Luminescent properties of cadmium selenide quantum dots in fluorophosphate glasses

The optical properties of fluorophosphate glasses with CdSe quantum dots are studied. Secondary heat treatment at a temperature exceeding the glass transition temperature resulted in the formation of quantum dots with sizes of 3.7–6.2 nm. The influence of the semiconductor component concentration on the spectral-luminescent characteristics of glasses is shown. It is experimentally demonstrated that glasses with a lower CdSe concentration have a higher absolute luminescence quantum yield.     

The influence of silver ion exchange on the formation and luminescent properties of lead sulfide molecular clusters and quantum dots

PbS molecular clusters and quantum dots are formed by heat treatment in fluorophosphate glasses of the Na₂O₃–Р₂O₅–Ga₂O₃–AlF₃–ZnO(S)–PbF₂ system with different lead concentrations. PbS molecular clusters are characterized by optical absorption in the range of 300–800 nm and low quantum yields, which decrease from 8.9 to 2.7% with a semiconductor component concentration. It is shown that the parameters of formation of quantum dots luminescing in the wavelength range of 1000–1500 nm are considerably different at different semiconductor component concentrations. The influence of silver ion exchange on the formation of PbS nanoparticles is studied. Introduction of silver stimulates the growth of molecular clusters, which is seen in the absorption spectra. A possible mechanism of interaction of silver nanoparticles with PbS quantum dots is presented.     

The influence of ligand type on self-organization and optical properties of cadmium selenide quantum dots

A method for successive replacement of organic shells of colloidal cadmium selenide quantum dots (QDs) of different sizes is proposed. It is found that the spectral parameters of QD samples depend on the type of organic shells. It is shown that the structural morphology is independent of the QD size and is determined by the chemical composition of the organic shell. Spectral analysis of the luminescence of QD-based superstructures shows that the luminescence wavelength and intensity strongly depend on the degree of QD surface passivation.     

Spectroscopic properties of Sm3+ ions in lead fluorophosphate glasses

The Sm³⁺-doped lead fluorophosphate glasses of composition 44P₂O₅–17K₂O–9Al₂O₃–(24?x)PbF₂–6Na₂O–xSm₂O₃, where x=0.01, 0.05, 0.1, 0.5, 1.0 and 2.0 mol%, have been prepared by conventional melt quenching technique and are characterized through differential thermal analysis, Raman, absorption and emission spectra and decay rate measurements. Free-ion Hamiltonian model for energy level analysis and Judd–Ofelt theory for spectral intensities have been used to analyze the spectroscopic properties of Sm³⁺ ions in lead fluorophosphate glasses. The decay rates for the ⁴G_5/2 level of Sm³⁺ ions have been measured and are found to be single exponential at lower concentration (≤0.1 mol% Sm₂O₃) and turn into non-exponential at higher concentrations (≥0.5 mol% Sm₂O₃) due to energy transfer through cross-relaxation. The experimental lifetimes for ⁴G_5/2 level of Sm³⁺ ions are found to decrease from 2.54 to 0.92 ms when the concentration increased from 0.01 to 2.0 mol% Sm₂O₃ due to energy transfer. In order to know the nature of the energy transfer mechanism, the non-exponential decay rates are well fitted to Inokuti–Hirayama model for S=6, which indicates that the energy transfer process is of dipole–dipole type.     

The formation of acetylcholine receptor clusters visualized with quantum dots

Background  

Motor innervation of skeletal muscle leads to the assembly of acetylcholine receptor (AChR) clusters in the postsynaptic membrane at the vertebrate neuromuscular junction (NMJ). Synaptic AChR aggregation, according to the diffusion-mediated trapping hypothesis, involves the establishment of a postsynaptic scaffold that "traps" freely diffusing receptors into forming high-density clusters. Although this hypothesis is widely cited to explain the formation of postsynaptic AChR clusters, direct evidence at molecular level is lacking.     

The influence of the polymer-stabilizer molecular weight on the spectral luminescence properties of composite sols and coatings containing PbS quantum dots

The influence of the polyvinylpyrrolidone (PVP) molecular weight on the stability and spectral luminescence properties of sols of lead sulfide nanocrystals and the related composite coatings has been studied. It is shown that the spectral properties of PbS sols stabilized with low-molecular (PVP) and the related coatings are determined to a great extent by the formation of large particle aggregates in these materials and, accordingly, high level of light scattering. It is effective to use low-molecular PVP for preparing powder materials containing PbS quantum dots (QDs), because it allows one to perform fast powder precipitation and form small semiconductor particles. High-molecular PVP provides high aggregative and sedimentation stabilities of semiconductor nanocrystal sols. This polymer is effective for use in preparing stable QD sols and homogeneous coatings transparent in the visible spectral range.     

Spectroscopic properties of Mn2+ in new bismuth and lead contained fluorophosphate glasses

Luminescence, absorption and electron spin resonance (ESR) spectroscopic measurements are performed for two new Mn²⁺ doped fluorophosphate glass systems containing bismuth and lead, respectively, i.e., 45Ba(PO₃)₂-55BiF₃ and 45Ba(PO₃)₂-55PbF₂, to elucidate the nature of dopant–ligand bonding in terms of the covalence degree of dopant–ligand bond and ligand field strength. It is found from luminescence measurements that an octahedral coordination of dopant is formed, which is the same as that in fluoroberyllate and phosphate glasses. The optical absorption measurements indicate that the position of the absorption band, ⁴T_1g(G), is red shifted, and the Racah coefficient B is 625 and 627 cm^-1, respectively, as ligand field strength increases in the order of fluoroberyllate, fluorophosphate, phosphate and silicate glasses. The hfs constant A determined from the ESR measurements is 94.33 and 92.12 Oe for two glass systems, respectively. The hfs constant A is also found to be 89.98 Oe and 94.33 Oe in the respective crystalline and glasses 45P₂O₅-55BiF₃. In addition, the resonance observed at g2 in both glass systems is mainly attributed to Mn²⁺ ions in an environment close to octahedral symmetry distorted by agglomeration of resonant centers. It, thus, can be concluded from the ESR measurements that the degree of covalency of dopant–ligand bond in both fluoroberyllate and phosphate glasses is similar, and the crystallization of the glass leads to an increase in the degree of covalency of the ligand–Mn²⁺ bond. PACS 42.70.Ce; 61.43.Fs; 78.55.Qr     

The influence of low-temperature silver-ion exchange on the spectral-luminescent properties of fluorophosphate glasses doped with PbSe

Changes in the absorption and luminescence spectra of fluorophosphate glasses doped with PbSe caused by low-temperature Ag⁺–Na⁺ ion exchange are considered. It is found that the silver distribution gradient in a near-surface layer about 16 μm thick leads to two different processes of interaction between metal and semiconductor nanoparticles. PbSe molecular clusters and quantum dots more efficiently grow in deep layers with a low silver concentration. The near-surface glass layers with a high silver concentration exhibit formation of Ag metal nanoparticles, on the surface of which interaction with PbSe molecular clusters leads to the formation of Ag–Se–Pb bonds, which transform into Ag₂Se layers in the process of heat treatment. The appearance of the new phase is confirmed by X-ray diffraction.     

Spectral-luminescent properties of silver molecular clusters and nanoparticles formed by ion exchange in antimony-doped photo-thermo-refractive glasses

Optics and Spectroscopy - The formation of silver molecular clusters and nanoparticles in photo-thermo-refractive (PTR) glasses with different antimony contents has been investigated using ion...     

Influence of stoichiometry on the luminescent properties of InAs quantum dots grown on a heterostructure

We report photoluminescence (PL) spectra of InP/In_xGa_1-xAs/InAs/InP dot-in-a-well structures grown by MOVPE, with different compositions of the ternary layer. Measurements with atomic force microscopy showed that the largest quantum dot (QD) height is obtained when the InAs QDs are grown on the In_xGa_1-xAs layer with a mismatch of 1000 ppm, and the height decreases as the mismatch departs from this value. PL spectra of the QDs showed an asymmetric band, which involves transitions between dot energy levels and can be deconvoluted into two peaks. The highest energy PL peak of this band was observed for the sample with the QDs grown on top of the lattice-matched In_xGa_1-xAs layer and it shifted to lower energies for strained samples as the degree of mismatch increased. Theoretical calculations of the energy levels of the entire structure were used to interpret the obtained PL spectra and determine the possible detection tunability range.     

Absorption and fluorescence studies of Sm ions in lead containing sodium fluoroborate glasses

Lead containing calcium zinc sodium fluoroborate glasses (LCZSFB) with molar composition of 20PbO+5CaO+5ZnO+10NaF+(60−x) B₂O₃+x Sm₂O₃, (x=0.1, 0.25, 0.5, 1.0 and 2.0 mol%) were prepared and investigated by the XRD, FTIR, optical absorption, photoluminescence and decay curve analysis. Judd-Ofelt theory was applied to the experimental oscillator strengths to evaluate the phenomenological J-O intensity parameters Ω_λ (λ=2, 4 and 6). Using the J-O intensity parameters as well as from the emission and decay measurements, various radiative parameters such as transition probabilities (A_R), radiative lifetimes (τ_R), measured lifetimes (τ_m), calculated branching ratios (β_R), measured branching ratios (β_m), effective bandwidth (Δλ_eff) and stimulated emission cross sections σ(λ_p) have been calculated for the excited ⁴G_5/2 luminescent level. The nature of decay curves of ⁴G_5/2 level for different Sm³⁺ ion concentrations in all LCZSFB glasses has been analyzed and the lifetimes are noticed to decrease with increase of concentration. The concentration quenching has been attributed to the energy transfer through the cross-relaxation between Sm³⁺ ions. Based on these results, the utility of Sm³⁺ ions doped lead containing fluoroborate glasses as laser active materials in the visible region is discussed.     

The influence of ligands on the preparation and optical properties of water-soluble CdTe quantum dots

In a systematic investigation has been found that ligands play an important role in both the water-phase preparation and optical properties of CdTe quantum dots. Experiments were performed using three typical thioalkyl acids as ligands, namely mercaptoacetic acid (MAA), l-cysteine (Cys) and reduced glutathione (GSH). The growth rate and size-distribution of CdTe quantum dots (QDs) are shown to depend on the type of ligands. A proper choice of ligand enables to make lager nanocrystals with narrower size-distribution. The effects of pH (buffer solution), illumination, heating and cations on the spectroscopic properties of CdTe QDs for the three ligands are reported. In addition, three same-size CdTe QDs were individually characterized by micellar electrokinetic capillary electrophoresis with laser-induced fluorescent detection, which proved their monodisperse size-distribution and different electric charge distribution on the surface for each of the three different type of QDs.     

The influence of cysteamine and counterion concentrations on the properties of CdSe/ZnS quantum dots

The influence of the cysteamine surfactant concentration on the stability of CdSe/ZnS nanoparticles (NPs) solubilized by this compound at the phase interface between two immiscible liquids is considered. The steady-state and time-resolved fluorescence spectroscopy data show that the fluorescence quantum yield of cysteamine-coated NPs and their stability to aggregation in a potassium phosphate buffer are determined by the balance between the concentrations of surfactant in the aqueous phase and hydrophobic NPs in the nonpolar phase (chloroform, toluene, etc.). It is found that the brightest and most stable hydrophilic NPs can be obtained by completely coating them by cysteamine molecules without a surfactant deficit or excess in the reaction at the phase interface.     

Yb3+掺杂铝氟磷酸盐玻璃的光谱和激光性能

关键词：     

Nonlinear optical properties of sol-gel-type glasses containing oxidized Cu2Se nanoparticles

Nonlinear absorption of sol-gel-type glasses containing oxidized Cu₂Se nanoparticles (25 nm in radius) is investigated with the aid of the picosecond excitation-probing technique. The oxidation of Cu₂Se nanoparticles leads to the appearance of a wide absorption band, which has a maximum roughly at 1 μm and which is bleached on exposure to laser pulses. The time of relaxation of the bleached state approaches 300 psec, and the cross section for absorption at 1.06 μm is equal to about 1.3·10⁻¹⁶ cm², as evaluated from the measured absorption saturation curve. The regime of Q-switching is obtained for a number of solid-state lasers with generation wavelengths 1.06, 1.34, and 1.54 μm, when sol-gel-type glasses containing oxidized Cu₂Se nanoparticles were used as passive shutters. Translated from Zhurnal Prikladnoi Spektroskopii, Vol, 67, No. 2, pp. 203–207, March–April, 2000.     

Yb3+掺杂铝氟磷酸盐玻璃的光谱和激光性能

研究了Yb3 掺杂铝氟磷酸盐 (AFP)玻璃的吸收光谱、荧光光谱 ,测量了Yb3 离子的荧光有效线宽 (Δλeff>5 5nm)以及2 F5 2 能级的荧光寿命 (τmax=2ms)及随掺杂浓度的变化 .应用倒易法计算了Yb3 的发射截面 ,其发射截面可达 0 6 6 82 3pm2 ,且激光增益系数τfσemi达 1 2 89ms.pm2 .评估了Yb3 在AFP玻璃中的激光性能 ,发现其具有较理想的激发态最小粒子数 (0 15 )、饱和抽运强度 (8 3kW cm2 )和最小抽运强度 (1 2 4 5kW cm2 )值及良好的热稳定性 .研究结果表明掺Yb3 氟磷酸盐玻璃是实现高功率超短可调谐激光器的理想增益介质 .     

Spectroscopic and photoluminescence characteristics of Dy ions in lead containing sodium fluoroborate glasses for laser materials

Lead containing calcium zinc sodium fluoroborate (LCZSFB) glasses doped with different concentrations of trivalent dysprosium ions were prepared and investigated by the XRD, FTIR, optical absorption, photoluminescence and decay curve analysis. The experimentally determined oscillator strengths have been determined by measuring the areas under the absorption peaks and the Judd–Ofelt (J–O) intensity parameters were calculated using the least squares fit method. From the evaluated J–O parameters the radiative transition probability rates, radiative lifetimes and branching ratios were calculated for ⁴F_9/2 excited level. Room temperature photoluminescence spectra for different concentrations of Dy³⁺-doped LCZSFB glasses were obtained by exciting the glass samples at 386 nm. The intensity of Dy³⁺ emission spectra increases with increasing concentration of 0.1, 0.25, 0.5 and 1.0 mol% and beyond 1.0 mol% the concentration quenching is observed. The measuring branching ratios are reasonably high for transitions ⁴F_9/2→⁶H_15/2 and ⁶H_13/2, suggesting that the emission at 484 and 576 nm, respectively, can give rise to lasing action in the visible region. From the visible emission spectra, yellow–blue (Y/B) intensity ratios and chromaticity color coordinates were also estimated. The lifetimes of ⁴F_9/2 metastable state for the samples with different concentrations were also measured and discussed.     

Physical, optical, structural and gamma-ray shielding properties of lead sodium borate glasses

Lead sodium borate glasses with compositions xPbO:20Na₂O:(80−x)B₂O₃ (where x=5, 10, 15, 20, 25, 30, 35, 40, 45, 50 and 55 mol%) have been prepared using melt-quenching method and investigated on their optical, physical, structural and gamma-rays shielding properties. The densities of these glass samples were increased with increase in PbO concentration. The FTIR spectra and molar volumes indicate that PbO acts differently on this glass structures over their compositions. For the PbO composition less than 20 mol%, Pb²⁺ is incorporated as network former, while it acts as network modifier for the composition from 20-55 mol%. For gamma-ray shielding properties, parameters such as mass attenuation coefficients, effective atomic number and half value layer were increased with increase in PbO concentration. Our results showed relative difference between theory and experiment of less than 1% between experimental and theoretical values. Moreover half value layers of the glass systems have been compared with some standard radiation shielding materials and they exhibited better shielding properties than barite concrete and ferrite concrete at 15 and 25 mol% of PbO, respectively.     

Magnetic properties of quantum dots and rings

Exact many-body methods as well as current-spin-density functional theory are used to study the magnetism and electron localization in two-dimensional quantum dots and quasi-one-dimensional quantum rings. Predictions of broken-symmetry solutions within the density functional model are confirmed by exact configuration interaction (CI) calculations: In a quantum ring the electrons localize to form an antiferromagnetic chain which can be described with a simple model Hamiltonian. In a quantum dot the magnetic field localizes the electrons as predicted with the density functional approach. Received 5 December 2000