基于光子晶体异质结的高效太阳能电池反射器研究

设计了一种可用于太阳能电池反射器的二维三角晶格光子晶体异质结结构.采用传输矩阵法对该结构在可见至近红外波长范围入射电磁波的反射率进行了模拟计算,并比较了不同入射方向下反射率的变化.结果表明,光线垂直入射时,该结构光子晶体对近红外波段入射光可实现完全反射;随着偏转角度的增大,在整个可见-近红外波段均显示出极高的反射特性.该结构有望用于制作覆盖整个可见光-近红外波段的高效全方位反射器.     

基于光子晶体异质结的高效太阳能电池反射器研究

设计了一种可用于太阳能电池反射器的二维三角晶格光子晶体异质结结构.采用传输矩阵法对该结构在可见至近红外波长范围入射电磁波的反射率进行了模拟计算,并比较了不同入射方向下反射率的变化.结果表明,光线垂直入射时,该结构光子晶体对近红外波段入射光可实现完全反射|随着偏转角度的增大,在整个可见-近红外波段均显示出极高的反射特性.该结构有望用于制作覆盖整个可见光-近红外波段的高效全方位反射器.     

连续激光辐照对三结砷化镓电池散射光谱的特性影响

太阳能电池作为一种高效的光电转化器,被广泛地应用于光伏发电系统中。激光作为一种高亮度光源辐照电池时,会导致其出现损伤,可利用电池的表面散射光谱特性,对其损伤程度进行判别。通过目标表面散射光谱测量系统,对激光辐照后的三结砷化镓电池散射光谱进行测量,并计算双向反射分布函数(BRDF)。其中测量系统主要由FX 2000和NIR 17型光纤光谱仪组成,针对电池表面的强镜反射特性,在实验中采用了入射角和反射角为30°的测量几何模型。原始三结砷化镓太阳能电池的结构主要包括减反射膜DAR层、顶电池GaInP层、中电池GaAs层和底电池Ge层,其散射光谱特征包括可见光谱段(500～900 nm)的吸收特性及近红外谱段(900～1 200 nm)的类周期振荡特性,在对连续激光辐照损伤后电池的光谱特性进行实验测量后,得到了损伤电池光谱BRDF的变化,并结合基于薄膜干涉理论的电池散射光谱模型,对各膜层损伤后的特征进行了分析。结果表明：DAR层的主要作用是降低光谱反射能量,对光谱曲线的特性影响较小;Ge层对光谱曲线形状基本无影响;电池散射光谱吸收和干涉等特征主要由GaInP层和GaAs层所引起,其中,GaIn...     

带有锥度结构的同轴开槽布拉格反射器研究

本文提出在Kα波段圆柱过模结构绕射辐射器件(RDG)中引入一种带有锥度结构的同轴内开槽布拉格反射器.采用复功率守恒技术(CCPT)对该反射器的频率响应特性进行分析.研究了相位匹配段长度,波纹槽深及锥度对反射器频率响应特性的影响,分析了波纹初始相位对反射器选模特性的影响,发现该反射器具有良好的模式选择特性.本文的研究工作为同轴Bragg反射器结构的研究提供了重要的理论分析手段. 关键词： 同轴Bragg反射器 频率响应特性 复功率守恒 绕射辐射振荡器     

GaInP/GaAs/Ge三结太阳电池不同能量质子辐照损伤模拟

以GaInP/GaAs/Ge三结太阳电池为研究对象,开展了能量为0.7, 1, 3, 5, 10 MeV的质子辐照损伤模拟研究,建立了三结太阳电池结构模型和不同能量质子辐照模型,获得了不同质子辐照条件下的I-V曲线,光谱响应曲线,结合已有实验结果验证了本文模拟结果,分析了三结太阳电池短路电流、开路电压、最大功率、光谱响应随质子能量的变化规律,利用不同辐照条件下三结太阳电池最大输出功率退化结果,拟合得到了三结太阳电池最大输出功率随位移损伤剂量的退化曲线.研究结果表明,质子辐照会在三结太阳电池中引入位移损伤缺陷,使得少数载流子扩散长度退化幅度随质子能量的减小而增大,从而导致三结太阳电池相关电学参数的退化随质子能量的减小而增大.相同辐照条件下,中电池光谱响应退化幅度远大于顶电池光谱响应退化幅度,中电池抗辐照性能较差,同时中电池长波范围内光谱响应的退化幅度比短波范围更大,表明中电池相关电学参数的退化主要来源于基区损伤.     

电子辐照下GaAs/Ge太阳电池载流子输运机理研究

通过地面模拟辐照试验获得不同能量电子辐照下GaAs/Ge太阳电池电学参数退化的基本规律, 在此基础上使用PC1 D模拟程序分析太阳电池内部的载流子输运机理, 建立不同能量的电子辐照下GaAs/Ge太阳电池中多数载流子浓度和少数载流子扩散长度随辐照粒子注量变化的基本规律. 研究结果表明: 多数载流子浓度和少数载流子扩散长度均随入射电子注量的增大而减小, 多数载流子去除率和少数载流子扩散长度损伤系数均随电子能量的增高而增大, 多数载流子去除效应和少数载流子扩散长度缩短分别是电池开路电压和短路电流退化的主要原因.     

空间用倒装三结太阳能电池及其抗辐射性能研究

使用金属有机化学气相沉积技术,在4英寸GaAs衬底上获得了空间用GaInP/GaAs/In_(0.3)Ga_(0.7)As倒装三结太阳能电池.高分辨X射线衍射和阴极射线发光测试结果表明AlInGaAs应力渐变缓冲层的晶格弛豫度约100%,其整面平均穿透位错密度约5.4×10~6/cm~2.与GaInP/InGaAs/Ge常规三结太阳能电池相比,在AM0光谱、25℃测试条件下,面积24 cm~2的倒装三结太阳能电池转换效率达到32%,输出功率提高了5%.采用1 MeV高能电子对倒装三结电池进行粒子辐照测试,电池各项性能参数随不同辐照剂量发生改变,在1×10~(15)/cm~2辐照总剂量下电池转换效率衰降比例达到15%.     

基于P-N结的太阳能电池伏安特性的分析与模拟

通过分析实际P-N结与理想模型之间的差别,建立了P-N结二极管及太阳能电池的数学模型;利用Matlab中的系统仿真模块库建立仿真模型,设置参量,求解模型方程并绘制了图形.对太阳能电池在一定光照下旁路电阻及串联电阻取不同数值时对其开路电压、短路电流及填充因子的影响做了模拟,并与实际测得的硅太阳能电池伏安特性进行了比较.模型分析与实验测量的结果表明等效的旁路电阻和串联电阻分别影响电池的开路电压和短路电流.仿真结果与实验测量结果一致.     

MSM结构GaAs探测器的抗辐照性能

研究一种双金属接触的GaAs半导体探测器在14MeV中子辐照下的性能.测量了探测器经过10¹²n/cm²中子辐照剂量后的反向漏电流、电荷收集效率和最小电离粒子能谱,并且与⁶⁰Co 1.25MeV光子辐照的测量结果相比较.对中子辐照引起探测器时间性能变化和辐照损伤机制进行了探讨.并根据实验结果提出了这种双金属接触GaAs探测器灵敏层分布的一种假设,理论计算和实验数据相符合.     

基于混沌光纤激光的准分布式布拉格传感网络

提出了一种基于混沌光纤激光器的准分布式布拉格光纤光栅传感系统,将波长可调谐的混沌光纤激光器作为传感光源,全同弱反射布拉格光纤光栅作为传感元件。利用混沌光源具有delta函数的自相关特性,将混沌源的参考光信号与从全同弱反射布拉格光纤光栅反射的光信号经光电探测器进行光电转换,结合相关法对参考光和反射光进行相关运算,根据相关峰的位置对传感器位置进行精确定位。利用混沌激光的可调谐性实现因应力作用而发生变化的全同弱反射光纤光栅的中心波长的解调,从而实现准分布式的传感网络。实验结果表明利用混沌激光可在单路光纤上复用全同弱反射光纤光栅实现传感,并有望实现密集型全同弱反射光纤光栅传感网络。     

Dual-wavelength distributed Bragg reflector semiconductor laser based on composite resonant cavity

We report a monolithic integrated dual-wavelength laser diode based on a distributed Bragg reflector (DBR) composite resonant cavity. The device consists of three sections, a DBR grating section, a passive phase section, and an active gain section. The gain section facet is cleaved to work as a laser cavity mirror. The other laser mirror is the DBR grating, which also functions as a wavelength filter and can control the number of wavelengths involved in the laser action. The reflection bandwidth of the DBR grating is fabricated to have an appropriate value to make the device work at the dual-wavelength lasing state. We adopt the quantum well intermixing (QWI) technique to provide low-absorption loss grating and passive phase section in the fabrication process. By tuning the injection currents on the DBR and the gain sections, the device can generate 0.596 nm-spaced dual-wavelength lasing at room temperature.     

Dual-wavelength distributed Bragg reflector semiconductor laser based on a composite resonant cavity

We report a monolithic integrated dual-wavelength laser diode based on a distributed Bragg reflector (DBR) composite resonant cavity. The device consists of three sections, a DBR grating section, a passive phase section, and an active gain section. The gain section facet is cleaved to work as a laser cavity mirror. The other laser mirror is the DBR grating, which also functions as a wavelength filter and can control the number of wavelengths involved in the laser action. The reflection bandwidth of the DBR grating is fabricated to have an appropriate value to make the device work at the dual-wavelength lasing state. We adopt the quantum well intermixing (QWI) technique to provide low-absorption loss grating and passive phase section in the fabrication process. By tuning the injection currents on the DBR and the gain sections, the device can generate 0.596 nm-spaced dual-wavelength lasing at room temperature.     

三结太阳电池在非均匀光照下光斑强度和覆盖比率的优化研究

高倍聚光光伏组件通常采用光电转化效率较高的三结太阳电池.由于聚光器件的非理想性,电池承受的光照分布通常是高度非均匀的,在光伏组件中可通过适当增大光斑与电池面积的比率来降低光照非均匀性对电池电学性能的影响.通过对某一特定三结电池进行电路网络建模计算,分析光斑的强度分布和照射面积对电池的影响,并对比了四种设计方案(均匀光照、非均匀光照、电池效率最大、组件效率最大)下的光斑强度、光斑大小、电池效率以及电池温度分布.对比分析结果表明,组件达到效率最大时的电池效率并不是电池在标准测试条件下的最大效率,而使电池工作在效率最大值的设计方案中组件效率最低.组件效率最大方案中使用的聚光器透镜面积较小,因此该方案将导致组件成本增大.电池效率最大方案中使用的聚光器透镜面积较大并且电池温度最低,故该方案组件成本较低且可靠性较高.这表明在实际组件设计中应充分考虑对发电量的实际需求,选择合适的几何聚光倍数和光斑覆盖电池的比率.     

Spatial and spectral filtering of tapered lasers by using tapered distributed Bragg reflector grating

A 1040 nm tapered laser with tapered distributed Bragg reflector (DBR) grating is designed and fabricated. By designing the grating with tapered layout, the tapered DBR grating exhibits the scattering effect on side backward-traveling waves, thus achieving additional suppression of parasitic oscillation. Under the suppression of parasitic oscillation, the spatial and spectral characteristics of the tapered laser are improved. The experimental results show that a near-Gaussian far-field distribution and a kink-free P-I characteristics are achieved, and a single peak emission with a wavelength of 1046.84 nm and a linewidth of 56 pm is obtained.     

Modeling of resistance characteristics of a continuously-graded distributed Bragg reflector in a 980-nm vertical-cavity surface-emitting laser

The resistance characteristics of a continuously-graded distributed Bragg reflector(DBR) in a 980-nm verticalcavity surface-emitting laser(VCSEL) are modeled in detail.The junction resistances between the layers of both the p-and n-DBR mirrors are analysed by combining the thermionic emission model and the finite difference method.In the meantime,the intrinsic resistance of the DBR material system is calculated to make a comparison with the junction resistance.The minimal values of series resistances of the graded p-and n-type DBR mirrors and the lateral temperature-dependent resistance variation are calculated and discussed.The result indicates the potential to optimize the design of the DBR reflectors of the 980-nm VCSELs.     

Effects of electron radiation on shielded space and triple-junction GaAs solar cells

The displacement damage dose methodology for analysing and modelling the performance of triple-junction InGaP₂/GaAs/Ge solar cells in an electron radiation environment is presented. Degradations at different electron energies are correlated with displacement damage dose (D_\rm d). One particular electron radiation environment, relative to a geosynchronous earth orbit (GEO), is chosen to calculate the total D_\rm d behind the different thicknesses coverglasses to predict the performance degradation at the end of the 15-year mission.     

Photonic generation of microwave signal using a dual-wavelength single-longitudinal-mode distributed Bragg reflector fiber laser

In this paper, a novel all-optical microwave generation technique based on a dual-wavelength single-longitudinal-mode (SLM) distributed Bragg reflector (DBR) fiber laser is proposed and demonstrated. By exploiting spatial hole burning (SHB) effect, this laser could provide stable dual-wavelength SLM operation with a wavelength separation of 0.088 nm corresponding to the microwave signal at 10.484 GHz with a 3 dB bandwidth of 28 kHz. By appropriately adjusting the pump power, dual-wavelength oscillation could be maintained at different temperatures. We have theoretically analyzed the mechanism for microwave generation of the proposed DBR laser, and the calculated microwave frequency is in good agreement with our experimental results. Furthermore, experimental observation shows both of the laser wavelengths and generated microwave signals have good stability at room temperature.