A novel H2O2 sensor based on the enzymatically induced deposition of polyaniline at a horseradish peroxide/aligned single-wall carbon nanotubes modified Au electrode

A novel H(2)O(2) sensor based on enzymatically induced deposition of electroactive polyaniline (PANI) at a horseradish peroxide (HRP)/aligned single-wall carbon nanotubes (SWCNTs) modified Au electrode is fabricated, and its electrochemical behaviors are investigated. Electrochemical impedance spectroscopy of the sensor confirmed the formation of PANI on SWCNTs through the HRP catalytic reaction. Cyclic voltammograms of PANI/HRP/SWCNTs modified Au electrodes showed a pair of well-defined redox peaks of PANI with reduction peak potentials of 0.211 and oxidation peak potentials of 0.293 V in 0.1 M HOAc-NaOAc (pH 4.3) solution. The oxidation peak current response of PANI is linearly related to H(2)O(2) concentration from 2.5 μM to 50.0 μM with a correlation coefficient of 0.9923 and a sensitivity of 200 μA mM(-1). The detection limit is determined to be 0.9 μM with a signal-to-noise ratio of 3. Thus, the synergistic performance of the enzyme, the highly efficient polymerization of PANI, and the templated deposition of SWCNTs provided an extensive platform for the design of novel electrochemical biosensors.     

纳米Pt/巯基丁二酰胺铜修饰电极的制备及其电催化活性

利用电沉积法将纳米Pt固定在巯基丁二酰胺铜(II)自组装金电极(Au/CuL)表面, 制备了一种纳米催化电极(Au/CuL/nano Pt). 分别以扫描电子显微镜(SEM)、原子力显微镜(AFM)、光电子能谱(XPS), 表面红外光谱(FT-IR)及电化学交流阻抗(EIS)对电极表面形貌进行了表征, 并采用循环伏安法(CV)研究了它的电化学性质. 结果表明, CuL具有良好的电化学活性并对H2O2的还原具有电催化作用, 纳米Pt可以显著增强这种催化性能. 在30 ℃、0.02 mol·L-1 PBS缓冲液(pH=6.0)中检测H2O2, 在0.00125-0.16 mmol·L-1浓度范围呈现线性响应, 相关系数为0.9960(信噪比为3), 检测极限为0.3 μmol·L-1. 该电极对H2O2电流响应灵敏度高(0.312 mA·cm-2·mmol-1·L)、检测迅速(4.3 s)、稳定性好(对46 μmol·L-1和2.8 mmol·L-1的H2O2连续测10 次, 变异系数分别为3.1%和3.9%; 保存70 d后对10 μmol·L-1 H2O2的响应为初始响应的95%).     

Enzymatic deposition of Au nanoparticles on the designed electrode surface and its application in glucose detection

This paper reported the enzymatic deposition of Au nanoparticles (AuNPs) on the designed 3-mercapto-propionic acid/glucose oxidase/chitosan (MPA/GOD/Chit) modified glassy carbon electrode and its application in glucose detection. Chit served as GOD immobilization matrix and interacted with MPA through electrostatic attraction. AuNPs, without nano-seeds presented on the electrode surface, was produced through the glucose oxidase catalyzed oxidation of glucose. The mechanism of production of AuNPs was confirmed to be that enzymatic reaction products H(2)O(2) in the solution reduce gold complex to AuNPs. The characterizations of the electrode modified after each assembly step was investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Scanning electron microscopy showed the average particle size of the AuNPs is 40nm with a narrow particle size distribution. The content of AuNPs on the electrode surfaces was measured by differential pulse stripping voltammetry. The electrochemical signals on voltammogram showed a linear increase with the glucose concentration in the range of 0.010-0.12mM with a detection limit of 4μM. This provided a method to the determination of glucose.     

An Electrochemical Sensor Based on Gold Nanoparticles Incorporated in Mesoporous MFI Zeolite for Determination of Purine Bases in DNA

An electrochemical sensor was developed based on gold nanoparticles incorporated in mesoporous MFI zeolite for the determination of purine bases. Au nanoparticles (AuNPs) were incorporated into the mesoporous MFI zeolite (AuNPs/m‐MFI) by post‐grafting reaction. The composite materials were characterized by transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS) and electrochemical methods. Au nanoparticles with a size of 5‐20 nm are uniformly dispersed in the pores of mesoporous MFI zeolite. And the morphology of MFI zeolite can be perfectly kept after pore expansion and Au nanoparticles incorporation. The electrocatalytic oxidation of purine bases (guanine and adenine in DNA) is investigated by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The surface‐confined Au nanoparticles provide the good catalytic activity for oxidation of purine bases. The simultaneous detection of guanine and adenine can be achieved at AuNPs/m‐MFI composites modified glassy carbon electrode (GCE). The electrochemical sensor based on AuNPs/m‐MFI exhibits wide linear range of 0.5–500 μM and 0.8–500 μM with detection limit of 0.25 and 0.29 μM for guanine and adenine, respectively. Moreover, the electrochemical sensor is applied to evaluation of guanine and adenine in herring sperm DNA samples with satisfactory results.     

A novel dinuclear Schiff-base copper(II) complex modified electrode for ascorbic acid catalytic oxidation and determination

A new dinuclear copper salicylaldehyde-glycine Schiff-base complex [Cu(2)(Sal-Gly)(2)(H(2)O)(2)] was synthesized and structurally characterized. [Cu(2)(Sal-Gly)(2)(H(2)O)(2)] crystallized in the monoclinic system in the P2(1)/c space group. The molecule is a dinuclear complex, formed by two [Cu(Sal-Gly)(H(2)O)] units. The electropolymerization properties of the copper complex on a glass carbon electrode were studied at different potential ranges. The electropolymerization occurred when the high scan potential reached 1.4 V. The modified electrode exhibited good electrocatalytic oxidation properties to ascorbic acid and showed a sensitivity of 22.9 nA μM(-1) (r(2) = 0.9998) and detection limit of 0.39 μM (S/N = 3) in the amperometric determination of ascorbic acid. The designed determination method can be used to analyze vitamin C tablets.     

Development of an amperometric sulfite biosensor based on a gold nanoparticles/chitosan/multiwalled carbon nanotubes/polyaniline-modified gold electrode

A sulfite oxidase (SOx) purified from leaves of Syzygium cumini (Jamun) was immobilized covalently onto a gold nanoparticles (AuNPs)/chitosan (CHIT)/carboxylated multiwalled carbon nanotubes (cMWCNTs)/polyaniline (PANI) composite that was electrodeposited onto the surface of a gold (Au) electrode. A novel and highly sensitive sulfite biosensor was developed that used this enzyme electrode (SOx/AuNPs/CHIT/cMWCNT/PANI/Au) as the working electrode, Ag/AgCl as the standard electrode, and Pt wire as the auxiliary electrode. The modified electrode was characterized by Fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy (EIS) before and after the immobilization of the SOx. The sensor produced its optimum response within 3 s when operated at 50 mVs⁻¹ in 0.1 M phosphate buffer, pH 7.0, and at 35 °C. The linear range and detection limit of the sensor were 0.75–400 μM and 0.5 μM (S/N = 3), respectively. The biosensor was employed to determine sulfite levels in fruit juices and alcoholic beverages. The enzyme electrode was used 300 times over a period of three months when stored at 4 °C.     

Highly sensitive determination of hydroxylamine using fused gold nanoparticles immobilized on sol-gel film modified gold electrode

We are reporting the highly sensitive determination of hydroxylamine (HA) using 2-mercapto-4-methyl-5-thiazoleacetic acid (TAA) capped fused spherical gold nanoparticles (AuNPs) modified Au electrode. The fused TAA-AuNPs were immobilized on (3-mercaptopropyl)-trimethoxysilane (MPTS) sol-gel film, which was pre-assembled on Au electrode. The immobilization of fused TAA-AuNPs on MPTS sol-gel film was confirmed by UV-vis absorption spectroscopy and atomic force microscopy (AFM). The AFM image showed that the AuNPs retained the fused spherical morphology after immobilized on sol-gel film. The fused TAA-AuNPs on MPTS modified Au electrode were used for the determination of HA in phosphate buffer (PB) solution (pH = 7.2). When compared to bare Au electrode, the fused AuNPs modified electrode not only shifted the oxidation potential of HA towards less positive potential but also enhanced its oxidation peak current. Further, the oxidation of HA was highly stable at fused AuNPs modified electrode. Using amperometric method, determination of 17.5 nM HA was achieved for the first time. Further, the current response of HA increases linearly while increasing its concentration from 17.5 nM to 22 mM and a detection limit was found to be 0.39 nM (S/N = 3). The present modified electrode was also successfully used for the determination of 17.5 nM HA in the presence of 200-fold excess of common interferents such as urea, NO₂⁻, NH₄⁺, oxalate, Mn²⁺, Na⁺, K⁺, Mg²⁺, Ca²⁺, Ba²⁺ and Cu²⁺. The practical application of the present modified electrode was demonstrated by measuring the concentration of HA in ground water samples.     

Synthesis, characterization, and electrochemiluminescence of luminol-reduced gold nanoparticles and their application in a hydrogen peroxide sensor

It was found that chloroauric acid (HAuCl(4)) could be directly reduced by the luminescent reagent luminol in aqueous solution to form gold nanoparticles (AuNPs), the size of which depended on the amount of luminol. The morphology and surface state of as-prepared AuNPs were characterized by transmission electron microscopy, UV/visible spectroscopy, X-ray photoelectron spectroscopy, FTIR spectroscopy, and thermogravimetric analysis. All results indicated that residual luminol and its oxidation product 3-aminophthalate coexisted on the surface of AuNPs through the weak covalent interaction between gold and nitrogen atoms in their amino groups. Subsequently, a luminol-capped AuNP-modified electrode was fabricated by the immobilization of AuNPs on a gold electrode by virtue of cysteine molecules and then immersion in a luminol solution. The modified electrode was characterized by cyclic voltammetry, electrochemical impedance spectroscopy, and scanning electron microscopy. The as-prepared modified electrode exhibited an electrochemiluminescence (ECL) response in alkaline aqueous solution under a double-step potential. H2O2 was found to enhance the ECL. On this basis, an ECL sensor for the detection of H2O2 was developed. The method is simple, fast, and reagent free. It is applicable to the determination of H2O2 in the range of 3x10(-7)-1x10(-3) mol L(-1) with a detection limit of 1x10(-7) mol L(-1) (S/N=3).     

Mercury‐modified Lignosulfonate‐stabilized Gold Nanoparticles as an Alternative Material for Anodic Stripping Voltammetry of Thallium

Lignosulfonate‐stabilized gold nanoparticles (AuNPs‐LS) were synthesized and subsequently used as a complexing agent for mercury ions. The obtained AuNPs‐LS/Hg²⁺ complex was characterized by means of various physicochemical techniques such as UV‐vis spectroscopy, transmission electron microscopy and cyclic voltammetry. Furthermore, the resulting complex was evaluated as an electrode modifier for the development of amperometric sensors. Upon sufficient negative potential, the bound mercury ions are reduced to form an amalgam with AuNPs‐LS. Thus, the performance of glassy carbon electrode (GCE) modified by AuNPs‐LS/Hg film was investigated as an electrochemical sensor in the determination of Tl⁺ ions in a 0.05 M EDTA at pH 4.5. The presence of the mercury containing film improves the analyte accumulation due to its ability to form a fused amalgam with thallium. The presented data indicate that the GCE/AuNPs‐LS/Hg modified electrode shows better performance toward Tl⁺ determination in comparison to bare GCE. The stripping anodic peak current of thallium was linear over its concentration range from 1.7⋅10⁻⁷ to 5.0⋅10⁻⁶ M. The detection limit (3σ) was estimated to be 1.4⋅10⁻⁷ M. The proposed method was successfully applied for the determination of thallium ions in real samples of soil derived from the area of the copper smelter near Głogów (Poland).     

A catechol biosensor based on a gold nanoparticles encapsulated-dendrimer

Tyrosinase has been immobilized on a Au nanoparticles encapsulated-dendrimer bonded conducting polymer on a glassy carbon electrode for the estimation of catechol. The modified electrode was characterized by cyclic voltammetry and AFM techniques. The principle of catechol estimation was based on the reduction of biocatalytically liberated quinone species at +0.2 V versus Ag/AgCl (3 M KCl), with good stability, sensitivity, and featuring a low detection limit (about 0.002 μM) and wide linear range (0.005 μM-120 μM). The electrochemical redox peak of catechol on the GCE/PolyPATT/Den(AuNPs)/tyrosinase was also investigated. A response time of 7 s, reusability up to 5 cycles and a shelf life of more than 2 months under refrigerated conditions were reported. Various parameters influencing biosensor performance have been optimized including pH, temperature, and applied potential. The utility and application of this nanobiosensor was tested in a real water samples.     

A sensitive and selective nitrite sensor based on a glassy carbon electrode modified with gold nanoparticles and sulfonated graphene

We describe a highly sensitive and selective amperometric sensor for the determination of nitrite. A glassy carbon electrode was modified with a composite made from gold nanoparticles (AuNPs) and sulfonated graphene (SG). The modified electrode displays excellent electrocatalytic activity in terms of nitrite oxidation by giving much higher peak currents (at even lower oxidation overpotential) than those found for the bare electrode, the AuNPs-modified electrode, and the SG-modified electrode. The sensor has a linear response in the 10 μM to 3.96 mM concentration range, a very good detection sensitivity (45.44 μA mM^?1), and a lower detection limit of 0.2 μM of nitrite. Most common ions and many environmental organic pollutants do not interfere. The sensor was successfully applied to the determination of nitrite in water samples, and the results were found to be consistent with the values obtained by spectrophotometry.

Simultaneous electrochemical determination of hydrazine and nitrite based on Au nanoparticles decorated on the poly(Nile Blue) modified carbon nanotube

In this study, simultaneous determination of toxic hydrazine and nitrite was performed on composite electrodes of poly(Nile blue)(NB), carbon nanotube(CNT) and gold nanoparticles(AuNPs). The prepared AuNPs/CNT/poly(NB)/GCE was used for as a sensor platform for individual and simultaneous determination of hydrazine and nitrite. Electrodes were characterized by HRTEM, SEM, XPS, EIS. The LOD for nitrite and hydrazine was 5.0 μM and 3.1 μM at AuNP/CNT/poly(NB)/GCE, respectively. Also, sensitive amperometric determinations of hydrazine and nitrite were performed and LOD were calculated as 0.33 μM and 0.68 μM, respectively. The method was applied to sausage and river water samples and recovery results were obtained in the range 85–115 %.     

Fast batch injection analysis of H(2)O(2) using an array of Pt-modified gold microelectrodes obtained from split electronic chips

A fast and robust analytical method for amperometric determination of hydrogen peroxide (H(2)O(2)) based on batch injection analysis (BIA) on an array of gold microelectrodes modified with platinum is proposed. The gold microelectrode array (n=14) was obtained from electronic chips developed for surface mounted device technology (SMD), whose size offers advantages to adapt them in batch cells. The effect of the dispensing rate, volume injected, distance between the platinum microelectrodes and the pipette tip, as well as the volume of solution in the cell on the analytical response were evaluated. The method allows the H(2)O(2) amperometric determination in the concentration range from 0.8 μmolL(-1) to 100 μmolL(-1). The analytical frequency can attain 300 determinations per hour and the detection limit was estimated in 0.34 μmolL(-1) (3σ). The anodic current peaks obtained after a series of 23 successive injections of 50 μL of 25 μmolL(-1) H(2)O(2) showed an RSD<0.9%. To ensure the good selectivity to detect H(2)O(2), its determination was performed in a differential mode, with selective destruction of the H(2)O(2) with catalase in 10 mmolL(-1) phosphate buffer solution. Practical application of the analytical procedure involved H(2)O(2) determination in rainwater of S?o Paulo City. A comparison of the results obtained by the proposed amperometric method with another one which combines flow injection analysis (FIA) with spectrophotometric detection showed good agreement.     

Application of Carbon Paste Electrode Modified with Carbon Nanofibres/Polyaniline/Platinum Nanoparticles as an Electrochemical Sensor for the Determination of Bezafibrate

The present study deals with the development of an electrochemical sensor for quantitative determination of Bezafibrate (BZF) based on carbon nanofibers/polyaniline/platinum nanoparticles modified carbon paste electrode (CNF/PANI/Pt/CPE). BZF is a fibric acid derivative and is used largely in the treatment of lipid disorders. The nanocomposite was synthesized by in situ polymerization of aniline using ammonium persulphate and platinum nanoparticles were uniformly decorated on the CNF/PANI surface by reducing hexachloroplatinic acid using sodium borohydride. The electrochemical response of BZF at CNF/PANI/Pt/CPE was studied using cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). The above study resulted into significant improvement of the electrochemical signal towards the oxidation of BZF, revealing that the oxidation process is highly favorable at the surface of modified electrode. The anodic peak current I_p (μA) is found to be linearly dependent on BZF concentration in the range of 0.025 μM to 100 μM with a detection limit of 2.46 nM. The practical analytical utilities of the sensor were investigated by performing the experiments on synthetic pharmaceutical formulations, human blood serum and urine samples which offered good recovery, suggesting the high efficacy and authenticity of CNF/PANI/Pt/CPE sensor for BZF determination.     

Mb/AuNPs/MWCNTs/GC电极对H2O2电催化性能的研究

采用还原法制备了AuNPs/MWCNTs复合材料,并构建了氧化还原蛋白质的固定化和生物传感界面AuNPs/MWCNTs/GC电极.以肌红蛋白(Myoglobin,Mb)为例,研究了固定化蛋白质在AuNPs/MWCNTs/GC电极上的直接电化学.结果表明,AuNPs/MWCNTs复合材料不仅能有效地促进Mb与电极表面的直接电子转移,而且能很好地保持固定化Mb的生物催化活性.Mb/AuNPs/MWCNTs/GC电极对H2O2具有良好的电催化还原性能,其线性响应范围为1～138μmol·L-1,检测限为0.32μmol·L-1(S/N=3),并具有较低的米氏常数(0.143 mmol·L-1).该电极操作简单,响应迅速,稳定性和重现性好,有望用于蛋白质的固定化及第三代生物传感器的制备.     

Electrochemical Surface Structuring with Polyaniline Wrapped Hb for Hydrogen Peroxide Biosensing

Through the electrodeposition of aniline with hemoglobin (Hb) on zincoxide‐gold colloidal sols (ZnO‐AuNPs) modified indium oxide electrode, a hydrogen peroxide (H₂O₂) biosensor was constructed. Polyaniline (PANI) form a nano‐cage wrapped Hb, which provided a comfortable and stable site for the immobization of Hb. UV‐vis spectrum was employed to characterize Hb retained original structure in the resulting Hb‐PANI/ZnO‐AuNPs membrane. Electrochemical investigation of the biosensor showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa= ‐0.139 V and E_pc = ‐0.238 V (vs. SCE) in 0.1 M pH 7.0 phosphate buffer solution at the scan rate of 100 mV/s. The biosensor displayed a fast response time (<3 s) and broad linear response to H₂O₂ in the range from 1.5 μM to 1.7 mM with a detection limit of 0.8 μM (S/N = 3).     

An amperometric horseradish peroxidase inhibition biosensor for the determination of phenylhydrazine

An amperometric horseradish peroxidase (HRP) inhibition biosensor has been substantially constructed by the help of N,N-dicyclohexylcarbodiimide (DCC), N-hydroxysuccinimide (NHS). The preparation steps and the biosensor response to phenylhydrazine were monitored by electrochemical impedance spectroscopy (EIS), cyclic voltammetry, and chronoamperometry. The proposed biosensor could be applied to determine phenylhydrazine in a 0.10 M phosphate buffer solution containing 1.2 mM hydroquinone and 0.50 mM H(2)O(2) by phenylhydrazine, inhibiting the catalytic activity of the HRP enzyme in the reduction of H(2)O(2). The system was optimized to realize a reliable determination of phenylhydrazine in the range of 2.5 x 10(-7) to 1.1 x 10(-6) M with a detection limit of 8.2 x 10(-8) M and a correlation coefficient of 0.999. The modified electrode displayed good reproducibility, sensitivity and stability for the determination of phenylhydrazine.     

Electrochemical Fabrication of Prussian Blue Nanocube‐decorated Electroreduced Graphene Oxide for Amperometric Sensing of NADH

In this study, Prussian blue (PB) film on the electroreduced graphene oxide (ERGO)‐modified Au electrode surface (ERGO/PB) is easily prepared by means of cyclic voltammetric technique in the mixture of K₃Fe(CN)₆ and FeCl₃. Its electrochemical behaviors for NADH biosensor are studied. The structural and morphological characters of modified electrode material are analyzed with using of XPS, XRD, Raman, EDS, and SEM techniques. ERGO/PB hybrid nanocomposite for NADH biosensor is exhibited to the higher catalytic effect (linear range from 1.0 to 100 μM, detection limit of 0.23 μM at S/N=3) compared to naked Au, ERGO‐modified Au, and PB‐modified Au electrodes. In addition to, ERGO/PB electrode was used to voltammetric and amperometric detection of H₂O₂. ERGO/PB electrodes also showed the same behavior as the NADH sensor. This ERGO/PB‐modified electrode supplied a simple, new, and low‐cost route for amperometric sensing of both NADH and H₂O₂.     

Selective determination of 3,4-dihydroxyphenylacetic acid in the presence of ascorbic acid using 4-(dimethylamino)pyridine capped gold nanoparticles immobilized on gold electrode

4-(Dimethylamino)pyridine capped gold nanoparticles (DMAP-AuNPs) were synthesized in aqueous medium and then immobilized on 1,6-hexanedithiol (HDT) modified Au electrode for the selective determination of 3,4-dihydroxyphenylacetic acid (DOPAC) in the presence of ascorbic acid (AA). The synthesized DMAP-AuNPs were characterized by UV-visible spectroscopy and high resolution-transmission electron microscopy (HR-TEM). The HR-TEM images showed that the nanoparticles are spherical in shape with a diameter of ～12 nm. The DMAP-AuNPs immobilized on HDT modified electrode was characterized by cyclic voltammetry and impedance spectroscopy. Impedance spectra show that the electron transfer reaction was more facile at the AuNPs modified electrode when compared to bare and HDT modified Au electrodes. The application of DMAP-AuNPs modified electrode was demonstrated by selective determination of DOPAC in the presence of high concentration of AA at pH 4. Using amperometry method, 40 nM detection of each AA and DOPAC was achieved. The current response was increased linearly with increasing AA and DOPAC in the concentration range of 40×10(-9) to 10×10(-5) M and a detection limit was found to be 5.6×10(-10) M and 3.7×10(-10) M (S/N=3) for AA and DOPAC, respectively. The present modified electrode was also successfully used for the determination of 40 nM DOPAC in the presence of 2500-fold excess of common interferents such as Na(+), Mg(2+), Cu(2+), Ca(2+), NH(4)(+) urea and glucose.     

Fabrication of multiwalled carbon nanotubes/polyaniline modified Au electrode for ascorbic acid determination

An ascorbate oxidase (AsOx) (E.C.1.10.3.3) purified from Lagenaria siceraria fruit was immobilized covalently onto a carboxylated multiwalled carbon nanotubes and polyaniline (c-MWCNT/PANI) layer electrochemically deposited on the surface of an Au electrode. The diffusion coefficient of ascorbic acid was determined as 3.05 × 10(-4) cm(2) s(-1). The behavior of different electrolytes on electro-deposition was also studied. An ascorbate biosensor was fabricated using a AsOx/c-MWCNT/PANI/Au electrode as a working electrode, Ag/AgCl (3 M/saturated KCl) as standard and Pt wire as an auxiliary electrode connected through a potentiostat. Linear range, response time and detection limit were 2-206 μM, 2 s and 0.9 μM respectively. The biosensor showed optimum response at pH 5.8 and in a broader temperature range (30-45 °C), when polarized at +0.6 V. The biosensor was employed for determination of ascorbic acid level in sera, fruit juices and vitamin C tablets. The sensor was evaluated with 91% recovery of added ascorbic acid in sera and 6.5% and 11.4% within and between batch coefficients of variation respectively for five serum samples. There was a good correlation (r = 0.98) between fruit juice ascorbic acid values by the standard 2,6-dichlorophenolindophenol (DCPIP) method and the present method. The enzyme electrode was used 200 times over a period of two months, when stored at 4 °C. The biosensor has advantages over earlier enzyme sensors in that it has no leakage of enzyme, due to the covalent coupling of enzyme with the support, lower response time, wider working range, higher storage stability and no interference by serum substances.