEMA) segments were synthesized and characterized. The specific targets were various molecular weight diblocks (PIB‐b‐PDMAEMA⁺) and triblocks (PDMAEMA⁺‐b‐PIB‐b‐PDMAEMA⁺), with the PIB blocks in the DP_n = 50–200 range (number‐average molecular weight = 3,000–9000 g/mol) connected to blocks of PDMAEMA⁺ cations in the DP_n = 5–20 range (where DP is the number‐average degree of polymerization). The overall synthetic strategy for the preparation of these block cationomers had four steps: (1) synthesis by living cationic polymerization of mono‐ and diallyltelechelic polyisobutylenes, (2) end‐group transformation to obtain PIBs fitted with termini capable of mediating the atom transfer radical polymerization (ATRP) of DMAEMA, (3) ATRP of DMAEMA, and (4) quaternization of PDMAEMA to PDMAEMA ⁺I^? by CH₃I. Scheme 1 shows the microarchitecture and outlines the synthesis route. Kinetic and model experiments provided guidance for developing convenient synthesis methods. The microarchitecture of PIB–PDMAEMA di‐ and triblocks and the corresponding block cationomers were confirmed by ¹H NMR and FTIR spectroscopy and solubility studies. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3679–3691, 2002     

三甲基苯二胺芳香聚酰胺的结构与性能

利用ＩＲ，ＷＡＸＤ，ＤＳＣ及ＴＧ等表征了多取代芳香族聚酞胺的结构与性能。     

Study on wholly aromatic polyamides containing methyl-substituted phenylene linkage

In order to study the influence of chemical modification on properties of polyamides, wholly aromatic polyamides have been synthesized from p-phenylenediamine, its 2,5-dimethyl and 2-methyl derivatives, m-phenylenediamine, its 2-methyl and 4-methyl derivatives, and terephthaloyl and isophthaloyl dichlorides by solution polycondensation at low temperature. The thermal stability and solubility of the methyl-substituted polyamides were compared with those of unsubstituted ones. The introduction of methyl groups in a polymeric chain led to a decrease in their thermal stability to different degrees depending on the positions of methyl groups, accompanied by an increase in their solubility. The unsymmetrical introduction of methyl groups in benzene rings had a greater effect on the increase in solubility of polyamide than did symmetrical methyl groups.