Separation of natural antioxidants using PDMS electrophoresis microchips coupled with amperometric detection and reverse polarity

This report describes the use of PDMS ME coupled with amperometric detection for rapid separation of ascorbic, gallic , ferulic, p‐coumaric acids using reverse polarity. ME devices were fabricated in PDMS by soft lithography and detection was accomplished using an integrated carbon fiber working electrode aligned in the end‐channel configuration. Separation and detection parameters were investigated and the best conditions were obtained using a run buffer consisting of 5 mM phosphate buffer (pH 6.9) and a detection voltage of 1.0 V versus Ag/AgCl reference electrode. All compounds were separated within 70 s using gated injection mode with baseline resolution and separation efficiencies between 1200 and 9000 plates. Calibration curves exhibited good linearity and the LODs achieved ranged from 1.7 to 9.7 μM. The precision for migration time and peak height provided maximum values of 4% for the intrachip studies. Lastly, the analytical method was successfully applied for the analysis of ascorbic and gallic acids in commercial beverage samples. The results achieved using ME coupled with amperometric detection were in good agreement with the values provided by the supplier. Based on the data reported here, the proposed method shows suitability to be applied for the routine analysis of beverage samples.     

Isocratic ion chromatographic determination of underivatized amino acids by electrochemical detection

An isocratic chromatographic separation with amperometric detection of underivatized amino acids at a copper oxyhydroxide modified glassy carbon electrode is described. A simple and sensitive quantitation procedure of amino acids without the need of tedious and time-consuming derivatization step was achieved by coupling anion-exchange chromatography with electrochemical detection. The effects of hydroxide, nitrate and acetonitrile concentration in the mobile phase on the capacity factors and peak resolution was evaluated. Under the optimized isocratic chromatographic conditions (i.e. 60 mM NaOH) and under constant applied potentials (i.e. 0.55 V versus Ag/AgCl) the detection limit ranged between 4 and 24 pmol injected and the linear dynamic range spanned generally over three or four order of magnitude for all investigated amino acid compounds. Direct determination of several common free amino acids in beer and milk samples were performed.     

Preparation of multiwall carbon nanotubes film modified electrode and its application to simultaneous determination of oxidizable amino acids in ion chromatography

A multiwall carbon nanotubes (MWNTs) film modified electrode was prepared and used as an amperometric sensor for the simultaneous determination of oxidizable amino acids including cysteine, tryptophane and tyrosine. The electrochemical behaviors of these amino acids at this modified electrode were studied by cyclic voltammetry (CV). The results indicated that the MWNTs chemically modified electrode (CME) exhibited efficient electrocatalytic activity towards the oxidation of these amino acids with relatively high sensitivity, stability and long-life. Following separation by ion chromatography (IC) with 2.0×10⁻³ mol l⁻¹ citric acid buffer solution (pH 6.5) as eluent, cysteine, tryptophane and tyrosine could be determined by the MWNTs CME successfully. Under the optimal conditions, the detection limits were 7.0×10⁻⁷ mol l⁻¹ for cysteine, 2.0×10⁻⁷ mol l⁻¹ for tryptophane and 3.5×10⁻⁷ mol l⁻¹ for tyrosine at the signal-to-noise of 3, respectively. The method was applied successfully to the determination of these substances in plasma.     

Simultaneous Determination of Carbohydrates and Amino Acids by Capillary Zone Electrophoresis with Constant Potential Amperometric Detection at a Copper Electrode

Capillary zone electrophoresis with end-column amperometric detection at a copper microdisk electrode (100 μm in diameter) was successfully applied for simultaneous determination of carbohydrates and amino acids. Under the separation voltage of 27 kV and the separation electrolyte of 80 mM NaOH in a 75 cm fused silica capillary (10 μm i.d. × 375 μmU o.d.), complete separation of a standard mixture containing 9 carbohydrates and 12 amino acids was achieved in less than 25 min. With the electrokinetical injection of 5.4 s at 27 kV and the detection potential of 0.62 V vs. Ag/AgCl, the detection limits (S/N = 3) were 0.22–0.65 ppm (1.2–1.9 μM) for carbohydrates and 0.31–6.5 ppm (2.3–39 μM) for amino acids, respectively. The calculated numbers of theoretical plates were between 41,000 and 190,000. The use of this method for analysis of carbohydrates and amino acids in a urine sample was demonstrated.     

Determination of active constituents in Lonicera confusa DC. by capillary electrophoresis with amperometric detection

A method based on capillary electrophoresis with amperometric detection has been developed for the determination of luteolin, chlorogenic acid, 3,5-dicaffeoylquinic acid and caffeic acid in the dried flower buds, leaves and stems (three medicinal parts) of Lonicera confusa DC., respectively. The effects of several important factors such as detection potential, the concentration of the running buffer, separation voltage and injection time were investigated to acquire the optimum conditions. The detection electrode was a 300 microm diameter carbon disc electrode at a working potential of + 0.90 V (vs saturated calomel electrode). The four analytes can be well separated within 10 min in a 40 cm-long fused silica capillary at a separation voltage of 12 kV in a 50 mM borate-25 mM phosphate buffer (pH 8.0). The relationship between peak current and analyte concentration was linear over about 3 orders of magnitude with detection limits (S/N = 3) ranging from 0.35 to 0.52 microM for all analytes. The proposed method has been successfully applied to the monitoring of bioactive constituents in the real plant samples with satisfactory assay results.     

Capillary electrophoresis-amperometric determination of antioxidant propyl gallate and butylated hydroxyanisole in foods.

Capillary electrophoretic separation coupled with end-column amperometric detection for the simultaneous quantification of butylated hydroxyanisole (BHA) and propyl gallate (PG) in food was developed. Important factors affecting separation and detection, such as the running buffer, separation voltage, and detection potential, were investigated in detail. An improved working electrode preparation method was used, where a carbon disk of 33 microm in diameter was sealed in a tip and positioned opposite the outlet of a capillary. The experiments indicated that the preparation method was simple, and the obtained electrode exhibited good flexibility and stability for the determination of phenolic antioxidants. The separation was carried out within 5 min using a 50 cm length capillary, with a solution containing 5 mM phosphate and 5 mM borax of pH 8.84 as a separation buffer, and a separation potential of 20 kV. Amperometric detection was achieved with an applied potential of 0.70 V versus Ag|AgCl| saturated KCl. There was excellent linearity between the peak current and the concentrations of the analytes in the range of 1.8 - 180.2 microg/mL for BHA and 10.6 - 212.2 microg/mL for PG, respectively. Relative standard deviations of 4.92% for BHA and 5.27% for PG were obtained, respectively. The developed method was successfully applied for the determination of antioxidants in several commercial foods.     

Quantitation of caffeine by capillary zone electrophoresis with end-column amperometric detection at a carbon microdisk array electrode

Capillary zone electrophoresis is employed for the determination of caffeine using end-column amperometric detection with a carbon fiber microdisk array electrode at a constant potential of 1.45 V versus a saturated calomel electrode. The optimum conditions of separation and detection are 0.1 52mM NaH2PO4-0.648mM Na2HPO4 for the buffer solution, 20 kV for the separation voltage, 5 kV for the injection voltage, and 10s for the injection time. The limit of detection is 2.9 x 10(-4)mM or 1.2 fmol (signal-to-noise ratio = 2). The relative standard deviation is 0.68% for the migration time and 2.3% for the electrophoretic peak current. The method is applied to determining caffeine in human serum and a cola drink.     

Microchip capillary electrophoresis with amperometric detection for rapid separation and detection of phenolic acids

A microchip capillary-electrophoresis protocol for rapid and effective measurements of food-related phenolic acids (including chlorogenic, gentisic, ferulic, and vanillic acids) is described. Relevant parameters of the chip separation and amperometric detection are examined and optimized. Under optimum conditions, the analytes could be separated and detected in a 15 mM borate buffer (pH 9.5, with 10% of methanol) within 300 s using a separation voltage of 2000 V and a detection voltage of +1.0 V. Linear calibration plots are observed for micromolar concentrations of the phenolic acid compounds. The negligible sample volumes used in the microchip procedure obviates surface fouling common to amperometric measurements of phenolic compounds. The new microchip protocol offers great promise for a wide range of food applications requiring fast measurements and negligible sample consumption. An application on a commercial red wine was performed with minimal sample preparation and promising results.     

Determination of hydrazine, monomethylhydrazine, 1,1-dimethylhydrazine, and 1,2-dimethylhydrazine by nonaqueous capillary electrophoresis with amperometric detection

The present study is concerned with the application of nonaqueous capillary electrophoresis (NACE) with electrochemical detection (ED) to the separation and quantitative determination of hydrazine (Hy) and its methyl derivatives. The best performance of NACE-ED was found when using 4 mM sodium acetate/10 mM acetic acid/methanol: acetonitrile = 1:2 as the running buffer, with a bare platinum working electrode set at +1.0 V in an end-column amperometric detection cell. The choice and ratio of suitable solvents for the separation and injection media played an essential role for the performance characteristics of the method. The limits of detection for Hy, methylhydrazine, symmetrical dimethylhydrazine, and unsymmetrical dimethylhydrazine were 5, 2, 12, and 1 ng/mL, respectively. This is between one and two orders of magnitude lower than that achieved by previously reported CE-ED methods in aqueous buffer systems in conjunction with various types of chemically modified electrodes. The practical utility of the new NACE-ED methodology is demonstrated in terms of the determination of traces of Hys in spiked environmental samples containing a wide range of explosives and related compounds.     

A new method of quantification of pipemidic-acid by capillary zone electrophoresis with end-column amperometric detection

Capillary zone electrophoresis was employed for the determination of pipemidic acid using an end-column amperometric detection with a carbon fiber microdisk array electrode, at a constant potential of -1.10 V vs. saturated calomel electrode. The optimum conditions of separation and detection were 1.2 x 10(-4) mol/LNaOAc - 8.8 x 10(-4) mol/ LHOAc for the buffer solution, 20 kV for the separation voltage, 5 kV and 10 s for the injection voltage and the injection time. The limit of detection was 1.05 x 10(-7) mol/L or 189 amol (S/N=3). The relative standard deviation was 0.31% for the migration time and 2.0% for the electrophoretic peak current. The method was applied to determining pipemidic acid in human serum.     

A dynamically modified microfluidic poly(dimethylsiloxane) chip with electrochemical detection for biological analysis

Separation and direct detection of amino acids, glucose and peptide in a 3.1 cm separation channel made of poly(dimethylsiloxane) (PDMS) with end-column amperometric detection at a copper microdisk electrode was developed. This system is the integration of a normal sized working electrode with electrochemical detection on a PDMS microfabricated device. The PDMS channels dynamically modified by 2-morpholinoethanesulfonic acid (MES) show less adsorption and more enhanced efficiency than that of unmodified ones when applied to separations of these biological molecules. The migration time is less than 100 s and the reproducibility of migration time is satisfactory with relative standard deviation (RSD) of 2.8% in 19 successive injections. The limits of detection of arginine (Arg), glucose, and methionine-glycine (Met-Gly) are estimated to be 2.0, 8.5, and 64.0 microM at S/N = 3, approximately 0.5-16.0 fmol, respectively. Variances influencing the separation efficiency and amperometric response, including injection, separation voltage, detection potential, or concentration of buffer and additive, are assessed and optimized.     

Amperometric determination of underivatized amino acids at a nickel-modified gold electrode by anion-exchange chromatography

A nickel-based composite electrode obtained by anodic electrodeposition of nickel (III) oxyhydroxide film on the gold electrode substrate was characterized as an amperometric sensor and successfully applied to the determination of underivatised amino acids in flow-through systems. The electrodeposition of nickel oxyhydroxide films was obtained by cycling a gold electrode between 0.0 V and +1.0 V vs. a saturated calomel electrode in a 80 microM Ni2+ solution buffered at pH 10 with NaHCO3/Na2CO3. The resulting Au-Ni composite electrode exhibits good stability in alkaline medium and can be used as an amperometric sensor of underivatised amino acids at a fixed applied potential (+0.55 V vs. Ag/AgCl). The detection limits (S/N=3) for all investigated compounds ranged between 5 and 30 pmol injected, while the linear ranges spanned over two or three orders of magnitude. The contents of several free amino acids in two sample cheeses from different brands were evaluated by calibration graphs.     

Determination of electroactive organic acids by anion-exchange chromatography using a copper modified electrode

An ion-chromatographic method combined with electrochemical detection at a copper-based chemically modified glassy carbon electrode (Cu-GC) has been shown to provide a simple analytical approach for the determination of some common organic acids in alkaline medium. Under the optimized isocratic chromatographic conditions (i.e. 0.1 M NaOH plus 80 mM CH3COONa), organic acids such as gallic, ascorbic, gluconic, lactobionic, galacturonic and glucuronic acid could be separated in less than 20 min. Under constant potential amperometric detection (i.e. 0.55 V vs. Ag-AgCl) the Cu-GC modified electrode allowed detection limits between 2 and 5 pmol for all investigated organic acids while the linear dynamic range spanned generally over three orders of magnitude. Examples of applications included the separation and quantitation of some common organic acids in vinegar, honey and tea samples, are given.     

Determination of amino acids in tobacco samples by capillary electrophoresis/indirect absorbance detection with isolation of the electrolysis compartment and p-Aminobenzoic acid as a background electrolyte.

A fast, convenient and sensitive method of capillary zone electrophoresis (CZE) and indirect UV detection was proposed for the determination of 16 amino acids. p-Aminobenzoic acid (PAB) was selected as a background electrolyte (BGE). An isolated cell included a BGE buffer part and an electrode buffer one, which were jointed with a glass frit. The isolated cell can prevent PAB from the electrode reaction and improve the stability of the detection baseline. The separation conditions of amino acids were investigated, such as different BGEs, BGE concentration, buffer pH and electroosmotic flow (EOF) modifiers. Under the selected separation conditions, 14 amino acid peaks could be separated in 12 min. The detection limits of the amino acids were in the range of 1.7 - 4.5 micromol/L. The isolated cell is suitable for reagents reacting on the electrodes in capillary electrophoresis. The proposed method has been successfully applied to the determination of the amino acids in tobacco samples.     

Microchip capillary electrophoresis with a cellulose-DNA-modified screen-printed electrode for the analysis of neurotransmitters

A microfluidic chip based on capillary electrophoresis coupled with a cellulose-single-stranded DNA (cellulose-ssDNA) modified electrode was used for the simultaneous analysis of dopamine (DA), norepinephrine (NE), 3,4-dihydroxy-L-phenylalanine (L-DOPA), 3,4-dihydroxyphenylacetic acid (DOPAC), and ascorbic acid (AA). The modification of the electrode improved the electrophoretic analysis performance by lowering the detection potential and enhancing the signal-to-noise characteristic without surface poisoning of the electrode. The sensitivity of the modified electrode was about 12 times higher than those of the bare ones. The test compounds were separated using a 62 mm long separation channel at the separation field strength of +200 V/cm within 220 s in a 10 mM phosphate buffer (pH 7.4). The most favorable potential for the amperometric detection was 0.7 V (vs. Ag/AgCl). A reproducible response (relative standard deviation of 1.3, 1.3, 2.1, 3.1, 3.4% for DA, NE, L-DOPA, DOPAC, and AA, respectively, for n = 9) for repetitive sample injections reflected the negligible electrode fouling at the cellulose-ssDNA modified electrode. Square-wave voltammetric analyses reflected the sensitivities of the modified electrode for DA, NE, L-DOPA, DOPAC, and AA which were 1.78, 0.82, 0.69, 2.45, and 1.23 nC/microM with detection limits of 0.032, 0.93, 1.13, 0.31, and 0.62 microM, respectively. The applicability of this microsystem to real sample analysis was demonstrated.     

Capillary electrophoresis of nonprotein and protein amino acids without derivatization

An efficient separation of eleven nonprotein amino acids (NPAAs) and three protein amino acids containing aromatic moieties was achieved by capillary electrophoresis without derivatization. The fourteen amino acids were well separated with a 100 mM sodium phosphate run buffer (pH 2.0) using a 57 cm fused-silica capillary (50 microm ID, 50 cm effective length) at 20 degrees C. With an electric field of 351 V/cm, the time needed for the separation was less than 20 min. Under optimum conditions, excellent linear responses were obtained in the concentration range of 5-100 microM, with the linear correlation coefficient ranging from 0.9785 or greater. The relative standard deviations of the migration times and the corrected peak areas were found to be 1.5-3.9% and 8.0-11.5%, respectively. In order to improve the limit of detection (LOD), simple stacking and large volume stacking using an EOF pump (LVSEP) methods were used. Improved LODs were about 300 nM in stacking and below 15 nM for five small NPAAs in LVSEP.     

Performance of throughout in-capillary derivatization capillary electrophoresis employing an on-line sample and run buffer loading device

We report on the effect on performance of varying the length of the capillary during throughout in-capillary derivatization (TICD) capillary electrophoresis (CE). Performance was evaluated by on-line coupling with a sample and CE runbuffer loading device that was newly introduced for this study. The device was assembled with a low cost using two 5 mm inner diameter (ID) disposable polyethylene syringes. First, a sequence was manually formed consisting of a 200 microL run buffer solution plug, a 100 microL sample plug and another 200 microL run buffer solution plug. Each plug was separated from its neighbor by a 100 microL air plug. When each plug reached the injection point where both a platinum-wire anode and the end of the separation capillary tube were located, 340 V/cm separation voltage (electrophoresis voltage) and 34 V/cm injection voltage were applied to the capillary for 3 s. Then the analytes were derivatized during migration in 50 microm ID capillaries filled with 2 mM o-phthalaldehyde (OPA)/N-acetylcysteine (NAC) in a 20 mM phosphate-borate buffer (pH 10), followed by separating and detecting of OPA derivatives by absorbance of 340 nm. Derivatization, separation, and detection were performed systematically using capillaries which varied in length from 5 to 80 cm. In the case of TICD-CE of a mixture containing 1 mM aspartic acid (Asp) and 20 mM m-nitorophenol (MNP) as a test solution, it was determined that peak area and peak width ratios of Asp to MNP did not depend on capillary length. Enantiomeric separations of DL-alanine (Ala) and Asp were examined using a run buffer consisting of a 45 microM beta-cyclodextrin (CD)-2 mM OPA/NAC-20 mM phosphate-borate buffer (pH 10). Even though the resolution of these enantiomeric pairs decreased with decreasing capillary length, as expected, the peaks corresponding to both enantiomeric amino acids were identified even when a 5 cm capillary was used. An 8-component amino acid mixture was also tested with 5 cm and 10 cm capillaries.     

A three-dimensionally adjustable amperometric detector for microchip electrophoretic measurement of nitroaromatic pollutants

A microchip capillary electrophoresis (CE)–amperometric detection (AD) system has been fabricated by integrating a two-dimensionally adjustable CE microchip and an amperometric detection cell containing a one-dimensionally adjustable disc detection electrode in a Plexiglas holder. It facilitates the precise three-dimensional alignment between the channel outlet and the detection electrode without a complicated three-dimensional manipulator. The performance of this unique system was demonstrated by separating four nitroaromatic pollutants (nitrobenzene, 2,4-dinitrotoluene, 2,4,6-trinitrotoluene, and p-nitrobenzene). Factors influencing their separation and detection processes were examined and optimised. The four analytes have been well-separated within 120 s in a 75 cm long separation channel at a separation voltage of +2000 V using an electrophoretic separation medium containing 15 mM borax and 15 mM sodium dodecyl sulfate (pH 9.2). Highly linear response is obtained for the four analytes over the range of 0–5 ppm with the detection limits ranging from 12 to 52 ppb. The present system demonstrated long-term stability and reproducibility with relative standard deviations of less than 5% for the peak current (n = 9). The new approach for the microchannel–electrode alignment should find a wide range of applications in other microfluidic analysis systems.     

Operational parameters of voltammetric high-performance liquid chromatographic detectors with copper electrodes and application to a determination of some fodder biofactors

Two versions of an amperometric detector with a copper working electrode have been constructed and tested for high-performance liquid chromatography (HPLC). The performance of the detectors was studied using selected amino acids. The dependence of the detector response on the mobile phase flow-rate was studied in the range common in both macro- and microcolumn HPLC (5 microliter/min to 1.0 ml/min). It has been found that the detection sensitivity generally increases with decreasing flow-rate, i.e., the detector response is governed by the rate of the complexation reaction between the cupric ions and the solutes. This fact makes amperometric detection with a copper electrode especially useful for microcolumn separations. For all 20 amino acids studied, calibration curve parameters and detection limits have been determined; the latter vary from 0.4 to 18 ng in the injected volume. The amino acids can also be sensitively detected in a medium of 0.1-1.0 M ammonia, which is promising for the use of strong anion exchangers in amino acid separations. Choline can also be detected at a copper electrode, with a detection limit of 40 ng. An HPLC method with amperometric detection at a copper electrode has been developed for the determination of lysine, methionine and choline in fodder biofactors.     

采用隔离池的毛细管电泳-间接紫外吸收法测定茶叶中的氨基酸

改进的毛细管电泳-间接紫外吸收法采用了自制隔离池,以对氨基苯甲酸(PAB)为背景电解质,对茶叶中的氨基酸进行了测定。PAB能够提高分离效率,降低检出限。隔离池的使用避免了PAB的电极反应,降低了基线噪声,维持了两缓冲液池间的电流导通。研究了背景电解质的浓度、pH值以及电渗流改性剂的种类和浓度对氨基酸分离的影响。在优化的实验条件下,16种氨基酸在14 min内达到了基线分离,峰面积的相对标准偏差小于5%(n=5),检出限为1.7~4.5 μmol/L,回收率为83.0%~106%。该法快速、便捷和灵敏,已成功应用于茶叶中11种游离氨基酸的检测。