Identification of the oxidation products of the reaction between alpha-pinene and hydroxyl radicals by gas and high-performance liquid chromatography with mass spectrometric detection

In this paper an identification method is described for determining the degradation products of the reaction of alpha-pinene with hydroxyl radicals. The study is carried out in a fast-flow reactor equipped with a specially designed microwave cavity (type Surfatron) allowing to operate at pressures up to 100 Torr (1 Torr=133.322 Pa). The semivolatile products are collected on a liquid nitrogen trap (LN2 trap) and the batch samples are subsequently analysed by GC-MS and HPLC-MS. Some samples were also collected directly on a LpDNPH-cartridge, followed by HPLC-MS analysis. When experiments were carried out at 50 Torr both GC-MS and HPLC-MS measurements showed that campholenealdehyde and pinonaldehyde were identified as condensable oxidation products for the alpha-pinene/OH reaction, with pinonaldehyde being the main product. Furthermore, the LN2 trap collection method based on the in situ conversion of aldehydes and ketones to their 2,4-dinitrophenylhydrazone derivatives allowed the determination of formaldehyde, acetaldehyde and acetone. Although formaldehyde and acetone are present in small amounts in blank samples it could be established that formaldehyde and acetone are also formed in the alpha-pinene/OH reaction.     

HPLC–MS determination of the oxidation products of the reaction between α- and β-pinene and OH radicals

Biogenic non-methane hydrocarbons such as isoprene, alpha-pinene, and beta-pinene, are emitted by forests in very large quantities. To evaluate the role of alpha- and beta-pinene and their contribution to the global production of trace gases and especially aerosol precursors, a study of the oxidation mechanism of alpha- and beta-pinene with hydroxyl radicals must be conducted.The degradation products of both monoterpenes with hydroxyl radicals were identified and quantified in a fast-flow reactor. The products were collected on a liquid-nitrogen trap coated with a 2,4-DNPH solution to which two internal standards (benzaldehyde-2,4-DNPH and tolualdehyde-2,4-DNPH) had been added. The collection method was based on the in situ conversion of aldehyde and/or ketone compounds to their 2,4-dinitrophenylhydrazone derivatives. The derivatives were analyzed by HPLC-MS using APCI(-). TIC chromatograms and mass spectral data for the various oxidation products are presented.For alpha-pinene, pinonaldehyde is the most important degradation product, with smaller amounts of acetone, formaldehyde, campholenealdehyde, and acetaldehyde. For beta-pinene, nopinone and formaldehyde are the most abundant products, of almost equal importance, whereas acetone and acetaldehyde are minor compounds.     

An optimized method for the determination of volatile and semi-volatile aldehydes and ketones in ambient particulate matter

A method has been developed to measure aldehydes and ketones associated with atmospheric particles. Carbonyl compounds from particulate material collected on Teflon-coated glass-fiber filters were simultaneously extracted and derivatized with an appropriate 2,4-dinitrophenylhydrazine (2,4-DNPH) solution. The efficiency of this procedure utilizing various 2,4-DNPH concentrations and solvent compositions was studied for 13 carbonyl compounds of atmospheric importance. These include formaldehyde, acetaldehyde, acetone, dicarbonyls such as glyoxal and methylglyoxal, and biogenic carbonyls such as pinonaldehyde and nopinone. An extraction solution containing 3 × 10^?2 M 2,4-DNPH, in 60% acetonitrile/40% water, and pH 3 was most efficient in extracting and derivatizing these aldehydes and ketones (83-100% recovery). Improved sample enrichment and 2,4-DNPH purification methods were developed that afforded detection limits of 0.009-5.6 ng m^?3. The relative standard deviation for replicate analyses were 1.9-10.1%. Carbonyl compounds in ambient particulate samples were quantified during a recent field study. Median values for nine carbonyl species ranged from 0.01-33.9 ng m^?3 during the study.     

Atmospheric chemistry of 3-pentanol: kinetics, mechanisms, and products of Cl atom and OH radical initiated oxidation in the presence and absence of NOX

Smog chamber/FTIR techniques were used to study the atmospheric chemistry of 3-pentanol and determine rate constants of k(Cl+3-pentanol) = (2.03 +/- 0.23) x 10 (-10) and k(OH+3-pentanol) = (1.32 +/- 0.15) x 10 (-11) cm (3) molecule (-1) s (-1) in 700 Torr of N 2/O 2 diluent at 296 +/- 2 K. The primary products of the Cl atom initiated oxidation of 3-pentanol in the absence of NO were (with molar yields) 3-pentanone (26 +/- 2%), propionaldehyde (12 +/- 2%), acetaldehyde (13 +/- 2%) and formaldehyde (2 +/- 1%). The primary products of the Cl atom initiated oxidation of 3-pentanol in the presence of NO were (with molar yields) 3-pentanone (51 +/- 4%), propionaldehyde (39 +/- 2%), acetaldehyde (44 +/- 4%) and formaldehyde (4 +/- 1%). The primary products of the OH radical initiated oxidation of 3-pentanol in the presence of NO were (with molar yields) 3-pentanone (58 +/- 3%), propionaldehyde (28 +/- 2%), and acetaldehyde (37 +/- 2%). In all cases the product yields were independent of oxygen concentration over the partial pressure range 10-700 Torr. The reactions of Cl atoms and OH radicals with 3-pentanol proceed 26 +/- 2 and 58 +/- 3%, respectively, via attack on the 3-position to give an alpha-hydroxyalkyl radical, which reacts with O 2 to give 3-pentanone. The results are discussed with respect to the literature data and atmospheric chemistry of 3-pentanol.     

Application of a data-processing model to determine the optimal sampling conditions for liquid phase trapping of atmospheric carbonyl compounds

The reactivity of two fluorescent derivatization reagents, 2-diphenyl-1,3-indandione-1-hydrazone (DIH) and 2-aminooxy-N-[3-(5-dimethylamino-naphtalene-1-sulfonamino)-propyl]-acetamide (dansylacetamidooxyamine, DNSAOA), was studied towards selected atmospheric carbonyl compounds. The results were compared to those obtained using the 2,4-dinitrophenylhydrazine (2,4-DNPH) UV–vis reagent, a standard well-established technique used to detect atmospheric carbonyl compounds. The experimental rate constant were integrated into a data-processing model developed in the laboratory to simulate the trapping efficiencies of a mist chamber device as a function of temperature, reagent and solvent type among others. The results showed that in an aqueous solution, DNSAOA exhibits a higher reactivity towards carbonyl compounds without the addition of an acidic catalyst than 2,4-DNPH. It was observed that DNSAOA can trap efficiently water-soluble gaseous compounds (for example formaldehyde). However, because of a high initial contamination of the reagent caused by the synthesis procedure used in this work, DNSAOA cannot be used in high concentrations. As a result, very low trapping efficiencies of less reactive water-insoluble gaseous compounds (acetone) using DNSAOA are observed. However, the use of an organic solvent such as acetonitrile improved the trapping efficiencies of the carbonyl compounds. In this case, using DIH as the derivatization reagent (DNSAOA is not soluble in acetonitrile), trapping efficiencies greater than 95% were obtained, similar to 2,4-DNPH. Moreover, fluorescence associated with DIH derivatives (detection limits 3.33 × 10⁻⁸ M and 1.72 × 10⁻⁸ M for formaldehyde and acetone, respectively) is further advantage of this method for the determination of carbonyl compounds in complex matrix compared to the classical UV–vis detection method (detection limits 3.20 × 10⁻⁸ M and 2.9 × 10⁻⁸ M for formaldehyde and acetone, respectively).     

Study of the carbonyl products of terpene/OH radical reactions: detection of the 2,4-DNPH derivatives by HPLC-MS

The oxidation of the terpenes - and -pinene, limonene and ³-carene by hydroxyl radicals has been investigated in a fast-flow reactor coupled to a liquid nitrogen trap for collecting the carbonyl compounds. Identification of the products was performed via 2,4-dinitrophenylhydrazone (DNPH) derivatization of the carbonyls to form the mono- and di-DNPH derivatives, which were analysed by high-performance liquid chromatographic (HPLC)-DAD (diode array detector) and HPLC-mass spectrometry (HPLC-MS). Both electrospray ionization [ESI(–)] and atmospheric pressure chemical ionization [APCI(–)] were suitable for the detection of the DNPH derivatives of formaldehyde, acetaldehyde, myrtanal, campholene aldehyde, perillaldehyde, acetone, nopinone, trans-4-hydroxynopinone and 4-acetyl-1-methylcyclohexene. Also the mono-DNPH derivatives of the dicarbonyl compounds pinonaldehyde, endolim and caronaldehyde could be identified. The MS² spectra generated in the ion trap of the mass spectrometer allowed us to distinguish between aldehydes and ketones on the basis of the characteristic fragment ion m/z 163 for the aldehydes. For the quantitative analysis of the mono-DNPH derivatives, ESI(–) in combination with single ion monitoring (SIM) detection showed the lowest detection limits. For the quantification of the dicarbonyl compounds, the acid-sensitive di-DNPH derivatives had to be formed by keeping the acidity in the acid-catalysed derivatization reaction at about 1.7 mM H₂SO₄. Detection of these dicarbonyl compounds can only be performed by APCI(–) with somewhat lesser sensitivity than by HPLC-DAD.     

Reactions of the alkoxy radicals formed following OH-addition to alpha-pinene and beta-pinene. C-C bond scission reactions.

The atmospheric degradation pathways of the atmospherically important terpenes alpha-pinene and beta-pinene are studied using density functional theory. We employ the correlation functional of Lee, Yang, and Parr and the three-parameter HF exchange functional of Becke (B3LYP) together with the 6-31G(d) basis set. The C-C bond scission reactions of the beta-hydroxyalkoxy radicals that are formed after OH addition to alpha-pinene and beta-pinene are investigated. Both of the alkoxy radicals formed from the alpha-pinene-OH adduct possess a single favored C-C scission pathway with an extremely low barrier (approximately 3 kcal/mol) leading to the formation of pinonaldehyde. Neither of these pathways produces formaldehyde, and preliminary computational results offer some support for suggestions that 1,5 or 1,6 H-shift (isomerization) reactions of alkoxy radicals contribute to formaldehyde production. In the case of the alkoxy radical formed following OH addition to the methylene group of beta-pinene, there exists two C-C scission reactions with nearly identical barrier heights (approximately 7.5 kcal/mol); one leads to known products (nopinone and formaldehyde) but the ultimate products of the competing reaction are unknown. The single C-C scission pathway of the other alkoxy radical from beta-pinene possesses a very low (approximately 4 kcal/mol) barrier. The kinetically favored C-C scission reactions of all four alkoxy radicals appear to be far faster than expected rates of reaction with O2. The rearrangement of the alpha-pinene-OH adduct, a key step in the proposed mechanism of formation of acetone from alpha-pinene, is determined to possess a barrier of 11.6 kcal/mol. This value is consistent with another computational result and is broadly consistent with the modest acetone yields observed in product yield studies.     

Evaluation of Monolithic Columns for Determination of Formaldehyde and Acetaldehyde in Sugar Cane Spirits by High-Performance Liquid Chromatography

Abstract

High-Performance Liquid Chromatography (HPLC) conditions are described for separation of 2,4-dinitrophenylhydrazone (2,4-DNPH) derivatives of carbonyl compounds in a 10 cm long C₁₈ reversed phase monolithic column. Using a linear gradient from 40 to 77% acetonitrile (acetonitrile-water system), the separation was achieved in about 10 min—a time significantly shorter than that obtained with a packed particles column. The method was applied for determination of formaldehyde and acetaldehyde in Brazilian sugar cane spirits. The linear dynamic range was between 30 and 600 µg L^?1, and the detection limits were 8 and 4 µg L^?1 for formaldehyde and acetaldehyde, respectively.     

Direct measurement of Criegee intermediate (CH2OO) reactions with acetone, acetaldehyde, and hexafluoroacetone

Criegee biradicals, i.e., carbonyl oxides, are critical intermediates in ozonolysis and have been implicated in autoignition chemistry and other hydrocarbon oxidation systems, but until recently the direct measurement of their gas-phase kinetics has not been feasible. Indirect determinations of Criegee intermediate kinetics often rely on the introduction of a scavenger molecule into an ozonolysis system and analysis of the effects of the scavenger on yields of products associated with Criegee intermediate reactions. Carbonyl species, in particular hexafluoroacetone (CF(3)COCF(3)), have often been used as scavengers. In this work, the reactions of the simplest Criegee intermediate, CH(2)OO (formaldehyde oxide), with three carbonyl species have been measured by laser photolysis/tunable synchrotron photoionization mass spectrometry. Diiodomethane photolysis produces CH(2)I radicals, which react with O(2) to yield CH(2)OO + I. The formaldehyde oxide is reacted with a large excess of a carbonyl reactant and both the disappearance of CH(2)OO and the formation of reaction products are monitored. The rate coefficient for CH(2)OO + hexafluoroacetone is k(1) = (3.0 ± 0.3) × 10(-11) cm(3) molecule(-1) s(-1), supporting the use of hexafluoroacetone as a Criegee-intermediate scavenger. The reactions with acetaldehyde, k(2) = (9.5 ± 0.7) × 10(-13) cm(3) molecule(-1) s(-1), and with acetone, k(3) = (2.3 ± 0.3) × 10(-13) cm(3) molecule(-1) s(-1), are substantially slower. Secondary ozonides and products of ozonide isomerization are observed from the reactions of CH(2)OO with acetone and hexafluoroacetone. Their photoionization spectra are interpreted with the aid of quantum-chemical and Franck-Condon-factor calculations. No secondary ozonide was observable in the reaction of CH(2)OO with acetaldehyde, but acetic acid was identified as a product under the conditions used (4 Torr and 293 K).     

高效液相色谱法测定卷烟粘合剂中甲醛、乙醛的含量

提出了预衍生化高效液相色谱法测定卷烟粘合剂中甲醛、乙醛含量的方法。卷烟粘合剂中醛经纯净水提取,离心机离心后分取部分上层清液,与2,4-二硝基苯肼衍生反应,生成的甲醛和乙醛的2,4-二硝基苯腙,用C18柱进行分离,用乙腈与水的混合物作流动相。在358nm紫外波长下检测,用醛衍生物配制标准定量。甲醛和乙醛在0.10～10.0mg·mL-1范围内呈线性。甲醛加标回收率在98.3%～118.9%之间,乙醛加标回收率在79.2%～89.2%之间,相对标准偏差(n=5)均小于5%。     

Highly sensitive and selective catalytic determination of formaldehyde and acetaldehyde

A highly sensitive, simple and selective kinetic method was developed for the determination of ultra-trace levels of formaldehyde and acetaldehyde based on their catalytic effect on the oxidation of N,N-diethyl-p-phenylenediamine (DPD) with hydrogen peroxide. The reaction was monitored spectrophotometrically by tracing the formation of the red-colored oxidized product of DPD at 510nm, within 30s of mixing the reagents. The optimum reaction conditions were: 20mmolL(-1) DPD, 250mmolL(-1) H(2)O(2), 150mmolL(-1) phosphate, 150mmolL(-1) citrate and pH 6.60+/-0.05 at 25 degrees C. Following the recommended procedure, formaldehyde and acetaldehyde could be determined with linear calibration graphs up to 0.50 and 1.4microg mL(-1) and detection limits, based on the 3S(b)-criterion, of 0.015 and 0.035microg mL(-1), respectively. In addition, analytical data for other 10 aldehydes were also presented. The high sensitivity and selectivity of the proposed method allowed its successful application to rain water, mainstream smoke (MSS) and disposed tips of smoked cigarettes (DTSC). A sample aliquot was directly analyzed for its total water-soluble aldehyde content. A second sample aliquot was heated at 80 degrees C for 10min to expel acetaldehyde and the aliquot was analyzed for its content of other water-soluble aldehydes (expressed as formaldehyde equivalent), and acetaldehyde was determined by difference. The analytical results were in excellent agreements with those obtained following the standard HPLC method based on pre-column derivatization with 2,4-dinitrophenylhydrazine. Moreover, published catalytic-spectrophotometric methods for the determination of aldehydes were reviewed.     

Mechanism and kinetics of the selective catalytic oxidation of acetone

The kinetics of the heterogeneous catalytic vapor-phase oxidation of acetone on vanadium pentoxide was studied under gradientless conditions at the temperature 413–453 K. The degree of conversion of acetone did not exceed 20%. The main carbon-containing oxidation products were acetic acid and carbon dioxide. Methanol and small quantities of formaldehyde and acetaldehyde were also formed. Possible mechanisms of the reaction are discussed.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 22, No. 2, pp. 252–254, March–April, 1986.     

Determination of higher molecular weight aliphatic aldehydes and ketones

The visible absorption spectra have been measured for the reaction products formed by aldehydes and ketones with p-nitrobenzenediazonium fluoborate in a phosphoric acid-2-methoxyethanol solvent medium. The absorption maxima for the reaction products of higher molecular weight aldehydes and ketones are much more intense than those formed by formaldehyde, acetaldehyde and acetone. This intensity effect has been used to analyze for propionaldehyde in mixtures also containing formaldehyde, acetaldehyde or acetone. The nature of the reaction products are considered.     

Determination of aldehydes in fish by high-performance liquid chromatography

A new analytical method to determine trace volatile aldehydes isolated from the headspace of fish meat at room temperature by high-performance liquid chromatography (HPLC) in the form of 2,4-dinitrophenylhydrazone (DNPHo) derivatives has been developed. Aliquots (50 g) of the fish purée were introduced into a 500-mL glass recipient and were purged with N2 for 40 min through two SEP-PAK C18 cartridges (connected in series) coated with an acid solution of 2,4-dinitrophenylhydrazine. The cartridges were then eluted with acetonitrile (2 mL) and the 2,4-DNPHo formed was quantitated by HPLC-UV analysis using a Zorbax C18 column. The isolated compounds from the dynamic headspace sampling of four kinds of fish species were saturated aldehydes, formaldehyde, acetaldehyde, propanal, butanal, pentanal, and hexanal. Under optimized conditions the detection limits of the HPLC method were in the range of 0.75 nmol/g (formaldehyde) to 2.19 nmol/g (hexanal). The calibration curves were linear in the concentration range from 1.3 nmol/mL to 12.5 nmol/mL. Propanal and acetaldehyde were the major carbonyl compounds identified (ranging from 3.9 nmol/g and 10 nmol/g). This study has revealed the widespread occurrence of formaldehyde, acetaldehyde, propanal, butanal, pentanal, and hexanal in fish meat.     

高效液相色谱法测定卷烟醋酸纤维滤棒中甲醛、乙醛和丙酮的含量

建立了高效液相色谱法同时测定卷烟醋酸纤维滤棒中甲醛、乙醛和丙酮含量的方法,采用Acclaim(R)Explosive E2 C18色谱柱,流动相为乙腈/水梯度洗脱,流速为0.5 mL/min,检测波长为352 nm,对甲醛、乙醛和丙酮的分析取得满意的效果.甲醛、乙醛、丙酮的回收率分别为95.3％～105.6％、86.1...     

Poly(allylamine) beads as selective sorbent for preconcentration of formaldehyde and acetaldehyde in high-performance liquid chromatographic analysis

Formaldehyde and acetaldehyde in water were determined by preconcentration with poly(allylamine) beads, derivatization with 2,4-dinitrophenylhydrazine (DPH) and analysis by HPLC. Poly(allylamine) beads (0.5 g) were used to adsorb formaldehyde and acetaldehyde at 1.2-150 microg l(-1) and 3.5-220 microg l(-1) from water (1 l). The concentration factor is 50 fold. The aldehydes were eluted and derivatized with 2 mM DPH in 0.5 M H2SO4 (10 ml). The time of analysis was 1 h. The detection limits (S/N=3) for formaldehyde and acetaldehyde were 0.6 and 2 microg l(-1), respectively.     

Real-time quantitative analysis of volatile products generated during solid-state polypropylene thermal oxidation

Analysis of volatile organic compounds (VOCs) during PP thermal oxidation under three oxygen partial pressures (0%, 21% and 100% of atmospheric pressure) at 140 °C was performed by proton transfer reaction coupled with Fourier transform ion cyclotron resonance mass spectrometry. Six main VOCs were identified: acetone, acetic acid, 2,4-pentanedione, acetaldehyde, formaldehyde and methyl acrolein. Their formation was shown to obey two main reaction pathways, both involving methyne units as driving oxidation sites: (i) the widely accepted chain scission mechanism of tertiary alkoxy radicals, which generates primary radicals undergoing secondary reactions leading to the oxidation of methylene units; (ii) the chain scission mechanism occurring on tertiary alkyl radical, which is proposed here as a realistic path leading to methyl acrolein. The relative proportions of the six main VOCs depend on the oxygen partial pressure, which mostly impacts the oxidation of methylene units rather than the competition between the two previous paths.     

Spectrophotometric determination of flucythrinate (synthetic pyrethroid) using phenylhydrazines

Three spectrophotometric methods are described for determining flucythrinate, based on formation of coloured compounds when one of the hydrolysed products of flucythrinate is condensed with 2,4-dinitrophenylhydrazine (2,4-DNPH), 4-nitrophenylhydrazine (4-NPH) or 2,4,6-trinitrophenylhydrazine (2,4,6-TNPH) in the presence of methanolic potassium hydroxide. These coloured compounds absorb strongly at 465 nm (2,4-DNPH), 540 nm (4-NPH) and 485 nm (2,4,6-TNPH). The methods are applicable over the range 0.1-8.0 mug/ml for 2,4-DNPH, 0.5-6.5 mug/ml for 4-NPH and 0.1-6 mug/ml for 2,4,6-TNPH. The methods are rapid, sensitive and selective and can be used for microdetermination of flucythrinate in a commercial formulation, water, grains and crop samples.     

Experimental and theoretical study of the reaction of OH radical with sabinene

The gas phase sabinene + OH reaction is studied both experimentally and theoretically. Product yields from the reaction of sabinene with OH radicals have been measured in the absence of NOx in the UCC chamber (Cork, Ireland) and in the presence of NOx in the LISA chamber. Three primary carbonyl compounds were observed and quantified: acetone in [(24 +/- 6)%], formaldehyde in [(25 +/- 6)%] and sabinaketone in [(20 +/- 6)%]. The simultaneous quantification of these compounds is one of the major results of this work. The mechanism of product formation for this reaction has been studied using the quantum chemical DFT-B3LYP (6-31G(d,p) method. According to these calculations, the H-atom abstraction channel from sabinene by OH in the initial oxidation step may be taken into account to explain the acetone production. Sabinaketone and formaldehyde are mainly products of the addition channels of OH on the -C=CH2 double bond of sabinene. This is the first theoretical work on the title reaction.