ZnO薄膜的光抽运紫外激射

采用等离子体增强MOCVD方法生长出高质量的ZnO薄膜,并观察到了ZnO薄膜的光抽运紫外激射现象。在不同激发强度下进行了光荧光谱测量,发现紫外发光强度随着激发光强度的增加呈直线增强,证明此紫外发光峰来源于带边自由激子辐射复合。激发的激光器为3倍频YAG激光器,脉宽15ps,每秒10个脉冲。抽运光达到样品的光斑直径约为25μm,激射阈值为0．28μJ,利用光纤连接到CCD来探测接收激射光。在385～390nm之间的激射峰,其半峰全宽为0．03nm。所观察到的激射没有固定的方向,也就是说是往各个方向发射的。对于ZnO薄膜,由于我们并没有制作通常激光器的谐振腔,激射是通过晶粒强烈的散射导致的自形成谐振腔所产生的。     

脉冲激光沉积(PLD)法生长高质量ZnO薄膜及其发光性能

采用脉冲激光沉积(PLD)法在单晶Si(100)衬底上生长ZnO薄膜,以X射线衍射(XRD)、原子力显微镜(AFM)和透射电镜(TEM)等手段分析了所得ZnO薄膜的晶体结构和微观形貌。优化工艺(700℃,20Pa)下生长的ZnO薄膜呈c轴高度择优取向,柱状晶垂直衬底表面生长,结构致密均匀。室温光致发光(PL)谱分析结果表明,随着薄膜生长时O₂分压的增大,近带边紫外发光峰与深能级发光峰之比显著增强,表明薄膜的结晶性能和化学计量比都有了很大的改善。O₂分压为20Pa时所生长的ZnO薄膜具有较理想的化学计量比和较高的光学质量。     

脉冲激光沉积方法制备ZnO薄膜生长参量对发光特性的影响

用脉冲激光沉积（PLD）方法在Si（111）衬底上制备了ZnO薄膜。以325nmHe-Cd激光器为光源对薄膜进行了荧光光谱分析,用X射线衍射仪（XRD）和原子力显微镜（AFM）分别对薄膜的结构和形貌进行了分析。脉冲激光沉积方法的主要生长参量为氧压、激光重复频率、生长温度和激光能量。通过控制这些参量变量,研究了这些参量对ZnO薄膜发光特性的影响,得到了用于紫外发光的ZnO薄膜生长的优化条件：发现在温度为650℃左右、氧压50Pa左右、频率5Hz左右的范围内能得到半峰全宽较窄,强度较大的紫外发光峰。分析认为紫外峰主要是由激子辐射复合发光形成的,绿光带主要和Ozn的存在密切相关,氧空位是蓝光发射的重要原因。     

氧气流量对脉冲激光沉积ZnO薄膜的形貌及光学性质影响

使用脉冲激光沉积(PLD)方法在石英(SiO2)和单晶Si(111)基底上制备了具有高c轴择优取向的ZnO薄膜。测试结果显示:在30～70sccm氧气流量范围内,氧气流量50sccm时制备的ZnO薄膜具有较好的结晶质量、较高的光学透过率(≥80%)、较高的氧含量(～40.71%)、较快的生长速率(～252nm/h)和较好的发光特性:450～580nm附近发射峰最弱,同时～378nm附近的紫外发光峰最强,表明薄膜材料中含有较少的氧空位等缺陷。     

生长条件对脉冲激光沉积制备ZnO：Al薄膜光电性能的影响

本文研究了脉冲激光沉积(PLD)生长过程中, 铝掺量、氧压及衬底温度等实验参数对ZnO:Al(AZO)薄膜生长的影响, 并利用扫描电子显微镜、原子力显微镜、X射线衍射、霍尔效应、光透射光谱等实验手段对其透明导电性能进行了探讨. 变温霍尔效应和光透射测量表明, 当靶材中铝掺量大于0.5 wt%时, 所制备AZO薄膜中铝施主在80 K时已完全电离, 因Bernstein-Moss (BM) 效应其带隙变大, 均为重掺杂简并半导体. 进一步系统研究了氧压和衬底温度对AZO薄膜透明导电性能的影响, 实验发现当氧压为1 Pa, 衬底温度为200 ℃时, AZO 导电性能最好, 其霍尔迁移率为28.8 cm²/V·s, 薄膜电阻率最小可达2.7×10^-4 Ω·cm, 且在可见光范围内光透过率超过了85%. 氧压和温度的增加, 都会导致薄膜电阻率变大. 关键词： 脉冲激光沉积法 ZnO：Al薄膜 透光性 导电性     

ZnO薄膜近带边紫外发光的研究

用ZnO陶瓷靶,采用脉冲激光沉积(PLD)技术在c-Al₂O₃衬底上制备了ZnO薄膜。通过不同温度下光致发光(PL)光谱的测量,对样品的紫外发光机理进行研究。 在较低温度(10 K)下的PL光谱中,观测到一个位于3.354 eV处的束缚激子(D⁰X)发射,随着温度的升高(~50 K),在D⁰X的高能侧观测到了自由激子的发射峰。在10 K温度下,3.309 eV处出现了一个较强的发光带A,此发光带强度随着温度升高先增大然后减小,并且一直延续到室温。重点讨论了此发光带的起源,并认为A带可归属于自由电子-受主之间的复合发射。     

脉冲激光气相沉积法制备钴纳米薄膜实验研究

 采用脉冲激光沉积技术制备了钴纳米薄膜，分析和讨论了不同背景气压和脉冲频率对钴纳米薄膜表面形貌的影响及纳米微粒的形成机理。实验结果表明：在低背景气压下，等离子体羽辉自身粒子之间的碰撞占主导作用，容易形成液滴；在较高背景气压下，等离子体羽辉边缘粒子和背景气体粒子之间的碰撞占主导作用，容易形成小岛并凝聚成微颗粒；在4Hz的脉冲重复频率和5Pa背景气压下生长出单分散性良好的钴纳米颗粒。     

脉冲激光气相沉积法制备钴纳米薄膜实验研究

采用脉冲激光沉积技术制备了钴纳米薄膜,分析和讨论了不同背景气压和脉冲频率对钴纳米薄膜表面形貌的影响及纳米微粒的形成机理。实验结果表明：在低背景气压下,等离子体羽辉自身粒子之间的碰撞占主导作用,容易形成液滴;在较高背景气压下,等离子体羽辉边缘粒子和背景气体粒子之间的碰撞占主导作用,容易形成小岛并凝聚成微颗粒;在4Hz的脉冲重复频率和5Pa背景气压下生长出单分散性良好的钴纳米颗粒。     

利用脉冲激光沉积法制备高Mg掺杂的六方相MgZnO薄膜

选用Mg0.2Zn0.8O陶瓷靶,利用脉冲激光沉积(PLD)法,在单晶Si(100)和石英衬底上生长了一系列MgZnO薄膜(MZO)。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线能谱(EDS)和紫外可见光透射光谱(UV-Vis)等实验手段,研究了在不同工作压强下生长的薄膜样品的晶体结构、微观形貌和光学性能的变化。结果表明:所有的薄膜样品都是单一的ZnO六方相,禁带宽度随生长压强的升高而增加,变化范围在3.83～4.05eV之间,最短吸收边接近300nm。     

脉冲激光气相沉积法制备的非晶CH薄膜特性分析

采用脉冲激光气相沉积(PLD)法,研究了氢气压强对非晶CH薄膜性能的影响。原子力显微镜图和白光干涉图显示,薄膜表面平整致密,随着氢气压强增大,粗糙度变大。拉曼光谱分析表明,氢气压强增加,G峰和D峰位置都在向高波数方向移动。傅里叶变换红外光谱分析显示,薄膜中存在sp3—CH2和sp2—CH等基团。最后,采用PLD漂浮法在最优参数氢气压强为0.3 Pa下,成功制备了不同厚度(100~300 nm)、满足一定力学强度、无明显宏观缺陷的自支撑CH薄膜。     

Optically and electrically pumped random lasing from ZnO films annealed at different temperatures

We have investigated the optically and electrically pumped random lasing (RL) actions in ZnO films annealed at low and high temperatures respectively. While the optically pumped RL threshold for the ZnO film annealed at a low temperature, which features stronger light scattering and larger optical loss, is far higher than that for the ZnO film annealed at a high temperature, the electrically pumped RL threshold currents for the two ZnO films are almost the same with the electrical pumping scheme of metal-insulator-semiconductor structure. It is suggested that if the lasing region within the ZnO film is narrow enough in the case of electrical pumping, the strong light scattering can substantially alleviate the adverse effect of large optical loss on the onset of RL.     

Flexible electrically pumped random lasing from ZnO nanowires based on metal–insulator–semiconductor structure

Flexible electrically pumped random laser(RL) based on ZnO nanowires is demonstrated for the first time to our knowledge. The ZnO nanowires each with a length of 5 μm and an average diameter of 180 nm are synthesized on flexible substrate(ITO/PET) by a simple hydrothermal method. No obvious visible defect-related-emission band is observed in the photoluminescence(PL) spectrum, indicating that the ZnO nanowires grown on the flexible ITO/PET substrate have few defects. In order to achieve electrically pumped random lasing with a lower threshold, the metal–insulator–semiconductor(MIS) structure of Au/SiO_2/ZnO on ITO/PET substrate is fabricated by low temperature process. With sufficient forward bias, the as-fabricated flexible device exhibits random lasing, and a low threshold current of ～ 11.5 m A and high luminous intensity are obtained from the ZnO-based random laser. It is believed that this work offers a case study for developing the flexible electrically pumped random lasing from ZnO nanowires.     

Growth and characterization of pulsed laser deposited ZnO thin films

One of the most important and promising materials from metal oxides is ZnO with specific properties for near UV emission and absorption optical devices. The properties of ZnO thin films strongly depend on the deposition method. Among them, pulsed laser deposition (PLD) plays an important role for preparing various kinds of ZnO films, e.g. doped, undoped, monocrystalline, and polycrystalline. Different approaches — ablation of sintered ZnO pellets or pure metallic Zn as target material are described. This contribution is comparing properties of ZnO thin films deposited from pure Zn target in oxygen atmosphere and those deposited from sintered ZnO target. There is a close connection between final thin film properties and PLD conditions. The surface properties of differently grown ZnO thin films are measured by secondary ion mass spectrometry (SIMS), atomic force microscopy (AFM) and scanning electron microscopy (SEM). Furthermore, different approaches — ablation of sintered ZnO pellet or pure metallic Zn as target materials are described. The main results characterize typical properties of ZnO films versus technological parameters are presented. Presented at 5-th International Conference Solid State Surfaces and Interfaces, November 19–24, 2006, Smolenice Castle, Slovakia     

Self-catalyst synthesis of aligned ZnO nanorods by pulsed laser deposition

High-density well-aligned ZnO nanorods were successfully synthesized on ZnO-buffer-layer coated indium phosphide (InP) (100) substrates by a pulsed laser deposition (PLD) method. Scanning electron microscopy images show that the ZnO buffer layer formed uniform drip-like structure and ZnO nanorods were well-oriented perpendicular to the substrate surface. The sharp diffraction peak observed at 34.46° in X-ray diffraction scanning pattern suggests that the ZnO nanorods exhibit a (002)-preferred orientation. The PL spectra of ZnO samples shows a strong near band edge emission centered at about 380 nm and a weak deep level emission centered at around 495 nm, and it demonstrates that the ZnO nanorods produced in this work have high optical quality, which sheds light on further applications for nanodevices. Supported by the National Natural Science Foundation of China (Grant No. 50532080), the Science & Technology Foundation for Key Laboratory of Liaoning Province (Grant No. 20060131), and the Doctoral Project by China Ministry of Education (Grant No. 20070141038)     

脉冲激光气相沉积法制备的非晶CH薄膜特性分析

采用脉冲激光气相沉积(PLD)法,研究了氢气压强对非晶CH薄膜性能的影响。原子力显微镜图和白光干涉图显示,薄膜表面平整致密,随着氢气压强增大,粗糙度变大。拉曼光谱分析表明,氢气压强增加,G峰和D峰位置都在向高波数方向移动。傅里叶变换红外光谱分析显示,薄膜中存在sp3—CH2和sp2—CH等基团。最后,采用PLD漂浮法在最优参数氢气压强为0.3 Pa下,成功制备了不同厚度（100~300 nm）、满足一定力学强度、无明显宏观缺陷的自支撑CH薄膜。     

脉冲激光沉积无氢钨掺杂类金刚石膜的摩擦与机械性能

采用脉冲激光沉积技术制备出无氢钨掺杂非晶态类金刚石膜.膜中的钨含量与靶材中的钨含量保持稳定的线性关系,显示了脉冲激光沉积在难熔金属掺杂技术方面的亮点.由于碳-钨结构的形成和表面粗糙度影响,膜层的干摩擦系数随着钨含量的增加显现出先减后增的趋势,钨含量为9.67 at.％时达到最低值0.091.钨含量的增大降低了类金刚石膜...     

脉冲激光沉积动力学研究进展

脉冲激光沉积技术是现代常用的先进薄膜材料制备技术之一.文章在简要介绍脉冲激光沉积技术及其进展的基础上,较全面地介绍了脉冲激光沉积动力学的基本物理图像和动力学构架,深入地探讨了激光烧蚀靶材过程、等离子体膨胀过程和薄膜沉积过程的动力学规律,阐述了我国学者在脉冲激光沉积动力学研究方面的贡献,例如包括脉冲激光沉积三个工艺过程自洽的统一模型,等离子体膨胀的冲击波模型,基于局域能量动量守恒定律的新等离子体演化动力学模型,包括热源项、蒸发项、等离子体屏蔽效应和动态物性参数的烧蚀热传导模型,考虑电子碰撞效应和能带结构变化的修正双温模型,能统一描写从纳秒级到飞秒级脉冲激光烧蚀规律的统一双温模型等.     

脉冲激光制膜过程中等离子体演化规律的研究

利用有限差分法对脉冲激光沉积(PLD)技术制备KTa065Nb035O3(KTN)薄膜过程中等离子体在等温和绝热两个阶段的速度演化进行了模拟，并给出了其中主要粒子在空间的具体演化规律，对等离子体在空间膨胀的物理机制，进行了深入的讨论，给出了相应演化过程的物理图像，并揭示了等离子体羽辉在膨胀过程中呈现椭球外形的内在原因.     

Effects of deposition temperature on the structural and morphological properties of thin ZnO films fabricated by pulsed laser deposition

ZnO thin films were grown on Si(1 0 0) substrates using pulsed laser deposition in O₂ gas ambient (10 Pa) and at different substrate temperatures (25, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using XRD, AFM and SEM. At substrate temperature of T=150 °C, a good quality ZnO film was fabricated that exhibits an average grain size of 15.1 nm with an average RMS roughness of 3.4 nm. The refractive index and the thickness of the thin films determined by the ellipsometry data are also presented and discussed.