一维单轴式超声悬浮的实验研究

由声波发射端和反射端构成超声谐振系统,其发射端和反射端间形成超声驻波.在波节处声辐射压的合力可以悬浮微重力样品,称为单轴式超声悬浮;是一种有望成为具有应用价值的无容器处理技术.作者在参加物理第二课堂活动中,对此作了初步的实验研究,成功地悬浮起发泡材料等小物体以及蚂蚁等小动物,并观察研究了它们的悬浮姿态.     

用于电响应红外反射窗的液晶聚合物薄膜特性研究

提出了一种红外反射器件,通过载体液晶在电场下的转向控制胆甾型液晶聚合物粒子在器件中的排布方向,实现红外反射与透射之间切换.其中,胆甾型液晶聚合物粒子是实现红外反射关键.介绍了胆甾型液晶聚合物薄膜的制备方法,并采用超声波破碎的方法制备液晶粒子.研究了液晶混合物中不同比例的交联剂液晶1对液晶聚合物薄膜脆性和反射波段的影响,发现当液晶1占100%时,液晶聚合物薄膜的脆性最大,且其清亮点最高,并且薄膜的反射波段随着液晶1比例的增加而向短波方向偏移.同时,研究了薄膜厚度对液晶聚合物粒子的影响,发现液晶薄膜厚度越小,制备的液晶聚合物粒子越小且越均匀,其制成的器件电驱动性更好.该研究有利于帮助电响应红外反射窗的性能优化.     

激光对运动圆柱体加热的几何学研究

 当激光无论从地面或是从空中辐照运动的圆柱体时，都涉及到入射激光相对于圆柱体的辐照方式。在一定假设下，导出了激光对抛射圆柱体表面加热时圆柱表面热加载功率密度分布公式，并结合一理想情况，针对光束入射角度因子、光斑中心的偏移、光斑形状的变化进行了解析计算分析。分析表明，即使圆柱体本身不做自转，圆柱体表面的光强分布中心也会发生偏移，分布也会发生变化，尤其沿圆柱体轴向的分布变化较大，必须结合实际加以细化研究。     

高温超导滤波器的低温调谐技术

本文给出了高温超导滤波器的一种低温机械调谐方法,通过调谐滤波器的电场来达到优化性能的目的.此方法可以很好的改善滤波器的性能和提高产品的合格率,使基片厚度的不均匀性以及介电常数的误差对高温超导滤波器性能的影响降到最低,从而最大程度地使测试结果和计算机仿真结果相一致.文中以一个4节的高温超导微带滤波器为例,叙述了该方法的实现过程.其带宽为15MHz,中心频率为2.868GHz,带内插损为-0.04dB,反射损耗为-21dB.文中给出了带外抑制,带内特性等的调谐结果.制备完成的超导滤波器在调谐前的性能较设计结果有较大的偏差.主要表现在带内插入损耗、反射损耗特性和带外抑制的偏差.通过调谐,带内特性和带外抑制有明显的改善.带内插入损耗由调谐前的-0.44dB改善到-0.21dB;反射损耗由调谐前低端带边的-8.2dB改善到-14.27dB,但在高频端没有改善;带外抑制由实测的-28dB最大可以改善为-47dB.理论预测该调谐方法会使通带中心频率向低频端移动,我们也观察到了该现象,中心频率向低频端最大偏移了大约3.1MHz.综合各项参数,调谐后,整体性能更接近设计结果.     

悬浮二维晶体材料反射光谱和光致发光光谱的周期性振荡现象

研究了在二氧化硅/硅衬底上制备的悬浮石墨烯以及二硫化钼的反射光谱以及悬浮二硫化钼的光致发光光谱.研究发现:悬浮多层石墨烯的反射光谱表现出明显的振荡现象,并且该振荡具有一定的周期性;振荡周期的大小不依赖于悬浮多层石墨烯的层数,而是随着衬底上沉孔深度(空气层厚度)的增加而减小.利用多重光学干涉模型可以解释这种振荡现象以及振荡周期随沉孔深度改变的变化趋势.该模型计算结果表明,只有当沉孔深度达到微米量级时这种振荡现象才会显著出现;并且可由振荡周期定量地确定出沉孔深度.对于悬浮的二硫化钼样品,其反射光谱和光致发光光谱也出现了类似的振荡现象.这表明这种振荡现象是在各种衬底上悬浮二维材料反射光谱和光致发光光谱的一种普遍性结果,也预示悬浮二维材料器件的电致发光光谱也会出现类似的振荡现象,对悬浮二维晶体材料的物理性质和器件性能研究具有一定的参考价值.     

圆柱体的空间圆锥光反射、折射与衍射

用准直或会聚激光束倾斜照射圆柱体时,其反射光、透射光(柱体透明时)、衍射光(柱体较细时)的叠加将形成以光束入射点为顶点的空间圆锥形光面(空间光锥),并且在垂直于柱体轴线方向的观察平面上投影成一圆形光环.空间光锥的形成与所选圆柱体材料及其粗细无关,只要其表面具有一定反射能力即可.空间光锥的锥角等于入射光束主光轴与圆柱体轴线夹角的2倍,与圆柱体和照射光束的直径大小及光波长无关.给出了对光纤及不同直径大小的玻璃和金属圆柱体的实验观察结果,并利用矢量图解法对其进行了详细地理论分析.进而得出,通常所谓单丝衍射图样,实际上是细丝的衍射和其表面的反射光场的叠加图样,对于透明细丝,还包括其透射光场的贡献.圆柱体的这种空间圆锥光反射和衍射原理有可能用于光束定位、成形、表面检测以及三维面形测量等 关键词： 圆柱体 空间光锥 投影光环     

低温容器中超导块材悬浮与导向性能研究

本文主要研究超导磁悬浮系统中超导块材与永磁导轨之间的相互作用力,通过浸于低温容器中的超导块材与三磁峰轨道之间不同排布方式的实验,测试不同悬浮间距的悬浮力,以及在一定场冷距离下超导块材在三磁峰轨道上方不同水平位移段的导向力。结果表明,悬浮间隙越大,超导块材中心与三磁峰轨道中心水平偏移越小,悬浮力越大;在一定悬浮间距下,超导块材与三磁峰轨道之间水平位移越大,导向力越大。     

旋转圆柱等离子体中撕裂模和Kelvin-Helmholtz不稳定性的激发特性

采用约化的磁流体力学模型,数值研究了柱位形等离子体中q剖面和极向旋转剖面对q=1撕裂模不稳定性和Kelvin-Helmholtz(K-H)不稳定性的影响.随着旋转强度的增加,m/n=1/1模被逐渐抑制,而高阶谐波模式(如m/n=2/2,m/n=3/3等)会经历四个区间:撕裂模失稳区间、撕裂模致稳区间、稳定窗口区间和K-H不稳定性激发区间.更进一步,我们发现,m/n=1/1模的增长率随旋转强度的改变与剪切层所处位置有关,并且剪切层分布在有理面内外的结果基本一致;然而高阶谐波模式却没有此类现象.另外,有理面处磁剪切越小,撕裂模越容易被剪切流抑制,并且越容易激发K-H不稳定性.     

光纤端面偏移对光纤F-P可调谐滤波器性能影响

在光纤F-P可调谐滤波器进行滤波调谐的过程中经常会出现光纤端面偏移的问题,从而导致其滤波性能下降。通过ZEMAX光学仿真软件对其光纤F-P腔部分进行仿真,模拟两光纤端面发生径向偏移和产生倾角时的情况,通过对仿真结果分析得出当发生径向偏移时将会导致光纤F-P可调谐滤波器的峰值透过率减小,插入损耗增加;在产生倾角时将会导致光纤F-P可调谐滤波器的3dB带宽增加以及阻带抑制能力减弱,而当倾角大于0.005°时其滤波性能将会发生明显衰减。     

旋转体系中湍流的LBM模拟

采用基于多松弛时间因子的格子Boltzmann方法对旋转体系中的湍流进行数值研究,考察Rossby数和Ekman数对湍流的影响,包括湍流能量及其耗散率、速度、涡结构及湍流的耗散尺度即Kolmorogov尺度和积分尺度等.研究表明,系统的旋转延缓了湍流能量的衰减速率,逐步破坏初始涡结构的均匀性,与旋转方向相反的涡逐步被抑制,并最终形成若干与旋转同向的涡柱.结果还表明,系统旋转越快,湍流的耗散尺度越小而积分尺度越大.     

On the horizontal wobbling of an object levitated by near-field acoustic levitation

A circular planar object can be levitated with several hundreds of microns by ultrasonic near-field acoustic levitation (NFAL). However, when both the sound source and the levitated object are circularly shaped and the center of the levitated object does not coincide with the source center, instability problem often occurs. When this happens, it becomes difficult to pick up or transport the object for the next process. In this study, when the center of the levitated object was offset from the source center, the moving direction of the levitated object was predicted by using the time averaged potential around the levitated object. The wobbling frequency of the levitated object was calculated by analyzing the nonlinear wobbling motion of the object. It was shown that the predicted wobbling frequencies agreed with measured ones well. Finally, a safe zone was suggested to avoid the unstable movement of an object.     

Acoustic levitation and its application in estimation of high power sound field

Acoustic levitation has been studied using airborne radiation from a high power magnetostrictive ferrite transducer of frequency 18 kHz. Spherical solid objects as well as liquid drops of varying weight and radii have been levitated under I G at the velocity antinodes of the standing waves formed with the help of a reflector. The dependence of the maximum weight of a spherical object that can be levitated on the sound pressure level and the radius of the obstacle has been studied. An attempt has been made to estimate the radiated high power sound intensity from the maximum weight of the spherical object that can be levitated.     

Contactless transport of matter in the first five resonance modes of a line-focused acoustic manipulator

The first five resonance modes for transport of matter in a line-focused acoustic levitation system are investigated. Contactless transport was achieved by varying the height between the radiating plate and the reflector. Transport and levitation of droplets in particular involve two limits of the acoustic forces. The lower limit corresponds to the minimum force required to overcome the gravitational force. The upper limit corresponds to the maximum acoustic pressure beyond which atomization of the droplet occurs. As the droplet size increases, the lower limit increases and the upper limit decreases. Therefore to have large droplets levitated, relatively flat radiation pressure amplitude during the translation is needed. In this study, using a finite element model, the Gor'kov potential was calculated for different heights between the reflector and the radiating plate. The application of the Gor'kov potential was extended to study the range of droplet sizes for which the droplets can be levitated and transported without atomization. It was found that the third resonant mode (H(3)-mode) represents the best compromise between high levitation force and smooth pattern transition, and water droplets of millimeter radius can be levitated and transported. The H(3)-mode also allows for three translation lines in parallel.     

Experimental investigation of thermal processes in the multi-ring Couette system with counter rotation of cylinders

The effect of parameters of the multi-ring Couette system with counter rotating coaxial cylinders on the process of thermal energy release in a viscous liquid filling this system is considered with regard to the problem of determining the possibility of creating the high-performance wind heat generator. The multi-cylinder rotor design allows directly conversion of the mechanical power of a device consisting of two “rotor” wind turbines with a common axis normal to the air flow into the thermal energy in a wide range of rotational speed of the cylinders. Experimental results on the measurement of thermal power released in the pilot heat generator at different relative angular speeds of cylinder rotation are presented.     

Gauss声束对离轴椭圆柱的声辐射力矩

利用部分波展开法求解得到了Gauss声束入射下刚性和非刚性椭圆柱的声散射系数,推导了一般情况下的声辐射力矩表达式.在此基础上,通过一系列数值仿真详细分析了离轴距离、入射角度和束腰半径对声辐射力矩的影响.结果表明:正向与负向声辐射力矩均可以在一定条件下存在;低频情况下刚性椭圆柱比非刚性椭圆柱更容易产生较强的声辐射力矩;特定频率的入射声场可以激发出非刚性椭圆柱不同阶的共振散射模式,因而非刚性椭圆柱的声辐射力矩峰值与频率的关系更密切;增加束腰半径有利于扩大散射截面,进而增加椭圆柱的声辐射力矩.该研究结果预期可以为利用声辐射力矩实现粒子的可控旋转和流体黏度的反演提供一定的理论指导.     

Holding characteristics of planar objects suspended by near-field acoustic levitation

The authors have found the acoustic levitation phenomenon where planar objects of 10 kg weight can be levitated near a vibration surface. This phenomenon has been studied for non-contact transportation. A circular planar object can be suspended without contacting a circular vibration plate. We have studied the holding force which acts horizontally on the levitated objects. The horizontal position of the object is stabilized by this force. In this paper, we discuss the effect of the radius of a levitated object, levitation distance, displacement amplitude of the vibration plate and the vibration mode on the suspending force.     

Theoretical and experimental examination of near-field acoustic levitation

A planar object can be levitated stably close to a piston sound source by making use of acoustic radiation pressure. This phenomenon is called near-field acoustic levitation [Y. Hashimoto et al., J. Acoust. Soc. Am. 100, 2057-2061 (1996)]. In the present article, the levitation distance is predicted theoretically by numerically solving basic equations in a compressible viscous fluid subject to the appropriate initial and boundary conditions. Additionally, experiments are carried out using a 19.5-kHz piston source with a 40-mm aperture and various aluminum disks of different sizes. The measured levitation distance agrees well with the theory, which is different from a conventional theory, and the levitation distance is not inversely proportional to the square root of the surface density of the levitated disk in a strict sense.     

Rapid crystallization from acoustically levitated droplets

This paper reports on an ultrasonic levitation system developed for crystallization from solution in a containerless condition. The system has been proven to be able to levitate droplets stably and grow crystals rapidly and freely from a levitated droplet. Crystals of four samples, including NaCl, NH(4)Cl, lysozyme, and proteinase K, were obtained successfully utilizing the system. The studies showed that the crystals obtained from the acoustically levitated droplets all exhibited higher growth rates, larger sizes, better shapes, fewer crystals, as well as fewer twins and shards, compared with the control on a vessel wall. The results indicated that containerless ultrasonic levitation could play a key role in improving the crystallization of both inorganic salts and proteins. The ultrasonic levitation system could be used as a ground-based microgravity simulation platform, which could swiftly perform crystallization and screening of crystallization conditions for space crystallization and other ground-based containerless techniques. Moreover, the approach could also be conveniently applied to researching the dynamics and mechanism of crystallization. In addition, the device could be used for the preparation of high-purity materials, analysis of minute or poisonous samples, study of living cells, environmental monitoring, and so on.     

准光激励毫米波圆波导旋转TE6 2模式产生器

 介绍了采用准光方法激励圆波导产生旋转TE_{6 2}模式的设计原理、测试方法和实验结果。该模式产生器由毫米波光学系统和开放同轴波导谐振腔系统组成:毫米波光学系统由角锥喇叭天线、双曲面反射镜、抛物面反射镜、修正抛物面反射镜等部件组成;开放同轴波导谐振腔系统由开放同轴波导谐振腔、圆波导、测试辐射喇叭天线组成。通过网络分析仪和毫米波近场自动测试系统测试表明:该模式产生器在频率为96.4 GHz附近产生的圆波导旋转TE_{6 2}模式的纯度达到97%。     

Pinch instability of a cylindrical couette flow in a nonuniform axial magnetic field

The paper addresses the linear stability to axisymmetric perturbations of an incompressible nonideal fluid between two rotating coaxial infinitely long cylinders in a nonuniform axial magnetic field. For conducting cylinders, the results for uniform and nonuniform magnetic fields are qualitatively identical. This is also observed for nonconducting cylinders in a magnetic field with a constant direction. Instability appears for nonconducting cylinders in a magnetic field with a varying direction, whose magnitude exceeds a certain critical value. This new instability also exists in the absence of rotation and, hence, is independent of its parameters. In addition, the critical magnetic field is independent of the magnetic Prandtl number, which facilitates experimental observation of the new instability.