Simultaneous Determination of Epinephrine and Dopamine by Using Candida tropicalis Yeast Cells Immobilized in a Carbon Paste Electrode Modified with Single Wall Carbon Nanotube

A new electrochemical microbial biosensor system based on Candida tropicalis was developed for the fast detecting of dopamine and epinephrine. Candida tropicalis was immobilized in a carbon paste electrode (CPE) with single wall carbon nanotube (SWCNT). Immobilized cells were used as a origin of the polyphenol oxidase (PPO) to develop voltammetric epinephrine and dopamine biosensor. Voltammetric determination of phenolic compounds such as epinephrine and dopamine a simple technique which is available. Direct oxidation of phenols can be used, but the oxidation potentials of this compounds are similar and they can not be detected distinctively. Another possibility is the use of biosensors based on the polyphenol oxidase (tyrosinase) enzyme that oxidizes the phenolic compounds into their related quinones. By this way, phenolic compounds are epinephrine and dopamine which were used in this study as well detected at different potentials. In this study differential pulse voltammetry and amperometry techniques were used for the determination of dopamine and epinephrine. The effect of varying the amounts of SWCNT and the response of microorganism to epinephrine was investigated to find the optimum composition of the sensor. The effects of pH and temperature were also examined. Increases in biosensor responses obtained by amperometric measurements were linearly related to dopamine concentrations between 0.025 and 0.25 mM and epinephrine concentrations between 0.01 and 0.1 mM. Limits of detection of the biosensor for dopamine and epinephrine were calculated to be 0.008 and 0.0023 mM, respectively. Finally, proposed system was applied to epinephrine and dopamine analysis in pharmaceutical drugs and synthetic serum and the results were compared with LC MS MS method.     

Single-walled carbon nanotube/pyrenecyclodextrin nanohybrids for ultrahighly sensitive and selective detection of p-nitrophenol

Electrochemical detection of p-nitrophenol (P-NP) using a highly sensitive and selective platform based on single-walled carbon nanotube/pyrenecyclodextrin (SWCNT/PyCD) nanohybrids is described for the first time. The electrochemical performance of the SWCNT/PyCD nanohybrid electrode was fully compared with bare glassy carbon, single-SWCNT, single-PyCD, and SWCNT/CD (without pyrene rings) electrodes. Besides the techniques of cyclic voltammetry and chronoamperometric transients, differential pulse voltammetry (DPV) has been used for the detection of P-NP without any interference from o-nitrophenol (O-NP) at the potentials of -0.80 and -0.67 V, respectively. The SWCNT/PyCD nanohybrid electrode is highly sensitive, and it shows an ultrahigh sensitivity of 18.7 μA/μM toward P-NP in contrast to the values reported previously. The detection limit (S/N = 3) of the SWCNT/PyCD nanohybrid electrode toward P-NP is 0.00086 μM (0.12 ppb), which is well below the allowed limit in drinking water, 0.43 μM, given by the U.S. Environmental Protection Agency (EPA). The analytical performance of the SWCNT/PyCD nanohybrid electrode toward P-NP is superior to the existing electrodes.     

Direct electrolytic exfoliation of graphite with hemin and single-walled carbon nanotube: Creating functional hybrid nanomaterial for hydrogen peroxide detection

We present a new, facile and efficient method to prepare functional graphene (GN) hybrid nanomaterials using direct electrolytic exfoliation of graphite robs in hemin (HN) and single-walled carbon nanotube (SWCNT) solution. During the exfoliation process, HN and SWCNT were simultaneously adsorbed on the surface of GN nanosheets through noncovalent π–π interaction, and then 3D GN–HN–SWCNT hybrid nanomaterials were formed. Due to the synergic effect among GN, HN, and SWCNT, these hybrid nanomaterials possessed excellent electrocatalysis properties and were used to construct novel electrochemical biosensor for H₂O₂ determination. The results displayed a wide linear range of 0.2 μM–0.4 mM and a low detection limit of 0.05 μM. Moreover, the developed sensor was successfully applied for real samples, such as beverages, and showed great promise in routine sensing applications.     

电弧放电法制备大面积高纯单壁碳纳米管薄膜

介绍了一种制备大面积高纯度单壁碳纳米管(SWCNT)薄膜的新方法. 利用改进的电弧放电法, 在真空放电室内分别安装两枚石墨极板, 使之形成一个球冠型电容器. 使用这种新型装置, 可以在两枚球冠型石墨极板之间产生一个合适的附加电场和成膜基板, 通过控制放电时间, 可在阴极的球冠型石墨极板上制备出厚度从数微米至1毫米不等的SWCNT薄膜. 场发射扫描电子显微镜(FESEM)、高分辨透射电子显微镜(HRTEM)、拉曼光谱和热重分析(TGA)的表征结果表明, 这个方法可以高效地制备具有高纯度的SWCNT薄膜.     

Controlled preparation of carbon nanotube-conducting polymer composites at the polarisable organic/water interface

The electro-polymerisation of polypyrrole (PPy) at the interface between two immiscible electrolyte solutions (ITIES) is reported. The approach is used to demonstrate the formation of a carbon nanotube (SWCNT)-conducting polymer composite, by performing polymerisation in the presence of an assembly of SWCNT films. The morphology of the SWCNT/PPy nanocomposites was determined using probe and electron microscopy and complementary spectroscopic techniques (EDAX, Raman).     

Ab initio study of Pd-decorated single-walled carbon nanotube with C-vacancy as CO sensor

In this paper, the adsorption of CO onto Pd-decorated (5,5) single-walled carbon nanotube (Pd/SWCNT) and Pd-doped (5,5) single-walled carbon nanotube (Pd/SWCNT-V) has been investigated using ab initio studies. The larger binding energies and charges transfer show that the adsorption of CO onto Pd/SWCNT is more stable than that of CO onto Pd/SWCNT-V. The Pd/SWCNT can be utilized as good sensors for CO molecules due to strong binding energy and large electron charge transfer between the Pd/SWCNT and this molecule. Furthermore, the topological properties of the electron density distributions for intramolecular interactions have been analyzed in terms of the Bader theory of atoms in molecules. Finally, the natural population analysis method has been used to evaluate the Pd–C and Pd/CO interactions.     

Improved Detection Limit and Stability of Amperometric Carbon Nanotube-Based Immunosensors by Crosslinking Antibodies with Polylysine

Amperometric immunosensor configurations featuring covalently bound anti-biotin antibodies (Ab) embedded into a polylysine (PLL)-single walled carbon nanotube (SWCNT) composite layer were evaluated. Assemblies were made by first oxidizing pyrolytic graphite (PG) electrodes to form surface carboxylic acid groups, to which PLL, SWCNTs and anti-biotin were covalently linked. Incorporating SWCNT into PLL-antibody assemblies improved the amperometric detection limit for biotin (Ag) labeled with horseradish peroxidase to 10 fmol mL(-1). Anti-biotin embedded into the PLL matrix had improved thermal stability and retained its binding ability for biotin after exposure to temperatures of 42 degrees C for up to 3 hours, while the noncrosslinked antibody was inactivated at this temperature in several minutes.     

Electrostatic current switching and negative differential resistance behavior in a molecular device based on carbon nanotubes

The electronic transport properties of an all-carbon mechanically controlled molecular device based on carbon nanotubes are studied using non-equilibrium Green's function in combination with density functional theory. A segment of (10,0) single-walled carbon nanutube (SWCNT) is placed concentrically outside a (5,0) SWCNT, namely, a (5,0)@(10,0) double-walled carbon nanotube (DWCNT). It is found that the position, orientation and length scaling of the (10,0) SWCNT have crucial effects on the electronic transport properties of the system. When the (10,0) SWCNT is mechanically pushed forward along the axial direction, alternation of on/off switching behavior under low bias and negative differential resistance behavior under high bias are observed. Significant changes in the electronic transport properties arise when rotating the (10,0) SWCNT around the common axis or adding carbon atom layers in the transport direction. Theoretical explanations are proposed for these phenomena.     

Controlled assembly of Ag nanoparticles and carbon nanotube hybrid structures for biosensing

Here we report a chemical-free, simple, and novel method in which a part from a silver-based anode is controllably used in a straightforward manner to produce silver nanoparticles (Ag NPs) in order to fabricate a controlled assembly of Ag NPs and single walled carbon nanotube (SWCNT) hybrid structures. The attachment and distribution of Ag NPs along SWCNTs have been investigated and characterized by field emission scanning electron microscopy (FESEM). We have achieved the decoration of SWCNTs with different densities of Ag NPs by changing the deposition time, the applied voltage, and the location of carbon nanotubes with respect to the anode. At low voltage, single silver nanoparticle is successfully attached at the open ends of SWCNTs whereas at high voltage, intermediate and full coverage densities of Ag NPs are observed. As voltage is further increased, fractals of Ag NPs along SWCNTs are observed. In addition, a device based on a Ag NPs-SWNT hybrid structure is used for the label-free detection of ssDNA molecules immobilized on it. We believe that the proposed method can be used to decorate and/or assemble metal nanoparticles or fractal patterns along SWCNTs with different novel metals such as gold, silver, and copper and can be exploited in various sensitive applications for fundamental research and nanotechnology.     

The effect of thermal stability of carbon nanotubes on the flame retardancy of epoxy and bismaleimide/carbon fiber/buckypaper composites

Single-walled carbon nanotube (SWCNT) and multi-walled carbon nanotube (MWCNT) membranes (buckypaper) were incorporated onto the surface of epoxy and bismaleimide (BMI) carbon fiber composites. Their flammability behaviors were investigated by a cone calorimeter. The composites with buckypaper reduced the heat release rate (HRR) by more than 60% peak and smoke generation by 50% during combustion. The effects of different buckypaper on the flame retardancy of epoxy and BMI were compared and discussed. Our research team found that buckypapers acted as an effective flame-retardant shield to dramatically reduce the fire hazards of composites if they survived during fire combustion. Thermogravimetric analyses was used to compare the thermo-oxidation stability of the resins and buckypapers to explain the different effects of SWCNT and MWCNT buckypaper on flammability of epoxy and BMI carbon fiber composites.     

Detection of p53 Gene by Using Genomagnetic Assay Combined with Carbon Nanotube Modified Disposable Sensor Technology

Electrochemical monitoring of DNA hybridization related to p53 gene sequence was investigated using genomagnetic assay combined with single walled carbon nanotube (SWCNT) modified pencil graphite electrodes (PGEs). The hybridization was performed either at magnetic beads (MB) surface or in solution. The enhanced guanine signal was obtained using SWCNT‐PGEs compared to one obtained by unmodified PGEs. The selectivity of genomagnetic assay was tested under optimum conditions. The DLs were calculated as 0.88 µM and 0.11 µM for hybridization performed at MB surface and solution, respectively. This selective, practical and cost effective genomagnetic assay combined with SWCNT‐PGEs is reported herein for the first time.     

Synthesis and characterization of styrene grafted carbon nanotube and its polystyrene nanocomposite

Effective side wall functionalization of single-walled carbon nanotube (SWCNT) with 4-vinylaniline was carried out through solvent free functionalization. The functionalized SWCNT was characterized through FT-IR and NMR. Typical peaks to identify the functionalization were observed. Thermal analysis shows around 48% weight loss in functionalized SWCNT in comparison to the pure SWCNT. The ratio of disordered to order transition (I_D/I_G) in FT-Raman, indicated the generation of some surface defects due to functionalization. Near infrared spectrum of functionalized SWCNT also confirmed the functionalization of SWCNT. The polystyrene nanocomposite materials were prepared with functionalized SWCNT as fillers by solution casting from tetrahydrofuran. The functionalized SWCNT nanocomposite showed significant improvement in mechanical properties and electrical properties. The dispersibility of the carbon nanotube in the composite was investigated by using scanning electron microscopy.     

Electronic properties and reactivity of Pt-doped carbon nanotubes

The structures of the (5,5) single-walled carbon nanotube (SWCNT) segments with hemispheric carbon cages capped at the ends (SWCNT rod) and the Pt-doped SWCNT rods have been studied within density functional theory. Our theoretical studies find that the hemispheric cages introduce localized states on the caps. The cap-Pt-doped SWCNT rods can be utilized as sensors because of the sensitivity of the doped Pt atom. The Pt-doped SWCNT rods can also be used as catalysts, where the doped Pt atom serves as the enhanced and localized active center on the SWCNT. The adsorptions of C(2)H(4) and H(2) on the Pt atom in the Pt-doped SWCNT rods reveal different adsorption characteristics. The adsorption of C(2)H(4) on the Pt atom in all of the three Pt-doped SWCNT rods studied (cap-end-doped, cap-doped, and wall-doped) is physisorption with the strongest interaction occurring in the middle of the sidewall of the SWCNT. On the other hand, the adsorption of H(2) on the Pt atom at the sidewall of the SWCNT is chemisorption resulting in the decomposition of H(2), and the adsorption of H(2) at the hemispheric caps is physisorption.     

Dynamics of local chirality during SWCNT growth: armchair versus zigzag nanotubes

We present an analysis of the dynamics of single-walled carbon nanotube (SWCNT) chirality during growth, using the recently developed local chirality index (LOCI) method [ Kim et al. Phys. Rev. Lett. 2011 , 107 , 175505 ] in conjunction with quantum chemical molecular dynamics (QM/MD) simulations. Using (5,5) and (8,0) SWCNT fragments attached to an Fe(38) catalyst nanoparticle, growth was induced by periodically placing carbon atoms at the edge of the SWCNT. For both armchair and zigzag SWCNTs, QM/MD simulations indicate that defect healing-the process of defect removal during growth-is a necessary, but not sufficient, condition for chirality-controlled SWCNT growth. Time-evolution LOCI analysis shows that healing, while restoring the pristine hexagon structure of the growing SWCNT, also leads to changes in the local chirality of the SWCNT edge region and thus of the entire SWCNT itself. In this respect, we show that zigzag SWCNTs are significantly inferior in maintaining their chirality during growth compared to armchair SWCNTs.     

Electrochemical sensing of hydroxylamine by gold nanoparticles on single-walled carbon nanotube films

The arrays of gold nanoparticles (AuNPs) were fabricated on flexible and transparent single-walled carbon nanotube (SWCNT) films using the electrochemical deposition method, and the patterned nanotubes were then used as electrodes for hydroxylamine detection. The sizes and densities of the AuNPs could easily be controlled by varying the amount of charge deposited, and the gold-deposited area showed a homogeneous distribution on the exposed SWCNT film surface. X-ray diffraction analysis of the AuNPs shows a face-centered cubic structure that is dominated by the lowest energy {111} facets. The oxidation of the hydroxylamine on the AuNP-deposited SWCNT films depended strongly on the solution pH, and the maximum catalytic current was observed at a pH of 9.0. A linear electrical response was observed for concentrations ranging from 0.016 to 0.210 mM, and the detection limit and the sensitivity were 0.72 μM and 165.90 μAmM^?1 cm^?2, respectively. Moreover, the amperometric response in hydroxylamine showed a stable response for a long time (300 s), during which time it retained 94% of its initial value. In the long-term storage stability test, the current response to hydroxylamine decreased slightly, with only 17% leakage after 30 days.     

Electrochemically selective determination of dopamine in the presence of ascorbic and uric acids on the surface of the modified Nafion/single wall carbon nanotube/poly(3-methylthiophene) glassy carbon electrodes

A voltammetric method based on a combination of incorporated Nafion, single-walled carbon nanotubes and poly(3-methylthiophene) film-modified glassy carbon electrode (NF/SWCNT/PMT/GCE) has been successfully developed for selective determination of dopamine (DA) in the ternary mixture of dopamine, ascorbic acid (AA) and uric acid (UA) in 0.1M phosphate buffer solution (PBS) pH 4. It was shown that to detect DA from binary DA-AA mixture, the use of NF/PMT/GCE was sufficient, but to detect DA from ternary DA-AA-UA mixture NF/SWCNT/PMT/GCE was required. The later modified electrode exhibits superior electrocatalytic activity towards AA, DA and UA thanks to synergic effect of NF/SWCNT (combining unique properties of SWCNT such as high specific surface area, electrocatalytic and adsorptive properties, with the cation selectivity of NF). On the surface of NF/SWCNT/PMT/GCE AA, DA, UA were oxidized respectively at distinguishable potentials of 0.15, 0.37 and 0.53 V (vs. Ag/AgCl), to form well-defined and sharp peaks, making possible simultaneous determination of each compound. Also, it has several advantages, such as simple preparation method, high sensitivity, low detection limit and excellent reproducibility. Thus, the proposed NF/SWCNT/PMT/GCE could be advantageously employed for the determination of DA in real pharmaceutical formulations.     

Electrocatalytic oxidation of the reduced nicotinamide adenine dinucleotide at carbon ionic liquid electrode modified with polythionine/multi-walled carbon nanotubes composite

A carbon ionic liquid electrode (CILE) was modified with a polythionine (PTh)/multi-walled carbon nanotubes (MWCNTs) composite and used for the detection of reduced nicotinamide adenine dinucleotide (NADH). The electrode was prepared by electrochemical polymerization of thionine on the MWCNTs in neutral medium. Cyclic voltammetry indicated that the electrode was capable of mediating the oxidation of NADH at an overpotential as low as 0.03 V. Amperometric experiments showed that a sensitive and stable response towards NADH is obtained within 5 s. The linear range for the determination of NADH is from 0.8 μmol L^?1 to 422 μmol L^?1, with a detection limit of 0.26 μmol L^?1 (S/N = 3). The wide linear range, lower detection limit and faster response towards NADH suggests that the new method potentially is useful for developing NAD⁺-dependent enzyme-based biosensors.     

Characterization of a tamoxifen-tethered single-walled carbon nanotube conjugate by using NMR spectroscopy

We report the synthesis and characterization of a tamoxifen-tethered single-walled carbon nanotube (SWCNT) conjugate, in which tamoxifen is covalently attached to the single-walled carbon nanotube via oxidation and esterification reactions for the first time. The functionalized SWCNT derivative was characterized by using spectroscopic techniques: IR, UV-vis, Raman, and (1)H NMR Spectroscopy. The attachment of the drug tamoxifen to SWCNTs is analogous to the gold conjugate, which provided an endocrine treatment for breast cancer.     

Statistical sampling of carbon nanotube populations by thermogravimetric analysis

Carbon nanotubes are one of the most promising nanomaterials available with applications in electronics devices, sensing, batteries, composites and medicine. Strict control of the carbon nanotube chemistry and properties is necessary as the applications proceed into more specialized areas. Thermogravimetric analysis (TGA) is one analytical method currently utilized for the characterization of carbon nanotubes. Though TGA can provide quantitative measurements of the composition of a sample, many researchers do not ensure the variance of the sample is properly captured. This research demonstrates for four single-wall carbon nanotube (SWCNT) samples how to statistically evaluate the material with TGA to ensure that the variance within the material is represented. SEM results are used to help reach conclusions about purity of the material by providing a visual means for inspection. This data is used to select the SWCNT material with the lowest variability and highest quality, as evaluated by composition and reproducibility.     

Thickness dependent sensing mechanism in sorted semi-conducting single walled nanotube based sensors

Single walled carbon nanotube (SWCNT) networks present outstanding potential for the development of SWCNT-based gas sensors. Due to the complexity of the transport properties of this material, the physical mechanisms at stake during exposure to gas are still under debate. Previously suggested mechanisms are charge transfer between gas molecules and SWCNT and Schottky barrier modulation. By comparing electrical measurements with an analytical model based on Schottky barrier modulation, we demonstrate that one mechanism or the other is predominant depending on the percolation of metallic carbon nanotubes. Below the metallic SWCNT percolation threshold, sensing is dominated by the modulation of the Schottky barrier, while above this threshold, it is only attributed to a charge transfer between SWCNT and gas molecules. Both mechanisms are discussed in terms of sensitivity and resolution leading to routes for the optimization of a gas sensor architecture based on highly enriched semiconducting carbon nanotube films.