The effect of various diallyl (diallyl ortho phthalate, diallyl terephthalate and diethylene glycol diallyl carbonate) and triallyl monomers (triallyl cyanurate and triallyl isocyanurate) on the processability of polyphenylene oxide (PPO) was studied. The solubility parameters of the monomers indicated that diallyl orthophalate, dially terephthalate and triallyl cyanurate should be miscible with PPO suggesting their applicability as reactive plasticizers to improve the processability of PPO. Rheological studies of 60:40 wt:wt PPO:allylic blends indicate that the addition of 40 wt% of allylic monomers significantly improved processability – blends of 60PPO:40DEGDAC indicates the highest viscosity and the highest Tg. Rheological studies and dynamic mechanical analysis on various PPO/DAOP blends show that the increasing amounts of DAOP progressively decreases the viscosity and Tg of the blends. Phase separation at room temperature was observed by visual opacity, cloud point studies and DMTA in PPO:DAOP blends with less than 60 wt% PPO but at elevated temperatures the blends were miscible. 相似文献
Abstract Polyester elastomer (PEL) blends having a hard segment of polyester (PBT), soft segment of polyether (PTMG), and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate) were prepared with a twin-screw extruder. Test specimens for thermal properties were prepared by injection molding. Rheological properties and morphology were investigated by Instron capillary rheometer (ICR) and scanning electron microscopy (SEM). Thermal properties of the LCP/PEL blends were investigated by DSC, dilatometer, heat deflection temperature tester, and a Rheovibron viscometer. DSC study revealed a partial miscibility between LCP and PEL. It was found that the LCP acted as a nucleating agent for the crystallization of PEL in the LCP/PEL blends. The dimensional and thermal stability of the blends were increased by increasing the LCP cont-ent. The storage modulus (E' was improved by increasing the LCP content. The blend viscosity showed a minimum value at 5 wt% of LCP which increased by increasing the LCP content above 5 wt% of LCP The morphology of the LCP/PEL blends showed poor interfacial adhesion between the two phases, and the fibrillar structure of LCP phase in the matrix was affected by the LCP content, shear rate, and extrusion temperature. The morphology of the blends was found to be affected by their compositions and processing conditions. 相似文献
α, β-Bis(hydroxyphenol) tetramethyl bisphenol-A polysulfone (PSUT) was synthesized by two different methods, one using a strong base, the other using a weak base. The bifunctional polysulfone containing tetramethyl bisphenol-A chain ends was exploited as a model telechelic that can be used for the preparation of ABA triblock copolymers containing poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) as A segments and PSUT as B segments. PSUT and PPO were incorporated into triblock copolymers by an oxidative coupling copolymerization of PSUT with 2,6-dimethylphenol or by the redistribution of PPO in the presence of PSUT. The mechanism of block copolymerization is discussed. DSC studies indicate that short immiscible PPO and PSUT segments incorporated into a triblock copolymer do not exhibit phase separation. Polymer blends of the PPO–PSUT–PPO triblock copolymers with PPO homopolymer were analyzed by DSC. Both miscible and phase-separated blends can be prepared depending on the molecular weight of both PPO homopolymer and of the PPO segment present in the triblock copolymer. Polymer blends of the PPO–PSUT–PPO triblock copolymer with PSUT were miscible at all compositions. 相似文献
Summary: The present communication reports the first use of electron tomography in reconstructing the three‐dimensional morphology in thermoplastic elastomer blends. The blends investigated were dynamically vulcanized blends of ethylene‐propylene‐diene (EPDM) rubber/poly(propylene)/oil and polystyrene‐block‐(ethylene‐co‐butylene)‐block‐polystyrene (SEBS)/poly(propylene)/oil. An easy identification of blend morphology could be carried out at blend compositions, where conventional transmission electron microscopic imaging gives misleading information. This technique gives a higher resolution than any other microscopic technique, and is applicable to blends with dispersed as well as co‐continuous morphologies.
Example of a tomographic model of partially co‐continuous SEBS phases in a SEBS/PP/oil thermoplastic blend. Only the contours of the SEBS phase are shown. 相似文献
Primary amine terminated polystyrene (PS-NH2), with Mn=12,000 g/mol and Mw=23,000 g/mol, was applied as a reactive compatibilizer for poly(styrene-co-maleic anhydride)/poly(phenylene oxide) (SMA/PPO) blends, in which both an impact modifier for the continuous SMA phase, viz. ABS, and the dispersed PPO phase, viz. SEBS, was incorporated. During melt blending, SMA-g-PS copolymers are generated at the interface between the SMA/ABS and the PPO/SEBS phases. The addition of 10 wt % of the reactive PS-NH2 compatibilizer to a SMA/ABS/PPO/SEBS 30/30/30/10 blend results in a more significant refinement of the dispersed PPO/SEBS particles than 10 wt % of a commercially available, bulky PS-graft-PMMA copolymer with Mn=45,300 and Mw=293,400 g/mol. In addition, PS-NH2 gives a more pronounced enhancement of the yield stress, the stress at break and the notched Izod Impact than the PS-g-PMMA. On the other hand, the elongation at break is higher in the case of the non-reactive PS-g-PMMA. It was demonstrated that surface imperfections, probably introduced by an observed strongly elastic character due to partial crosslinking of the SMA/ABS phase by difunctional H2N-PS-NH2, are responsible for the lower elongation at break for the PS-NH2 based blends. 相似文献