Enhanced photoluminescence of Ca<Subscript>2</Subscript>Al<Subscript>2</Subscript>SiO<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript> by charge compensation method

The effect of compensator on optical properties of Ca₂Al₂SiO₇:Eu³⁺ is systematically investigated by the X-ray powder diffraction, photo-luminescence (PL) properties and lifetime. It is obviously observed that the PL intensity of Eu³⁺ under 394 nm excitation increases in the order of Ca_1.86Eu_0.14Al₂SiO₇ (CAS), Ca_1.72Na_0.14Eu_0.14Al₂SiO₇ (CASNa) and Ca_1.86Eu_0.14Al_2.14Si_0.86O₇ (CASAl), the intensity of Eu³⁺ are 100%, 134%, 184%, and the lifetime of Eu³⁺ are 0.75 ms, 1.28 ms and 1.39 ms, respectively. A charge compensation model is proposed to explain the changes in the emission intensity and lifetime of Eu³⁺ in Ca₂Al₂SiO₇ with different compensation methods. PACS 78.55.-m; 61.72.Ji; 61.43.Gt; 42.70.-a; 74.62.Dh     

Luminescence and energy transfer mechanism in Eu<Superscript>3+</Superscript>/Tb<Superscript>3+</Superscript>-co-doped ZrO<Subscript>2</Subscript> nanocrystal rods

Nanocrystal rods of Eu³⁺/Tb³⁺-co-doped ZrO₂ were synthesized using a simple chemical precipitation technique. Both ions were successfully doped into the Zr⁴⁺ ion site in a mixed structure containing both monoclinic and tetragonal phases. The Eu³⁺ or Tb³⁺ singly doped zirconia produced red and green luminescence which are characteristics of Eu³⁺ and Tb³⁺ ions, respectively. The co-doped zirconia samples produced blue emission from defect states transitions in the host ZrO₂, red and green luminescence from dopant ions giving cool to warm white light emissions. The phosphors were efficiently excited by ultraviolet and near-ultraviolet/blue radiations giving white and red light, respectively. The decay lifetime was found to increase with increasing donor ion concentration contrary to conventional observations reported by previous researchers. Weak quadrupole–quatdrupole multipolar process was responsible for energy transfer from Tb³⁺ (donor) ion to Eu³⁺ ion. No energy back-transfer from Eu³⁺ to Tb³⁺ ion was observed from the excitation spectra. Temperature-dependent photoluminescence shows the presence of defects at low temperature, but these defects vanished at room temperature and beyond. The Eu³⁺/Tb³⁺-co-doped ZrO₂ nanocrystal rod is a potential phosphor for white light application using UV as an excitation source. Thermoluminescence measurements show that the inclusion of Tb³⁺ ion increases trap depths in the host zirconia.     

luminescence of BaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript> crystals activated by Eu<Superscript>2+</Superscript> and Ce<Superscript>3+</Superscript> ions

We have studied the effect of doping with Eu²⁺ and Ce³⁺ ions on the photoluminescence (PL) of BaGa₂Se₄ crystals in the temperature range 77–300 K. We have established that the broad bands with maxima at wavelengths 456 nm and 506 nm observed in the photoluminescence spectra of BaGa₂Se₄:Ce³⁺ crystals are due to intracenter transitions 5d → ²F_7/2 and 5d →²F_5/2 of the Ce³⁺ ions, while the broad photoluminescence band with maximum at 521 nm in the spectrum of BaGa₂Se₄:Eu²⁺ is associated with 4f⁶ 5d → 4f⁷ (⁸S_7/2) transitions of the Eu²⁺ ion. We show that in BaGa₂Se₄:Eu²⁺,Ce³⁺ crystals, excitation energy is transferred from the Ce³⁺ ions to the Eu²⁺ ions.     

Molten salt synthesis of LaF<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> nanoplates with tunable size and their luminescence properties

A molten salt route to LaF₃:Eu³⁺ nanoplate with tunable size was developed and the products were characterized by the X-ray diffraction (XRD), transmission electron microscopy (TEM), field-emission scanning electron microscopy (FE-SEM) and high-resolution TEM (HR-TEM). It is found that the nanoplates with different sizes (ca. 46, 20, and 12 nm) could be obtained when the molar ratio of the reagents NH₄F and La(NO₃)₃ · 6H₂O was adjusted. The possible formation process of reaction was discussed, and the reasonable mechanism of size controlling was also proposed. Furthermore, the luminescent properties of all the samples with different sizes and doping levels were investigated at room temperature.     

Formation of Eu<Superscript>2+</Superscript> and Eu<Superscript>3+</Superscript> centers in synthesis of CaF<Subscript>2</Subscript>:Eu luminophores

We have studied the effect of CaF₂:Eu luminophore synthesis methods on the charge state of europium. We have shown that Eu³⁺ predominates over Eu²⁺ in samples obtained by coprecipitation of europium with calcium fluoride, and the ratio Eu³⁺/Eu²⁺ grows as the total amount of europium increases. Partial charge conversion of the europium occurs during calcination of the samples, due to changes in the excess fluorine balance. We studied the luminescence, magnetic susceptibility, and EPR of the synthesized samples. We have shown that in a solid solution, europium forms large ordered clusters, determining both the luminescent and the magnetic properties of the material. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 6, pp. 773–779, November–December, 2007.     

Spontaneous luminescence of Eu<Superscript>3+</Superscript> ions in porous Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanospheres

A study of the luminescence of Eu³⁺ ions in Y₂O₃ nanospheres indicates a significant influence of the porous structure of nanoparticles on the luminescence of dopant ions. It is shown that filling the nanopores of initially porous Y₂O₃ nanospheres shortens the decay time of the spontaneous luminescence of doping europium ions. The change in the decay time is associated with the change in the effective refractive index of the porous nanospheres.     

Synthesis and luminescent properties of Eu<Superscript>3+</Superscript>- and Eu<Superscript>2+</Superscript>-activated sodium pyrophosphate Na<Subscript>4</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

The luminescent properties of Eu³⁺ and Eu²⁺ ions in sodium pyrophosphate, Na₄P₂O₇, have been studied. The excitation spectrum of the Eu³⁺ emission in Na₄P₂O₇ consists of several sets of bands in the range 280–535 nm due to 4f–4f transitions of Eu³⁺ ions and a broad band with a maximum at about 240 nm interpreted to be due to a charge transfer (CT) transition from oxygen 2p states to empty states of the Eu³⁺ 4f⁶-configuration. Although the CT band energy is large enough, the quantum efficiency (η) of the Eu³⁺ emission in Na₄P₂O₇ under CT excitation was estimated to be very low (η ≤ 0.01). In terms of a configurational coordinate model, this fact is interpreted as a result of the high efficiency of a radiationless relaxation from the CT state to the ⁷F₀ ground state of Eu³⁺ ions occupying sodium sites in Na₄P₂O₇. A strong reducing agent is required in order to stabilize Eu²⁺ ions in Na₄P₂O₇ during the synthesis. Several nonequivalent Eu²⁺ luminescence centers in Na₄P₂O₇ were found.     

Synthesis and luminescence properties of the red phosphor CaZrO<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> for white light-emitting diode application

Eu³⁺-doped CaZrO₃ phosphor with perovskite-type structure was synthesized by the high temperature solid-state method. The samples were characterized by X-ray diffraction, scanning electron microscopy, fluorescence spectrophotometer and UV-vis spectrophotometer, respectively. XRD analysis showed that the formation of CaZrO₃ was at the calcinations temperature of 1400°C. The average diameter of CaZrO₃ with 4 mol% doped-Eu³⁺ was 2μm. The PL spectra demonstrated that CaZrO₃:Eu³⁺ phosphor could be excited effectively in the near ultraviolet light region (397 nm) and emitted strong red-emission lines at 616 nm corresponding to the forced electric dipole ⁵ D ₀ → ⁷ F ₂ transitions of Eu³⁺. Meanwhile, the light-emitting diode was fabricated with the Ca_0.96ZrO³:Eu_0.04³⁺ phosphor, which can efficiently absorb ∼ 400 nm irradiation and emit red light. Therefore Ca_0.96ZrO₃:Eu_0.04³⁺ may have applications for a near ultraviolet InGaN chip-based white light-emitting diode.     

Morphology-dependent luminescence behavior of Y<Subscript>2-x</Subscript>Gd<Subscript>x</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> thin-film phosphors grown by a laser ablation

Y_2-xGd_xO₃:Eu³⁺ luminescent thin films have been grown on Al₂O₃(0001) substrates using pulsed laser deposition. Films grown under different deposition conditions have been characterized using microstructural and luminescence measurements. The crystallinity, surface morphology and photoluminescence (PL) of the films are highly dependent on the amount of Gd present. The photoluminescence (PL) brightness data obtained from Y_2-xGd_xO₃:Eu³⁺ films grown under optimized conditions have indicated that Al₂O₃(0001) is one of the most promising substrates for the growth of high-quality Y_2-xGd_xO₃:Eu³⁺ thin-film red phosphors. In particular, the incorporation of Gd into the Y₂O₃ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with Y_1.35Gd_0.60Eu_0.05O₃, whose brightness was increased by a factor of 3.1 in comparison with that of Y₂O₃:Eu³⁺ films. This phosphor may be promising for application in flat-panel displays. PACS 78.20.-e; 78.55.-m; 78.66.-w     

Architectures of YF<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> solid and hollow sub-microspheres: a facile arginine-assisted hydrothermal synthesis and luminescence properties

Solid and hollow YF₃:Eu³⁺ spheres assembled by nanorods have been successfully synthesized via a facile arginine-assisted hydrothermal method and followed by a subsequent heat-treatment process. The experimental results reveal that the as-prepared YF₃:Eu³⁺ spheres are composed of the nanorods with a diameter of 20–50 nm and a length of 200–500 nm, the morphologies of YF₃:Eu³⁺ have been changed from solid to hollow spheres assembled by nanorods. With increase of hydrothermal temperature and time, the diameter of YF₃:Eu³⁺ spheres can be controlled from 300 to 800 nm. The solid and hollow spheres show an intense orange red emission peak near 595 nm, corresponding to the ⁵D₀ → ⁷F₁ transition of Eu³⁺. The possible formation mechanism for the hollow spheres has been presented in detail. This amine acid-assisted method is very simple, economic and environmental friendly for organic-free solvent, which would be potentially used in synthesizing other hollow materials.     

Tunable emission and efficient energy-transfer properties of Ce<Superscript>3+</Superscript> and Mn<Superscript>2+</Superscript> co-doped Ba<Subscript>3</Subscript>Gd(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> phosphors

MgO powders subjected to Q-switched laser pulses in water were characterized by X-ray/electron diffraction and optical spectroscopy to have a significant optical property change with accompanied transformation into the phase assemblages of periclase, brucite and liquid-crystalline lamella. The periclase nanoparticles tended to have {111} habit planes parallel to the basal layers of lamella and brucite flakes more or less rolled as fibers, ribbons or tubes. A significant internal compressive stress was built up for periclase and brucite but not the more flexible lamellar phase. The colloidal suspension containing the densified periclase nanoparticles within the rolled brucite/lamellae flakes showed UV–visible absorption corresponding to a minimum band gap of ca. 5 eV.     

Photolumiscent Properties of Nanorods and Nanoplates Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript>

Nanorods and nanoplates of Y₂O₃:Eu³⁺ powders were synthesized through the thermal decomposition of the Y(OH)₃ precursors using a microwave-hydrothermal method in a very short reaction time. These powders were analyzed by X-ray diffraction, field emission scanning electron microscopy, Fourrier transform Raman, as well as photoluminescence measurements. Based on these results, these materials presented nanoplates and nanorods morphologies. The broad emission band between 300 and 440 nm ascribed to the photoluminescence of Y₂O₃ matrix shifts as the procedure used in the microwave-hydrothermal assisted method changes in the Y₂O₃:Eu³⁺ samples. The presence of Eu³⁺ and the hydrothermal treatment time are responsible for the band shifts in Y₂O₃:Eu³⁺ powders, since in the pure Y₂O₃ matrix this behavior was not observed. Y₂O₃:Eu³⁺ powders also show the characteristic Eu³⁺ emission lines at 580, 591, 610, 651 and 695 nm, when excited at 393 nm. The most intense band at 610 nm is responsible for the Eu³⁺ red emission in these materials, and the Eu³⁺ lifetime for this transition presented a slight increase as the time used in the microwave-hydrothermal assisted method increases.     

Luminescence in Dy<Superscript>3+</Superscript> and Eu<Superscript>3+</Superscript> Activated K<Subscript>3</Subscript>Al<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

The Dy³⁺ and Eu³⁺ activated K₃Al₂ (PO₄)₃ phosphors were prepared by a combustion synthesis. From a powder X-ray diffraction (XRD) analysis the formation of K₃Al₂ (PO₄)₃ was confirmed. In the photoluminescence emission spectra, the K₃Al₂(PO₄)₃:Dy³⁺ phosphor emits two distinctive colors: blue and yellow whereas K₃Al₂(PO₄)₃:Eu³⁺ emits red color. Thus the combination of colors gives BYR (blue–yellow–red) emissions can produce white light. These phosphors exhibit a strong absorption between 340 and 400 nm which suggest that present phosphor is a promising candidate for producing white light-emitting diodes (LED).     

Defect Structure and Up-conversion Luminescence Properties of ZrO<Subscript>2</Subscript>:Yb<Superscript>3+</Superscript>,Er<Superscript>3+</Superscript> Nanomaterials

The up-converting ZrO₂:Yb³⁺,Er³⁺ nanomaterials were prepared with the combustion and sol–gel methods. FT-IR spectroscopy was used for analyzing the impurities. The crystal structures were characterized with X-ray powder diffraction and the mean crystallite sizes were estimated with the Scherrer formula. Up-conversion luminescence measurements were made at room temperature with IR-laser excitation at 977 nm. The IR spectra revealed the conventional and OH⁻ impurities for the combustion synthesis products. The structure of the ZrO₂:Yb³⁺, Er³⁺ nanomaterials was cubic except for the minor monoclinic and tetragonal impurities obtained with the sol–gel method. The materials showed red (650–700 nm) and green (520–560 nm) up-conversion luminescence due to the ⁴F_9/2→⁴I_15/2 and (²H_11/2, ⁴S_3/2)→⁴I_15/2 transitions of Er³⁺, respectively. The products obtained with the combustion synthesis exhibited the most intense luminescence intensity and showed considerable afterglow.     

On the Luminescence of Ce<Superscript>3+</Superscript>, Eu<Superscript>3+</Superscript>, and Tb<Superscript>3+</Superscript> in Novel Borate LiSr<Subscript>4</Subscript>(BO<Subscript>3</Subscript>)<Subscript>3</Subscript>

This paper reports on the photoluminescence (PL) and time-resolved properties of Ce³⁺, Eu³⁺, and Tb³⁺ in novel LiSr₄(BO₃)₃ powder phosphors. Ce³⁺ shows an emission band peaking at 420 nm under 350-nm UV excitation. Energy transfer from Ce³⁺ to Mn²⁺ takes place in the co-doped samples. Eu³⁺ shows red emission under near UV excitation. LiSr₄(BO₃)₃:Eu³⁺ phosphor could be a suitable candidate for phosphor-converted solid state lighting. The luminescence lifetime is 2.13 ms for Eu³⁺ in LiSr₄(BO₃)₃:0.001Eu³⁺. As Eu³⁺ concentration increasing, the decay curves deviate from exponential behavior. Tb³⁺ shows the strongest ⁵D₄→⁷ F₅ emission line at 540 nm. Decay curves of ⁵D₄→⁷ F₅ and ⁵D₃→⁷ F₅ emission with different Tb³⁺ concentrations were also measured. Cross-relaxation process is discussed based on the decay curves.     

Correction of the band gap of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> phosphor

Submicron samples of Y₂O₃:Eu³⁺ phosphor with elevated photoluminescence (PL) efficiency and activator concentration of 9 at % obtained by the sol–gel method were investigated by diffuse reflection spectroscopy and PL spectroscopy. It is found that the diffuse reflection spectrum in the vicinity of the fundamental absorption edge (<300 nm) is distorted by the superposition of the PL of Eu³⁺ ions, as a result of which the calculated value of optical band gap E _g of the Y₂O₃ matrix is overestimated. An algorithm for eliminating the PL influence on the absorption edge is proposed, and the correct E _g values are found to be 4.61 ± 0.12 and 4.50 ± 0.12 eV for annealing at 700 and 1300°C, respectively.     

Luminescence thermometry using Gd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript>

In this paper we study the possibility of using the synthesized nanopowder samples of Gd₂Zr₂O₇:Eu³⁺ for temperature measurements by analyzing the temperature effects on its photoluminescence. The nanopowder was prepared by solution combustion synthesis method. The photoluminescence spectra used for analysis of Gd₂Zr₂O₇:Eu³⁺ nano phosphor optical emission temperature dependence were acquired using continuous laser diode excitation at 405 nm. The temperature dependencies of line emission intensities of transitions from ⁵D₀ and ⁵D₁ energy levels to the ground state were analyzed. Based on this analysis we use the two lines intensity ratio method for temperature sensing. Our results show that the synthesized material can be efficiently used as thermographic phosphor up to 650 K.     

Photoluminescence,thermoluminescence and electron spin resonance studies on Eu<Superscript>3+</Superscript> doped Ca<Subscript>3</Subscript>Al<Subscript>2</Subscript>O<Subscript>6</Subscript> red phosphors

Tricalcium aluminate doped with Eu³⁺ was prepared at furnace temperatures as low as 500°C by using the convenient combustion route and examined using powder X-ray diffraction, scanning electron microscope and photoluminescence techniques. A room-temperature photoluminescence study showed that the phosphors can be efficiently excited by UV/Visible region, emitting a red light with a peak wavelength of 616 nm corresponding to the ⁵D₀–⁷F₂ transition of Eu³⁺ ions. The phosphor exhibits three thermoluminescence (TL) peaks at 195°C, 325°C and 390°C. Electron Spin Resonance (ESR) studies were carried out to study the defect centres induced in the phosphor by gamma irradiation and also to identify the defect centres responsible for the TL process. Room-temperature ESR spectrum of irradiated phosphor appears to be a superposition of three distinct centres. One of the centres (centre I) with principal g-value 2.0130 is identified as O⁻ ion while centre II with an axially symmetric principal values g _∥=2.0030 and g _⊥=2.0072 is assigned to an F⁺ centre (singly ionized oxygen vacancy). O⁻ ion (hole centre) correlates with the TL peak at 195°C and the F⁺ centre (electron centre), which acts as a recombination centre, is also correlated to the 195°C TL peak. F⁺ centre further appears to be related to the high temperature peak at 390°C. Centre III is also assigned to an F⁺ centre and seems to be the recombination centre for the TL peak at 325°C.     

Effects of Li<Superscript>+</Superscript> co-doping on the concentration quenching threshold and luminescence of GdVO<Subscript>4</Subscript>:Eu<Superscript>3+</Superscript> nanophosphors

Europium ions (Eu³⁺) and Lithium ions (Li⁺) codoped gadolinium orthovanadate with a tetragonal phase had been successfully synthesized by an efficient hydrothermal method. X-ray diffraction (XRD), scanning electron microscopy (SEM), and photoluminescence (PL) were utilized to characterize the microstructure, morphology, and luminescent properties of as-prepared samples. The various concentrations (0～14 at.%) of Li ions were applied to investigate the effect of Li⁺ co-doping concentration on the crystalline structure, microstructure, and emission intensity of GdVO₄:Eu³⁺, Li⁺ nanophosphors. The results demonstrated that Li⁺ ion co-doping changes the lattice parameters in two different ways. Moreover, the optical photoluminescent property was obtained when the Li⁺ co-doping concentration is 10 at.%. The influence of Li⁺ co-doping on the concentration quenching effect of Eu³⁺ was discussed as well. The concentration quenching threshold of Eu³⁺ was increased distinguishably. The potential mechanism was proposed in this paper.     

Luminescence of Eu<Superscript>3+</Superscript> rare-earth ions in Lu<Subscript>2</Subscript>O<Subscript>3</Subscript> nanospheres

The kinetics of luminescence of Eu³⁺ ions in Lu₂O₃:Eu nanospheres with diameters of 100–270 nm and a small standard deviation of the size distribution <15% has been studied. A sharp decrease in the decay time of luminescence of Eu³⁺ ions in the red range with an increase in the diameter of nanospheres has been attributed to the appearance of a photon mode accelerating spontaneous luminescence, which is confirmed by the calculation of ranges of existence of whispering-gallery modes in studied nanospheres.