Glass–ceramic Li2S–P2S5 electrolytes prepared by a single step ball billing process and their application for all-solid-state lithium–ion batteries

We report that glass–ceramic Li₂S–P₂S₅ electrolytes can be prepared by a single step ball milling (SSBM) process. Mechanical ball milling of the xLi₂S·(100 − x)P₂S₅ system at 55 °C produced crystalline glass–ceramic materials exhibiting high Li-ion conductivity over 10⁻³ S cm⁻¹ at room temperature with a wide electrochemical stability window of 5 V. Silicon nanoparticles were evaluated as anode material in a solid-state Li battery employing the glass–ceramic electrolyte produced by the SSBM process and showed outstanding cycling stability.     

The O–H···O, O–H···N and C–H···O hydrogen bonds in 1,4-dimethylpiperazine mono-betaine monohydrate

1,4-Dimethylpiperazine mono-betaine (1-carboxymethyl-1,4-dimethylpiperazinium inner salt, MBPZ) crystallizes as monohydrate. The crystals are orthorhombic, space group Pccn. Two MBPZ molecules and two water molecules form a cyclic oligomer, (MBPZ·H₂O)₂. The O–H···O and O–H···N hydrogen bonds are of 2.769(1) and 2.902(1) Å, respectively. The dimers interact with the neighboring molecules through the C–H···O hydrogen bonds of 3.234(1) Å. The piperazine ring assumes a chair conformation with the N(4)–CH₃ and N⁺(1)–CH₂COO⁻ groups in the equatorial position and the N⁺(1)–CH₃ group in the axial one. The FTIR spectrum is compared with that calculated by the B3LYP/6-31G(d,p) level of theory.     

Cobalt–silicon mixed oxide nanocomposites by modified sol–gel method

Cobalt–silicon mixed oxide materials (Co/Si=0.111, 0.250 and 0.428) were synthesised starting from Co(NO₃)₂·6H₂O and Si(OC₂H₅)₄ using a modified sol–gel method. Structural, textural and surface chemical properties were investigated by thermogravimetric/differential thermal analyses (TG/DTA), XRD, UV–vis, FT-IR spectroscopy and N₂ adsorption at −196 °C. The nature of cobalt species and their interactions with the siloxane matrix were strongly depending on both the cobalt loading and the heat treatment. All dried gels were amorphous and contained Co²⁺ ions forming both tetrahedral and octahedral complexes with the siloxane matrix. After treatment at 400 °C, the sample with lowest Co content appeared amorphous and contained only Co²⁺ tetrahedral complexes, while at higher cobalt loading Co₃O₄ was present as the only crystalline phase, besides Co²⁺ ions strongly interacting with siloxane matrix. At 850 °C, in all samples crystalline Co₂SiO₄ was formed and was the only crystallising phase for the nanocomposite with the lowest cobalt content. All materials retained high surface areas also after treatments at 600 °C and exhibited surface Lewis acidity, due to cationic sites. The presence of cobalt affected the textural properties of the siloxane matrix decreasing microporosity and increasing mesoporosity.     

Activation of a single-chamber solid oxide fuel cell by a simple catalyst-assisted in-situ process

Initialization is a critical processing step that has thus far limited the application of the single-chamber solid oxide fuel cell (SC-SOFC). In-situ initialization of a SC-SOFC with a nickel-based anode by methane–air mixtures was investigated. Porous Ru–CeO₂ was used as a catalyst layer over a Ni-ScSZ cermet anode. Catalytic testing demonstrated Ru–CeO₂ had high activity for methane oxidation. The Ru in the catalyst layer catalyzed the formation of syngas, which successfully reduced the nickel oxide to metallic nickel in the anode. Single cells with a La_0.8Sr_0.2MnO₃ (LSM) cathode, initialized by this in-situ reduction method, delivered peak power densities of 205 and 327 mW cm⁻² at 800 °C and 850 °C, respectively. Such performances were better than those of the cell without the Ru–CeO₂ catalyst layer that was initialized by an ex-situ reduction method were.     

Temperature-dependent interfacial properties of hydrophobically end-modified poly(2-isopropyl-2-oxazoline)s assemblies at the air/water interface and on solid substrates

We describe herein the properties at the air/water (A/W) interface of hydrophobically end-modified (HM) poly(2-isopropyl-2-oxazoline)s (PiPrOx) bearing an n-octadecyl chain on both termini (telechelic HM-PiPrOx) or on one chain end (semitelechelic HM-PiPrOx) for different subphase temperatures and spreading solvents using the Langmuir film balance technique. The polymer interfacial properties revealed by the π–A isotherms depend markedly on the architecture and molecular weight of the polymer. On cold water subphases (14 °C), diffusion of PiPrOx chains onto water takes place for all polymers in the intermediate compressibility region (5 mN m⁻¹). At higher subphase temperatures (36 and 48 °C), the HM-PiPrOx film exhibited remarkable stability with time. Brewster angle microscopy (BAM) imaging of the A/W interface showed that the polymer assembly was not uniform and that large domains formed, either isolated grains or pearl necklaces, depending on the polymer structure, the concentration of the spreading solution and the subphase temperature. The Langmuir films were transferred onto hydrophilic substrates (silica) by the Langmuir–Blodgett (LB) technique and onto hydrophobic substrates (gold) by Langmuir–Schaefer (LS) film deposition, resulting in the formation of adsorbed particles ranging in size from 200 to 500 nm, depending on the polymer architecture and the substrate temperature. The particles presented “Janus”-like hydrophilic/hydrophobic characteristics.     

Reinvestigation of the Fe-rich part of the pseudo-binary system SrO–Fe2O3

The phase relations in the Fe-rich part of the pseudo-binary system SrO–Fe₂O₃ (>33 mol% Fe₂O₃) were reinvestigated between 800 and 1500 °C in air. A combination of microscopy, electron probe micro-analysis, powder X-ray diffraction and thermal analysis was used to determine phase relations, crystal structure parameters and phase transition temperatures. M-type hexagonal ferrite SrFe₁₂O₁₉ (85.71 mol% Fe₂O₃) is stable up to 1410 °C. No indication of a significant phase width was found; Sr₄Fe₆O_13±δ appears as a second phase in compositions with <85.71±0.2 mol% Fe₂O₃. Sr₄Fe₆O_13±δ itself is stable between 800 and 1250 °C. Two other hexagonal ferrites were found to exist at high temperatures only: W-type SrFe²⁺₂Fe³⁺₁₆O₂₇ is stable between 1350 and 1440 °C and X-type ferrite Sr₂Fe²⁺₂Fe³⁺₂₈O₄₆ between 1350 and 1420 °C, respectively, which is shown here for the first time. These findings in combination with previously published data were used to derive a corrected phase diagram of the Fe-rich part of the pseudo-binary system SrO–Fe₂O₃.     

Novel co-extruded electrolyte–anode hollow fibres for solid oxide fuel cells

Novel CGO/NiO–CGO dual-layer hollow fibres (HFs) have been fabricated in a single-step co-extrusion and co-sintering process. LSCF–CGO cathodes layers were then deposited onto the dual-layer HFs to construct micro-tubular SOFCs. The NiO in the micro-tubular HF–SOFCs was reduced at 550 °C using hydrogen gas to form Ni anodes. Scanning electron microscope images showed that the dual-layer HFs have porous anodes and dense electrolyte layers. Preliminary measurements with a HF–SOFC fed with H₂ and atmospheric oxygen, produced maximum power densities of 420 W m⁻² and 800 W m⁻² at 450 °C and 550 °C, respectively.     

Synthesis and photophysical properties of novel organic–inorganic hybrid materials covalently linked to a europium complex

A novel sol–gel derived hybrid material (classed as Eu-DBM-Si) covalently grafted with Eu(DBM-OH)₃·2H₂O (where DBM-OH = o-hydroxydibenzoylmethane) was prepared through the primary β-diketone ligand DBM-OH. All the synthesized ligands were characterized by ¹H NMR, elemental analyses and Fourier transform infrared spectra (FTIR). The resultant Eu-DBM-Si material exhibited good transparent and homogenous property. Compared to the Eu-DBM hybrid prepared by physically doped silicon dioxide with Eu(DBM-OH)₃·2H₂O, the Eu-DBM-Si hybrid presented more efficient ligand-to-Eu³⁺ energy transfer and a significant improvement in the measured emission quantum yield. Furthermore, the photophysical properties of these hybrid materials, such as the photoluminescence (PL) spectra, PL intensities, symmetry properties, lifetime decays, and Judd-Ofelt parameters were also investigated in detail.     

Molybdenum(VI) network polymers based on anion–π interaction and hydrogen bonding: Synthesis, crystal structures and oxidation catalytic application

A crystallographic investigation of anion–π interactions and hydrogen bonds on the preferred structural motifs of molybdenum(VI) complexes has been carried out. Two molybdenum(VI) network polymers MoO₂F₄·(Hinca)₂ (1) and MoO₂F₃(H₂O)·(Hinpa) (2), where inca = isonicotinamide and inpa = isonipecotamide, have been synthesized, crystallographically characterized and successfully applied to alcohol oxidation reaction. Complex 1 crystallizes in the monoclinic space C2/c: a = 16.832(3) Å, b = 8.8189(15) Å, c = 12.568(2) Å, β = 118.929(3)°, V = 1560.1(5) Å³, Z = 4. Complex 2 crystallizes in the triclinic space P-1: a = 5.459(2) Å, b = 9.189(4) Å, c = 12.204(5) Å, α = 71.341(6)°, β = 81.712(7)°, γ = 77.705(7)°, V = 564.8(4) Å³, Z = 2. Complex 1 consists of hydrogen bonding and anion–π interactions, both of which are considered as important factors for controlling the geometric features and packing characteristics of the crystal structure. The geometry of the sandwich complex of [MoO₂F₄]²⁻ with two pyridine rings indicates that the anion–π interaction is an additive and provides a base for the design and synthesis of new complexes. For complex 2, the anions and the protonated inpa ligands form a 2D supramolecular network by four different types of hydrogen contacts (N–HF, N–HO, O–HF and O–HO). The catalytic ability of complexes 1 and 2 has also been evaluated by applying them to the oxidation of benzyl alcohol with TBHP as oxidant.     

TGA–FTIR study of a lead zirconate titanate gel made from a triol-based sol–gel system

A Pb(Zr,Ti)O₃ precursor gel made from a sol prepared using 1,1,1,-tris(hydroxymethyl)ethane, lead acetate and zirconium and titanium propoxides, stabilised with acetylacetone, was analysed using TGA–FTIR analysis. Decomposition under nitrogen (N₂) gave rise to evolved gas absorbance peaks at 215 °C, 279 °C, 300 °C and 386 °C, but organic vapours continued to be evolved, along with CO₂ and CO until 950 °C. The final TGA step in N₂ is thought to relate to decomposition of an intermediate carbonate phase and the final elimination of residues of triol or acetylacetonate species which form part of the polymeric gel structure. By contrast, heating in air promoted oxidative pyrolysis of the final organic groups at ≤450 °C. In air, an intermediate carbonate phase was decomposed by heating at 550 °C, allowing Pb(Zr,Ti)O₃ to be produced some 400 °C below the equivalent N₂ decomposition temperature.     

An octane-fueled low temperature solid oxide fuel cell with Ru-free anodes

A Ru-free anode was developed for the direct utilization of iso-octane in low temperature solid oxide fuel cells (SOFCs). The anode was consisted of a Ni framework and a nano-sized oxygen–ion conductor, samaria-doped ceria (SDC), which was coated onto the inner surface of the framework via an ion impregnation process. Compared with the cells based on conventional Ni–SDC anodes, single cells with the SDC-coated Ni anodes exhibited improved stability and enhanced electrochemical activity. Peak power density of 400 mW cm⁻² was achieved at 600 °C, and power generation was relatively stable over 260 h when iso-octane–air mixture was directly used as the fuel. The performance is comparable with those obtained using ceria-Ru as an internal reforming catalyst.     

Enhanced sensitivity for Cu(II) by a salicylidine-functionalized polysiloxane carbon paste electrode

A new approach for decreasing the detection limit for a copper(II) ion-selective electrode (ISE) is presented. The ISE is designed using salicylidine-functionalized polysiloxane in carbon paste. This work describes the attempts to develop the electrode and measurements of its characteristics. The new type of renewable three-dimensional chemically modified electrode could be used in a pH range of 2.3–5.4, and its detection limit is 2.7 × 10⁻⁸ mol L⁻¹ (1.2 μg L⁻¹). This sensor exhibits a good Nernstian slope of 29.4 ± 0.5 mV/decade in a wide linear concentration range of 2.3 × 10⁻⁷ to 1.0 × 10⁻³ mol L⁻¹ of Cu(II). It has a short response time (8 s) and noticeably high selectivity over other Cu(II) selective electrodes. Finally, it was satisfactorily used as an indicator electrode in complexometric titration with EDTA and determination of copper(II) in miscellaneous samples such as urine and various water samples.     

Screening method for phthalate esters in water using liquid-phase microextraction based on the solidification of a floating organic microdrop combined with gas chromatography-mass spectrometry

A simple and efficient liquid-phase microextraction (LPME) technique was developed using directly suspended organic microdrop coupled with gas chromatography–mass spectrometry (GC–MS), for the extraction and the determination of phthalate esters (dimethyl phthalate, diethyl phthalate, diallyl phthalate, di-n-butyl phthalate (DnBP), benzyl butyl phthalate (BBP), dicyclohexyl phthalate and di-2-ethylhexyl phthalate (DEHP)) in water samples. Microextraction efficiency factors, such as nature and volume of the organic solvent, temperature, salt effect, stirring rate and the extraction time were investigated and optimized. Under the optimized extraction conditions (extraction solvent: 1-dodecanol; extraction temperature: 60 °C; microdrop volume: 7 μL; stirring rate: 750 rpm, without salt addition and extraction time: 25 min), figures of merit of the proposed method were evaluated. The values of the detection limit were in the range of 0.02–0.05 μg L⁻¹, while the R.S.D.% value for the analysis of 5.0 μg L⁻¹ of the analytes was below 7.7% (n = 4). A good linearity (r² ≥ 0.9940) and a broad linear range (0.05–100 μg L⁻¹) were obtained. The method exhibited enrichment factor values ranging from 307 to 412. Finally, the designed method was successfully applied for the preconcentration and determination of the studied phthalate esters in different real water samples and satisfactory results were attained.     

Lysozyme binding to poly(4-vinyl-N-alkylpyridinium bromide)

The adsorption behavior of polycations at ionic strengths (I) ranging from 0.001 to 0.1 onto silicon wafers was studied by means of ellipsometry, contact angle measurements and atomic force microscopy (AFM). Polycations chosen were bromide salts of poly(4-vinylpyridine) N-alkyl quaternized with linear aliphatic chains of 2 and 5 carbon atoms, QPVP-C2 and QPVP-C5, respectively. Under I=0.001 the reduction of screening effects led to low adsorbed amounts of QPVP-C2 or QPVP-C5 (1.0±0.1 mg/m²), arising from the adsorption of extended chains. Upon increasing I to 0.1, screening effects led to conformational changes of polyelectrolyte chains in solution and to higher adsorbed amount values (1.9±0.2 mg/m²). Advancing contact angle θ_a measurements performed with water drops onto QPVP-C2 and QPVP-C5 adsorbed layers varied from (45±2)° to (50±5)°, evidencing the exposure of both hydrophobic alkyl groups and charged moieties. The adsorption of lysozyme (LYZ) molecules to QPVP-C5 layers was more pronounced than to QPVP-C2 films. Antimicrobial effect of LYZ bound to QPVP-C2 or QPVP-C5 layers or to Si wafers was evaluated with enzymatic assays using Micrococcus luteus as substrates. The adsorption behavior of QPVP-C2 and QPVP-C5 at the water–air interface was studied by means of surface tension measurements. Only QPVP-C5 was able to reduce water surface tension. Mixtures of LYZ and QPVP-C5 were more efficient in reducing surface tension than pure LYZ solution, evidencing co-adsorption at liquid–air interface. Moreover, antimicrobial action observed for mixtures of LYZ and QPVP-C5 was more pronounced than that measured for pure LYZ. Hydrophobic interaction between LYZ and QPVP-C5 in solution seems to drive the binding and to preserve LYZ secondary structure.     

Evaluation of time-accelerated irradiation method of elastomer by modulus–ultimate elongation profile

“Generalized modulus–ultimate elongation profile” was induced from the relationship between the modulus and the ultimate elongation of an elastomer that was quantitatively added crosslinking and scission. This profile can be used to evaluate the time-accelerated irradiation methods of ethylene-propylene-diene elastomer. The irradiation under low dose rate (0.33 kGy/h) at room temperature was the reference condition. The short-time irradiation condition was 4.2 kGy/h in 0.5 MPa oxygen at room temperature and 5.0 kGy/h in air at 70 °C. The former tended to bring about the higher ratio of scission than the reference condition; the latter tended to bring about the higher ratio of crosslinking.     

Solid substrate-room temperature phosphorimetry for the determination of trace protein using ion association complex [Cu(BPY)2]·[(Fin)2] as a phosphorescent probe

Fluorescein (HFin) emitted strong and stable room temperature phosphorescence (RTP) on filter paper after set at 50 °C for 10 min using Li⁺ as the ion perturber. HFin existed as Fin⁻ when the pH value was in the range of 5.45–7.36. Fin⁻ could react with [Cu(BPY)₂]²⁺ (BPY: α,α-bipyridyl) to produce ion association complex [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻, which could enhance the RTP signal of Hfin. In the presence of bovine serum albumin (BSA), the –COOH group of Fin⁻ in the [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻ could react with the –NH₂ group of BSA to form the ion association complex [Cu(BPY)₂]²⁺·[(Fin-BSA)₂]²⁻, which contained –CO–NH– bond. This complex could sharply enhance the RTP signal of Hfin and the ΔI_p was directly proportional to the content of BSA. According to the facts above, a new solid substrate-room temperature phosphorimetry (SS-RTP) for the determination of trace protein had been established using the ion association complex [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻as a phosphorescent probe. This method had wide linear range (0.40 × 10⁻⁹–280 × 10⁻⁹ mg l⁻¹), high sensitivity (the detection limit (LD) was 1.4 × 10⁻¹⁰ mg l⁻¹), good precision (RSD: 3.4–4.9%) and high selectivity (the allowed concentration of coexistent ions or coexistent materials was high). It had been applied to the determination of the content of protein in 10 kinds of real samples, and the result agreed well with pyrocatechol violet-Mo (VI) method (P.V.M.M.), which indicated it had high accuracy. Meanwhile, reaction mechanism for the determination of trace protein with [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻ phosphorescent probe was also discussed. The academic thought of this research could not only be used to develop many kinds of ion association complex phosphorescent probes, but also provided a new way to promote the sensitivity of SS-RTP.     

Hollow fiber membrane of yttrium-stabilized zirconia and strontium-doped lanthanum manganite dual-phase composite for oxygen separation

The hollow fiber composite membrane involving Zr_0.84Y_0.16O_1.92 (YSZ) as an oxygen ionic conductor and La_0.8Sr_0.2MnO_3−δ (LSM) as an electronic conductor was explored for oxygen separation application. The hollow fiber precursor was prepared by the phase-inversion process, and transformed to a gas-tight ceramic by sintering at 1350 °C. The as-prepared fiber exhibited a thermal expansion coefficient of 11.1 × 10⁻⁶ K⁻¹ and a three-point bending strength of 152 ± 12 MPa. An oxygen permeation flux of 2.1 × 10⁻⁷ mol cm⁻² s⁻¹ was obtained under air/He gradient at 950 °C for a hollow fiber of length 57.00 mm and wall thickness 0.16 mm. The oxygen permeation flux remained unchanged when the sweeping gas was changed from helium to high concentration of CO₂. Considering the satisfactory trade-off between the permeability and stability, the YSZ–LSM hollow fiber is promising for oxygen production applications.     

Thermodynamic excess quantities of ternary Au–Co–Pd melts by computer-aided Knudsen cell mass spectrometry

Computer-aided Knudsen cell mass spectrometry is used for the thermodynamic investigations on ternary Au–Co–Pd melts over the entire range of composition. The “digital intensity-ratio” (DIR)-method has been applied for the determination of the thermodynamic excess quantities, and the ternary thermodynamically adapted power (TAP) series concept is used for algebraic representation of the thermodynamic mixing behavior. The corresponding TAP parameters as well as the values of the molar excess Gibbs energies G^E, of the molar heats of mixing H^E, of the molar excess entropies S^E, and of the thermodynamic activities at 1800 K are presented.     

Hydrogenation of arenes, alkenes and alkynes catalyzed by a sol–gel entrapped mixture of [Rh(cod)Cl]2 and Na[HRu3(CO)11]

A sol–gel entrapped 1:3 mixture of [Rh(cod)Cl]₂ and Na[HRu₃(CO)₁₁] catalyzes the hydrogenation of various unsaturated substrates by two distinguishable mechanisms. Under 13.8 bar H₂ and 20 °C methylated arenes react rapidly to give cycloalkane derivatives. XRD and TEM studies showed that under these conditions the hydrogenation proceeds without the generation of free metal particles. The hydrogenation of non-methylated arenes, as well as that of alkenes and alkynes, require a temperature of 80–120 °C at which the entrapped complexes form metallic nano-particles of 3–5 nm. Chloroarenes are also hydrodechlorinated at 120 °C, but require a hydrogen pressure of ≥25 bar. At both temperature ranges the catalysts are reusable at least four times. The high efficiency of the hydrogenation process at 20 °C is rationalized by a synergistic effect between the two different metal atoms of the combined catalyst. This may be related to a remote control model through a hydrogen spillover mechanism.     

Preparation and electrical properties of new oxide ion conductors Ce6−xDyxMoO15−δ (0.0 ≤ x ≤ 1.8)

Ce_6−xDy_xMoO_15−δ (0.0 ≤ x ≤ 1.8) were synthesized by modified sol–gel method. Structural and electrical properties were investigated by means of X-ray diffraction (XRD), Raman, X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The XRD patterns showed that the materials were single phase with a cubic fluorite structure. Impedance spectroscopy measurement in the temperature range between 350 °C and 800 °C indicated a sharp increase in conductivity for the system containing small amount of Dy₂O₃. The Ce_5.6Dy_0.4MoO_15−δ detected to be the best conducting phase with the highest conductivity (σ_t = 8.93 × 10⁻³ S cm⁻¹) is higher than that of Ce_5.6Sm_0.4MoO_15−δ (σ_t = 2.93 × 10⁻³ S cm⁻¹) at 800 °C, and the corresponding activation energy of Ce_5.6Dy_0.4MoO_15−δ (0.994 eV) is lower than that of Ce_5.6Sm_0.4MoO_15−δ (1.002 eV).