Determination of rubidium, strontium and barium in barite by atomic-absorption spectrometry after dissolution in disodium ethylenediaminetetra-acetate

A simple and rapid method is described for determining up to 50% of barium, approximately 350 mug/g or more of strontium and approximately 1 mug/g or more of rubidium in barite samples. The method involves dissolution of the barite by refluxing with an ammoniacal disodium EDTA solution. For the determination of total strontium and rubidium, the silicate residue remaining is filtered off and decomposed with hydrofluoric and sulphuric acids to recover residual strontium and rubidium. Barium and strontium are subsequently determined by flame atomic-absorption spectrometry and rubidium is determined by graphite-furnace atomic-absorption spectrometry. Results obtained for barium and strontium in several barites by the proposed method are compared with those obtained by wavelength-dispersive and energy-dispersive X-ray fluorescence spectrometry, respectively. The method is reliable and more rapid than conventional methods.     

Preconcentration of trace amounts of manganese from natural waters by means of a macroreticular poly(dithiocarbamate) resin

A chelating poly(dithiocarbamate) resin (PDTC) with macroreticular support is characterized as effective collector for traces of manganese from natural waters. Using small PDTC columns preconcentration of manganese can be achieved even at high flow-rates (5-6 ml/min) and sample volumes (1500 ml). Accordingly, PDTC resin is used for the preconcentration of manganese from water samples prior to its determination by flame atomic-absorption spectrometry. A series of ions abundant in natural waters do not interfere. The sensitivity and detection limit were 2.5 and 0.5 mug/l., respectively. The relative standard deviations of the results for a manganese concentration of 40-400 mug/l. are in the range 1.1-6.2%. In mineral and tap waters analysed, the manganese concentration range was between 2.9 and 30.8 mug/l.     

Determination of mono- and sesquiterpenes in water samples by membrane inlet mass spectrometry and static headspace gas chromatography

A membrane inlet mass spectrometric (MIMS) method is presented and compared with a static headspace gas chromatographic method (HSGC) for the determination of terpenes in water. The MIMS method provides a very simple and fast analysis of terpenes in water, detection limits being relatively low, from 0.2 mug l(-1) for monoterpenes to 2 mug l(-1) for geraniol. The analysis of terpenes by the HSGC (equipped with flame ionization detector, FID) method is more time-consuming and the detection limits (2 mug l(-1) for monoterpenes to 100 mug l(-1) for geraniol) are higher than with MIMS. However, the HSGC method has the advantage of determining individual mono- and sesquiterpene compounds, whereas MIMS provides only separation of different classes of terpenes. Both methods were applied to the analysis of mono- and sesquiterpenes in several condensation water samples of pulp and paper mills.     

Atomic-absorption spectrophotometric determination of traces of manganese with thenoyltrifluoroacetone

An atomic-absorption spectrophotometric method for the determination of traces of manganese in solution with thenoyltrifluoroacetone (TTA) is described. Manganese(II) is extracted with 0.01M TTA in methyl isobutyl ketone (MIBK) at pH 9.5. The atomic-absorption of the organic phase at 279.5 nm is measured. Except for chromium, iron, hafnium, niobium, nickel, rhodium, tin, titanium and zirconium, microquantities of many other cations and anions do not interfere. Iron can be removed by MIBK extraction before the TTA extraction. The sensitivity of the method was 1.6 ng/ml for 1% absorption in aqueous solution. The method was successfully applied to the analysis of environmental waters. Manganese in the filtered fractions of water samples was reliably determined with relative standard deviations of 7% at the 5 mug/l. level and 1% at 50 mug/l.     

Indirect determination of cyanide in water by atomic-absorption spectrophotometry

An indirect method for determination of trace cyanide in water by atomic-absorption spectrophotometry is described. Cyanide forms a stable complex anion with Pd in alkaline solution. This complex anion can form an ion-association complex with tetra-alkylammonium ions which can be extracted into n-butyl alcohol with an efficiency higher than 90%. The extract can be analysed directly for palladium (and hence indirectly for cyanide) by flame atomic-absorption spectrophotometry. The detection limit for cyanide by this method is 0.1 mug ml in the n-butyl alcohol extract. Beer's law is obeyed for 0.13-9 mug of CN(-) per ml of n-butyl alcohol. Several foreign ions do not interfere.     

Rapid determination of zinc and iron in foods by flow-injection analysis with flame atomic-absorption spectrophotometry and slurry nebulization

A rapid method of determining zinc and iron in food by flame atomic-absorption spectrophotometry with slurry nebulization into an air-acetylene flame has been developed. A V-groove, clog-free Babington-type nebulizer, coupled to a single-line flow-injection analysis (FIA) system, was employed to introduce the slurry into the spray chamber. Under the FIA conditions described, an injection frequency of 120/hr is possible, with negligible carry-over and memory effects. The calibration graphs were obtained by using various concentrations (up to 0.1 g/ml) of white bean homogenate as standards, rather than solutions. The method has been applied to various kinds of foods, including grains, vegetables, fruits and sausage. Homogenization of semi-prepared samples to form slurries took only 4 min. Relative deviations between results by the slurry and solution methods for both elements averaged 2-3%. Detection limits by the slurry method were 0.3 mug/ml Zn and 0.6 mug/ml Fe.     

Determination of cadmium, lead and copper in water samples by flame atomic-absorption spectrometry with preconcentration by flow-injection on-line sorbent extraction

Cadmium, lead and copper were determined in synthetic sea-water, drinking water and the NBS 1643b Trace Elements in Water standard reference material at mug/l. levels by flame atomic-absorption spectrometry after on-line preconcentration by sorbent extraction with a flow-injection system. Bonded silica with octadecyl functional groups packed in a micro column of 100 mul capacity was used to collect diethylammonium diethyldithiocarbamate complexes of the heavy metals in the aqueous samples. The sample loading time was 20 sec at a flow-rate of 3.3 ml/min. Ethanol or methanol was used to elute the adsorbed analytes into the spectrometer. The sample loading rate, elution rate and pH were optimized. Enrichment factors of 19-25 for Cd, Pb and Cu were achieved at sampling frequencies of 120/hr with precisions of 1.4, 1.0 and 1.3% rsd (n = 11), respectively. The detection limits (3sigma) for Cd, Pb and Cu were 0.3, 3 and 0.2 mug/l., respectively. Determination of Cd, Pb and Cu in NBS SRM 1643b showed good agreement with the certified values. Recoveries of Cd and Pb added to sea-water were 95 and 102%, respectively.     

Comparison of silver results for canadian reference ores and concentrates and zinc-processing products by acid decomposition, tribenzylamine/chloroform extraction and fire-assay combined with atomic-absorption spectrophotometry

The results obtained for silver in Canadian reference ores and concentrates and in zinc-processing products by three atomic-absorption spectrophotometric methods are compared. "Wet chemical" methods based on the decomposition of the sample with mixed acids yield more accurate results than those based on fire-assay collection techniques. A direct acid-decomposition method involving the determination of silver in a 20% v/v hydrochloric acid-1% v/v diethylenetriamine medium is recommended for the determination of approximately 10 mug g or higher levels of silver. A method based on chloroform extraction of the tribenzylamine-silver bromide ion-association complex from 0.08M potassium bromide-2M sulphuric acid is recommended for samples containing < 10 mug of silver per g.     

Determination of silver in copper and lead metals and alloys and in zinc and selenium by atomic-absorption spectrometry after separation by extraction of the tri-n-octylmethylammonium-silver bromide complex

A simple and sensitive combined solvent extraction and atomic-absorption spectrometric method has been developed for the determination of silver in copper and lead metals and alloys and in zinc and selenium. Optimal conditions have been established for the extraction and determination of silver. Silver is extracted as the tri-n-octylmethylammonium-silver bromide complex and determined by atomic-absorption spectrometry by spraying the extract directly into the flame. As little as 0.2 mug of silver in a sample can be determined.     

Determination of tellurium in copper, lead and selenium by atomic-absorption spectrometry after extraction of the trioctylmethylammonium-tellurium bromide complex

A simple, rapid and sensitive combined solvent extraction and atomic-absorption spectrometric method has been developed for the determination of tellurium in copper, lead, selenium and blister copper. Tellurium is extracted as the trioctylmethylammonium-tellurium(IV) bromide complex into butyl acetate and determined by flame atomic-absorption spectrometry of the extract. As little as 1 mug of tellurium in a sample can be determined. The extraction of tellurium from hydrobromic acid solution with trioctylamine has also been investigated.     

Analysis of sediments for heavy metals by a rapid electrothermal atomic-absorption procedure

A rapid electrothermal atomic-absorption spectrophotometric procedure with homogenization as the only pretreatment is compared with two wet pretreatment methods followed by flame atomic-absorption, in a statistically designed experiment. Samples from the top 5 cm of sediments at three different points of the Tejo estuary were used for the tests. The results show that the electrothermal procedure performed as well as whichever was the better of the flame methods for the determination of cadmium and nickel, irrespective of the sand content of the samples; although not statistically significant, there was apparently a decrease in recovery for chromium, copper and lead by the electrothermal method as the sand content of the sample increased. For zinc the electrothermal method gave results statistically different from those of the flame procedures when the sand content was high but not when the organic content of the sample was high. Because of the limited degree of replication (5 variates) the relative differences between the average values obtained by the three methods were significant only if they exceeded 15%. The electrothermal method has the advantage of substantially greater speed.     

Determination of lead in tooth-pastes by electrothermal atomic-absorption spectrophotometry with platform atomization

Electrothermal atomic-absorption spectrometry is used for the determination of lead in tooth-pastes, by means of the graphite platform/matrix-modification technique. The method is easy to apply, has limited interferences and is more precise than conventional flame AAS. The working concentration range is up to 100 mug/1. The method is characterized by a detection limit of 0.08 mug/1. and a precision of +/-1.9 % for the sample solutions. For the tooth-pastes, the detection limit is between 1.1 and 5.4 ng/g and the precision in the range 1.8-10%.     

Determination of gold in silver, copper, lead, selenium and anode slime by atomic-absorption spectrometry

A simple and sensitive combined solvent-extraction and atomic-absorption spectrometric method has been developed for the determination of gold in silver, copper, lead, selenium and anode slime. Samples are decomposed with hydrochloric and nitric acids, and gold is extracted as the trioctylmethylammonium-gold bromide complex and determined by atomic-absorption spectrometry by direct spraying of the extract into the flame. Optimal conditions for the extraction and determination of gold have been established. As little as 0.5 mug of gold in a sample can be determined. The extraction of gold from hydrochloric or hydrobromic acid solution with trioctylamine or trioctylmethylammonium chloride (or bromide) has also been investigated.     

Application of the slotted quartz tube in flow-injection flame atomic-absorption spectrometry

The slotted quartz has been applied to flow-injection flame atomic-absorption spectrometry (FI-FAAS) showing several important advantages. The tube life was improved by a factor of 5-6 compared to conventional continuous aspiration. Flow impact systems were found not to be necessary in the applications so that larger enhancement factors may be achieved without sacrifice in precision. For 1.0 mg/l. copper, 1.0 mg/l. lead, 0.1 mg/l. cadmium and 1.0 mg/l. gold sensitivity enhancement factors of 3.1, 5.5, 5.3 and 4.0 were obtained with precisions of 1.3%, 1.1%, 1.6% and 1.7% RSD (n = 11) respectively. Application of the slotted quartz tube FI-FAAS method to the determination of heavy metals in urine has shown improved tolerance to interfering matrices. Recoveries obtained by spiking undiluted urine samples with 0.1 mg/l. copper and lead, and 0.01 mg/l. cadmium were in the range 100-102%.     

Rapid analysis of small glass fragments by atomic-absorption spectroscopy

A rapid method is described for the determination of magnesium, iron and manganese in small glass fragments (250-500 mug). The speed of the analytical procedure is made possible by the use of a convenient cold digestion stage allied to a discrete sampling method which permits the three elements of interest to be determined by flame atomic-absorption spectrophotometry.     

An investigation of a flameless atomic-absorption method for determination of aluminium, calcium, iron and magnesium in sewage sludge

The methods currently used for the determination of aluminium, calcium, iron and magnesium in sewage sludge are time-consuming. A rapid flameless atomic-absorption procedure, utilizing homogenization of diluted samples as the only pretreatment, has been compared with wet and dry analytical methods followed by flame atomic-absorption analysis, in a statistically designed experiment. Low-sensitivity (secondary absorption) lines have been used for the flameless analysis. The flameless atomic-absorption method described is better than all the other methods tested, with the exception of the nitric-perchloric-hydrofluoric acid digestion procedure. The time saved is substantial and the method could be used advantageously for routine analysis.     

Direct determination of beryllium, copper and zinc in AlU matrices by electrothermal atomization atomic-absorption spectrometry

An atomic-absorption spectrometric method with electrothermal mode of atomization has been developed for the direct determination of Be, Cu and Zn in AlU (3:1) matrix samples without prior chemical separation of the major matrix. The studies carried out include the effect of the matrix on the analyte absorbance, optimization of sample aliquot and other experimental parameters, and analysis of a number of synthetic samples. Nanogram amounts of the analytes can be determined with a solution aliquot of 5 microlitres containing 25 micrograms of the sample with a precision of 6% or better. The analytical range obtained for these analytes is Be: 2-20 mug/l., Cu: 20-200mug/l. and Zn: 1-40mug/ml in the AlU matrix. The analysis of synthetic samples has shown good agreement with their added contents.     

Determination of cadmium in urine by extraction and flameless atomic-absorption spectrophotometry Comparison of urine from smokers and non-smokers of different sex and age

A method is presented for determining cadmium in urine by nameless atomic-absorption spectrophotometry after extraction. The sample is dried, ashed in the presence of nitric acid, and then the residue is dissolved in hydrochloric acid. Cadmium is extracted as its tetrahexylammonium iodide complex into methyl isobutyl ketone. The organic phase is analysed for cadmium by atomic-absorption spectrophotometry with electrothermal atomization. The median urinary excretion of cadmium for smokers aged 50-64 has been found to be 0.7 and 0.75 mug l . for males and females respectively, the values for non-smokers being 0.25 and 0.4mug l .     

Determination of cobalt, nickel, lead, bismuth and indium in ores, soils and related materials by atomic-absorption spectrometry after separation by xanthate extraction

A method for determining approximately 0.5, mug/g or more of cobalt, nickel and lead and approximately 3 mug/g or more of bismuth and indium in ores, soils and related materials is described. After sample decomposition and dissolution of the salts in dilute hydrochloric-tartaric acid solution, iron(III) is reduced with ascorbic acid and the resultant iron(II) is complexed with ammonium fluoride. Cobalt, nickel, lead, bismuth and indium are subsequently separated from iron, aluminium, zinc and other matrix elements by a triple chloroform extraction of their xanthate complexes at pH 2.00 +/- 0.05. After the removal of chloroform by evaporation and the destruction of the xanthates with nitric and perchloric acids, the solution is evaporated to dryness and the individual elements are ultimately determined in a 20% v/v hydrochloric acid medium containing 1000 mug/ml potassium by atomic-absorption spectrometry with an air-acetylene flame. Co-extraction of arsenic and antimony is avoided by volatilizing them as the bromides during the decomposition step. Small amounts of co-extracted molybdenum, iron and copper do not interfere.     

In Process Citation

Three methods commonly used for copper measurements in the range 0.5-10 mug/l. were compared by statistical analysis of the data. Regression analysis was applied to the calibration curves and confidence intervals were calculated, providing a constant index of precision. The atomic-absorption method seems to be the best choice, especially because it permits much saving of time when several metals are to be determined in the same sample.