Role of processing in improving the critical current of Ag/BPSCCO tapes

Silver-clad tapes of highT _c Bi-Pb-Sr-Ca-Cu-O superconductors have been fabricated through the powder-in-tube method. The critical current density, J _c , of a thick tape was 534 A.cm⁻² (77 K, 0 T). Subsequent rolling and sintering of the tapes led to a gradual decrease inJ _c, instead of the expected increase. This was caused by the microcracks developed in the core material by a rather drastic reduction during the rolling of the tapes. A modified and well controlled rolling technique, on the other hand, resulted in much improvedJ _c values. Repeated rolling and sintering resulted in a good grain alignment and no microcracks were observed. In the present studies, maximumJ _c of 1846 A.cm⁻² (77 K, 0 T) and 2.43 × 10⁴ A.cm⁻² (4.2 K, 0 T) have been obtained Optimization of the processing and sintering parameters are expected to lead to still higherJ _c values.     

Further studies on Ag/BPSCCO tapes using low purity materials

Transmission electron microscopic (TEM) studies are reported on Ag-clad Bi_1.7 Pb_0.4Sr_1.8Ca₂Cu_3.5O _x tapes prepared by using low purity (98–99%) commercial grade materials. The self-fieldJ _c values of these tapes viz. 6.14 × 10³ A.cm⁻² at 77 K and 1.4 × 10⁵ A.cm⁻² at 4.2 K, reported in an earlier publication, were significantly higher than the correspondingJ _c values in tapes prepared with high purity (99.99%) materials. The TEM pictures on the low purity core material of the tapes reveal the presence of stacking faults and the intergrowth of the 2212 and 2223 phases which could be acting as flux pinning sites and responsible for enhancedJ _c values. These defects can perhaps be traced back to the presence of 60 ppm iron in the low purity CuO as revealed by atomic absorption analysis reported earlier.     

Transport properties of long monofilamentary Bi(2223) tapes

Summary Monofilamentary Bi(2223) tapes withJ _c(77 K, 0 tesla) up to 30 000 A/cm² have been prepared by cold rolling using the powder-in-tube method. An optimization of the precursor powders has led to a higher phase purity after the reaction heat treatment. The deformation process has been optimized in order to increase the oxide density and to reduce sausaging effects on the oxide thickness. The transport properties of these tapes have been studied in a wide range of temperature (4.2K-T _c) and magnetic fields (up to 28 tesla). The critical-current values at 77 K fields of 0.5 T and 1 T parallel to the tape surface are 10 000 A/cm² and 5400 A/cm², respectively. At 4.2 K theJ _c value decreases from 1.6·10⁵ A/cm² at 0 T to 6·10⁴ A/cm² at 15 T. At fields higher than 15 tesla a very low field dependence ofJ _c has been found, regardless of the tape orientation. Transport properties have also been studied by cutting small sections of the tape in order to investigate the local critical-current distribution. It has been found that, even in rolled tapes of good quality (J _c (77 K, 0 T)>20000 A/cm²), theJ _c distribution is homogeneous: the critical current density increases gradually from the centre of the tape to the sides, the latter exhibiting much higherJ _c (46000 A/cm²) than in the centre (18000 A/cm²). Paper presented at the ?VII Congresso SATT?, Torino, 4–7 October 1994.     

Critical current densities of high pressure oxygen sputtered thin films of YBa2Cu3O7−x by non-resonant rf absorption method

The critical current densities (J _c) have been measured at 77K in high pressure oxygen sputtered thin films of YBa₂Cu₃O_7−x superconductor using the non-resonant rf absorption technique. High values ofJ _c (∼ 10⁵ A/cm²) are observed in these relatively large area (∼ 1·2 cm²) films.     

Electrical and magnetic properties of hot extruded Bi-2223/Ag concentric tapes

Summary In this work we report on the anisotropic physical properties of silver-sheathed Bi-2223 tapes fabricated by means of hot extrusion and repeated pressing and sintering processes. The obtained Bi-2223/Ag short tapes, having critical current densitiesJ _c of 20–30 kA/cm² at 77 K, 0 T, were measured in external magnetic fields up to 0.5T applied in two different orientations (i.e. μ₀H‖(a,b)-planes and μ₀H ⊥(a,b)-planes). The magnetic characterizations were performed in a wide range of temperatures and magnetic fields to study the first magnetization curve of tapes evaluating the lower critical fields μ₀H_c1⊥ab and ⊥₀H_c1#x2016;ab and their dependences on temperature. TheJ _c values at different fields in the temperature range 4.6–90 K, calculated from the magnetization data by the critical state model, are also presented. Paper presented at the ?VII Congresso SATT?, Torino, 4–7 October 1994.     

Critical current in silver clad Y-Ba-Cu-O superconducting wires

Silver clad wires of highT _c superconductor Y₁Ba₂Cu₃O_7−x have been fabricated through the powder metallurgy technique. The reacted wires show a midpointT _c of 84K. A critical current density of 26·4 A cm⁻² (77K, 0T) is obtained in these wires. The wires, however, turn complete normal only at a current density of 280 A cm⁻². The reasons for low critical current density obtained in these wires are discussed.     

Spin-spin interaction of Ni2+ ions in ZnSiF6·6H2O

The angular dependences of the electron spin resonance spectrum of 1% Ni²⁺ ions in a ZnSiF₆·6H₂O matrix are investigated experimentally at 36 GHz and 4.2 K. Besides the main spectrum of the isolated ion, we observed a spectrum due to interacting pairs of Ni²⁺ ions, located in the first (nn) and second (2n) coordination spheres and coupled by, besides the magnetic dipole-dipole interaction, isotropic exchange: J _nn = (−197±1)×10⁻⁴, J _2nα = (−5±1)×10⁻⁴, and J _2nβ = (3±2)×10⁻⁴ cm⁻¹. Lines due to other isolated Ni²⁺ ions, which have a different initial splitting D, are also present in the spectrum with intensity comparable to the pair spectrum. Low-symmetry distortions of the crystal field are observed, caused by a pair of impurity ions located close to one another. It is shown that the previously proposed interpretation is incorrect. Fiz. Tverd. Tela (St. Petersburg) 41, 1602–1608 (September 1999)     

Weak exchange interactions in the heteronuclear crystal CuPr2(CCl3COO)8·6H2O

The new heteronuclear crystal CuPr₂(CCl₃COO)₈·6H₂O, constructed of chains containing copper and praseodymium atoms, has been synthesized and investigated by EPR at 9.3 GHz at temperatures ranging from room temperature down to 10 K. At temperatures T∼300–130 K, EPR spectra are observed which are characteristic of isolated polyhedra of copper ions with g _z=2.330±0.005, g _x,y =2.053±0.005, A _z=139×10⁻⁴ cm⁻¹, and A _x,y <26×10⁻⁴ cm⁻¹. At temperatures T<130 K a complex spectrum is observed, associated with the appearance of weak exchange interactions between the copper ions in the chain (J _Cu-CuΣS _i·S _i+1), comparable in magnitude with the hyperfine interactions J _Cu-Cu=0.015 cm⁻¹ at T=10 K. The magnitude of the exchange interaction decreases smoothly as the temperature is raised. It is conjectured that orbitals of the praseodymium ions participate in the process of indirect exchange between the copper ions. Fiz. Tverd. Tela (St. Petersburg) 41, 2154–2157 (December 1999)     

The transition width and critical current density measurements on slow-cooled YBa2Cu3O7−x superconductor

It is shown that by adopting a very gradual programmed cooling procedure in oxygen environment one can obtain a sharp transition (ΔT _c⋍1 K) in YBa₂Cu₃O_7−x while retaining the high-T _c value (⋍105 K) of samples prepared by a semi-wet route. This is attributed to a maximum occupancy of oxygen at 0 1/2 0 sites and a near-perfect ordering of vacancies at 1/2 0 0 sites in the orthorhombic unit cell which maximizes the availability of conduction paths in the form of continuous CuO₄ chains. Critical current densities (J _c) of 204 A cm⁻² are obtained for bulk samples at 77 K. It is suggested that the intergrain coupling is weak and thus limits the transportJ _c-values.     

Electrical and magnetic characterization of hot-extruded BSCCO tape samples

Summary Ag/BSCCO-2223 phase tapes were prepared with a new plastic deformation cycle. Starting from the hot extrusion of composite billets, hundreds of metres of tape 0.15×3 mm were obtained by drawing and rolling the extruded bars. The cross-section, monofilamentary with a central Ag insert, is quite regular along all the length. Samples from 30 cm to 100 cm in length were heat-treated at different temperatures between 830°C and 480°C in Ar+10% O₂ atmosphere. Electrical-transport properties were tested at 77K.J _c of 3000 A/cm² were usually achieved after first heat treatment. The superconducting properties were also tested by magnetic measurements using a vibrating sample magnetometer. Paper presented at the ?VII Congresso SATT?, Torino, 4–7 October 1994.     

Atmospheric gamma rays in the energy region 40–1000 GeV

A large stack of lead-emulsion sandwich detector assembly was flown over Hyderabad, India. High energy gamma rays at the float altitude were unambiguously identified from the cascades they induced, and their energies reliably determined by improved methods. From an analysis of 163 gamma rays of energy ≳ 30 GeV, it is found that the differential energy spectrum is represented by the power lawJ _r (E)= 129·4E ^{−2·62±0·12} photons m⁻² sr⁻¹sec⁻¹ GeV⁻¹ at an effective atmospheric depth of 14·3 g cm⁻²; this is the first reliable balloon measurement of atmospheric gamma rays in the energy range 40–1000 GeV. After correcting for the gamma rays radiated by the primary cosmic ray electrons, the production spectrum of gamma rays, resulting from the collisions of cosmic ray nuclei with air nuclei, at the top of the atmosphere isP _r (E, 0)=8·2 × 10⁻⁴ E^2.60±0.09 photons g⁻¹sr⁻¹sec⁻¹ GeV⁻¹. The atmospheric propagation of the electromagnetic component due to the cascade process is also derived from the gamma ray production spectrum.     

Properties of Nb3Ge tapes for high field magnets

A laboratory process for long Nb₃Ge tapes fabrication by chemical vapor deposition (CVD) has been set up. The Nb₃Ge tapes which were fabricated offer the possibility of high current and high field operation at 4.2 K since the values of critical current densities, J_c, measured in high magnetic fields at 20T and 4.2K exceed 5 × 10⁴ A cm^?2 which is the generally accepted criterion for producing a superconducting magnet.     

ESR of V4+ in α-RbTiOPO4 single crystals

We have recorded and investigated the ESR spectrum of vanadium-doped α-RbTiOPO₄ single crystals in the temperature interval 77–300 K. Two types of structurally distinct centers, V1 and V2, with a 4:1 ratio of the peak intensities were observed. The angular dependences of the resonance magnetic fields are described by a spin Hamiltonian corresponding to axial symmetry with the parameters g _∥1=1.9305, g _⊥1=1.9565, A _∥1=−168.2×10⁻⁴cm⁻¹, and A _⊥1=−54.3×10⁻⁴cm⁻¹ for V1 centers and g _∥2=1.9340, g _⊥2=1.9523, A _∥2=−169.0×10⁻⁴cm⁻¹, and A _⊥2=−55.2×10⁻⁴cm⁻¹ for V2 centers. A model of a paramagnetic center is proposed: The vanadium ions replace titanium ions in two structurally distinct positions Ti1 and Ti2 (V1 and V2 centers, respectively). The possibility that a VO²⁺ ion forms when α-RbTiOPO₄ crystals and crystals of the KTP group (KTiOPO₄, NaTiOPO₄, α-and β-LiTiOPO₄), studied earlier, are doped with vanadium is discussed. Fiz. Tverd. Tela (St. Petersburg) 40, 534–536 (March 1998)     

Effect of mechanical deformation on the critical current in YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7−<Emphasis Type="Italic">b</Emphasis></Subscript> superconducting films

It is shown that local mechanical bending of YBa₂Cu₃O_7−b Ag-coated superconducting films deposited on flexible metal substrates in the temperature interval 77–300 K may increase the critical density J _c of the transport current to values as high as 10⁶ A/cm² or even higher at 77 K. Also, bending decreases the voltage criterion. This means a rise in the intergranular conductivity and, accordingly, a reduction of Joule losses.     

MgB2 coated superconducting tapes with high critical current densities fabricated by hybrid physical-chemical vapor deposition

The MgB₂ coated superconducting tapes have been fabricated on textured Cu (0 0 1) and polycrystalline Hastelloy tapes using coated conductor technique, which has been developed for the second generation high temperature superconducting wires. The MgB₂/Cu tapes were fabricated over a wide temperature range of 460-520 °C by using hybrid physical-chemical vapor deposition (HPCVD) technique. The tapes exhibited the critical temperatures (T_c) ranging between 36 and 38 K with superconducting transition width (ΔT_c) of about 0.3-0.6 K. The highest critical current density (J_c) of 1.34 × 10⁵ A/cm² at 5 K under 3 T is obtained for the MgB₂/Cu tape grown at 460 °C. To further improve the flux pinning property of MgB₂ tapes, SiC is coated as an impurity layer on the Cu tape. In contrast to pure MgB₂/Cu tapes, the MgB₂ on SiC-coated Cu tapes exhibited opposite trend in the dependence of J_c with growth temperature. The improved flux pinning by the additional defects created by SiC-impurity layer along with the MgB₂ grain boundaries lead to strong improvement in J_c for the MgB₂/SiC/Cu tapes. The MgB₂/Hastelloy superconducting tapes fabricated at a temperature of 520 °C showed the critical temperatures ranging between 38.5 and 39.6 K. We obtained much higher J_c values over the wide field range for MgB₂/Hastelloy tapes than the previously reported data on other metallic substrates, such as Cu, SS, and Nb. The J_c values of J_c(20 K, 0 T) ∼5.8 × 10⁶ A/cm² and J_c(20 K, 1.5 T) ∼2.4 × 10⁵ A/cm² is obtained for the 2-μm-thick MgB₂/Hastelloy tape. This paper will review the merits of coated conductor approach along with the HPCVD technique to fabricate MgB₂ conductors with high T_c and J_c values which are useful for large scale applications.     

Polarisation resistance of the O2, Au/O2− and H2-H2O, Au/O2− electrode systems

Gold electrodes with known contact geometries were studied using impedance spectroscopy. From these data it was possible to determine the specific polarisation conductivity per unit length of three-phase boundary (TPB). The values were found to be (3÷22)×10⁻⁴ S·cm⁻¹ dependent on the electrode history in pure oxygen at 977 °C and 2×10⁻⁶ S·cm⁻¹ at 977 °C in “pure” hydrogen (P_O2=10⁻²⁰ atm at 1001 °C). The results are compared with previous data obtained for platinum electrodes.     

Trap-centers of self-interstitials in silicon

Deep-level profiles were measured radially acrossn-type FZ silicon wafers containing A-swirl defects by applying DLTS to an array of Schottky contacts. The trapparameters were obtained very accurately using a computer-fit procedure for the full DLTS peaks. Two acceptor levels atE _c −0.49 eV (σ _n =6.6×10⁻¹⁶cm²) andE _c −0.07 eV (σ _n =4.6×10⁻¹⁶cm²) were observed, which varied oppositely to the A-swirl defect density. At short ranges (1–2mm) the trap concentration-profile was smeared out and did not follow the strong fluctuations in the etch pattern. Both levels were measured together with the same concentration. The profiles indicate outdiffusion. A level atE _c −0.14 eV (σ _n =1.1×10⁻¹⁶cm²) was not related to A-swirl defects. A level atE _c −0.11 eV (σ _n =1.1×10⁻¹⁵cm²) was only detected in one ingot. The properties of the deep level atE _c −0.49 eV are discussed in the light of published DLTS results reported for γ-irradiation, laser annealing after self-implantation, annealing under pressure and oxidation of silicon samples. It is concluded, that this level is related to interstitial silicon rather than to an impurity.     

X-ray determination of thermal expansion of cadmium fluoride and lead fluoride

The lattice parameters of CdF₂ andβ-PbF₂ have been determined over the temperature range 300–670 K. The coefficient of expansion at room temperature is 21·3 × 10⁻⁶ K⁻¹ and 25·4 × 10⁻⁶ K⁻¹ for CdF₂ and PbF₂ respectively and it increases linearly with temperature over the range of temperature covered. The Grüneisen parameter decreases with temperature in both the crystals.     

Spin susceptibility of neutron-irradiation-disordered YBa2Cu3O6.9 in the normal and superconducting states

The spin-spin relaxation rate ⁶³ T ₂ ⁻¹ of ⁶³Cu nuclei in CuO₂ layers is measured in the normal and superconducting states of the compound YBa₂Cu₃O_6.9 (T _c ^onset =94 K) subjected to radiation-induced disordering by a fast-neutron flux Φ to T _c ^onset =68 K (Φ=7×10¹⁸ cm⁻²) and T _c ^onset <4 K (Φ=12×10¹⁸ cm⁻²). It is found that as the structural disorder increases, the contribution of the indirect spin-spin interaction ⁶³ T _2G ⁻¹ , which is related to the value of the spin susceptibility at the boundary of the Brillouin zone of the copper planes χ_s(q={π/a; π/a}), decreases slightly at the transition to the superconducting state for the initial sample and remains unchanged for the weakly disordered sample. This behavior of the short-wavelength contribution to the spin susceptibility attests to the stability of the x ²−y ² symmetry of the energy gap against structural disorder, in accordance with proposed theoretical models of Cooper pairing for high-T _c cuprates. Pis’ma Zh. éksp. Teor. Fiz. 67, No. 3, 172–177 (10 February 1998)