The optimized preparation and electrochemical properties of LiMn1.95Co0.05O4 and Al2O3-coated LiMn1.95Co0.05O4

Cathode material LiMn_1.95Co_0.05O₄ for lithium ion battery was synthesized via solid state reaction, and calcination temperature and time were investigated, respectively. Thermogravimetry (TG) and differential thermal analysis (DTA) measurements were utilized to determine the calcination temperature of precursor sample. The optimized calcination temperature and time are 850 °C and 15 h. The surface of LiMn_1.95Co_0.05O₄ cathode is coated using Al₂O₃ coating materials. The phase structures, surface morphologies, and element types of the prepared LiMn_1.95Co_0.05O₄ and Al₂O₃-coated LiMn_1.95 Co_0.05O₄ were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and energy spectrum analysis (EDS). The 0.5 wt% Al₂O₃-coated compound exhibited better specific capacity and capacity retention than bare sample. The initial discharge capacity was 140.9 mAh/g and capacity retention was 96.7 % after 10 cycles at 0.1 C. Such enhancements are attributed to the presence of a stable Al₂O₃ layer which acts as the interfacial stabilizer on the surface of LiMn_1.95Co_0.05O₄.     

Ultrathin surface coatings to enhance cycling stability of LiMn2O4 cathode in lithium-ion batteries

Spinel LiMn₂O₄ suffers from severe dissolution when used as a cathode material in rechargeable Li-ion batteries. To enhance the cycling stability of LiMn₂O₄, we use the atomic layer deposition (ALD) method to deposit ultrathin and highly conformal Al₂O₃ coatings (as thin as 0.6–1.2 nm) onto LiMn₂O₄ cathodes with precise thickness control at atomic scale. Both bare and ALD-coated cathodes are cycled at a specific current of 300 mA g^?1 (2.5 C) in a potential range of 3.4–4.5 V (vs. Li/Li⁺). All ALD-coated cathodes exhibit significantly improved cycleability compared to bare cathodes. Particularly, the cathode coated with six Al₂O₃ ALD layers (0.9 nm thick) shows the best cycling performance, delivering an initial capacity of 101.5 mA h?g^?1 and a final capacity of 96.5 mA h?g^?1 after 100 cycles, while bare cathode delivers an initial capacity of 100.6 mA h?g^?1 and a final capacity of only 78.6 mA h?g^?1. Such enhanced electrochemical performances of ALD-coated cathodes are ascribed to the high-quality ALD oxide coatings that are highly conformal, dense, and complete, and thus protect active material from severe dissolution into electrolytes. Besides, cycling performances of coated cathodes can be easily optimized by accurately tuning coating thickness via varying ALD growth cycles.     

Synthesis of sea urchin-like LiMn2O4 hollow macrospheres via in situ conversion for rechargeable lithium-ion batteries

Among several materials (transition metal oxide) under development for use as a cathode in lithium-ion batteries, cubic spinel LiMn₂O₄ is one of the most promising cathode materials. In this study, the sea urchin-like LiMn₂O₄ hollow macrospheres were synthesized by using sea urchin-like α-MnO₂ precursors through solid-state in situ self-sacrificing conversion route. The as-prepared LiMn₂O₄ was assembled by many single-crystalline “thorns” of ca.10–20 nm in diameter and ca. 400–500 nm in length. Galvanostatic battery testing showed that sea urchin-like LiMn₂O₄ had an initial discharge capacity of 126.8 mAh/g at the rate of 0.2 C in the potential range between 3.0 and 4.5 V. More than 96.67 % of the initial discharge capacity was maintained for over 50 cycles. The improved electrochemical properties were attributed to the reduced particle size and enhanced electrical contacts by the materials. This particular sea urchin-like structured composite conceptually provides a new strategy for designing electrodes in energy storage applications.     

Improvement of storage performance of LiMn2O4/graphite battery with AlF3-coated LiMn2O4

LiMn₂O₄/graphite batteries using AlF₃-coated LiMn₂O₄ have been fabricated and their electrochemical performance including discharge capacity and cyclic and storage performances have been tested and compared with pristine LiMn₂O₄/graphite batteries. The LiMn₂O₄/graphite battery with AlF₃-coated LiMn₂O₄ shows better capacity (108.5 mAhg^?1), cyclic performance (capacity retention of 92.7 % after 70 cycles), and capacity recovery ratio (98.6 %) than the pristine LiMn₂O₄ battery. X-ray diffraction patterns shows that the spinel structure of AlF₃-coated LiMn₂O₄ can be controlled better than that of pristine LiMn₂O₄ after storage. The improvement in electrochemical performance of the AlF₃-coated LiMn₂O₄/graphite battery is due to the fact that AlF₃ acts as a stabilizer and can protect the oxide structure from damaging during storage, leading to a smaller resistance and polarization after storage.     

Effect of heptamethyldisilazane on the electrochemical performance of LiMn2O4/Li

The effect of heptamethyldisilazane as an electrolyte stabilizer on the cycling performance of a LiMn₂O₄/Li cell at different rates at 30 °C and the storage performance at 60 °C is investigated systematically based on conductivity test, linear sweep voltage, electrochemical impedance spectroscopy, scanning electron microscopy, X-ray diffraction, and charge–discharge measurements. The results show that heptamethyldisilazane added into the LiPF₆-based electrolyte can increase the stability of the original electrolyte; coulomb efficiency, the initial discharge capacity, and cycling performance at different rates in a sense, meanwhile, improve the storage performance at elevated temperature, although the C-rate performance of the cell is a little worse than that without heptamethyldisilazane in the electrolyte. When the LiMn₂O₄/Li cell with heptamethyldisilazane in the LiPF₆-based electrolyte stored at 60 °C for a week cycles 300 times, the capacity retention is up to 91.18 %, which is much higher than that (87.18 %) without the additive in the electrolyte. This is mainly due to the lower solid electrolyte interface resistance (R _f) in the cell, followed by the better morphology and structure of the cathode after storage at 60 °C for a week compared with the LiMn₂O₄/Li cell without heptamethyldisilazane.     

ZnO-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material for lithium-ion batteries synthesized by a combustion method

ZnO-coated LiMn₂O₄ cathode materials were prepared by a combustion method using glucose as fuel. The phase structures, size of particles, morphology, and electrochemical performance of pristine and ZnO-coated LiMn₂O₄ powders are studied in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), galvanostatic charge-discharge test, and X-ray photoelectron spectroscopy (XPS). XRD patterns indicated that surface-modified ZnO have no obvious effect on the bulk structure of the LiMn₂O₄. TEM and XPS proved ZnO formation on the surface of the LiMn₂O₄ particles. Galvanostatic charge/discharge test and rate performance showed that the ZnO coating could improve the capacity and cycling performance of LiMn₂O₄. The 2 wt% ZnO-coated LiMn₂O₄ sample exhibited an initial discharge capacity of 112.8 mAh g^?1 with a capacity retention of 84.1 % after 500 cycles at 0.5 C. Besides, a good rate capability at different current densities from 0.5 to 5.0 C can be acquired. CV and EIS measurements showed that the ZnO coating effectively reduced the impacts of polarization and charge transfer resistance upon cycling.     

Investigation on the storage performance of LiMn2O4 at elevated temperature with the mixture of electrolyte stabilizer

In order to investigate the effect of different electrolytes of LiPF₆-based and LiPF₆-based with the mixed additives of ethanolamine and heptamethyldisilazane on the storage performance of LiMn₂O₄, the commercial LiMn₂O₄ are added into these different electrolytes for storing deliberately at 60 °C in air for 4 h. The results show that the electrolyte with additives can prevent LiMn₂O₄ from being eroded by HF to a certain extent, and improve the storage performance of the material. The initial discharge capacities are 97.7 and 88.4 mAh g^?1 at 0.1 and 1?C, respectively, which are much higher than that 84.4 and 63.6 mAh?g^?1 of LiMn₂O₄ stored in the electrolyte without additives. Moreover, the former LiMn₂O₄ retains 89.1 % of its initial discharge capacity at 1?C after 150 cycles, while this is not up to 84 % for the latter.     

Origin of self-discharge mechanism in LiMn2O4-based Li-ion cells: A chemical and electrochemical approach

LiMn₂O₄-based Li-ion cells suffer from a limited cycle-life and a poor storage performance at 55 °C, both in their charged and discharged states. To get some insight on the origin of the poor 55 °C storage performance, the voltage distribution through plastic Li-ion cells during electrochemical testing was monitored by means of 3-electrode type measurements. From these measurements, coupled with chemical analysis, X-ray diffraction and microscopy studies, one unambiguously concludes that the poor performance of LiMn₂O₄/C-cells at 55 °C in their discharged state is due to enhanced Mn dissolution that increases with increasing both the temperature and the electrolyte HF content. These results were confirmed by a chemical approach which consists in placing a fresh LiMn₂O₄ electrode into a 55 °C electrolyte solution. A mechanism, based on an ion-exchange reaction leading to the Mn dissolution is proposed to account for the poor storage performance of LiMn₂O₄/C Li-ion cells in their discharged state. In order to minimize the Mn dissolution, two surface treatments were performed. The first one consists in applying an inorganic borate glass composition to the LiMn₂O₄ surface, the second one in using an acetylacetone complexing agent. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

Evaluation of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>-LiNi<Subscript>0.80</Subscript>Co<Subscript>0.15</Subscript>Al<Subscript>0.05</Subscript>O<Subscript>2</Subscript> hybrid material as cathode in soft-packed lithium ion battery

The major electrochemical performances of LiMn₂O₄ (LMO)-LiNi_0.80Co_0.15Al_0.05O₂ (NCA) blending cathodes with full-range ratios are evaluated in industrial perspective. The results indicate that the reversible lithium ions can be fully utilized when NCA percentage reaches up to 50 %. The median voltages of blends are higher than the value calculated from a linear relationship of the two pristine cathodes, which is beneficial to energy density. But a synergy effect on room-temperature cycle performance is not observed for the hybrid cathode. However, the high-temperature (45 °C) capacity retention with 70 % NCA is 97.9 % after 100 cycles, higher than both pristine cathodes. It is not until NCA content increases to more than 50 % that the high-rate performance is much deteriorated. Additionally, the swelling of fully charged pouch-type battery after 4 h storage at 85 °C disappears when NCA percentage is less than 50 %. Hence, it is practically manifested that critical flaws of NCA and LMO can be compromised by blending with each other in a critical ratio. In this way, NCA can be practically used in soft-packed battery.     

Synthesis and electrochemical studies of LiMn1−xCuXO4 cathode material

LiMn_1.8Cu_0.2O₄ was investigated in order to improve the electrochemical properties of LiMn₂O₄. We report the synthesis and characterization of materials prepared by solid-state reaction. The structural properties evaluated by the X-ray diffraction and vibrational spectroscopy show that a single phase was formed. Conductivity of LiMn_1.8Cu_0.2O₄ cathode is found to be 8×10⁻⁶ S/cm at 25 °C. The cyclic voltammetry data shows the reversibility of the electrode material. Paper presented at the 7th Euroconference on Ionics, Calcatoggio, Corsica, France, Oct. 1–7, 2000.     

Improvement of cycling stability of LiMn2O4 cathode by Fe2O3 surface modification for Li-ion battery

The surface of spinel LiMn₂O₄ was modified with Fe₂O₃ (1.0, 2.0, 3.0, 4.0, and 5.0 wt%) by a simple sol-gel method to improve its electrochemical performance at room temperature. Compared with bare LiMn₂O₄, surface modification improved cycling stability of the material. Among the surface-modified cathode materials, the 3.0- and 4.0-wt% surface-modified cathodes have lesser capacity loss than the others. While the bare LiMn₂O₄ showed 25.4 % capacity loss in 70 cycles at room temperature, 3.0 and 4.0 wt% of Fe₂O₃-modified LiMn₂O₄ only exhibited the capacity loss of 2.6 and 2.3 % in 70 cycles at room temperature, respectively. The structure and phase were identified with X-ray diffractometer along with the lattice constant calculated by a Win-Metric program.     

LiPF6-EC-MPC electrolyte for LiMn2O4 cathode in lithium-ion battery

Methyl propyl carbonate (MPC) is a promising single solvent for lithium-ion battery without addition of ethylene carbonate (EC), but it is unstable upon cycling because of exposure to the spinel LiMn₂O₄ cathode. Thus, we attempted to add EC to MPC in order to form LiPF₆-EC-MPC electrolyte; the effects of solvent ratio and salt concentration on the cycling performance of LiMn₂O₄ cathode were also investigated. The experiments were characterized by conductivity measurements, charge-discharge at a constant current density and voltage–capacity curves at low temperature. To further enhance our understanding of the performance improvement of LiMn₂O₄/Li cells, the electrochemical characterization techniques (such as, LSV, EIS) were performed on these cells. The results show that the ionic conductivity of the electrolyte and the cycling performance of the spinel LiMn₂O₄ cathode have been dramatically enhanced. From the point of view of operation at low temperature (− 20 °C), 1 M LiPF₆ EC/MPC (1/3) electrolyte is highly recommended for spinel LiMn₂O₄ cathode in lithium-ion battery.     

Storage performance with different charged state of manganese spinel battery

The power battery was manufactured with the commercial LiMn₂O₄ and graphite, and its storage performances with different charged state were studied. Structure, morphology, and surface-state change of the LiMn₂O₄ before and after storage were observed by XRD, SEM, XPS, CV, and AC technique, respectively. The electrochemical performances of LiMn₂O₄ battery were tested. The result shows that the capacity recovery of LiMn₂O₄ stored at discharge state is best (99.2%). While that of full-charged state is worst (93.6%). The cyclic performance of LiMn₂O₄ battery after storage is improved. The cyclic performance of LiMn₂O₄ stored at full-charged state is best (capacity retention ratio of 89.8% after 200?cycles), while that of before storage is 83.0%. The crystal of the spinel was destroyed after storage, and the intensity of breakage is increased with charge state increasing. The amount of soluble Mn and Li-ion migration resistance (R _f) are increased with charge state increasing, and the oxygen loss is detected.     

Recent progress in the electrolytes for improving the cycling stability of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> high-voltage cathode

High-voltage spinel LiNi_0.5Mn_1.5O₄ has been considered one of the most promising cathode materials for lithium-ion power batteries used in electrical vehicles (EVs) or hybrid electrical vehicles (HEVs) because the high voltage plateau at around 4.7 V makes its energy density (658 Wh kg^?1) 30 and 25 % higher than that of conventional pristine spinel LiMn₂O₄ (440 Wh kg^?1) or olivine LiFePO₄ (500 Wh kg^?1) materials, respectively. Unfortunately, LiNi_0.5Mn_1.5O₄-based batteries with LiPF₆-based carbonate electrolytes always suffer from severe capacity deterioration and poor thermostability because of the oxidization of organic carbonate solvents and decomposition of LiPF₆, especially at elevated temperatures and water-containing environment. The major goal of this review is to highlight the recent advancements in the development of advanced electrolytes for improving the cycling stability and rate capacity of LiNi_0.5Mn_1.5O₄-based batteries. Finally, an insight into the future research and further development of advanced electrolytes for LiNi_0.5Mn_1.5O₄-based batteries is discussed.     

Effect of passivating Al<Subscript>2</Subscript>O<Subscript>3</Subscript> thin films on MnO<Subscript>2</Subscript>/carbon nanotube composite lithium-ion battery anodes

MnO₂/carbon nanotube composite electrodes for Li-ion battery application were directly coated with ultrathin thicknesses of aluminum oxide film by atomic layer deposition (ALD). The non-reactive Al₂O₃ layer not only provides a stable film to protect the manganese oxide and carbon nanotubes from undesirable reaction with the electrolyte but also restrains the volume change strain of manganese oxide during cycling. The first cycle Coulombic efficiency of coated samples was increased to different extents depending on the coating thickness. In the following cycles, the coated electrodes denote high specific capacity, good capacity retention ability, and perfect rate charge/discharge performance.     

Synthesis of hierarchical Na<Subscript>2</Subscript>FeP<Subscript>2</Subscript>O<Subscript>7</Subscript> spheres with high electrochemical performance via spray drying

Hierarchical Na₂FeP₂O₇ spheres with nanoparticles were successfully fabricated by a facile spray drying method. A relatively low drying temperature was introduced in order to form a carbon layer on the surface. As a cathode material for sodium-ion batteries, it delivered a reversible capacity of 84.4 mAh g^?1 at 0.1 C and showed excellent cycling and rate performance (64.7 mAh g^?1 at 5 C). Furthermore, a full sodium battery was fabricated using SP-Na₂FeP₂O₇ as the cathode and hard carbon as the anode, suffering almost no capacity loss after 400 cycles at 1 C. Due to its superior electrochemical property and the low materials cost, Na₂FeP₂O₇ is becoming a promising cathode material for large-scale energy storage systems.     

Electrochemical properties of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> prepared with tartaric acid chelating agent

Lithium manganese oxide (LiMn₂O₄) has been prepared using sol-gel technique under acidic (pH = 5.8) and alkaline (pH = 9) conditions with tartaric acid as chelating agent. X-ray studies show that under acidic condition, an Mn₂O₃ peak was observed indicating the presence of impurities. No impurity was observed for LiMn₂O₄ under alkaline conditions. The particle size is mostly in the range of 124 to 185 nm from HR-TEM. The lithium diffusion coefficient, D _Li+ in LiMn₂O₄ is of the order 10^?9 cm² s^?1. By using density functional theory (DFT) calculations, structural properties have been obtained. The specific discharge capacity of the cells with LiMn₂O₄ prepared under alkaline condition and with LiMn₂O₄ prepared under acidic condition discharged at 0.5 C is in the ranges of 132 to 142 and 128 to 139 mAh g^?1, respectively.     

Nano Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> as sulfur host for high-performance Li-S battery

S/Li₄Ti₅O₁₂ cathode with high lithium ionic conductivity was prepared for Li-S battery. Herein, nano Li₄Ti₅O₁₂ is used as sulfur host and fast Li⁺ conductor, which can adsorb effectively polysulfides and improve remarkably Li⁺ diffusion coefficient in sulfur cathode. At 0.5 C, S/Li₄Ti₅O₁₂ cathode has a stable discharge capacity of 616 mAh g^?1 at the 700th cycle and a capacity loss per cycle of 0.0196% from the second to the 700th cycle, but the corresponding values of S/C cathode are 437 mAh g^?1 and 0.0598%. Even at 2 C, the capacity loss per cycle of S/Li₄Ti₅O₁₂ cathode is only 0.0273% from the second to the 700th cycle. The results indicate that Li₄Ti₅O₁₂ as the sulfur host plays a key role on the high performance of Li-S battery due to reducing the shuttle effect and enhancing lithium ionic conductivity.     

One-step solid-state synthesis of nanosized LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material with power properties

A simple one-step solid state reaction way of preparing nanosized LiMn₂O₄ powders with high-rate properties is investigated. Oxalic acid is used as a functional material to lose volatile gases during the process of calcining in order to control the morphology and change the particle size of materials. The results of X-ray diffraction and scanning electron microscopy show that particle size of materials decreases with the increase of the oxalic acid content. The electrochemical test results indicate that optimal LiMn₂O₄ particles (S_0.5) is synthesized when the molar ratios of oxalic acid and total Mn source are 0.5:1. It also manifests that LiMn₂O₄ sample with middle size has the optimal electrochemical performance among five samples instead of the smallest LiMn₂O₄ sample. The obtained sample S_0.5 with middle size exhibits a high initial discharge capacity of 125.8 mAh g^?1 at 0.2C and 91.4% capacity retention over 100 cycles at 0.5C, superior to any one of other samples. In addition, when cycling at the high rate of 10C, the optimal S_0.5 in this work could still reach a discharge capacity of 80.8 mAh g^?1. This observation can be addressed to the fact that the middle size particles balance the contradictory of diffusion length in solid phase and particle agglomeration, which leads to perfect contacts with the conductive additive, considerable apparent Li-ion diffusion rate, and the optimal performance of S_0.5.     

Nanoporous carbon microspheres as matrix of sulfur to prepare sulfur/carbon cathode material for lithium–sulfur battery

A high specific surface area (2798.8 m² g^?1) of nanoporous carbon microsphere (NPCM) is prepared by activated carbon microsphere in hot CO₂ atmosphere, which is used as matrix material of sulfur to prepare NPCM/sulfur composite cathode material by a melt-diffusion method. The NPCM/sulfur composite cathode material with the sulfur content of 53.5% shows high discharge capacity; the initial discharge capacity is 1274 mAh g^?1 which maintains as high as 776.4 mAh g^?1 after 50 cycles at 0.1 C current. At high current density of 1 C, the NPCM/sulfur cathode material still shows initial discharge capacity of 830.3 mAh g^?1, and the reversible capacity retention is 78% after 50 cycles. To study the influence of different sulfur content of NPCM/sulfur cathode material to the performance of Li–S battery, the different sulfur content of NPCM/sulfur composite cathode materials is prepared by changing the thermal diffusion time and the ratio of sulfur powder to NPCM. The performance of NPCM/sulfur cathode material with different sulfur content is studied at a current of 0.1 C, which will be very important to the preparation of high-performance sulfur/carbon cathode material with appropriate sulfur content.