Effect of K-doping on structural and optical properties of ZnO thin films

In this work, K-doped ZnO thin films were prepared by a sol–gel method on Si(111) and glass substrates. The effect of different K-doping concentrations on structural and optical properties of the ZnO thin films was studied. The results showed that the 1 at.% K-doped ZnO thin film had the best crystallization quality and the strongest ultraviolet emission ability. When the concentration of K was above 1 at.%, the crystallization quality and ultraviolet emission ability dropped. For the K-doped ZnO thin films, there was not only ultraviolet emission, but also a blue emission signal in their photoluminescent spectra. The blue emission might be connected with K impurity or/and the intrinsic defects (Zn interstitial and Zn vacancy) of the ZnO thin films.     

Effect of post annealing temperature on structural and optical properties of ZnCdO thin films deposited by sol–gel method

Ternary ZnCdO thin films oriented along c-axis have been successfully deposited on p-Si (1 0 0) substrates using sol–gel spin coating route. To optimize most suitable annealing temperature for the Zn_1−xCd_xO thin films; these films with selected cadmium content x = 0.10 were treated at annealing temperatures from 300 °C up to 800 °C in oxygen ambient after deposition. The structural and optical properties of deposited thin films have been characterized by X-ray diffraction, energy dispersive spectroscopy, atomic force microscopy, UV–Vis spectroscopy, and photoluminescence spectra. The results show that the obtained films possess high crystallinity with wurtzite structure. The crystallite size, lattice parameters, lattice strain and stress in the deposited films are determined from X-ray diffraction analysis. The band gap energy increased as a function of annealing temperatures as observed from optical reflectance spectra of samples. The presence of Cd in the deposited films is confirmed by energy dispersive spectrum and it is observed that Cd re-evaporate from the lattice with annealing. The photoluminescence measurements as performed at room temperature did not exhibit any luminescence related to oxygen vacancies defects for lower annealing temperatures, as normally displayed by ZnO films. The green yellow luminescence associated to these defects was observed at higher annealing temperatures (≥700 °C).     

Synthesis,magnetic properties and microstructure of Ni–Zn ferrite by sol–gel technique

In the study, the Ni–Zn ferrite powder of a Ni_0.3Zn_0.7Fe₂O₄ composition was synthesized by sol–gel route using metal acetates at low temperatures. Both the scanning electron microscope and X-ray diffraction analyses of various gel samples heated at different temperatures were used to identify the reaction stages where the amorphous-gel-to-crystalline phase transition occurred. The electrical, magnetic and microstructural properties of the toroidal cores were studied. It was found that the initial permeability increased with a large frequency band (0.1–31.39 MHz) and the magnetic loss was small. The electrical resistivity was higher as compared to the ones which were obtained by the conventional process. Therefore, well–defined polycrystalline microstructure nickel–zinc ferrite and a short processing time of gel preparation have become the major achievements of this study.     

Microstructural, optical and electrical studies on sol gel derived ZnO and ZnO:Al films

ZnO and ZnO:Al films were deposited onto glass substrates by the sol gel method using spin coating technique. The effects of aluminum dopant on the crystalline structure and orientation of the ZnO films have been investigated by X-ray diffraction (XRD) study. Surface morphology of the films has also been analyzed by a field emission scanning electron microscope (FESEM) and atomic force microscope (AFM). The average optical transmittance values of all the films is over >83% in the visible region. The optical band gap and Urbach energy values of these films were determined. The absorption edge shifted to the lower energy depending on the Al doping level. The shift of absorption edge is associated with shrinkage effect. The electrical conductivity of the ZnO film enhanced with the Al dopant. From the temperature dependence of conductivity measurements, the activation energy of the films was also calculated.     

Structural, optical and electrical properties of cadmium zinc oxide films for light emitting devices

Structural, optical and electrical properties of Cd_yZn_1-yO (y=0–0.1) ternary alloy thin films have been investigated for the films prepared using the spin coating method on the glass substrate. XRD pattern confirmed the nano-size polycrystalline hexagonal wurtzite structure for all the samples. The size of nano-crystals was found to be varied in between 21 and 30 nm. Optical band gap calculated from the absorption coefficient signifies the shift in direct band gap from 3.2 to 2.97 eV with cadmium composition. Through EDAX spectrum, it was confirmed that Cadmium was successfully incorporated into ZnO. SEM studies make clear that even after Cadmium incorporation, the surface morphology of the films remained smooth. The current–voltage characteristics obtained from semiconductor characterization system reveals that resistance of the films was found to be decreased with the increase in cadmium composition. Our investigations lead to the applicability of CdZnO as an active layer in CdZnO/ZnO heterostructure for light emitting devices.     

Effect of solution concentrations on crystal structure,surface topographies and photoluminescence properties of ZnO thin films

Zinc oxide thin films were deposited on silicon substrates via hydrothermal method. Microstructures, surface topographies and optical properties of ZnO thin films were systematically investigated by X-ray diffraction, atomic force microscopy and fluorescence spectrophotometer. The mean grain size and surface roughness of the thin films decrease first and then increase with increasing the concentration of zinc nitrate hexahydrate. The photoluminescence spectra of ZnO thin films, excited by the 240, 320, 360, 380 and 400 nm excitation wavelength, were investigated in detail. Based on our analysis, it can be noted that mechanisms of the ultraviolet, violet and blue emissions are attributed to the transitions from the localized levels below the conduction band, zinc vacancy, interstitial zinc and extended interstitial zinc levels to the valance band, respectively. Blue–violet emissions of ZnO have great potential in light emitting and biological fluorescence labeling applications.     

Effect of Co ions on the microstructure and magnetic properties of nanocrystalline CoxFe3−xO4 films

Co_xFe_3−xO₄ nanocrystalline films (x=0.2-0.8$x=0.2-0.8$) on SiO₂ substrates were prepared by a sol–gel method. The microstructural and magnetic properties of samples were measured by an X-ray diffractometer (XRD) and a vibrating sample magnetometer (VSM), respectively. Atomic force microscopy (AFM) was used to investigate the surface image of the sample. The measurement results of XRD at room temperature show that the pure spinel structure of the film could be obtained at x=0.8$x=0.8$. The magnetic measurements reveal the magnetic properties of the samples depend strongly on Co²⁺ ions content, and the optimal parameters of the saturation magnetization and coercivity in Co_xFe_3−xO₄films are obtained at x=0.8$x=0.8$. Here the coercivity reaches 1.954 kOe. The average grain sizes of the film are less than 30 nm obtained from the microscopy images. The situ measurement at high temperatures of range from 293 to 773 K shows that the microstructures of Co_0.8Fe_2.2O₄ film have good thermal stabilization.     

Effect of Ag doping on the photoluminescence properties of ZnO films

ZnO:Ag films were grown on Si (1 0 0) substrates by ultrasonic spray pyrolysis at various substrate temperatures. The effect of deposition temperature on the structural and the room temperature photoluminescence (RT-PL) properties of ZnO:Ag films was studied. With the deposition temperature rising to 550 °C, the intensity of the near-band edge (NBE) emission at 378 nm decreased and a new emission peak at 399 nm was observed. On the basis of the X-ray diffraction pattern (XRD), the X-ray photoelectron (XPS) spectra of ZnO:Ag films, and the effects of annealing on the PL, we suggest that the 399 nm emission should be attributed to the electron transition from the conduction band to Ag_Zn-related complexes defects radiative centers above the valence band.     

Effect of source temperature on the morphology and photoluminescence properties of ZnO nanostructures

ZnO nanostructures have been synthesized by heating a mixture of ZnO/graphite powders using the thermal evaporation and vapor transport on Si(1 0 0) substrates without any catalyst and at atmospheric argon pressure. The influence of the source temperature on the morphology and luminescence properties of ZnO nanostructures has been investigated. ZnO nanowires, nanoflowres and nanotetrapods have been formed upon the Si(1 0 0) substrates at different source temperatures ranging from 1100 to 1200 °C. Room temperature photoluminescence (PL) spectra showed increase green emission intensity as the source temperature was decreased and ZnO nanowires had the strongest intensity of UV emission compared with other nanostructures. In addition, the growth mechanism of the ZnO nanostructures is discussed based on the reaction conditions.     

Morphology and photoluminescence properties of zinc oxide films grown by pulsed laser deposition

Zinc oxide films with different morphologies have been grown by pulsed laser deposition, varying substrate temperature and oxygen pressure. At low oxygen pressure and low substrate temperature continuous films with different roughness have been obtained, while at high substrate temperature a film with sparse hexagonal pyramids has been observed. Increasing the oxygen pressure the film became rougher and at 100 Pa a rod-array has been deposited. The columns of this rod-array grew along the wurtzite c-axis perpendicularly to the substrate surface as proved by X-ray diffraction measurements. Near to the sample borders the columns were slightly tilted towards the center of the sample. The possible growth mechanisms giving rise to the different morphologies have been discussed. Low-temperature photoluminescence measurements allowed to get information about the film quality, showing the variations of the excitonic peak and two defect bands (green and violet-blue) with the different deposition parameters.     

Properties of Cu and V co-doped ZnO nanoparticles annealed in different atmospheres

Zn_0.97Cu_0.01V_0.02O nanoparticles have been successfully prepared by the sol–gel method and sintered at 600 °C in argon and air atmosphere, respectively. The effects of annealing atmosphere on the structural, optical and magnetic properties of the obtained samples were studied. The X-ray diffraction result showed that the Zn_0.97Cu_0.01V_0.02O was single phase with the wurtzite structure of ZnO. The sample annealed in air had much better crystallization. Photoluminescence shows an increase in green emission when annealing in argon. The two Zn_0.97Cu_0.01V_0.02O samples exhibited ferromagnetism at room temperature. The ferromagnetism in this study was itself property of Cu, V co-doped ZnO and not originated from the secondary phase.     

Investigation of structural and optical properties of ZnO films co-doped with fluorine and indium

Undoped ZnO film and ZnO films, which are co-doped with F and In (FIZO) at different concentrations, were synthesized by sol–gel technique and the effects of co-doping of F and In on structural and optical properties of ZnO thin films were investigated. The concentration ratio of [F]/[Zn] was altered from 0.25 to 1.75 with 0.50 step at.% mole and [In]/[Zn] was altered from 0.25 to 1.00 with 0.25 step at.% mole. X-ray diffraction analysis indicates that the films have polycrystalline nature and the (0 0 2) preferred orientation is the stronger peak. No extra phases involving zinc, fluorine and indium compounds were observed even at high F and In content. The grain size of undoped ZnO and FIZO thin films varied between 15 and 20 nm with a small fluctuation. From the SEM images, although the undoped ZnO had a smooth and particle-shaped surface, FIZO films had nanofiber-networks shapes over the surface with average size of 500 nm. The surface morphologies and crystallite sizes for the F and In doped films were slightly different from than those of undoped film. From the optical study, a slight shrinkage of band gap was backwardly observed from 3.36 to 3.25 eV with the increasing of F and In content.     

Laser energy density, structure and properties of pulsed-laser deposited zinc oxide films

Zinc oxide thin films were deposited on soda lime glass substrates by pulsed laser deposition in an oxygen-reactive atmosphere at 20 Pa and a constant substrate temperature at 300 °C. A pulsed KrF excimer laser, operated at 248 nm with pulse duration 10 ns, was used to ablate the ceramic zinc oxide target. The structure, the optical and electrical properties of the as-deposited films were studied in dependence of the laser energy density in the 1.2-2.8 J/cm² range, with the aid of X-ray Diffraction, Atomic Force Microscope, Transmission Spectroscopy techniques, and the Van der Pauw method, respectively. The results indicated that the structural and optical properties of the zinc oxide films were improved by increasing the laser energy density of the ablating laser. The surface roughness of the zinc oxide film increased with the decrease of laser energy density and both the optical bang gap and the electrical resistivity of the film were significantly affected by the laser energy density.     

退火及超声处理对ZnO薄膜结构和发光特性的影响

 利用对向靶射频磁控溅射系统在Si（100）衬底上制备了ZnO薄膜,并对其进行了退火和超声处理。采用XRD,AFM和光致发光谱对其结构、表面形貌和性能进行了分析。结果表明：沉积态ZnO薄膜（002）择优取向稍差,尺寸较小,表面粗糙度较大。随退火温度的升高,颗粒粒径增大,样品的取向性和结晶度都明显变好,应力状态由压应力转变为张应力,粗糙度降低。超声处理缓解了薄膜中的张应力,晶粒尺寸更趋增大;用波长为280 nm的激发光激发薄膜时,沉积态薄膜无发光峰存在;随着退火温度升高,出现了一个378 nm的紫外峰和一个398 nm的紫峰;紫外峰峰值强度随退火温度升高不断增强,而紫峰的峰位随退火温度升高基本不发生变化,峰值强度增强;700 ℃退火后的薄膜经超声处理后,发光谱中出现了峰值波长为519 nm的绿色发光带。     

Sn doping effects on the electro-optical properties of sol gel derived transparent ZnO films

Undoped and tin (Sn) doped ZnO films have been deposited by sol gel spin coating method. The Sn/Zn nominal volume ratio was 1, 3 and 5% in the solution. The effect of Sn incorporation on structural and electro-optical properties of ZnO films was investigated. All the films have polycrystalline structure, with a preferential growth along the ZnO (002) plane. The crystallite size was calculated using a well-known Scherrer's formula and found to be in the range of 26-16 nm. X-ray diffraction patterns of the films showed that Sn incorporation leads to substantial changes in the structural characteristics of ZnO films. The SEM measurements showed that the surface morphology of the films was affected from the Sn incorporation. The highest average optical transmittance value in the visible region was belonging to the undoped ZnO film. The optical band gap and Urbach energy values of these films were determined. The absorption edge shifted to the lower energy depending on the Sn dopant. The shift of absorption edge is associated with shrinkage effect. The electrical conductivity of the ZnO film enhanced with the Sn dopant. From the temperature dependence of conductivity measurements, the activation energy of ZnO film increased with Sn incorporation.     

退火对ZnO:Al薄膜光致发光性能的影响

 采用溶胶-凝胶工艺在石英衬底上制备ZnO:Al（AZO）薄膜,通过不同温度的退火处理,研究了退火对AZO薄膜结构和光致发光特性的影响。XRD图谱表明：所制备的薄膜具有c轴高度择优取向,随着退火温度的升高,(002)峰的强度逐渐增强,同时(002)峰的半高宽逐渐减小,表明晶粒在不断增大。未退火样品的光致发光（PL）谱由361 nm附近的紫外带边发射峰和500 nm附近的深能级发射峰组成。样品经退火后,以500 nm为中心的绿带发射逐渐减弱,而带边发射强度有所增强,并且逐渐红移到366 nm附近,与吸收边移动的测试结果相吻合。对经过不同时间退火的样品分析表明,AZO薄膜的发光特性与退火时间也有很大关系,时间过短可见波段的发射较强,但时间过长会使晶粒发生团聚,导致紫外发射峰强度减弱。     

Influence of excitation light wavelength on the photoluminescence properties for ZnO films prepared by magnetron sputtering

Highly orientated polycrystalline ZnO films were deposited on sapphire, silicon and quartz substrates at room temperature by r.f. magnetron sputtering. Different photoluminescence (PL) spectra were observed when excited with different wavelength light. A UV emission peak (356 nm) and a blue peak (446 nm) were generated for the films on sapphire, silicon and quartz substrates, and only the 446 nm blue emission appeared for the films on glass substrates when the wavelength of the excitation light was 270 nm. With increasing the wavelength of the excitation light up to 300 and 320 nm, the UV emission disappeared for films on various substrates and the wavelength of the PL peaks increased up to 488 and 516 nm, respectively. When the wavelength of the excitation light increased to 398 nm, the PL spectrum becomes a wide band that is consistent with three emission peaks.     

Conductivity and dielectric properties of sol–gel derived porous zirconia

The 8-mol percentage Y₂O₃-stabilized Porous Zirconia was prepared using sol–gel method. Zirconium oxalate gel was prepared by the addition of appropriate amount of oxalic acid solution into the 1 M aqueous solution of zirconium-oxy chloride. A cubic phase zirconia powder was obtained by calcination and milling of the zirconium oxalate gel. Crystallization temperature was found about 450 °C from the Differential thermal analysis. The phase analysis by X-ray diffraction shows the presence of cubic phase. Pellets sintered at 1,350 °C were highly porous, and the electrical conductivity was found with lower value due to the porosity, and the hardness was about 8.0 GPa. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Effect of excitation and detection angles on photoluminescence spectrum from ZnO nanorod array

The angular dependent photoluminescence from ZnO nanorod array was investigated. Variations in the excitation and detection angles provided to reveal a blue shift and then splitting of a near-band edge emission into two bands. It is suggested that the observed phenomenon is caused by an inhomogeneous distribution of the emission along the nanorod length. The spatially resolved cathodoluminescence measurements confirmed that indeed the emission along the length of the nanorod is inhomogeneous and the top and bottom parts of the nanorod exhibit different emission spectra.     

Effect of ambient temperature on electrical properties of nanostructure n-ZnO/p-Si heterojunction diode

The nanostructure n-ZnO/p-Si heterojunction diode was fabricated by sol–gel method. The structural and morphological properties of the nanostructure ZnO film have been investigated. The X-ray diffraction spectra indicated that the films are of polycrystalline nature. The scanning electron microscopy images indicate that the surface morphology of ZnO film is almost homogeneous and the ZnO film is consisted of the circular formed with coming together of the nanoparticles. The electrical characterization of nanostructure n-ZnO/p-Si heterojunction diode has been investigated by current–voltage characteristics. The ideality factor (n) of the diode was found for different ambient temperatures and the obtained 6.40 value for 296 K is higher than unity due to the interface states between the two semiconductor materials and series resistance. The values of n increased with decreasing ambient temperature. The reverse current of the diode increased with illumination intensity of 100 mW cm⁻² and the diode gave a maximum open circuit voltage V_oc of 0.19 V and short-circuits current I_sc of 8.03 × 10⁻⁸ A.