Rapid spectrophotometric determination of thorium(IV) with 1-(2′-thiazolylazo)-2-naphthol

Thorium(IV) reacts with 1-(2-thiazolylazo)-2-naphthol (TAN) in the presence of antipyrine to form a sparingly soluble red-coloured chelate, soluble in 36% methanol (v/v). Complexation takes place instantaneously at pH 2.4–2.8, maintained by glycine buffer. Antipyrine is found to enhance sensitivity of the complex, which is stable for 19 hours. The 12 complex exhibits maximum absorbance at 555 nm, obyes Beer's law in the concentration range from 0.32 to 6.56 g of thorium(IV) per ml, has a molar absorptivity of 3.14·10⁴ dm³/mol^–1·cm^–1 and a Sandel sensitivity of 7.4 ng·cm^–2. The formation constant (log K) is found to be 8.62 and 8.45. Interference of 57 anions and cations in the determination of thorium(IV) has been studied. From ten repeated determinations, the coefficient of variation was found to be ±0.98%. The method was successfully applied for determination of thorium content in a sample of monazite.     

Co-crystallization with 1-(2-pyridylazo)-2-naphthol, and X-ray fluorescence, for trace metal analysis of water

Adding 20mg of 1-(2-pyridylazo)-2-naphthol (PAN) to a water sample at 70°, and filtering off the precipitate after cooling, gives efficient preconcentration prior to X-ray fluorescence analysis of water. Up to the capacity of about 100 μeq of PAN used, the trace metal recoveries are around 90% or higher for Cr³⁺, Mn²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Hg²⁺ and Eu³⁺, and above 70% for many other ions. The recovery yields usually do not vary critically with pH in the neutral pH-range, and are practically independent of the sample salinity, sample volume and trace-metal concentration. Enrichment factors as high as 2 × 10⁵ can be achieved. Counting statistics would then allow detection limits of 0.03 ppM. The blank levels in commercial PAN, however, lead to typical detection limits of about 1 ppm. The coefficient of variation is typically in the 5–10% range at the 10-ppM level. The accuracy and applicability of the procedure are illustrated by comparative analyses on samples of synthetic solutions, river and drinking water.     

Preconcentration neutron activation analysis of trace elements in seawater by coprecipitation with 1-(2-thiazolylazo)-2-naphthol,pyrrolidinedithiocarbamate and N-nitroso-phenylhydroxylamine

A method has been developed for the simultaneous preconcentration of Cd(II), Co(II), Cu(II), Hg(II), Mn(II), Th(IV), U(VI), V(IV) and Zn(II) from 500–1000 ml of water samples by coprecipitation using a combination of 1-(2-thiazolylazo)-2-naphthol, ammonium pyrrolidinedithiocarbamate and ammonium salt of N-nitroso-phenylhydroxylamine. The elemental contents have been measured by neutron activation analysis using different schemes of irradiation, decay and counting periods. Quantitative recoveries of all the above elements have been achieved between pH 6.0 and 7.2. For most of the elements, the enrichment factors are of the order of 10⁴. The precision, expressed in terms of relative standard deviation, and accuracy of measurements are within ±5–10%. The detection limits are in the ppb range. The method has been applied to sea and drinking water samples and biological materials.     

Energy dispersive X-ray fluorescence (EDXRF) determination of lanthanides after preconcentration on 1-(2-pyridylazo)-2-naphthol modified naphthalene

A method is described for the simultaneous multielement determination of yttrium and lanthanides at microgram level. This is based on the preconcentration of these lanthanides on to 1-(2-pyridylazo)-2-naphthol (PAN) modified naphthalene. The optimal conditions for quantitative preconcentration viz., pH, amount of PAN modified naphthalene, time of stirring and aqueous phase volume were systematically evaluated. The quantitation of lanthanides was carried out by energy dispersive X-ray fluorescence analyzer, employing²⁴¹Am annular source, via their characteristic K X-rays. The developed procedure gave reliable results in the analysis of xenotime samples.     

Simultaneous spectrophotometric determination of cobalt,copper and nickel using 1-（2-thiazolylazo）-2-naphthol by chemometrics methods

The simultaneous determination of cobalt, copper and nickel using 1-（2-thiazolylazo）-2-naphthol （first figure of this article） by spectrophotometric method is a difficult problem in analytical chemistry, due to spectral interferences. By multivariate calibration methods, such as partial least squares （PLS） regression, it is possible to obtain a model adjusted to the concentration values of the mixtures used in the calibration range. Orthogonal signal correction （OSC） is a preprocessing technique used for removing the information unrelated to the target variables based on constrained principal component analysis. OSC is a suitable preprocessing method for PLS calibration of mixtures without loss of prediction capacity using spectrophotometric method. In this study, the calibration model is based on absorption spectra in the 550-750-nm range for 21 different mixtures of cobalt, copper and nickel. Calibration matrices were formed from samples containing 0.05-1.05, 0.05-1.30 and 0.05-0.80 μg·mL^-1 for cobalt, copper and nickel, respectively. The root mean square error of prediction （RMSEP） for cobalt, copper and nickel with OSC and without OSC were 0.007, 0.008, 0.011 and 0.031,0.037, 0.032 μg· mL^-1, respectively. This procedure allows the simultaneous determination of cobalt, copper and nickel in synthetic and real samples and good reliability of the determination was proved.     

Pre-concentration of rare earths using silica gel loaded with 1-(2-pyridylazo)-2-naphthol (PAN) and determination by energy dispersive X-ray fluorescence

The determination of a single rare earth element in a mixture with other species of this family is a very challenging problem in analytical chemistry due to the close similarity of their chemical properties. In this work, a liquid–solid extraction procedure for praseodymium, neodymium, samarium and yttrium mixtures and subsequent determination by energy dispersive X-ray fluorescence spectrometry is described. The pre-concentration procedure, which involves the use of silica modified with 1-(2-pyridylazo)-2-naphthol, permits complete recovery of the rare earths and significant sensitivity enhancement in comparison with direct determination in the aqueous phase. Determinations in quaternary mixtures show typical precisions and accuracies of 3% and 5%, respectively.     

Spectrophotometric determination of rare earth metals with 1-(2-pyridylazo)-2-naphthol

1-(2-Pyridylazo)-2-naphthol (PAN) reacts very sensitively with rare earth metals to form a deep red precipitate in alkaline solution; this can be extracted with ether, except in the case of lanthanum, cerium and scandium. Absorption maxima occur at 530 and 560 mμ. Traces of rare earth metals may be determined in the presence of many foreign metals.     

Multiwavelength spectrophotometric determination of acidity constants of 1-（2-thiazolylazo）-2-naphthol in methanol-water mixtures

The acid-base properties of 1-(2-thiazolylazo)-2-naphthol (TAN) in mixtures of methanol-water at 25℃and an ionic strength of 0.1 mol/L are studied by a multi-wavelength spectrophotometric method.The acidity constants of all related equilibria are estimated using the whole spectral fitting of the collected data to an established factor analysis model DATAN program was used for determination of acidity constants.The corresponding pK_a values in methanol-water mixtures were determined.There is a linear relationship between acidity constants and the mole fraction of methanol in the solvent mixtures.     

Spectrophotometric determination of uranium(VI) with 1-(2′-thiazolylazo)-2-naphthol in the presence of Trition X-100

Uranium(VI) reacts with 1-(2-thiazolylazo)-2-naphthol to form a red-coloured chelate in the pH range 5.3–7.2, maintained by 0.04 M acetate buffer. Absorbance of the sparingly soluble complex, solubilized and stabilized by Triton X-100, is measured after 30 min and it is stable for at least 16 hours. The complex exhibits maximum absorbance at 575 and 625–630 nm, but absorbance at longer wavelengths is not stable. The 12 complex obeys Beer's law over the concentration range 0.4–6.4 g of uranium(VI) per cm³, has molar absorptivity 3.36·10⁴ dm³·mol^–1·cm^–1, Sandell sensitivity 7.0 ng·cm^–2, formation constant (log K) 9.32 and coefficient of variation ±0.77%. Effect of 60 ions has been studied and selectivity improved considerably in presence of CDTA. The method has been applied for determination of uranium content in a rock sample.     

Use of 1-(2-thiazolylazo) 2-naphthol in rapid determination of iron in geological matrices

The present work describes the use of 1-(2-thiazolylazo)-2-naphthol (TAN) as a spectrophotomeric reagent for iron determination. TAN reacts with iron(II) forming a brown complex with absorption maximum at 575 and 787 nm. The following parameters were studied: complex stability, pH effect, amount of the TAN, buffer selection, amount of acetate buffer, reductor effect, order of addition of reagents and adherence to Beer's Law. The results demonstrated that iron can be determined with TAN in a pH range of 4.0-6.2 with an apparent molar absorptivity of 1.83 x 10(4) 1 . mol(-1) . cm(-1) (at 787 nm) and 1.41 x 10(4) 1 . mol(-1) . cm(-1) (at 575 nm). Beer's Law is obeyed for at least 3.00 microg/ml. The TAN reacts with other cations, but at 787 nm only the iron(II)-TAN complex absorbs. So, iron can be determined selectively in the presence of several cations. A procedure based on the direct mixture of the sample and a chromogenic solution is proposed, where iron can be determined rapidly and easily. Such procedures were used for the determination of iron in several geological matrices. No significant differences were obtained for TAN method and certificate results.     

A chelating resin containing 1-(2-thiazolylazo)-2-naphthol as the functional group; synthesis and sorption behavior for trace metal ions

A new polystyrene-divinylbenzene resin containing 1-(2-thiazolylazo)-2-naphthol (TAN) functional group was synthesized and its sorption behavior for 19 metal ions including Zr(IV), Hf(IV) and U(VI) was investigated by batch and column experiments. The chelating resin showed a high sorption affinity for Zr(IV) and Hf(IV) at pH 2. Some parameters affecting the sorption of the metal ions are detailed. The breakthrough and overall capacities were measured under optimized conditions. The overall capacities of Zr(IV) and Hf(IV) that were higher than those of the other metal ions were 0.92 and 0.87 mmol/g, respectively. The elution order of metal ions at pH 4 was evaluated as: Zr(IV)>Hf(IV)>Th(IV)>V(V)>Nb(V)>Cu(II)>U(VI)>Ta(V)>Mo(VI)>Cr(III)>Sn(IV)>W(VI). Quantitative recovery of most metal ions except Zr(IV) was achieved using 2 M HNO₃. Desorption and recovery of Zr(IV) was successfully performed with 2 M HClO₄ and 2 M HCl.     

Rapid simultaneous analysis of 1-naphthol and 2-naphthol in water samples by derivative variable-offset synchronous fluorescence spectroscopy

Derivative variable-offset synchronous fluorescence spectroscopy is developed to improve the spectral resolution and the selectivity of fluorescence measurements. 1-naphthol and 2-naphthol are employed to evaluate the proposed coupled technique and the various spectral comparisons are conducted. Second derivative variable-offset synchronous scanning permits the rapid simultaneous identification and quantitative determination of 1-naphthol and 2-naphthol in a mixture from a single spectrum. 6.7-2000 ng/ml 1-naphthol and 3.6-500 ng/ml 2-naphthol can be quantified with 1-naphthol and 2-naphthol ratios of 40: 1-1: 10. The determination of 1-naphthol and 2-naphthol in various spiked water samples gave a mean recovery of 100.7% with a relative standard deviation of 2.8% for 1-naphthol and mean recovery of 99.7% with a relative standard deviation (RSD of 2.6% for 2-naphthol, respectively.     

Determination of seven trace elements in natural waters by neutron activation analysis after preconcentration with 1-(2-pyridylazo)-2-naphthol

A procedure is described for the preconcentration of Cd(I), Co(II), Cr(III), Cu(II), Mn(II), U(VI) and Zn(II) from 800 ml of water and sea-water samples by coprecipitation with 1-(2-pyridylazo)-2-naphthol (PAN) prior to neutron activation. Chromium is reduced to Cr(III) by hydroxylammonium chloride at pH 4 before the preconcentration step. Coprecipitation of 30 mg of PAN was most effective at pH 9 with final recoveries of 76–91% for six elements and 50% for uranium. The scheme is based on double irradiation of the same samples. Short (10 min) irradiation followed by γ-spectrometry counting for 10 min gives data for Cd (^111mCd), Co, Cu, Mn and U (²³⁹U). A second 16-h irradiation permits determination of zinc and uranium (²³⁹Np) after a waiting time of 6 h, cadmium (¹¹⁵Cd) after 24 h and chromium after a waiting period of 2 weeks followed by counting for 30 min. Detection limits are 0.04 ng g^?1 for Co, 0.8 ng g^?1 for Cd, 0.3 ng g^?1 for Cu, 0.2 ng g^?1 for Cr, 0.006 ng g^?1 for Mn, 0.006 ng g^?1 for U and 0.3 ng g^?1 for Zn. A further decrease of the detection limit for chromium to 0.05 ng g^?1 can be achieved by separation of interfering nuclides and scintillation counting of ⁵¹Cr with a NaI(Tl) well-type detector.     

Complexation of uranium by 2-(2-thiazolylazo)-4-methoxyphenol and 2-(2-thiazolylazo)-5-methoxyphenol

A comparative study has been made of the complexation of uranium(VI) by 2-(2-thiazolyl)-4-methoxyphenol (TAMH) and 2-(2-thiazolylazo)-5-methoxyphenol(TAMR). The complexes are less stable and have lower molar absorptivities than the PAR and TAR complexes but are still useful for determination of uranium. The TAMH chelate can be extracted into isobutyl methyl ketone. Both complexes are 1:1 metal :ligand. For the TAMH complex log beta(1) = 8.8, = 1.4 x 10(4) at 610 mmu; for the TAMR complex log beta(1) = 8.1, = 2.0 x 10(4) at 530 mmu.     

Determination of manganese by flame atomic absorption spectrometry after its adsorption onto naphthalene modified with 1-(2-pyridylazo)-2-naphthol (PAN)

A system for determination of manganese, after preconcentration with 3% (w/w) 1-(2-pyridylazo)-2-naphthol (PAN), adsorbed on microcrystalline naphthalene is proposed. An amount of 200 mg of this complexing mixture is placed in a glass column and conditioned with a NH₄Cl/NH₄OH buffer solution (pH 9.5). The aqueous sample, containing manganese, is treated with an ammonium tartrate solution, then with a hydroxylammonium chloride solution and, finally, with a buffer solution. The resulting solution is passed through the column containing microcrystalline naphthalene modified with 1-(2-pyridylazo)-2-naphthol (PAN) where Mn(II) is retained. The column is first washed with deionized water and then with 10.0 ml of dimethylformamide to dissolve the Mn(II)-PAN/naphthalene complex. Manganese is determined by air-acetylene flame atomic absorption spectrometry. About 1 μg of manganese can be concentrated from 200 ml of aqueous sample, allowing a preconcentration factor of 20, a limit of quantification of 5 ng ml⁻¹ and R.S.D. of 3.8%. The accuracy was ascertained using certified reference materials, including samples of urine and glass. Water samples were also analysed and the results are in good agreement with those obtained by graphite furnace atomic absorption spectrometry.     

Rapid spectrophotometric determination of manganese(II) with 4-(2-thiazolylazo)-resorcinol

Summary Manganese forms a red chelate with 4-(2-thiazolylazo)-resorcinol at pH 8.8 (borate buffer), and absorbance is measured after 30 s, at 540 nm in the presence of 20%tert-butyl alcohol (by volume). The 12 complex obeys Beer's law for manganese concentration of 0.04–1.4g per ml, has molar absorptivity 4.176 x 10⁴ and Sandell sensitivity 0.0013g cm^–2. The formation constant (logK) is found to be 9.32, and relative standard deviation ±0.22%. Of the 48 ions studied for interference, only Co(II), Zn(II), Cd(II), Pb(II) and EDTA^2– are found to interfere. This method has been applied for the determination of manganese content in alloy steels.

---

Spektrophotometrische Bestimmung von Mangan(II) mit 4-(2-Thiazolylazo)-resorcin

Zusammenfassung Mangan bildet bei pH 8,8 (Boratpuffer) mit 4-(2-Thiazolylazo)-resorcin ein rotes Chelat, dessen Absorbanz nach 30 sec bei 540 nm in Gegenwart von 20% tert. Butylalkohol gemessen wird. Dieser 12-Komplex entspricht bei einer Mangan-Konzentration von 0,04–1,4g/ml dem Beerschen Gesetz; seine molare Absorption beträgt 4,176 x 10⁴, die Empfindlichkeit nach Sandell 0,0013g·cm^–2. Die Bildungskonstante (log K) beträgt 9,32, die rel. Standardabweichung ±0,22%. Unter 48 untersuchten Ionen erwiesen sich nur Co(II), Zn(II), Cd(II), Pb(II) und EDTA als störend.-Das Verfahren wurde zur Bestimmung des Mangangehaltes in Stahl verwendet.

     

Atomic absorption spectrometric determination of trace zinc in alloys and biological samples after preconcentration with [1-(2-pyridylazo)-2-naphthol] on microcrystalline naphthalene

An atomic absorption spectrometric method for the determination of trace amounts of zinc after adsorption of its [1-(2-pyridylazo)-2-naphthol] complex on microcrystalline naphthalene has been developed. This complex is adsorbed on microcrystalline naphthalene in the pH range 3.5-7.5 from large volumes of aqueous solutions of various alloys and biological samples with a preconcentration factor of 40. After filtration, the solid mass consisting of the zinc complex and naphthalene was dissolved with 5 ml of dimethylformamide and the metal was determined by flame atomic absorption spectrometry. Zinc can alternatively be quantitatively adsorbed on [1-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent packed in a column and determined similarly. About 0.5 ng of zinc can be concentrated in a column from 200 ml of aqueous sample, where its concentration is as low as 2.5 pg ml-1. The calibration curve is linear in the range 0.1-6.5 ng ml-1 in dimethylformamide solution. Eight replicate determinations of 2 ng ml-1 of zinc gave a mean absorbance of 0.145 with a relative standard deviation of 1.5%. The sensitivity for 1% absorption was 0.061 ng ml-1. Various parameters, such as the effect of pH and the interference of a number of metal ions on the determination of zinc, have been studied in detail to optimize the conditions for the determination of zinc in various standard complex materials.