电解液添加剂硫酸亚乙酯对锂离子电池性能的影响

在1 mol/L LiPF₆/碳酸乙烯酯+碳酸二甲酯+碳酸甲乙酯（体积比1∶1∶1）电解液中,采用恒流充放电测试、循环伏安法（CV）、扫描电子显微镜（SEM）、能量散射光谱（EDS）、电化学阻抗谱（EIS）等测试技术,研究了添加剂硫酸亚乙酯（DTD）对锂离子电池性能及石墨化中间相碳微球（MCMB）电极/电解液界面性质的影响。 结果表明,在电解液中引入体积分数0.01%DTD后,MCMB/Li电池可逆放电容量从300 mA·h/g提高至350 mA·h/g,电池总阻抗降低,循环稳定性提高。CV测试发现,在首次还原过程中,DTD在电极电位1.4 V左右（vs Li/Li⁺）发生电化学还原,参与了MCMB电极表面固体电解质相界面膜（SEI膜）的形成过程。 同时,DTD对LiMn₂O₄电极性能无不良影响。     

Monitoring electrode/electrolyte interfaces of Li-ion batteries under working conditions: A surface-enhanced Raman spectroscopic study on LiCoO2 composite cathodes

Lithium-ion batteries are commonly used for electrical energy storage in portable devices and are promising systems for large-scale energy storage. However, their application is still limited due to electrode degradation and stability issues. To enhance the fundamental understanding of electrode degradation, we report on the Raman spectroscopic characterization of LiCoO₂ cathode materials of working Li-ion batteries. To facilitate the spectroscopic analysis of the solid electrolyte interface (SEI), we apply in situ surface-enhanced Raman spectroscopy under battery working conditions by using Au nanoparticles coated with a thin SiO₂ layer (Au@SiO₂). We observe a surface-enhanced Raman signal of Li₂CO₃ at 1090 cm⁻¹ during electrochemical cycling as an intermediate. Its formation/decomposition highlights the role of Li₂CO₃ as a component of the SEI on LiCoO₂ composite cathodes. Our results demonstrate the potential of Raman spectroscopy to monitor electrode/electrolyte interfaces of lithium-ion batteries under working conditions thus allowing relations between electrochemical performance and structural changes to be established.     

The understanding of solid electrolyte interface (SEI) formation and mechanism as the effect of flouro-o-phenylenedimaleimaide (F-MI) additive on lithium-ion battery

Solid electrolyte interface (SEI) is a critical factor that influences battery performance. SEI layer is formed by the decomposition of organic and inorganic compounds after the first cycle. This study investigates SEI formation as a product of electrolyte decomposition by the presence of flouro-o-phenylenedimaleimaide (F-MI) additive. The presence of fluorine on the maleimide-based additive can increase storage capacity and reversible discharge capacity due to high electronegativity and high electron-withdrawing group. The electrolyte containing 0.1 wt% of F-MI-based additive can trigger the formation of SEI, which could suppress the decomposition of remaining electrolyte. The reduction potential was 2.35 to 2.21 V vs Li/Li⁺ as examined by cyclic voltammetry (CV). The mesocarbon microbeads (MCMB) cell with F-MI additive showed the lowest SEI resistance (Rsei) at 5898 Ω as evaluated by the electrochemical impedance spectroscopy (EIS). The morphology and element analysis on the negative electrode after the first charge-discharge cycle were examined by scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), and X-ray photoelectron spectroscopy (XPS). XPS result showed that MCMB cell with F-MI additive provides a higher intensity of organic compounds (RCH₂OCO₂Li) and thinner SEI than MCMB cell without an additive that provides a higher intensity of inorganic compound (Li₂CO₃ and Li₂O), which leads to the performance decay. It is concluded that attaching the fluorine functional group on the maleimide-based additive forms the ideal SEI formation for lithium-ion battery.     

Effects of Solid Electrolyte Interphase Components on the Reduction of LiFSI over Lithium Metal

The use of a lithium metal anode still presents a challenging chemistry and engineering problem that holds back next generation lithium battery technology. One of the issues facing lithium metal is the presence of the solid electrolyte interphase (SEI) layer that forms on the electrode creating a variety of chemical species that change the properties of the electrode and is closely related to the formation and growth of lithium dendrites. In order to advance the scientific progress of lithium metal more must be understood about the fundamentals of the SEI. One property of the SEI that is particularly critical is the passivating behavior of the different SEI components. This property is critical to the continued formation of SEI and stability of the electrolyte and electrode. Here we report the investigation of the passivation behavior of Li₂O, Li₂CO_3, LiF and LiOH with the lithium salt LiFSI. We used large computational chemistry models that are able to capture the lithium/SEI interface as well as the SEI/electrolyte interface. We determined that LiF and Li₂CO₃ are the most passivating of the SEI layers, followed by LiOH and Li₂O. These results match previous studies of other Li salts and provide further examination of LiFSI reduction.     

Studies on the effects of coated Li2CO3 on lithium electrode

Although a lithium metal anode has a high energy density compared with a carbon insertion anode, the poor rechargeability prevents the practical use of anode materials. A lithium electrode coated with Li₂CO₃ was prepared as a negative electrode to enhance cycleability through the control of the solid electrolyte interface (SEI) layer formation in Li secondary batteries. The electrochemical characteristics of the SEI layer were examined using chronopotentiometry (CP) and impedance spectroscopy. The Li₂CO₃-SEI layer prevents electrolyte decomposition reaction and has low interface resistance. In addition, the lithium ion diffusion in the SEI layer of the uncoated and the Li₂CO₃-coated electrode was evaluated using chronoamperometry (CA).     

Investigation of interfacial processes in graphite thin film anodes of lithium-ion batteries by both in situ and ex situ infrared spectroscopy

Graphite thin film anodes with a high IR reflectivity have been prepared by a spin coating method. Both ex situ and in situ microscope FTIR spectroscopy (MFTIRS) in a reflection configuration were employed to investigate interfacial processes of the graphite thin film anodes in lithium-ion batteries. A solid electrolyte interphase layer (SEI layer) was formed on the cycled graphite thin film anode. Ex situ MFTIRS revealed that the main components of the SEI layer on cycled graphite film anodes in 1 mol L -1 LiPF6 /ethylene carbonate + dimethyl carbonate (1:1) are alkyl lithium carbonates (ROCO2 Li). The desolvation process on graphite anodes during the initial intercalation of lithium ion with graphite was also observed and analyzed by in situ MFTIRS.     

In-situ spectroelectrochemical analysis of the passivating surface film formed on a carbon film electrode as a function of the water content in 1 M LiPF6-EC/DEC solution

The in-situ spectroelectrochemical technique has been applied to investigate the role of water in the formation of a passivating surface film on a plasma enhanced chemical vapor deposited (PECVD) carbon film electrode in 1 M LiPF₆-ethylene carbonate (Li-EC) and diethyl carbonate (DEC) solution, combined with cyclic voltammetry. In-situ Fourier transform infra-red (FTIR) spectra of the surface film showed that all the peak intensities of the Li₂CO₃, ROCO₂Li, and LiPF₆ constituents significantly increase with increasing water content under application of the negative potentials with respect to open circuit potential (OCP). It is suggested that the reduction of Li-EC to ROCO₂Li runs via a one-electron transfer pathway with the help of the unrestricted supply of the electron transfer path as a result of diffusion of water through the surface film; then Li₂CO₃ formation proceeds concurrently by the chemical reaction of ROCO₂Li with water. Moreover, the compact sedimentation of ROCO₂Li in the presence of water in the electrolyte is subjected to severe interference of the salt reduction product, Li_xPF_y, than in the absence of water in the electrolyte. These FTIR results coincide well with those of cyclic voltammetry. From the combined results of in-situ FTIR spectroscopy and cyclic voltammetry, it is indicated that, unlike other salt and solvent reaction products, ROCO₂Li, Li₂CO₃ and Li_xPF_y simultaneously increase to constitute the outer layer of the surface film with equal amounts. Received: 24 February 1998 / Accepted: 6 June 1998     

In-situ spectroelectrochemical analysis of the passivating surface film formed on a carbon film electrode as a function of the water content in 1 M LiPF6-EC/DEC solution

The in-situ spectroelectrochemical technique has been applied to investigate the role of water in the formation of a passivating surface film on a plasma enhanced chemical vapor deposited (PECVD) carbon film electrode in 1 M LiPF₆-ethylene carbonate (Li-EC) and diethyl carbonate (DEC) solution, combined with cyclic voltammetry. In-situ Fourier transform infra-red (FTIR) spectra of the surface film showed that all the peak intensities of the Li₂CO₃, ROCO₂Li, and LiPF₆ constituents significantly increase with increasing water content under application of the negative potentials with respect to open circuit potential (OCP). It is suggested that the reduction of Li-EC to ROCO₂Li runs via a one-electron transfer pathway with the help of the unrestricted supply of the electron transfer path as a result of diffusion of water through the surface film; then Li₂CO₃ formation proceeds concurrently by the chemical reaction of ROCO₂Li with water. Moreover, the compact sedimentation of ROCO₂Li in the presence of water in the electrolyte is subjected to severe interference of the salt reduction product, Li_xPF_y, than in the absence of water in the electrolyte. These FTIR results coincide well with those of cyclic voltammetry. From the combined results of in-situ FTIR spectroscopy and cyclic voltammetry, it is indicated that, unlike other salt and solvent reaction products, ROCO₂Li, Li₂CO₃ and Li_xPF_y simultaneously increase to constitute the outer layer of the surface film with equal amounts.     

一种新型复合微孔聚合物电解质及其与锂离子电池负极相容性研究

以介孔分子筛SBA-15为造孔剂和填料, 研究出一种无需使用增塑剂制备复合微孔型聚合物电解质(SBA-15 CMPE)的新方法. 组装Li/SBA-15 CMPE/Li对称电池, 并利用电化学阻抗谱(EIS)技术研究了存放时间、循环伏安(CV)扫描、恒电流极化以及环境温度等对Li/SBA-15 CMPE界面性质的影响. 通过将成膜浆料直接浇铸在用水性粘合剂制备的中间相微球碳(MCMB)电极片上, 制备附有SBA-15 CMPE的一体化电极(MCMB/SBA-15 CMPE). 用该MCMB/SBA-15 CMPE所组装的三电极模拟电池具有良好的循环性能, EIS研究揭示了其首次阴极极化过程中碳电极上SEI膜的形成、生长和稳定的过程.     

LiCoO<Subscript>2</Subscript> electrode/electrolyte interface of Li-ion batteries investigated by electrochemical impedance spectroscopy

The storage behavior and the first delithiation of LiCoO₂ electrode in 1 mol/L LiPF₆-EC:DMC:DEC electrolyte were investigated by electrochemical impedance spectroscopy (EIS). It has found that, along with the increase of storage time, the thickness of SEI film increases, and some organic carbonate lithium compounds are formed due to spontaneous reactions occurring between the LiCoO₂ electrode and the electrolyte. When electrode potential is changed from 3.8 to 3.95 V, the reversible breakdown of the resistive SEI film occurs, which is attributed to the reversible dissolution of the SEI film component. With the increase of electrode potential, the thickness of SEI film increases rapidly above 4.2 V, due to overcharge reactions. The inductive loop observed in impedance spectra of the LiCoO₂ electrode in Li/LiCoO₂ cells is attributed to the formation of a Li_1−x CoO₂/LiCoO₂ concentration cell. Moreover, it has been demonstrated that the lithium-ion insertion-deinsertion in LiCoO₂ hosts can be well described by both Langmuir and Frumkin insertion isotherms, and the symmetry factor of charge transfer has been evaluated at 0.5. Supported by the Special Funds for Major State Basic Research Project of China (Grant No. 2002CB211804)     

Electrochemical SPM investigation of the solid electrolyte interphase film formed on HOPG electrodes

Solid electrolyte interphase (SEI) film formation on graphite electrodes was studied on highly oriented pyrolytic graphite (HOPG) in nonaqueous electrolyte by in situ electrochemical atomic force microscopy (AFM). For potentials negative to 0.7 V versus Li|Li⁺ a SEI film is formed on the HOPG electrode surface. After the first cycle the film is rough and covers the surface of the HOPG electrode only partially. After the second cycle the HOPG surface is fully covered by a compact film. The thickness of the SEI film was measured by increasing the pressure of the AFM tip and thus scraping a part of the electrode surface. In this way a thickness of about 25 nm was found for the SEI film formed after two scan cycles between 3 and 0.01 V versus Li|Li⁺.     

Determining the pure component spectra of trace organometallic intermediates by combined application of in situ Raman spectroscopy and band-target entropy minimization analysis

Trace organometallic intermediates arising from complex organic syntheses are usually quite difficult to detect spectroscopically. In situ FTIR and in situ NMR are the only techniques that are used with any regularity for such studies. In this contribution, high-pressure in situ Raman spectroscopic measurements were performed for the rhodium catalyzed hydroformylation of 3,3-dimethylbut-1-ene using Rh₄(CO)₁₂ as catalyst precursor at 298 K – a reaction extensively studied previously by more sensitive in situ FTIR. The Raman spectroscopic measurements were analyzed using the band-target entropy minimization (BTEM) algorithm. As expected, the pure component spectra of dissolved CO, 3,3-dimethylbut-1-ene, and 4,4-dimethylpentanal were easily recovered. In addition, the pure component spectra of the precursor Rh₄(CO)₁₂ and the intermediate RCORh(CO)₄ (R = (CH₃)₃CCH₂CH₂) were successfully reconstructed – even though the mean concentrations of both species were on the order of 150 ppm. The BTEM estimate of the Raman spectrum of RCORh(CO)₄ is reported for the first time. This Raman spectrum is consistent with the DFT predicted spectrum. This study represents the first combined application of Raman spectroscopy and BTEM analysis to a homogeneously catalyzed metal-mediated reaction. The potential and limitations of this general approach are discussed.     

Surface film formation on a graphite electrode in Li‐ion batteries: AFM and XPS study

The formation of a passivation film (solid electrolyte interphase, SEI) at the surface of the negative electrode of full LiCoO₂/graphite lithium‐ion cells using LiPF₆ (1M ) in carbonate solvents as electrolyte was investigated by means of x‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The analyses were carried out at different potentials of the first and the fifth cycles, showing the potential‐dependent character of the surface‐film species formation. These species were mainly identified as Li₂CO₃ up to 3.8 V and LiF up to 4.2 V. This study shows the formation of the SEI during charging and its partial dissolution during discharge. Copyright © 2005 John Wiley & Sons, Ltd.     

Fluoroethylene Carbonate Enabling a Robust LiF‐rich Solid Electrolyte Interphase to Enhance the Stability of the MoS2 Anode for Lithium‐Ion Storage

As a high‐capacity anode for lithium‐ion batteries (LIBs), MoS₂ suffers from short lifespan that is due in part to its unstable solid electrolyte interphase (SEI). The cycle life of MoS₂ can be greatly extended by manipulating the SEI with a fluoroethylene carbonate (FEC) additive. The capacity of MoS₂ in the electrolyte with 10 wt % FEC stabilizes at about 770 mAh g^?1 for 200 cycles at 1 A g^?1, which far surpasses the FEC‐free counterpart (ca. 40 mAh g^?1 after 150 cycles). The presence of FEC enables a robust LiF‐rich SEI that can effectively inhibit the continual electrolyte decomposition. A full cell with a LiNi_0.5Co_0.3Mn_0.2O₂ cathode also gains improved performance in the FEC‐containing electrolyte. These findings reveal the importance of controlling SEI formation on MoS₂ toward promoted lithium storage, opening a new avenue for developing metal sulfides as high‐capacity electrodes for LIBs.     

A Liquid/Liquid Electrolyte Interface that Inhibits Corrosion and Dendrite Growth of Lithium in Lithium‐Metal Batteries

A proof‐of‐concept study on a liquid/liquid (L/L) two‐phase electrolyte interface is reported by using the polarity difference of solvent for the protection of Li‐metal anode with long‐term operation over 2000 h. The L/L electrolyte interface constructed by non‐polar fluorosilicane (PFTOS) and conventionally polar dimethyl sulfoxide solvents can block direct contact between conventional electrolyte and Li anode, and consequently their side reactions can be significantly eliminated. Moreover, the homogeneous Li‐ion flow and Li‐mass deposition can be realized by the formation of a thin and uniform solid‐electrolyte interphase (SEI) composed of LiF, Li_xC, Li_xSiO_y between PFTOS and Li anode, as well as the super‐wettability state of PFTOS to Li anode, resulting in the suppression of Li dendrite formation. The cycling stability in a lithium–oxygen battery as a model is improved 4 times with the L/L electrolyte interface.     

Effect of sulfolane on the morphology and chemical composition of the solid electrolyte interphase layer in lithium bis(oxalato)borate‐based electrolyte

To discuss the source of sulfolane (SL) in decreasing the interface resistance of Li/mesophase carbon microbeads cell with lithium bis(oxalate)borate (LiBOB)‐based electrolyte, the morphology and the composition of the solid electrolyte interphase (SEI) layer on the surface of carbonaceous anode material have been investigated. Compared with the cell with 0.7 mol l^?1 LiBOB‐ethylene carbonate/ethyl methyl carbonate (EMC) (1 : 1, v/v) electrolyte, the cell with 0.7 mol l^?1 LiBOB‐SL/EMC (1 : 1, v/v) electrolyte shows better film‐forming characteristics in SEM (SEI) spectra. According to the results obtained from Fourier transform infrared spectroscopy, XPS, and density functional theory calculations, SL is reduced to Li₂SO₃ and LiO₂S(CH₂)₈SO₂Li through electrochemical processes, which happens prior to the reduction of either ethylene carbonate or EMC. It is believed that the root of impedance reduction benefits from the rich existence of sulfurous compounds in SEI layer, which are better conductors of Li⁺ ions than analogical carbonates. Copyright © 2013 John Wiley & Sons, Ltd.     

Spatiotemporal Changes of the Solid Electrolyte Interphase in Lithium‐Ion Batteries Detected by Scanning Electrochemical Microscopy

The solid electrolyte interphase (SEI) in lithium‐ion batteries separates the highly reductive lithiated graphite from reducible electrolyte components. It is critical for the performance, durability, and safe operation of batteries. In situ imaging of the SEI is demonstrated using the feedback mode of scanning electrochemical microscopy (SECM) with 2,5‐di‐tert‐butyl‐1,4‐dimethoxy benzene as mediator. The formation of the SEI is indicated by a decrease of the mediator regeneration rate. Prolonged imaging of the same region revealed fluctuation of the passivating properties on time scales between 2 min and 20 h with an inhomogeneous distribution over the sample. The implications of the approach for in situ assessment of local SEI properties on graphite electrodes are discussed with respect to studying the influence of mechanical stress on SEI reliability and the mode of action of electrolyte additives aiming at improving SEI properties.     

Effects of current densities on the formation of LiCoO<Subscript>2</Subscript>/graphite lithium ion battery

The activation characteristics and the effects of current densities on the formation of a separate LiCoO₂ and graphite electrode were investigated and the behavior also was compared with that of the full LiCoO₂/graphite batteries using various electrochemical techniques. The results showed that the formation current densities obviously influenced the electrochemical impedance spectrum of Li/graphite, LiCoO₂/Li, and LiCoO₂/graphite cells. The electrolyte was reduced on the surface of graphite anode between 2.5 and 3.6 V to form a preliminary solid electrolyte interphase (SEI) film of anode during the formation of the LiCoO₂/graphite batteries. The electrolyte was oxidized from 3.95 V vs Li⁺/Li on the surface of LiCoO₂ to form a SEI film of cathode. A highly conducting SEI film could be formed gradually on the surface of graphite anode, whereas the SEI film of LiCoO₂ cathode had high resistance. The LiCoO₂ cathode could be activated completely at the first cycle, while the activation of the graphite anode needed several cycles. The columbic efficiency of the first cycle increased, but that of the second decreased with the increase in the formation current of LiCoO₂/graphite batteries. The formation current influenced the cycling performance of batteries, especially the high-temperature cycling performance. Therefore, the batteries should be activated with proper current densities to ensure an excellent formation of SEI film on the anode surface.     

五种1-烷基-2,3-二甲基咪唑型离子液体的合成及作为Li/LiFeO_4电池电解液的研究

合成了五种新的1-烷基-2,3-二甲基咪唑二(三氟甲基磺酰)亚胺离子液体(alkyl-DMimTFSI).以离子液体作为Li/LiFeO4电池电解液,分别考察不同烷基(正丁基、正戊基、正辛基、异辛基和正癸基)对电解液理化性质、界面性质和电池行为的影响.结果表明离子液体的电化学窗口都可以达到5.6V(-0.4～5.2Vvs.Li+/Li),显示它们具有较好的电化学稳定性.加入碳酸亚乙烯酯作为添加剂后,离子液体电解液在Li负极形成稳定的固体电解质相界面膜(SEI),从而提高了Li负极的稳定性,保护了Li片不受腐蚀.电化学阻抗和循环伏安分析进一步揭示LiFeO4正极与离子液体电解液也有良好的兼容性.此外,研究还表明离子液体中烷基种类严重影响它们的电池行为.采用butyl-DMimTFSI和amyl-DMimTFSI电解液体系的电池充放电容量和可逆性明显优于另外三种离子液体,它们的首次放电容量分别达到145和152.6mAh/g,并表现出良好的充放电循环性能.因粘度最大,采用isooctyl-DMimTFSI电解液的电池首次放电容量仅为8.3mAh/g,但添加碳酸丙烯酯(质量比1∶1)稀释后首次放电容量上升至132.4mAh/g.     

Model Studies on the Formation of the Solid Electrolyte Interphase: Reaction of Li with Ultrathin Adsorbed Ionic-Liquid Films and Co3O4(111) Thin Films

In this work we aim towards the molecular understanding of the solid electrolyte interphase (SEI) formation at the electrode electrolyte interface (EEI). Herein, we investigated the interaction between the battery-relevant ionic liquid (IL) 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide (BMP-TFSI), Li and a Co₃O₄(111) thin film model anode grown on Ir(100) as a model study of the SEI formation in Li-ion batteries (LIBs). We employed mostly X-ray photoelectron spectroscopy (XPS) in combination with dispersion-corrected density functional theory calculations (DFT-D3). If the surface is pre-covered by BMP-TFSI species (model electrolyte), post-deposition of Li (Li⁺ ion shuttle) reveals thermodynamically favorable TFSI decomposition products such as LiCN, Li₂NSO₂CF₃, LiF, Li₂S, Li₂O₂, Li₂O, but also kinetic products like Li₂NCH₃C₄H₉ or LiNCH₃C₄H₉ of BMP. Simultaneously, Li adsorption and/or lithiation of Co₃O₄(111) to Li_nCo₃O₄ takes place due to insertion via step edges or defects; a partial transformation to CoO cannot be excluded. Formation of Co⁰ could not be observed in the experiment indicating that surface reaction products and inserted/adsorbed Li at the step edges may inhibit or slow down further Li diffusion into the bulk. This study provides detailed insights of the SEI formation at the EEI, which might be crucial for the improvement of future batteries.