Instability of the separated shear layer in flow past a cylinder: Forced excitation

The receptivity of the separated shear layer for Re = 300 flow past a cylinder is investigated by forced excitation via an unsteady inflow. In order to isolate the shear layer instability, a numerical experiment is set up that suppresses the primary wake instability. Computations are carried out for one half of the cylinder, in two dimensions. The flow past half a cylinder with steady inflow is found to be stable for Re = 300. However, an inlet flow with pulsatile perturbations, of amplitude 1% of the mean, results in the excitation of the shear layer mode. The frequency of the perturbation of the inlet flow determines the frequency associated with the shear layer vortices. For a certain range of forced frequencies the recirculation region undergoes a low‐frequency longitudinal contraction and expansion. An attempt is made to relate this instability to a global mode of the wake determined from a linear stability analysis. Interestingly, this phenomenon disappears when the outflow boundary of the computational domain is shifted sufficiently downstream. This study demonstrates the need of carefully investigating the effect of the location of outflow boundaries if the computational results indicate the presence of low‐frequency fluctuations. The effect of Re and amplitude of unsteadiness at the inlet are also presented. All computations have been carried out using a stabilized finite element formulation of the incompressible flow equations. Copyright © 2007 John Wiley & Sons, Ltd.     

On separated shear layer of blunt circular cylinder

Separated shear layer of blunt circular cylinder has been experimentally investigated for the Reynolds numbers (based on the diameter) ranging from 2.8×10³ to 1.0×10⁵, with emphasis on evolution of separated shear layer, its structure and distribution of Reynolds shear stress and turbulence kinetic energy. The results demonstrate that laminar separated shear layer experiences 2–3 times vortex merging before it reattaches, and turbulence separated shear layer takes 5–6 times vortex merging. In addition, relationship between dimensionless initial frequencies of K-H instability and Reynolds numbers is identified, and reasons for the decay of turbulence kinetic energy and Reynolds shear stress in reattachment region are discussed. The project supported by the National Natural Science Foundation of China and the Key Laboratory for Hydrodynamics of NDCST.     

Numerical simulation of shear effect on vortex shedding behind a square cylinder

This paper is concerned with the numerical simulation of the flow structure around a square cylinder in a uniform shear flow. The calculations were conducted by solving the unsteady 2D Navier–Stokes equations with a finite difference method. The effect of the shear parameter K of the approaching flow on the vortex-shedding Strouhal number and the force coefficients acting on the square cylinder is investigated in the range K=0·0–0·25 at various Reynolds numbers from 500 to 1500. The computational results are compared with some existing experimental data and previous studies. The effect of shear rate on the Strouhal number and the force acting on the cylinder has a tendency to reduce the oscillation. The Strouhal number, mean drag and amplitude of the fluctuating force tend to decrease as the shear rate increases, but show no significant change at low shear rate. Increasing the Reynolds number decreases the Strouhal number and increases the force acting on the cylinder. At high shear rate the shedding frequencies of the fluctuating drag and lift coefficients are identical. © 1997 John Wiley & Sons, Ltd.     

Underlay mechanism in lift-drag phase diagrams for shear flow over cylinder

The characteristics of a uniform-shear flow over a circular cylinder are in- vestigated numerically by using the alternative-direction implicit （ADI） algorithm and a fast Fourier transform （FFT） one in the exponential-polar coordinates for Re = 150 and 0 ≤ K ≤ 0.46. The diagram of lift-drag phase, implying the detail information about the fluctuations of drag and lift as well as the flow patterns in the wake and fluctuating pres- sure on the cylinder surface, is used to describe the effects of the shear rate on the flow. Results show that the upper （or lower） closed curve of a phase diagram corresponds to the first （or second） half shedding cycle. The lift-drag phase diagram will move down-left with the increase of shear rate K such that the lift is exerted from the upper side to the lower side, and the drag on the first half shedding cycle is smaller than that on the second half.     

Flow past a transversely oscillating square cylinder in free stream at low Reynolds numbers

This paper reports simulation results for free‐stream flow past an oscillating square cylinder at Re=100 and 150, for oscillating‐to‐natural‐shedding frequency ratios of 0.5?f_r?3.0 at a fixed oscillation amplitude of 0.2 of the cylinder width. The transformed governing equations are solved in a non‐inertial frame of reference using the finite volume technique. The ‘lock‐in’ phenomena, where the vortex shedding becomes one with the oscillation frequency, is observed near the natural shedding frequency (f_r≈1). Beyond the synchronization band, downstream recovery of the wake to its stationary (natural) state (frequency) is observed in cross‐stream velocity spectra. At higher forcing frequencies, a phase lag between the immediate and the far wake results in a shear layer having multi‐polar vortices. A ‘Vortex‐switch’ accompanied by a change in the direction of energy transfer is identified at the ‘lock‐in’ boundaries. The variation of aerodynamic forces is noticed to be different in the lock‐in regime. The velocity phase portrait in the far wake revealed a chaotic state of flow at higher excitation though a single (natural) frequency appears in the spectra. Copyright © 2008 John Wiley & Sons, Ltd.     

Centrifugal instability and the rib vortices in the cylinder wake

The physical mechanism for generation of streamwise vortices (or rib vortices) in the cylinder wake is numerically investigated with a finite-difference scheme. Rayleigh's theory of centrifugal instability for inviscid axisymmetric flow is extended to analyze the 2-D primary flows. Accordingly, an analytical dimensionless groupRay=−(r/v _θ)∂v _θ/∂r−1 is derived, wherev _θ represents the velocity of a fluid element relative to the oncoming flow,r is the local curvature radius of the element pathline. Centrifugal instability occurs whenRay>0. Stability analyses are carried out with this discriminant for primary flows at different time levels in a half shedding period of the von Kármán (or vK) vortices. Unstable areas are identified and the locations of rib vortices are coincident well with the unstable areas within the first wavelength of vK vortices behind the cylinder. The numerical results also show that rib vortices experience amplification in this region. It is apparent that centrifugal instability plays an important role in the generation of rib vortices in the cylinder wake. The project spported by the National Natural Science Foundation of China     

Shear layer instability and acoustic interaction in solid propellant rocket motors

Segmentation of solid propellant rocket motors has been demonstrated to be a source of unpredicted and undesirable pressure and thrust oscillations. Surface discontinuities are the primary cause of these vortex-shedding-driven oscillations, which result from a strong coupling between the shear layer instability and the acoustic motion in the chamber. The analysis of an axisymmetric geometry corresponding to a {1\over 15} subscale P230 motor of the Ariane 5 rocket is numerically computed. With a suitable mesh for the viscosity value studied, the aeroacoustics in the chamber is fully described. A coupling between the hydrodynamic instability and the organ-pipe acoustic mode is clearly demonstrated. The mechanism for frequency selection is discussed. © 1997 John Wiley & Sons, Ltd.     

Control of vortex shedding behind circular cylinder for flows at low Reynolds numbers

It has been observed by researchers in the past that vortex shedding behind circular cylinders can be altered, and in some cases suppressed, over a limited range of Reynolds numbers by proper placement of a second, much smaller, ‘control’ cylinder in the near wake of the main cylinder. Results are presented for numerical computations of some such situations. A stabilized finite element method is employed to solve the incompressible Navier–Stokes equations in the primitive variables formulation. At low Reynolds numbers, for certain relative positions of the main and control cylinder, the vortex shedding from the main cylinder is completely suppressed. Excellent agreement is observed between the present computations and experimental findings of other researchers. In an effort to explain the mechanism of control of vortex shedding, the streamwise variation of the pressure coefficient close to the shear layer of the main cylinder is compared for various cases, with and without the control cylinder. In the cases where the vortex shedding is suppressed, it is observed that the control cylinder provides a local favorable pressure gradient in the wake region, thereby stabilizing the shear layer locally. Copyright © 2001 John Wiley & Sons, Ltd.     

不同剪切率来流作用下柔性圆柱涡激振动数值模拟

采用浸入边界法对细长柔性圆柱在线性剪切流条件下的涡激振动进行三维数值模拟。细长柔性圆柱振动采用三维索模型模拟,其两端铰接,质量比为6,长细比为50,无量纲顶张力为496。来流为线性剪切流,剪切率从0到0.024变化,最大雷诺数为250。研究发现:剪切流作用下柔性立管横流向振动表现为驻波模式,而顺流向振动表现为行波-驻波混合模式。随着剪切率增大,振动频谱呈现多频响应,振动能量逐渐向低频转移。阻力系数平均值随着展向变化,脉动阻力系数和升力系数的均方根值均表现为“双峰”模式。流固能量传递系数沿立管轴向的分布表明,振动激励区集中于高流速区,而振动阻尼区多位于低流速区。剪切率较小时,圆柱的泻涡为平行交叉模式;剪切率较大时,圆柱的泻涡为倾斜泻涡模式,且由于泻涡频率沿立管轴向变化,尾流发生涡裂现象,形成泻涡频率不同的胞格结构。      

Vortex shedding from a circular cylinder with a slit and concave rear surface

Vortex shedding from short circular cylinders with a slit was studied using a flow visualization and amplitude spectrum analysis of a thermoanemometry probe signal. It was found that a circular cylinder with a slit and concave rear surface produces stronger vortices than other bluff cylinders but that these vortices are very vulnerable to the end wall conditions. It was established that two small splitter plates (tails) fixed directly behind the cylinder at the end walls effectively isolate the vortices shed from the cylinder from the end wall boundary layer effects. For this arrangement a perfect regularity of vortex shedding and almost constant Strouhal number were achieved in the Reynolds number test range of about 250 to 43,000.On a leave from Technical University, 60965 Poznan, Piotrowo 3, Poland.     

Analysis on secondary instability of shear layer based on the concept of phase synchronization

A concept of phase synchronization point is proposed, and then a model is built using this concept to explain secondary instabilities. This model has been used to determine the conditions of K- and H-type secondary instabilities, which are coincident with the conditions published in literatures. It also can be used to analyze other secondary instability phenomena. For example, the numerical results validate the analysis results in the case of 1/3rd subharmonic mode secondary instability. Furthermore, the numerical results indicate that the spanwise wave number of 3D disturbance has significant effect on the secondary instability.     

Stability of flow past a cylinder: Energy budget of eigenmodes

Global linear stability analysis of the flow past a circular cylinder at the onset of primary wake instability is carried out. The real and imaginary parts of the most unstable eigenmode, responsible for vortex shedding, are very similar but associated with a spatial shift in the vortex structures. This shift results in the convection of vortices that are observed in the unsteady flow, which is actually a consequence of global absolute instability. The kinetic energy density, associated with the most unstable eigenmode, is studied. At the onset of the instability the energy density of the disturbance field is found to be stronger in the far wake compared with the near wake. With increase in Re the region where the disturbance is strong moves upstream closer to the cylinder. However, the maximum value of the kinetic energy density of the disturbance lies outside the recirculation zone even for Re upto 100. A linearized mechanical energy equation for the time evolution of the kinetic energy density of the disturbance is utilized to examine the energy budget of the most unstable eigenmode at various Re. It is found that the most significant contribution to the growth rate of the disturbance arises from the transfer of the energy due to the strain rate of the base flow to the perturbation. The stabilizing effect of the viscous dissipation increases with increase in Re, but saturates for Re beyond ～70. Copyright © 2009 John Wiley & Sons, Ltd.     

Flow past a sphere in density-stratified fluid

Stratified flow past a three-dimensional obstacle such as a sphere has been a long-lasting subject of geophysical, environmental and engineering fluid dynamics. In order to investigate the effect of the stratification on the near wake, in particular, the unsteady vortex formation behind a sphere, numerical simulations of stratified flows past a sphere are conducted. The time-dependent Navier–Stokes equations are solved using a three-dimensional finite element method and a modified explicit time integration scheme. Laminar flow regime is considered, and linear stratification of density is assumed under Boussinesq approximation. The effects of stratification is implemented by density transport without diffusion. The computed results include the characteristics of the near wake as well as the effects of stratification on the separation angle. Under increased stratification, the separation on the sphere is suppressed and the wake structure behind the sphere becomes planar, resembling that behind a vertical cylinder. With further increase in stratification, the wake becomes unsteady, and consists of planar vortex shedding similar to von Karman vortex streets.     

On the development of lift and drag in a rotating and translating cylinder

The two-dimensional flow around a rotating cylinder is investigated numerically using a vorticity forces formulation with the aim of analyzing quantitatively the flow structures, and their evolutions, that contribute to the lift and drag forces on the cylinder. The Reynolds number considered, based on the cylinder diameter and steady free stream speed, is Re=200, while the non-dimensional rotation rate (ratio of the surface speed and free stream speed) selected was α=1 and 3. For α=1 the wake behind the cylinder for the fully developed flow is oscillatory due to vortex shedding, and so are the lift and drag forces. For α=3 the fully developed flow is steady with constant (high) lift and (low) drag. Each of these cases is considered in two different transient problems, one with angular acceleration of the cylinder and constant speed, and the other one with translating acceleration of the cylinder and constant rotation. We characterize quantitatively the contributions of individual fluid elements (vortices) to aerodynamic forces, explaining and quantifying the mechanisms by which the lift is generated in each case. In particular, for high rotation (when α=3), we explain the relation between the mechanisms of vortex shedding suppression and those by which the lift is enhanced and the drag is almost suppressed when the fully developed flow is reached.     

Numerical modelling of confined flow past a cylinder of square cross-section at various orientations

Results are presented for the unsteady, two-dimensional flow and heat transfer due to a square obstruction of diameter d located asymmetrically between the parallel sliding walls of a channel with length-to-height ratio W/H = 6·44. Analysis is based on the numerical solution of spatially and temporally second-order accurate finite difference approximations of the transport equations expressed in curvilinear co-ordinates. Laminar, constant property flow is assumed for obstruction configurations in which the blockage ratio is d/H = 0·192, the nearest-wall distances are g/d = 0·2, 0·5 and 1, the orientation angles are α=0°, 10° and 20° and the Reynolds numbers are Re=100, 500, and 1000. Preparatory testing of the numerical procedure was performed for a variety of documented flows to verify its physiconumerical accuracy and obtain estimates of the residual grid-dependent uncertainties in the variables calculated. Heat transfer, drag and lift coefficients and Strouhal numbers for the present flow were finally calculated to within 4%–7% of their grid-dependent values using non-uniformly spaced grids consisting of (x=99, y=55) nodes. Above a critical value of the Reynolds number, which depends on the geometrical parameters, the flow is characterized by alternate vortex shedding from the obstruction top and bottom surfaces. Streamline, vorticity and particle streakline plots provide qualitative impressions of the unsteady vortical flow. Especially noteworthy are the extremes in the lift coefficient which ranges from large positive values for an obstruction with g/d=0·2 and α=10° to negative values for one with g/d=0·5 and α=0°. Both the drag and lift coefficients as well as the Strouhal number exhibit non-monotonic variations with respect to the parameters explored. Asymmetries in the obstruction location and orientation account for relatively large vortex-induced periodic variations in heat transfer, especially along the wall nearest the obstruction. Notable differences are also predicted for the heat transfer coefficients of the individual obstruction surfaces as a function of the orientation angle.