微流动注射进样-加热雾室-等离子体质谱测定血清中的铂

开发了一种基于雾化室加热的微流动注射进样系统,并用于血清中Pt的测定。该进样系统由微量毛细管雾化器、加热微型雾化室、八通道十六孔多功能旋转阀、蠕动泵和注射泵组成。研究了雾化室尺寸、加热温度和采样环体积对信号强度的影响。当雾化室内径为9 mm、加热段长度为6 cm,雾化室温度90 ℃,采样环体积为5 μL时,195Pt的信号强度提高了2.31倍,同时信号精密度从5.1%降至2.2%,并得到峰形良好的信号峰。该进样系统的试样消耗小、灵敏度和检出限均优于常规进样系统。10次测定10 μg/L的Pt标准溶液和血清样品溶液,峰高的RSD分别为2.9%和3.3%。该进样系统测得10个血清中的Pt含量与常规进样系统的测试结果无显著差异,在样品量稀少的情况下具有良好的应用价值。     

Flow injection calibration techniques

Summary The role of calibration in the overall analytical procedure is discussed and the potential role of flow injection techniques are assessed. The factors affecting the dispersion obtained in a flow injection system are described and examples given of how control of the various factors can be exploited to produce manifolds for calibration purposes. Most of these examples concern atomic spectrometry methods for which there is considerable interest at present in developing extended range calibrations and flow injection versions of the standard additions method. Several examples of the latter are given.

---

Anwendung der Fließinjektions-Technik für Eichmethoden

     

Flow injection and microwave-oven sample decomposition for determination of copper,zinc and iron in whole blood by atomic absorption spectrometry

A simple and rapid method is proposed for the determination of copper, zinc and iron in whole blood. The injected sample is mineralized in the flow system on passage through a microwve oven and the metals are determined by atomic absorption spectrometry. Prior sample destruction or removal of organic material prior to injection is not necessary. The required volumes for each analysis are 90, 60 and 100 μl for copper, zinc and iron, respectively. The relative standard deviations were less than 3% in all cases. There was good agreement between the results obtained with the flow-injection method and those attained by conventional spectrophotometric measurements.     

Determination of trace amounts of cadmium, lead, copper and zinc in natural waters by inductively coupled plasma atomic emission spectrometry with thermospray nebulisation, after enrichment on Chelex-100

Enrichment on Chelex-100, followed by evaporation when necessary, was used for the pre-concentration of Cd, Pb, Cu and Zn from natural waters. The measurements were carried out with inductively coupled plasma atomic emission spectrometry using a thermospray nebulisation system to reach the required sensitivity. The detection limits corresponding to three times the standard deviation of the blank (in 1% v/v HNO3) after a 30-fold enrichment are 0.02 microgram l-1 for Cd, 0.33 microgram l-1 for Pb and 0.03 microgram l-1 for Cu and Zn. Matrix effects, which are fairly serious with thermospray nebulisation, were taken into account by using the standard additions method. Results obtained for several river water samples were compared with those found by analysis of the non-enriched sample with inductively coupled plasma mass spectrometry or graphite furnace atomic absorption spectrometry. In all instances the agreement was satisfactory.     

Flow injection systems with inductively-coupled argon plasma atomic emission spectrometry : Part 1. Fundamental Considerations

Flow injection systems with inductively-coupled argon plasma atomic emission spectromeiry are proposed. Effects of flow rates, injected volumes and mixing Coil lengths are investigated and conditions for the measurement of the flow injection transient signal are discussed. The peak profile measured with the spectrometer corresponds well with the estimate of the true sample zone distribution near the inlet of the spectrometer made by a zone-sampling process; thus the plasma is not a limiting factor in the proposed systems. For plant analysis, the system provides nearly zero sample dispersion and so the inherent sensitivity of the spectrometric method is preserved. The results obtained for 10 elements in the NBS Orchard Leaves reference material (SRM 1571) are in good agreement with the certified values. For determinations of calcium and magnesium in dolomitic limestones, cadmium is used as internal standard and so the merging zones configuration is employed. The proposed system provides medium sample dispersion and permits about 100 samples to be analysed per hour. Relative standard deviations of 1.34% and 1.23% were calculated for the calcium and magnesium data, respectively. The analytical results compare favorably with those obtained by normal i.c.p. spectrometry with pneumatic sample aspiration, after manual sample dilution.     

Flow injection method for the rapid determination of chemical oxygen demand based on microwave digestion and chromium speciation in flame atomic absorption spectrometry

The present paper describes a new flow injection method for the determination of Chemical Oxygen Demand (COD). This method consists of a first digestion step, where the sample is heated by microwave radiation, a second one where an anionic exchange resin retains the Cr(VI) that has not been reduced by the organic matter of the sample and a third one where Cr(VI), after being eluted, is determined by flame atomic absorption spectrometry. The microwave power applied, the sulphuric acid concentration, the liquid flow in the digestion step and the sample volume were the variables studied. The recovery and precision obtained with this method are similar to those obtained using a standard semi-micro method, whereas the throughput is much higher (up to 50 determinations per hour). As regards sensitivity, by changing the sample loop volume and the concentration of dichromate, one can analyze samples with Chemical Oxygen Demand values between 25 and 5000 mg/l. The limit of detection is about 7 mg/l COD. An interesting feature of the new method, which is not shared by most other flow injection methods of Chemical Oxygen Demand determination, is that there is no matrix effect in the determination step.     

Determination of zinc and cadmium in small amounts of biological tissues by microwave- assisted digestion and flow injection atomic absorption spectrometry

A microwave oven/flow injection/amotic absorption spectrometric system that permits the determination of zinc and cadmium in small samples of human kidney and liver tissue (ca. 1 g) is described. Digested samples are pumped to a closed flow circuit from which aliquots (20 λ for Zn and 100 μl for Cd) are injected for atomic absorption spectrometry. Precision (ca. 2–6% RSD) and recovery (97–103% for Zn and 96–98% for Cd) are good. Accuracy is confirmed by standard additions and use of standard reference materials. Data obtained for male and female human liver and kidney samples are presented.     

Sequential injections in flow system as an alternative to gradient exploitation

In flow injection analysis, several plugs can be injected simultaneously into the same carrier system, in order to achieve overlapped zones. The potentialities of such sequential injections are studied in model systems with spectrophotometric detection; the procedure is shown to give better precision than the use of concentration gradients. The method is used with atomic absorption spectrometry to allow the determination of a wide range of manganese contents in rocks, and to facilitate the use of standard additions for the determination of copper in ethanol.     

Sequential injection analysis implementing multiple standard additions for As speciation by liquid chromatography and atomic fluorescence spectrometry (SIA-HPLC-AFS)

An analytical procedure for multiple standard additions of arsenic species using sequential injection analysis (SIA) is proposed for their quantification in seafood extracts. SIA presented flexibility for generating multiple specie standards at the ng mL⁻¹ concentration level by adding different volumes of As(III), As(V), monomethylarsonic (MMA) and dimethylarsinic (DMA) to the sample. The mixed sample plus standard solutions were delivered from SIA to fill the HPLC injection loop. Subsequently, As species were separated by HPLC and analyzed by atomic fluorescence spectrometry (AFS). The proposed system comprised two independently controlled modules, with the HPLC loop acting as the intermediary device. The analytical frequency was enhanced by combining the actions of both modules. While the added sample was flowing through the chromatographic column towards the detection system, the SIA program started performing the standard additions to another sample. The proposed method was applied to spoiled seafood extracts. Detection limits based on 3σ for As(III), As(V), MMA and DMA were 0.023, 0.39, 0.45 and 1.0 ng mL⁻¹, respectively.     

Determination of lead in fly-ash from a garbage incinerator by atomic-absorption and x-ray fluorescence spectrometry

The lead content in fly-ash collected by an electrostatic precipitator has been determined by atomic-absorption spectrometry (AAS) after decomposition by four different leaching/dissolution techniques, and also determined by X-ray fluorescence spectrometry (XRFS) by the standard-addition method. The XRFS data were evaluated by non-linear regression since the standard additions affected the attenuation coefficient of the sample. Good agreement was obtained between the results obtained with AAS and XRFS. It is concluded that lead is quantitatively extracted by hot 1M nitric acid or treatment with hydrofluoric acid/nitric acid. Direct measurement of briquetted samples by XRFS is suggested for rapid monitoring of the lead content in fly-ash from garbage incineration.     

Non-dispersive atomic-fluorescence spectrometry of trace amounts of bismuth by introduction of its gaseous hydride into a premixed argon (entrained air)-hydrogen flame

A method has been developed for the determination of bismuth by generation of its gaseous hydride and introduction of the hydride into a premixed argon (entrained air)-hydrogen flame, the atomic-fluorescence lines from which are all detected by use of a non-dispersive system. The detection limit is 5 pg/ml, or 0.1 ng of bismuth, but the reagent blank found in a 20-ml sample volume was approximately 2 ng of bismuth. Analytical working curves obtained by measuring peak-heights and integrated peak-areas of the signals are linear over a range of about four orders of magnitude from the detection limit. Perchloric, phosphoric and sulphuric acids up to 2.0M concentration give no interference, but nitric acid gives slight depression of the signal. The presence of silver, gold, nickel, palladium, platinum, selenium and tellurium in 1000-fold ratio to bismuth causes pronounced depression of the signal, whereas mercury and tin slightly enhance the atomic-fluorescence signal. The method has been applied to the determination of bismuth in aluminium-base alloys and sulphide ores with use of the standard additions method. The results are in good agreement with those obtained by flame atomic-absorption spectrometry and optical emission spectrometry with an inductively coupled plasma.     

Rapid determination of corticosteroids in pharmaceuticals by flow injection analysis

The proposed method is based on the reduction of blue tetrazolium by the steroid in an alkaline medium to form a highly colored formazan. The effects of reagent concentration, temperature, flow rate, and manifold design on the reaction are discussed for a typical steroid, methylprednisolone acetate. Analytical readout is obtained within 30 s after sample introduction and up to 100 samples/h can be processed with baseline resolution between peaks. Typical relative standard deviations of 0.5% are obtained with 10-μ1 injection volumes. Results obtained by flow injection analysis are similar to those obtained with the AutoAnalyzer technique.     

Elemental analysis of silicon based minerals by ultrasonic slurry sampling electrothermal vaporisation ICP-MS

Ultrasonic slurry sampling electrothermal vaporisation inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) was applied to the elemental analysis of silicate based minerals, such as talc or quartz, without any pre-treatment except the grinding of the sample. The electrothermal vaporisation device consists of a tungsten coil connected to a home-made power supply. The voltage program, carrier gas flow rate and sonication time were optimised in order to obtain the best sensitivity for elements determined. The relationship between the amount of sample in the slurry and the signal intensity was also evaluated. Unfortunately, in all cases, quantification had to be carried out by the standard additions method owing to the strong matrix interferences. The global precision of the proposed method was always better than 12%. The limits of detection, calculated as three times the standard deviation of the blank value divided by the slope of the calibration curve, were between 0.5 ng/g for As and 3.5 ng/g for Ba. The method was validated by comparing the concentrations found for Cu, Mn, Cr, V, Li, Pb, Sn, Mg, U, Ba, Sr, Zn, Sb, Rb and Ce using the proposed methodology with those obtained by conventional nebulisation ICP-MS after acid digestion of the samples in a microwave oven. The concentration range in the solid samples was between 0.2 μg/g for Cr and 60 μg/g for Ba. All results were statistically in agreement with those found by conventional nebulisation.     

Direct injection LC/ESI-MS horse urine analysis for the quantification and identification of threshold substances for doping control. I. Determination of hydrocortisone

Two simple and rapid LC/MS methods with direct injection analysis were developed and validated for the quantification and identification of hydrocortisone in equine urine using the same sample preparation but different mass spectrometric systems: ion trap mass spectrometry (IT-MS) and time-of-flight mass spectrometry (TOF-MS). The main advantage of the proposed methodology is the minimal sample preparation procedure, as particle-free diluted urine samples were directly injected into both LC/MS systems. Desonide was used as internal standard (IS). The linear range was 0.25-2.5 microg ml(-1) for both methods. Matrix effects were evaluated by preparing and analyzing calibration curves in water solutions and different horse urine samples. A great variation of the signal both for hydrocortisone and the internal standard was observed in different matrices. To overcome matrix effects, the unavailability of blank matrix and the excessive cost of the isotopically labeled internal standard, standard additions calibration method was applied. This work is an exploration of the performance of the standard additions approach in a method where neither nonisotopic internal standards nor extensive sample preparation is utilized and no blank matrix is available. The relative standard deviations of intra and interday analysis of hydrocortisone in horse urine were lower than 10.2 and 5.4%, respectively, for the LC/IT-MS method and lower than 8.4 and 4.4%, respectively, for the LC/TOF-MS method. Accuracy (bias percentage) was less than 9.7% for both methods. Copyright (c) 2008 John Wiley & Sons, Ltd.     

Immobilization of 8-hydroxyquinoline onto silicone tubing for the determination of trace elements in seawater using flow injection ICP-MS

A rapid and simple on-line method is described for the preconcentration of Mn, Co, Ni, Cu, Zn, Cd and Pb from sea water using 8-hydroxyquinoline immobilized onto silicone tubing (Sil-8-HQ) via the Mannich reaction. Recoveries between 35 and 95% and limits of detection in the ppt range were obtained using a 2 m long Sil-8-HQ tube with a sample flow rate of 1.0 ml min(-1). A tube could be subjected to sample loading and elution cycles over 200 times. The capacity was 1.5 and 1.3 mug cm(-2) for Cu and Mn, respectively. Cu, Cd, Co, Pb, Mn, Zn and Ni were determined in coastal and open ocean seawater using flow injection inductively coupled plasma mass spectrometry (FI-ICP-MS). Good agreement with certified values for the certified reference materials NASS-4 and CASS-3 was demonstrated when quantitation was undertaken by the method of additions.     

Interference-free determination of trace levels of gold and palladium in geological and metallurgical samples by flame atomic absorption spectrometry coupled with a flow injection on-line microcolumn preconcentration and separation system

A simple and highly selective method was developed for the routine determination of trace or ultratrace amounts of gold and palladium in geological and metallurgical samples. The method uses flow injection on-line preconcentration and separation with determination by flame atomic absorption spectrometry. Au and Pd in the sample are adsorbed on a 2-mercaptopyrimidine chemically modified silica gel (MPMSG) packed microcolumn in a 0.50M HCl medium and then eluted with 0.5 or 1.0% thiourea solution. The eluates are introduced into the flame atomic absorption spectrometer directly. With the use of a 0.85 mL microcolumn (about 0.14 g MPMSG packed), the present system tolerated concentrations of common base metal ions up to 25.0 mg/mL and concentrations of anions up to 100.0 mg/mL when Au(III) at 0.100 microg/mL and Pd(II) at 0.200 microg/mL were preconcentrated for 60 s with a sample flow rate of 5.0 mL/min. The limits of detection were 3.1 ng/mL for Au(III) and 6.1 ng/mL for Pd(II) with relative standard deviations of < or = 2.5%. The analytical results obtained by the proposed method for geological and metallurgical samples were in good agreement with the certified values.     

Multisyringe flow injection system for total inorganic selenium determination by hydride generation-atomic fluorescence spectrometry

A new multisyringe flow injection system for total inorganic selenium determination by hydride generation-atomic fluorescence spectrometry (HGAFS) has been proposed. The flow methodology is based on the simultaneous injection of sample in the acid media (50% HCl), a reducing sodium tetrahydroborate solution (0.18%) and a solution of hydrochloric acid (50%) which are dispensed into a gas-liquid separation cell by using a multisyringe burette coupled with one multiport selection valve. The usage of the time-based injection increases the sample throughput and provides precise known volumes of sample. The hydride of selenium is delivered into the flame of an atomic fluorescence spectrometer by means of an argon flow. A hydrogen flow has been used to support the flame.The technique can be applied over a wide range of concentrations of selenium between 0.1 and 3.5 μg l⁻¹ with good repeatability (relative standard deviation (R.S.D.) values 4.6-7% for 1 μg l⁻¹ of Se). The detection limit of the developed technique (3σ_b/S) was 0.01 μg l⁻¹. A sample throughput was 28 samples per hour (84 injections). The multisyringe technique has been validated by means of reference solid (sea lettuce) and water (hard drinking water) materials with good agreement with certified values. The analytical features were compared with those obtained by using of the commercial flow injection analysis (FIA) system. The proposed method provides a higher sampling frequency and a significant reduction of reagent and sample consumption in front the flow injection application.     

Determination of zinc in pharmaceutical products using an electrodialyser incorporated into a flow system

An electrodialyser unit has been designed, incorporated into the conduits of a flow injection (FI) system, and employed for the removal of interferences in the determination of zinc(II) in multivitamin tablets. The proposed system is fully computerised and is able to determine zinc(II) at a frequency of 18 samples/h with a sample interaction of 0.0015%. The calibration graph is linear between 1 and 20 mg/L. The detection limit is 0.998 mg/L. The results obtained for zinc(II) in multivitamin tablets with the proposed system compared favourably with those obtained with the standard manual AAS method.     

Turbidimetric determination of sulphate in plant digests and natural waters by flow injection analysis with alternating streams

An improved flow injection system with alternating streams of reagents is described for the turbidimetric determination of sulphate. Samples are injected into an inert carrier stream which is mixed with barium chloride to form a barium sulphate suspension. The range of the method can be extended to low concentrations by continuously adding sulphate to the sample carrier stream. System performance is improved by automatic alternate pumping of the reagent stream and an alkaline EDTA solution at high flow rate. All operations are controlled by an electronically-operated proportional injector-commutator. Even after routine analysis of 3000 samples of natural waters and plant digests, baseline drift was not observed. The proposed method is suitable for 120 samples per hour with a relative standard deviation less than 1% for sulphate concentrations in the range 1–30 ppm (waters) or 5–200 ppm (plant digests). The results compare well with those obtained by standard manual procedures.     

On-line ion-exchange separation and determination of niobium,tantalum, tungsten,zirconium and hafnium in high-purity iron by flow injection inductively coupled plasma mass spectrometry

A study was made to investigate the feasibility of using an anion-exchange resin for on-line separation of trace amounts of niobium, tantalum, tungsten, zirconium and hafnium from iron matrix samples. The incorporation of a micro-column packed with Dowex 1X8-100 ion-exchange resin into a flow injection system is presented. The detection was done with inductively coupled plasma mass spectrometry (ICP-MS). The sample treatment, optimization of analytical variables and measurable concentration levels are discussed. Recoveries from standard additions to a high-purity iron were for all the analytes close to 100%, with relative standard deviations ranging from 0.7 to 3.0%. The limits of quantification (10 s_n−1) calculated from a 5% (m/v) iron sample solution were 8, 5, 14, 12 and 10 ng g⁻¹ for Nb, Ta, W, Zr and Hf, respectively. The accuracy of the proposed method was tested by determining these elements in Euronorm-CRM 098-1 reference material. Recoveries from 0.250 g test portions of the above reference material spiked with 2.5 and with 12.5 ng each of the five analytes are reported.