基于反射式脉冲红外热成像法的定量测量方法研究

本文提出了一种利用反射式脉冲热成像法测量缺陷深度、热扩散系数或缺陷界面热波反射系数的方法. 首先,介绍了脉冲热成像法的基本原理以及定量测量算法.其次,利用304不锈钢制作了平底孔试件 并预埋了四种不同物质并进行了实验,给出在不同条件下对缺陷深度、热扩散系数或缺陷界面热波 反射系数测量的结果.实验结果显示实际测量值与其他方法测量值基本符合, 误差范围在±5%以内, 并讨论了影响测量精度的原因.     

碳纤维复合材料内部缺陷深度的定量红外检测

利用脉冲红外热成像技术对碳纤维复合材料试件内部的模拟脱黏缺陷的深度进行测量, 研究在被测物热属性参数未知情况下,碳纤维增强塑料中缺陷深度的测量方法. 分析了平板材料在脉冲热源激励下的一维热传导模型;给出了内部缺陷深度的红外测量原理; 选用对数温度二阶微分峰值时刻作为特征时间测量缺陷深度; 考虑单点标定测量深度可能产生较大的随机误差,提出利用最小二乘法多项式拟合建立阶梯件中阶梯深度与其对应的对数温度时间二阶微分曲线峰值时间两者之间的标定关系式的方法, 选择在相对误差平方和最小情形下的拟合关系式作为脱黏缺陷深度测量的标定关系式. 实验结果表明,利用该方法测量脱黏缺陷深度的精度优于单点法标定测量结果, 实现了在被检测材料热属性参数未知的情况下仍能较准确地测量脱黏缺陷深度.     

电火花直读光谱法测定低合金钢中碳的测量不确定度评定

本文根据最小二乘法原理拟合校准曲线，给出了非线性回归拟合引入的测量不确定度的估计方法并应用于电火花直读光谱法测定低合金钢中碳的测量不确定度评定，结果与经验值相吻合。     

碳碳复合阴极在相对论速调管放大器中的应用

研制了一种碳纤维分布具有高取向性的碳碳复合材料, 并采用该材料制作的阴极开展了相对论速调管放大器的实验研究。实验结果表明：碳碳复合阴极爆炸发射的点火机制以尖端场增强为主, 运行1000发后碳纤维结构稳定, 重复频率25 Hz运行时输出微波功率大于1 GW, 脉冲宽度大于100 ns, 阴极发射电流密度约3.82 kA/cm2。碳碳复合阴极在启动速度、电流延迟时间及阻抗特性等方面性能还有待进一步的研究。     

图像处理技术在材料表面形变测量中的应用

测量系统是针对检测碳/碳复合材料高温下的力学性能,分析碳/碳复合材料的应力应变关系所设计。介绍了基于CCD图像处理技术,测量高温下碳/碳复合材料试件形变系统的结构及工作原理。在高温下连续实时获取碳/碳复合材料试件上合作目标图像,并应用索贝尔算子准确的计算出图像边缘,通过坐标变换得到了碳/碳复合材料在高温载荷下形变数值。分析了测量系统中图像处理的设计思路,给出了实验结果曲线。     

CO2及其碳同位素比值高精度检测研究

改进了一种基于傅里叶变换红外光谱法测量CO₂气体的装置, 改进后的装置能够提高CO₂检测精度, 并能同时测量CO₂碳同位素比值. 研究了温度和压力对CO₂浓度值和CO₂碳同位素比值测量的影响规律. 利用该装置连续测量了标准CO₂气体和环境大气, 对标准CO₂气体测量得到的CO₂浓度值及其碳同位素比值进行温度和压力影响修正, 获得了较好的精度和准确度. 关键词： 光谱学 同位素比值 傅里叶变换红外光谱 二氧化碳     

碳碳复合阴极在相对论速调管放大器中的应用北大核心CSCD

研制了一种碳纤维分布具有高取向性的碳碳复合材料,并采用该材料制作的阴极开展了相对论速调管放大器的实验研究。实验结果表明:碳碳复合阴极爆炸发射的点火机制以尖端场增强为主,运行1000发后碳纤维结构稳定,重复频率25Hz运行时输出微波功率大于1GW,脉冲宽度大于100ns,阴极发射电流密度约3.82kA/cm2。碳碳复合阴极在启动速度、电流延迟时间及阻抗特性等方面性能还有待进一步的研究。     

应用于碳同位素丰度测量的激光频率刻度系统研究

对应用于激光吸收光谱法碳同位素丰度测量中的激光频率实时刻度系统进行研究. 采用不同自由光谱范围的共焦法布里-珀罗干涉仪对测量过程中的激光扫描频率进行实时测量. 分别采用线性内插法和多项式拟合法对激光频率每次扫描过程中的频率非线性进行分析,通过对4976–4980 cm^-1波段CO₂吸收谱的多次测量平均的实验结果与HITRAN-2008数据库相应的吸收峰数据进行比较,得到两种方法的激光频率刻度精度均可达到10^-4 cm^-1,线性内插法的刻度精度要好于多项式拟合法. 验证了激光频率实时刻度系统在碳同位素丰度测量中应用的可行性. 关键词： 激光频率实时刻度 共焦法布里-珀罗干涉仪 同位素丰度测量 激光吸收光谱法     

利用直接激发Rayleigh表面波的方法测量材料的声学非线性系数

提出了利用直接激发Rayleigh表面波的方法测量材料的声学非线性系数.采用专门的信号源,将压电传感器安装在试件边缘直接激发Rayleigh表面波,利用激光干涉仪测量系统采集试件表面的Rayleigh波信号.对采集到的Rayleigh波信号进行FFT变换,得到Rayleigh波信号中所包含的基频和高频成分,并据此进一步确定材料的声学非线性系数.对铝合金材料AA2024和AA6061的试验测量与分析结果表明,这种利用将压电传感器直接安装在试件边缘激发Rayleigh表面波的方法能够有效、准确地测量材料的声学非线性系数,可以为材料和结构早期力学性能退化的无损检测和评价提供一种有效的途径.     

碳/碳复合材料在直拉单晶硅生产中的应用

单晶硅是太阳能电池的基础材料, 在直拉法单晶硅生产工艺中需要使用大量的等静压石墨材料制作热 场, 随着单晶硅生产规模的扩大和所用热场日渐大型化, 应用新型的碳/碳复合材料制作单晶炉热场成为必然趋 势. 碳/碳复合材料适合于制作大尺寸耐高温热场, 并且使用寿命长、 稳定性高、 节能效果好     

Inspection on SiC coated carbon–carbon composite with subsurface defects using pulsed thermography

An investigation on SiC coated carbon–carbon (C/C) composite plates has been undertaken by pulsed thermography. The heat transfer model has been built and the finite element method (FEM) is applied to solve the thermal model. The simulation results show that defects with DA/DP smaller than one can hardly be detected by an infrared camera with the sensitivity of 0.02 °C. Certificated experiments were performed on the built pulsed thermography system. The thermal wave signals have been processed by subtracting background image method (SBIM), pulsed phase thermography (PPT), and temperature–time logarithm fitting method (TtLFM). The limit DA/DP of defects in SiC coated C/C composite plates with the thickness of 6 mm that can be detected by pulsed thermography with the presented signal analysis algorithms has been obtained.     

Study on thermal diffusivity of materials by laser photothermal reflection technique

A method of measuring thermal diffusivity of materials at room temperature by photothermal reflection technique is described. An intensity-modulated Ar+ laser beam is used as incident light. The beam is focused to about 1 mm diameter spot and illuminates the sample surface. HgCdTe infrared detector is used to receive photothermal signal. Using this technique, the photothermal signals are experimentally measured as the function of different frequencies. The thermal diffusivities can be obtained by fitting the experimental data. On the other hand, the thermal diffusivities of one-way composite and orthogonal symmetric arranged composites Al2O3/Al are measured in transverse, longitudinal and arbitrary directions. The results show that the diffusivity of one-way material decreases with the increase of the measurement angle; the diffusivity of orthogonally arranged material almost keeps the same when measurement angle changes.     

I-STMAS,a new high-resolution solid-state NMR method for half-integer quadrupolar nuclei

In complement to the previously proposed multiple-quantum magic-angle-spinning (MQMAS) and satellite transition MAS (STMAS) sequences, we describe a new two-dimensional high-resolution method, inverse-STMAS (I-STMAS) that allows second-order quadrupolar averaging. Like STMAS, I-STMAS correlates second-order quadrupole dephasing occurring on coherences related to the central transition (CT) and satellite transitions (STs), but does it in a reverse manner: CT evolves during the t₁ period while STs are detected during t₂. Although STMAS and I-STMAS are symmetric, there are some interesting and useful differences between the two methods. For example, we show that during the acquisition time t₂, it is possible to over-sample the data and then to process them to suppress the CT–CT correlation resonance.     

水泥老化过程中水动态的准弹性中子散射(QENS)谱分析

准弹性中子散射(quasi-elastic neutron scattering, QENS)实验是研究水泥老化过程中水动态的一种新颖的实验方法.本文利用老化时间分别为7, 14和30 d水泥样品的QENS谱实验数据, 通过应用四个高斯项的和的能量分辨函数R(Q, E)代替一个高斯项的能量分辨函数来改进经验扩散模型(empirical diffusion model, EDM), 再进行非线性最小二乘拟合.由此导出水泥样品中水动态的相关物理参数: 不动水数密度A, 自由水指数FWI=B₁/(A+B₁+B₂), 洛伦兹函数的半高宽Γ, 移动水跳跃之间的平均停留时间τ ₀及自扩散系数D_t, 而且可得出更为精准的QENS谱拟合曲线.拟合得到的物理参数可定量描述水泥老化过程中水动态过程, 从而为QENS实验在水泥老化过程中水动态研究的应用提供一种合理实用的谱分析方法.     

A generalized Vlasov equation

A two-special dimension electronic system characterized by a plasma parameter Γ 1 is analyzed; then, by using a rigorous non-equilibrium statistical mechanical theory, the evolution of distribution function is considered. A generalized Vlasov equation (GVE) is derived. Compared to the usual Vlasov equation, GVE presents an additional velocity-dependent correlation term. Taking as a starting point the GVE, the phenomenological approximation to two-particles function, ƒ₂(r₁r₂p₁p₂; t) = ƒ₁(r₁p₁;t)f₁(r₂p₂;t)g(r₁−r₂), proposed by Singwi, Tosi, Landi and Sjolander is analyzed.     

Computer simulation of the carbon diffusivity in austenite

Tracer carbon diffusion in austenite is formulated in terms of a f.c.c. lattice gas model in which carbon interstitials repel at the distance of nearest neighbors. A Monte Carlo method is used to calculate the tracer carbon diffusivity as a function of composition and interaction energy. The computed diffusivities are discussed in relation to the experimentally determined diffusivities and the results of a model investigated by Parris and McLellan.     

多层薄膜瞬态热弹反射光栅实验及其理论分析和有限元数值计算

多层薄膜/基片材料的热学性质受各层薄膜及基片的共同影响,因此同时评估各层材料的热学性质是非常重要的。激光诱导瞬态热栅技术是一种研究材料表面及亚表面光声光热现象有效的方法,因此可用于研究多层材料的热学性质。本文利用瞬态热弹反射光栅方法研究多层薄膜/基片结构材料的热扩散率,首先对Al/ZnO/Si基片结构的多层材料进行激光诱导瞬态热栅的光衍射检测实验,然后通过对该瞬态热栅的光衍射强度信号进行理论分析及有限元数值模拟,得到Al/ZnO/Si各层热扩散率对其表面温度场分布的影响,进而计算铝膜和氧化锌膜热扩散率对瞬态热栅引起衍射光信号的贡献。最后将理论分析与实验结果进行多参数拟合,在基片的参量已知的情况下,可同时得到铝膜和氧化锌膜的热扩散率。     

碳纳米管电缆式复合材料的热导率

通过非平衡分子动力学方法, 对单壁碳管填充金纳米线的碳纳米管电缆式复合材料开展热导率的模拟分析. 采用Tersoff势函数描述碳-碳原子间的相互作用, Lennard-Jones长程作用势描述碳-金原子间的相互作用, 嵌入原子势函数描述金-金原子间相互作用. 研究结果表明: 相同尺寸下, 金纳米线的电子热导率相较于空碳管以及电缆式复合材料的声子热导率小很多, 对复合材料总热导率的贡献可以忽略; 由于管内金纳米线的存在, 其与碳管的相互作用使得碳管碳原子倾向于沿着轴向振动, 声子间U散射随之减少, 声子平均自由程增加, 导致复合材料热导率明显大于空碳管, 在100–500 K温度范围内高出约20%–45%, 但增大幅度随温升呈降低趋势; 复合材料热导率随着管长增加而增大, 变化趋势和空碳管相似, 但其增长幅度更大; 复合材料和空碳管的热导率随管径增大而减小, 且变化幅度基本一致. 关键词： 碳纳米管 纳米线 电缆式复合材料 导热     

Thermal Diffusivity of Film/Substrate Structures Characterized by Transient Thermal Grating Method

Transient thermal grating method is used to measure the thermal diffusivity of absorbing films deposited on transparent substrates. According to periodically modulated dielectric constant variations and thermoelastic deformations of the thin films caused by the transient thermal gratings, an improved optical diffraction theory is presented. In the experiment, the probing laser beam reflectively diffracted by the thermal grating is measured by a photomultiplier at different grating fringe spaces. The thermal diffusivity of the film can be evaluated by fitting the theoretical calculations of diffraction signals to the experimental measured data. The validity of the method is tested by measuring the thermal diffusivities of absorbing ZnO films deposited on glass substrates.