Extraction And Spectrophotometric Determination Of Cadmium Based On The Formation Of A Ternary Complex With Cadion And 1, 10-Phenanthroline

Abstract

Cadmium ion reacts with cadion and 1, 10-phenanthroline to form a 1:1:2 orange-red ternary complex in 0.5N sodium hydroxide medium. The complex is extracted by chloroform and has a molar absorptivity of 9.2 × 10⁴ l. mole^?1. cm^?1 at 490 nm. A method is developed for the determination of cadmium in electroplating waste water.     

镉试剂正负峰加和法测定水中镉

研究了表面活性剂对Cd(Ⅱ)与1-(4-硝基苯基)-3-(4-苯基偶氮苯基)-三氮烯(镉试剂)显色反应的影响。实验结果表明,在非离子表面活性剂TritonX-100存在下,配合物出现正负两个最大吸收峰分别为478 nm和566 nm。采用正负峰加和法,Cd(Ⅱ)在0~8μg/25 mL范围内服从比尔定律,表观摩尔吸光系数为2.44×105L.mol-1.cm-1。该法可用于合成样品及池塘水样中痕量镉的测定。     

The determination of cadmium in microgram amounts of pancreatic tissue by electrothermal atomic absorption spectometry

Cadmium was determined either by direct insertion of freeze-dried biological samples (1–13 μg) or by injection of 2-μl samples of perifusion medium into the graphite furnace. At 228.8 nm ? 10 fmol of cadmium could be measured. The endogenous cadmium contents in the endocrine and exocrine parts of the pancreas were 8.5 ± 2.0 and 15.1 ± 1.4 μ mol (dry wt.), respectively. A less sensitive wavelength (326.1 nm) was employed for measuring the larger amounts obtained after specimens had been incubated in the presence of cadmium.     

Determination of nanogram amounts of cadmium in water by electrothermal atomic absorption spectrometry after flotation separation

A method is described for the flotation an determination of ng-levels of cadmium in water. Cadmium in a 1-l sample of water is coprecipitated with hydrated zirconium oxide at pH 9.1 ± 0.1. The precipitate is floated with the aid of a surfactant solution and small air bubbles, separated and dissolved in dilute hydrochloric acid. The cadmium content is determined by electrothermal atomic absorption spectrophotometry. The method is applied to the determination of ng l^?1 levels of cadmium in fresh water. The time required for preconcentration of cadmium from a 1-l sample is 20 min per sample, after 20 min stirring.     

HNO3-H2O2反萃取-火焰原子吸收法测定高盐废水中的镉

为解决实际生产中高盐废水中镉的测定,将一定体积的高盐废水加硝酸、高氯酸于电热板消解,消解完全后用APDC(吡咯二硫代氨基甲铵)在pH=3.0条件下与样品中镉生成螯合物,再用四氯乙烯萃取高盐废水消解液中APDC与镉生成的螯合物,继而用硝酸-过氧化氢混合液将有机相中的镉反萃取至水相,最后后用火焰原子吸收光谱法在检测波长228.8nm处测定镉的含量。结果显示10%高盐废水样品5次测定的相对标准偏差为1.1%~5.6%,加标回收的回收率为95%~110%。     

Indirect spectrophotometric determination of cyanide by means of the colour reaction of silver with cadion 2B in presence of triton X-100

Silver gives a colour reaction with cadion 2B in the presence of the non-ionic surfactant Triton X-100, and the suppression of the colour by competitive complexation of the silver can be used for the spectrophotometric determination of cyanide. Cyanide in waste water can be separated by distillation from other ions that also interfere, and then determined.     

Indirect atomic-absorption determination of boron by solvent extraction as tris(1,10-phenanthroline)cadmium tetrafluoroborate

An indirect atomic-absorption method for boron has been developed. Boric acid is converted into tetrafluoroborate and extracted into nitrobenzene with Tris(1,10-phenanthroline)cadmium(II). The cadmium in the extract is determined by its atomic-absorption at 228s>d8 nm. A fivefold molar excess of the cadmium chelate is necessary for the extraction from pH 4>d3-6>d0 medium. The sensitivity for boron is thus made about the same as that of cadmium, 0>d005 ppm. Metal ions that react with fluoride or phenanthroline interfere. A procedure is described for determination of boron in steel.     

微波等离子体炬发射光谱法测定镉的研究

本文提出了一种灵敏测定痕量镉的微波等离子体炬发射光谱法(MPTAES)。探讨了微波等离子体炬(MPT)光源的一些基本特性.采用电热蒸发微量进样装置进样,详细考察了各种实验参数对测定镉的影响.在228.8nm处测定镉,检出限为0.28ng/mL.实际样品的测定结果是令人满意的.     

Spectrophotometric determination of manganese with 1-(2-pyridylazo)-2-naphthol and a non-ionic surfactant

A spectrophotometric method for the determination of trace amounts of manganese with 1-(2-pyridylazo)-2-naphthol (PAN) is described. The method is based on the measurement of absorbance of the manganese—PAN chelate solubilized with a non-ionic surfactant, Triton X-100. No extraction procedure is required in the method proposed. High concentrations of calcium, aluminium and magnesium do not interfere. The presence of up to 10 ppm of lead can be tolerated. Iron, cadmium, zinc, cobalt and nickel can be effectively masked with potassium cyanide. Beer's law is obeyed up to 2 ppm of manganese. The molar absorptivity of the manganese—PAN chelate found was 4.4 × 10⁴ l. mole ⁻¹. cm⁻¹ at 562 nm. The overall stability constant of Mn(PAN)₂ in 0.4% Triton X-100 medium is 10^16.8.     

Spectrophotometric determination of trace amounts of cadmium in high purity zinc materials with iodide and rhodamine 6G

A highly selective and sensitive spectrophotometric procedure for the determination of cadmium is developed. This is based on the interaction of rhodamine 6G with tetraiodocadmate (II) anion to form a pink product which absorbs maximally at 575 nm that is stable for 24 hr when stabilized with gelatin. Cadmium concentrations as low as 0.01 ppm can be readily determined. The method is precise and has been applied to synthetic sea water samples and high purity zinc materials.     

Structural and optical investigations of SiO2-CdS core-shell particles

Cadmium sulfide nanoparticles (approximately 5 nm), chemically capped using thioglycerol molecules, have been anchored onto silica particles (approximately 80 nm) functionalized with 3-aminopropyltrimethoxysilane. Transmission electron microscopy clearly showed that at a low concentration of cadmium sulfide, nanoparticles were discretely and more or less uniformly attached onto the silica particles. At a high concentration of cadmium sulfide nanoparticles, an approximately 6-nm-thick compact shell of cadmium sulfide was formed on the silica particles. In both cases the nanocrystalline nature of cadmium sulfide particles was preserved, as is evident from X-ray diffraction and optical absorption spectra.     

Simultaneous determination of oxygen and cadmium in cadmium and cadmium compounds

Cadmium and its compounds were analysed for oxygen and cadmium by a modification of the Schütze-Unterzaucher method. Oxygen in some compounds such as cadmium oxide, nitrate and sulphate could not be determined by the usual method. The method of adding carbon was employed for the determination of total oxygen. Total oxygen could be determined by the addition of 5 mg of carbon to a sample boat and heating at 950 degrees . The determination was also carried out by addition of naphthalene (2 mg). It was found that the cadmium powder and cadmium flake used contained ca. 1 and 0.15% oxygen, respectively. Oxygen and cadmium in cadmium and its compounds were simultaneously determined by the addition of 2 mg of naphthalene. Cadmium was determined colorimetrically by use of glyoxal-bis-(2-hydroxyanil). Oxygen and cadmium in the samples could be determined simultaneously with an average error of -0.02 and -0.22%, respectively.     

Extractive photometric determination of zinc traces in water

Summary Traces of zinc in water are determined by extracting diethyldithiocarbamates into chloroform at about p_H 9, and stripping lead, zinc and cadmium with 0.16M hydrochloric acid. The cadmium is masked with iodide and the zinc determined spectrophotometrically with Zincon at 620 nm. Iron is masked with citrate before the extraction.

---

Zusammenfassung Zinkspuren in Wasser werden als Diäthyldithiocarbamat mit Chloroform bei p_H 9 extrahiert. Blei, Zink und Cadmium werden dann mit 0,16-n Salzsäure der Chloroformphase entzogen. Cd wird mit Jodid maskiert und Zink spektrophotometrisch mit Zineon bei 620 nm bestimmt. Eisen wird vor der Extraktion mit Zitrat maskiert.

     

Some azo-dye reagents for the spectrophotometric determination of cadmium

2-[2-(5-Bromopyridyl)azol-4,5-dimethylphenol (BrPDMP) and 2-[2-benzothiazolylazo)-5-dimethylaminophenol (BTADAP) have been synthesised and compared, as reagents for cadmium, with the related dyes BrPADAP and BTDMP. The new dyes both form stable highly coloured 2:1 complexes with cadmium, with molar absorptivities (in o-xylene solution) of 3.8 x 10(4) 1.mole(-1).cm(-1) at 590 nm (BrPDMP) and 4.5 x 10(4) 1.mole(-1).cm(-1) at 600 nm (BTADAP). Cadmium can be determined by extraction under alkaline conditions with a solution of BTADAP in xylene. Beer's law is obeyed up to at least 16 mug of cadmium. A limit of detection of 0.15 mug has been estimated and a coefficient of variation of 3.3% at the 5 mug level was found. The only species which interfere seriously are Co(2+), Ni(2+), and Ca(2+). A 200-fold excess of zinc may be tolerated. The method has been applied to the determination of cadmium in water samples, plant materials and hair. Interferences were overcome by preliminary extraction into Aliquat/carbon tetrachloride. The acid dissociation constant of BTADAP (pK = 9.5) and formation constant of the cadmium-BTADAP complex (log beta = 15.1) have been determined.     

The surfactant-sensitized analytical reaction of niobium with 8-hydroxyquinoline-5-sulphonic acid

Cationic surfactants, such as cetylpyridinium bromide (CPB), sensitize the colour reaction of Nb(V) with 8-hydroxyquinoline-5-sulphonic acid (H(2)L). The formation of a ternary complex of stoichiometry 1:3:3 (Nb-L-CPB) is responsible for the observed enhancement in absorptivity and the quenching in the fluorescence of the Nb-L chelate, when a surfactant is present. The ternary complex exhibits maximum absorption at 383 nm ( = 1.46 +/- 0.01 x 10(4) l.mole(-1).cm(-1)) at pH 5.7, and Beer's law is obeyed up to 6-mug ml Nb concentration. Conditional formation constants of the niobium chelate in the presence and absence of CPB have been determined. On the basis of a detailed spectrophotometric and fluorimetric study the nature of the chromophoric reagent-surfactant interaction and the peculiar features of the sensitization by CPB are discussed.     

Preconcentration and determination of lead(II) by microextraction based on suspended cadion covered zirconia nanoparticles in a surfactant media

We have developed a method for the microextraction of lead(II) ion. It is based on the use of suspended zirconia nanoparticles modified with the reagent cadion. Pb(II) ions in the sample are adsorbed onto the modified zirconia nanoparticles suspended in the solution of a non-ionic surfactant. After cloud formation and phase separation by sedimentation, the surfactant rich phase was acidified and diluted to 100 μL with 3.0 mol L^?1 nitric acid and ultrasonicated for a few seconds to desorb the analyte from the sorbent. The mixture was centrifuged and 10 μL of the supernatant liquid phase along with 10 μL of the Pd/Mg modifier were submitted to the electrothermal atomic absorption spectrometer. The parameters affecting the extraction efficiency were optimized by the univariable method. Under the optimized conditions, a sample volume of 40 mL resulted in an enhancement factor of 384 and a detection limit (defined as 3S_b/m) of 2.2 ng L^?1. The method was successfully applied to the determination of Pb(II) in water, tea and rice samples. Accuracy was determined by the recovery experiments and the analysis of two certified reference materials.

Molecular emission cavity analysis : Part VII. The determination of cadmium

Cadmium salts give an intense cadmium atomic emission in the MECA cavity in a hydrogen-nitrogen-air flame. When a carbon or stainless steel cavity is used, 10–120 ng of cadmium in 5-μl samples can be determined. In the presence of sulphuric acid, anionic interferences are removed. Of the cations, only Fe(III), Cr(III), Mg and Sn(II) interfere seriously.     

Cloud Point Extraction and Flame Atomic Absorption Spectrometric Determination of Cd(II) in Industrial and Environmental Samples

A micelle-mediated separation/preconcentration technique was used for the determination of trace Cd(II) in solid and liquid samples by flame atomic absorption spectrometry. Cadmium ions reacted with ammonium pyrrolidine dithiocarbamate to form a chelate that was extracted from aqueous medium by a non-ionic surfactant Tergitol NP-7 at pH 7. Values of pH, concentrations of ammonium pyrrolidine dithiocarbamate and Tergitol NP-7, temperature, incubation time, sample volume and matrix ions were optimized. The enrichment factor of the method was found to be 25, and the detection and quantitation limits were 1.5 and 3.8 μg/L, respectively. Assessment of the method was performed with a certified reference material, and the observed concentration of Cd(II) was in good agreement with the certified value. The method was also applied to the determination of Cd(II) in waters and industrial samples. Cd(II) concentrations in two industrial ZnO composite samples were determined between 59 and 69 μg/g.     

Determination of trace cadmium in waters by flame atomic absorption spectrophotometry after preconcentration with 1-nitroso-2-naphthol-3,6-disulfonic acid on Ambersorb 572

A procedure for the determination of trace amount of cadmium after adsorption of its 1-nitroso-2-naphthol-3,6-disulfonic acid chelate on Ambersorb 572 has been proposed. This chelate is adsorbed on the adsorbent in the pH range 3-8 from large volumes of aqueous solution of water samples with a preconcentration factor of 200. After being sorbed, cadmium was eluted by 5 mL of 2.0 mol L(-1) nitric acid solution and determined directly by flame atomic absorption spectrophotometery (FAAS). The detection limit (3sigma) of cadmium was 0.32 microg L(-1). The precision of the proposed procedure, calculated as the relative standard deviation of recovery in sample solution (100 mL) containing 5 microg of cadmium was satisfactory (1.9%). The adsorption of cadmium onto adsorbent can formally be described by a Langmuir equation with a maximum adsorption capacity of 19.6 mg g(-1) and a binding constant of 6.5 x 10(-3) L mg(-1). Various parameters, such as the effect of pH and the interference of a number of metal ions on the determination of cadmium, have been studied in detail to optimize the conditions for the preconcentration and determination of cadmium in water samples. This procedure was applied to the determination of cadmium in tap and river water samples.