Electrochemical corrosion kinetics of tin and tin amalgams in NaCl aqueous solutions

Electrochemical techniques were used to determine the corrosion rate of pure tin metal as compared to 80 Sn/20 Hg tin amalgam. X-ray diagrams showed that this amalgam was a crystalline γ₂ phase, whereas a 50 Sn/50 Hg amalgam contained liquid alloy embedded in the same γ₂ phase. Open circuit potential measurements, combined with narrow range potential scanning voltammetry, lead to the conclusion that amalgamation resulted in enhancement of the corrosion current, mainly by increasing the cathodic electron transfer reaction kinetics both in deaerated and in oxygen-saturated NaCl solution. When maintained at zero current potential in a solution containing dissolved O₂ gas, the samples were gradually covered with an insulating oxide layer which was identified by a series of electrochemical impedance diagrams recorded at different time intervals. The oxide layer was firmly adherent to the bulk tin metal but was poor at protecting the amalgam electrode. Finally, at potential values where the anodic current reached a few mA/cm², the pure tin metal surface was suddenly deteriorated by the formation of extremely deep pinhole corrosion pits, while this effect was smoothed down by amalgamation. Electronic Publication     

Hydrothermal Synthesis of Titanium‐Supported Nickel Nanoflakes for Electrochemical Oxidation of Glucose

Titanium‐supported nanoscale flaky nickel electrode (nanoNi/Ti) was prepared by a hydrothermal process using hydrazine hydrate as a reduction agent. Its electrocatalytic activity as an electrocatalyst for the electrooxidation of glucose was evaluated in alkaline solutions using cyclic voltammetry (CV), chronoamperometric responses (CA) and electrochemical impedance spectra (EIS). The nanoNi/Ti electrode exhibits significantly high current density of glucose oxidation. A high catalytic rate constant of 1.67×10⁶ cm³ mol^?1 s^?1 was calculated from amperometric responses on the nanoNi/Ti electrode. Low charge transfer resistances on the nanoNi/Ti in 0.5 M NaOH containing various concentrations of glucose were obtained according to the analysis for EIS. Furthermore, amperometric data show a linear dependence of the current density for glucose oxidation upon glucose concentration in the range of 0.05–0.6 mM with a sensitivity of 7.32 mA cm^?2 mM^?1. A detection limit of 0.0012 mM (1.2 μM) M glucose was found. Results show that the prepared nanoNi/Ti electrode presents high electrocatalytic activity for glucose oxidation.     

Nanoporous Pt Catalyst Modified by Sn Electrodeposition for Electrochemical Oxidation of Formaldehyde

A nanoporous Pt particles‐modified Ti (nanoPt/Ti) electrode was prepared through a simple hydrothermal method using aqueous H₂PtCl₆ as a precursor and formaldehyde as a reduction agent. The nanoPt/Ti electrode was then modified with limited amounts of tin particles generated by cyclic potential scans in the range of ?0.20 to 0.50 V in a 0.01 mol·L^?1 SnCl₂ solution, to synthesize a Sn‐modified nanoporous Pt catalyst (Sn/nanoPt/Ti). Electroactivity of the nanoPt/Ti and Sn/nanoPt/Ti electrodes towards formaldehyde oxidation in a 0.5 mol·L^?1 H₂SO₄ solution was evaluated by cyclic voltammetry and chronoamperometry. Electrooxidation of formaldehyde on the nanoPt/Ti electrode takes place at a potential of 0.45 V and then presents high anodic current densities due to the large real surface area of the nanoPt/Ti electrode. The formaldehyde oxidation rate is dramatically increased on the Sn/nanoPt/Ti electrode at the most negative potentials, where anodic formaldehyde oxidation is completely suppressed on the nanoPt/Ti electrode. Chronoamperogramms (CA) of the Sn/nanoPt/Ti electrode display stable and large quasi‐steady state current densities at more negative potential steps. Amperometric data obtained at a potential step of 100 mV show a linear dependence of the current density for formaldehyde oxidation upon formaldehyde concentration in the range of 0.003 to 0.1 mol·L^?1 with a sensitivity of 59.29 mA·cm^?2 (mol·L^?1)^?1. A detection limit of 0.506 mmol·L^?1 formaldehyde was found. The superior electroactivity of the Sn/nanoPt/Ti electrode for formaldehyde oxidation can be illustrated by a so‐called bifunctional mechanism which is involved in the oxidation of poisoning adsorbed CO species via the surface reaction with OH adsorbed on neighboring Sn sites.     

Synthesis and characterization of activated carbon–ethylenediamine–cobalt(II) tetracarboxyphthalocyanine conjugate for catalytic oxidation of ascorbic acid

We report on the synthesis and characterization of activated carbon–ethylenediamine–cobalt(II) tetracarboxyphthalocyanine conjugate (AC–CONHCH₂CH₂NH₂–CoPc) and its electrocatalytic behavior for oxidation of ascorbic acid. Ultraviolet–visible (UV–Vis), Fourier-transform infrared (FTIR), and electrochemical impedance spectroscopies, and cyclic and square-wave voltammetry were used to characterize the electrode modifiers and modified glassy carbon electrode. The limit of detection was found to be 0.26 µm using 3δ notation. The linear dynamic range was from 1.5 × 10^?4 to 1 × 10^?2 M with electrode sensitivity of 0.01 A mol^?1 L cm^?2. A Tafel slope of 200.8 mV decade^?1 was found. The concentration of ascorbic acid in the tablet was 0.034 M. Oxalic acid showed no interference in ascorbic acid determination.     

Heterotermetallic Indium Lithium Halostannates: Low‐Temperature Single‐Source Precursors for Tin‐Rich Indium Tin Oxides and Their Application for Thin‐Film Transistors

The syntheses and structural elucidation of dimeric [Sn(OCyHex)₂] ( 1 ), its corresponding (cyclohexoxy)alkalistannates(II) [{M(OCyHex)₃Sn}₂] (M=Li ( 2 ), Na ( 3 ), K ( 4 )), and of the first heteroleptic heterotermetallic Li/In/Sn–haloalkoxide clusters [X₂In{LiSn₂(OCyHex)₆}] (X=Br ( 5 ), Cl ( 6 )) with a double seco‐norcubane core are reported. They represent suitable precursors for new amorphous indium tin oxide (ITO) materials as transparent conducting oxides with drastically reduced concentrations of expensive indium, while maintaining their high electrical performance. In fact, compounds 5 and 6 were successfully degraded under dry synthetic air at relatively low temperature, resulting in new semiconducting tin‐rich ITOs homogeneously dispersed in a tin oxide/lithium oxide matrix. The obtained particles were investigated and characterised by different analytical techniques, such as powder XRD, IR spectroscopy, SEM, TEM and energy‐dispersive X‐ray spectroscopy (EDX). The analytical data confirm that the final materials consist of tin‐containing indium oxide embedded in an amorphous tin oxide matrix. The typical broadening and shift of the observed indium oxide reflections to higher 2θ values in the powder XRD pattern clearly indicated that tin centres were successfully incorporated into the In₂O₃ lattice and partially occupied In³⁺ sites. Investigations by EDX mapping proved that Sn was homogeneously distributed in the final materials. Thin‐film field‐effect transistors (FETs) were fabricated by spin‐coating of silicon wafers with solutions of 5 in toluene and subsequent calcination under dry air (25–700 °C). The FETs prepared with precursor 5 exhibited excellent performances, as shown by a charge‐carrier mobility of 6.36×10^?1 cm² V^?1 s (calcination at 250 °C) and an on/off current ratio of 10⁶.     

A Novel NH2/ITO Ion Implantation Electrode: Preparation,Characterization, and Application in Bioelectrochemistry

A novel NH₂⁺ ion implantation‐modified indium tin oxide (NH₂/ITO) electrode was prepared. Acid‐pretreated, negatively charged MWNTs were firstly modified on the surface of NH₂⁺ ion implantation electrode, then, positively charged Mb was adsorbed onto MWNTs films by electrostatic interaction. The assembly of MWNTs and Mb was characterized with electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The immobilized Mb showed a couple of quasireversible cyclic voltammetry peaks in pH 7.0 phosphate buffer solution (PBS). The apparent surface concentration of Mb at the electrode surface was 1.06×10^?9 mol cm^?2. The Mb/MWNTs/NH₂/ITO electrode also gave an improved electrocatalytic activity towards the reduction of hydrogen peroxide. The catalysis currents increased linearly to the H₂O₂ concentration in a wide range from 9×10^?7 to 9.2×10^?5 M with a correlation coefficient of 0.999. The detection limit was 9.0×10^?7 M. The experiment results demonstrated that the modified electrode provided a biocompatible microenvironment for protein and supplied a necessary pathway for its direct electron transfer.     

Synthesis of Ferrocene Based Naphthoquinones and its Application as Novel Non‐enzymatic Hydrogen Peroxide

At present, a highly sensitive hydrogen peroxide (H₂O₂) sensor is fabricated by ferrocene based naphthaquinone derivatives as 2,3‐Diferrocenyl‐1,4‐naphthoquinone and 2‐bromo‐3‐ferrocenyl‐1,4‐naphthoquinone. These ferrocene based naphthaquinone derivatives are characterized by H‐NMR and C‐NMR. The electrochemical properties of these ferrocene based naphthaquinone are investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) on modified glassy carbon electrode (GCE). The modified electrode with ferrocene based naphthaquinone derivatives exhibits an improved voltammetric response to the H₂O₂ redox reaction. 2‐bromo‐3‐ferrocenyl‐1,4‐naphthoquinone show excellent non‐enzymatic sensing ability towards H₂O₂ response with a detection limitation of 2.7 μmol/L a wide detection range from 10 μM to 400 μM in H₂O₂ detection. The sensor also exhibits short response time (1 s) and good sensitivity of 71.4 μA mM^?1 cm^?2 and stability. Furthermore, the DPV method exhibited very high sensitivity (18999 μA mM^?1 cm^?2) and low detection limit (0.66 μM) compared to the CA method. Ferrocene based naphthaquinone derivative based sensors have a lower cost and high stability. Thus, this novel non‐enzyme sensor has potential application in H₂O₂ detection.     

Electrocatalytic Oxidation and Sensitive Determination of Paracetamol Based on Nanosheets Self‐assembled Lindgrenite Microflowers

In this work, the nanosheet‐assembled lindgrenite microflowers (chemical formula: Cu₃Mo₂O₉) were synthesised through a simple process and low‐cost raw materials at room temperature in aqueous solution without using any surface‐active agent. The tightly interlaced nanosheets, like petals, can increase the specific surface area, which can bring about higher electrocatalytic activity and electroanalysis sensitivity. Thus, lindgrenite microflowers were prepared as an electrochemical sensor and successfully applied in the detection of paracetamol through the modified glass carbon electrode. Furthermore, this electrochemical reaction process was simulated at the ab‐initio level to reveal the catalytic mechanism, and the simulation results agreed well with electrochemical experiments. The electrochemical performance of the lindgrenite microflowers modified glassy carbon electrode (GCE) was studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The linearity of paracetamol ranged from 0.05 to 1200 μM (IT method) and 0.05 to 1000 μM (DPV method), low detection limit (0.01 μM) and high sensitivity (5.11 mA mM^?1 cm^?2) towards paracetamol. Moreover, this sensor was applied to detect paracetamol in human blood serum samples. The excellent results demonstrated that the prepared electrode not only showed a desirable linear range towards paracetamol but also exhibited practical applicability and reliability towards human serum samples detection.     

Novel Sn Doped Co3O4 Thin Film for Nonenzymatic Glucose Bio‐Sensor and Fuel Cell

A facile chemical solution deposition via two‐step spin coating technique was used to fabricate nano‐particulate novel Sn doped Co₃O₄ thin film for glucose sensor and fuel cell applications. Substitution of Sn into Co₃O₄ host lattice lead to a remarkable increase in the electrocatalytic activity of the Co₃O₄ electrode material. Film thickness played a significant role in enhancing the charge transferability of the electrode as was observed from electrochemical impedance spectroscopy (EIS). The best sensor exhibited two wide linear response ranges (2 μM up to ∼0.5 mM and 0.6 mM up to ∼5.5 mM respectively) with sensitivities of 921 and 265 μA cm⁻² mM⁻¹ respectively and low limit of detection of 100 nM (S/N=3). The sensor was very selective towards glucose in the presence of various interference and showed long term stability. Moreover, the developed thin film modified electrode could generate one electron current in nonenzymatic fuel cell setup at room temperature.     

A Novel Hydrogen Peroxide Amperometric Sensor Based on Hierarchical 3D Porous MnO2−TiO2 Composites

A novel nanocomposite electrode based on hierarchical 3D porous MnO₂?TiO₂ for the application in hydrogen peroxide (H₂O₂) sensors has been explored. This electrode was fabricated by growing TiO₂ cross‐linked nanowires on a commercial fluorine tin oxide (FTO) glass via a hydrothermal process and subsequent deposition of 3D honeycomb‐like MnO₂ nanowalls using an electrodeposition method (denoted as 3D MNS‐TNW@FTO). The obtained 3D MNS‐TNW@FTO electrode was characterized by scanning electron microscopy (SEM), Raman spectroscopy, X‐ray diffraction (XRD), and X‐ray photoelectron spectroscopy (XPS). Based on such a unique 3D porous framework and the existence of MnO₂, the electrode demonstrates a good performance in the detection of H₂O₂, with two linear ranges from 9.8 to 125 μM and 125 μM–1.0 mM, a good selectivity of 8.02 μA mM^?1 cm^?2, and a low detection limit of 4.5 μM. In addition, the simplicity of the developed low‐cost fabrication process provides an efficient method for the mass production of electrocatalytical MnO₂?TiO₂ nanocomposites on commercial FTO glass for H₂O₂ sensing applications and can be adapted for other electrochemical sensors for various biochemical targets. It thus is beneficial for the practical usage in bioanalysis.     

119mSn-Mössbauer-spektren von funktionell substituierten stannylenen und ihren stannio-komplexen mit chrom,molybdän- und wolfram-carbonyl-acceptoren

^119mSn Mössbauer data for a series of base-stabilized, intermolecularly associated tin(II) compounds ith O, Cl, P and As atoms bonded to tin are compared with isomer shifts (IS) and quadrupole splittings (QS) of their stannio complex derivatives with Cr, Mo and W carbonyls. Coordination at the tin lone-pair atom decreases IS to ca. 2.1 ± 0.2 mm s^?1 and increases the QS. QS values reflect the highly associated nature of the complexes (CO)₅MSn(Cl)E(t-Bu)₂ (M Cr, W; E  P, As) which are bridged through μ-E(t-Bu)₂ groups.     

Detection of Dexamethasone Sodium Phosphate in Blood Plasma: Application of Hematite in Electrochemical Sensors

We studied sensor application of a graphene oxide and hematite (α‐Fe₂O₃/GO) composite electrode well‐characterized by the SEM and XRD. Through differential pulse voltammetry (DPV), oxidation of dexamethasone sodium phosphate (DSP) was studied at the surface of a glassy carbon electrode (GCE) modified with graphene oxide nanosheets (GO) and the α‐Fe₂O₃/GO composite. The values of the transfer coefficient (α) and the diffusion coefficient (D) of DSP were 0.5961 and 4.71×10^?5 cm² s^?1 respectively. In the linear range of 0.1–50 μM, the detection limit (DL) was 0.076 μM. In the second step, a GCE was modified with α‐Fe₂O₃/GO composite and the DSP measurement step was repeated to analyzed and compare the effects of hematite nanoparticles present on graphene oxide surfaces. According to the results, α and D were 0.52 and 2.406×10^?4 cm² s^?1 respectively and the DL was 0.046 μM in the linear range of 0.1–10.0 μM. The sensor is simple, inexpensive and uses blood serum.     

A Glucose Biosensor Based on Immobilization of Glucose Oxidase into 3D Macroporous TiO2

3D macroporous TiO₂ inverse opals have been derived from a sol‐gel procedure using polystyrene colloidal crystals as templates. EDS and SEM showed a face‐centered cubic (FCC) structure TiO₂ inverse opal was obtained. Glucose oxidase (GOx) was successfully immobilized on the surface of indium‐tin oxide (ITO) electrode modified by TiO₂ inverse opal (TiO_2(IO)). Electrochemical properties of GOx/TiO_2(IO)/ITO electrode were characterized by using the three electrodes system. The result of cyclic voltammetry showed that a couple of stable and well‐defined redox peaks for the direct electron transfer of GOx in absence of glucose, and the redox peak height enhanced in presence of 0.1 μM glucose. Compare with the ordinary structured GOx/TiO₂/ITO electrode, inverse opal structured GOx/TiO_2(IO)/ITO electrode has a better respond to the glucose concentration change. Under optimized experimental conditions of solution pH 6.8 and detection potential at 0.30 V versus saturated calomel electrode (SCE), amperometric measurements were performed. The sensitivity and the detection limit of glucose detection was 151 μA cm^?2 mM^?1 and 0.02 μM at a signal‐to‐noise ratio of 3, respectively. The good response was due to the good biocompatibility of TiO₂ and the large effective surface of the three‐dimensionally ordered macroporous structure.     

Alloying during codeposition of copper and tin out of silicofluoride electrolytes

A technique for obtaining binary Cu-Sn alloys containing 20–35 mol % Sn is proposed. The technique—the electrochemical deposition out of silicofluoride electrolytes—ensures a high deposition rate of coatings (25–50 μm h^?1). The formation of intermetallic compound Cu₁₀Sn₃ is found to occur at a high current density, in conditions of the tin reduction depolarization and the copper reduction superpolarization. The alloys consist of submicron grains. Apart from crystalline Cu₁₀Sn₃, they include x-ray-amorphous tin (2–12 mol %) and tin oxides (≤1–3 mol %). The alloys feature high hardness (4200 MPa), corrosion resistance, and solderability.     

Anodic Stripping Voltammetric Detection of Arsenic(III) at Gold Nanoparticle‐Modified Glassy Carbon Electrodes Prepared by Electrodeposition in the Presence of Various Additives

The simple, fast and highly sensitive anodic stripping voltammetric detection of As(III) at a gold (Au) nanoparticle‐modified glassy carbon (GC) (nano‐Au/GC) electrode in HCl solution was extensively studied. The Au nanoparticles were electrodeposited onto GC electrode using chronocoulometric technique via a potential step from 1.1 to 0 V vs. Ag|AgCl|NaCl (sat.) in 0.5 M H₂SO₄ containing Na[AuCl₄] in the presence of KI, KBr, Na₂S and cysteine additives. Surfaces of the resulting nano‐Au/GC electrodes were characterized with cyclic voltammetry. The performances of the nano‐Au/GC electrodes, which were prepared using different concentrations of Na[AuCl₄] (0.05–0.5 mM) and KI additive (0.01–1.0 mM) at various deposition times (10–30 s), for the voltammetric detection of As(III) were examined. After the optimization, a high sensitivity of 0.32 mA cm^?2 μM^?1 and detection limit of 0.024 μM (1.8 ppb) were obtained using linear sweep voltammetry.     

Nickel Hydroxide and Intercalated Graphene with Ionic Liquid Nanocomposite‐modified Electrode for Sensing of Glucose

A novel non‐enzymatic glucose sensor based on nickel hydroxide and intercalated graphene with ionic liquid (G‐IL) nanocomposite modified glass carbon electrode was fabricated. Scanning electron microscope, Fourier transform infrared spectra and energy dispersive X‐ray spectroscopy of the nanocomposite confirmed the morphology and ingredient of Ni(OH)₂ as well as G‐IL. Moreover, experimental results of cyclic voltammetry, electrochemical impedance spectroscopy and chronoamperometry indicated the sensing properties of Ni(OH)₂ at Ni(OH)₂/G‐IL modified electrode towards the typical electrocatalytic oxidation process of glucose at 0.43 V in 0.10 M NaOH. The current response was linearly related to glucose concentration in a range from 0.5 to 500 μM with a detection limit of 0.2 μM (S/N = 3) and sensitivity of 647.8 μA mM^?1 cm^?2. The response time of the sensor to glucose was less than 2 s. This work may be expected to develop an excellent electrochemical sensing platform of G‐IL as a catalysis carrier.     

Determination of Trace Tin by Anodic Stripping Voltammetry at a Carbon Paste Electrode

A sensitive and selective procedure for the determination of trace tin at a carbon paste electrode was described. Each measurement cycle consisted of three steps: accumulation, reduction and stripping. The tin complex with bromopyrogallol red (BPR) was accumulated on the electrode surface in 0.10 mol/L acetate buffer (pH 4.5). After electrochemical reduction of Sn(II) had been carried out, the reoxidation wave of Sn(0) appeared at ?0.69 V (vs. SCE) on scanning the potential in the positive direction in 4.0 mol/L HCl. For a preconcentration time of 2 min, the detection limit was 0.06 μg/L (5×10^?10 mol/L ) and the linear range was from 0.1 to 50 μg/L. The proposed method was applied to the determination of tin in canned food and waste water samples with satisfactory results.     

Determination of fluoride and tin in fluoride-doped tin oxide films on glass

Time-consuming fusion and pyrohydrolysis methods for quantifying fluoride and tin in fluoride-doped tin oxide films on glass are replaced by a simple electrolytic reduction for sample preparation. The unusual conductivity of these films enables solutions to be produced in which fluoride can be quantified by ion chromatography. Tin is quantified in the original sample by x-ray fluorescence spectrometry. Electrolytic reduction and the fusion/pyrohydrolysis methods are compared for films with Sn/F ratios of 10–40 (71–183 μg cm^?2 tin and 0.54–2.8 μ cm^?2 fluoride). The Sn/F ratios and precision are similar for the two methods. The older method only yields the tin/fluoride ratio; the electrolytic method gives results as mass per unit area and requires much less time per sample.     

Codeposition of copper and tin from acidic sulfate solutions containing polyethylene glycols. Effect of length of the hydrocarbon chain

Voltammetry and electrochemical impedance spectroscopy technique were applied to study the effect of polyethylene glycols (PEG) with different molecular mass on Cu(II) and Sn(II) reduction kinetics in acidic sulfate solutions. Tetraethylene glycol was found to be the surface-active oligomer on both Cu and Sn substrates that holds the shortest (–CH₂–CH₂–O–)_m chain. The exchange current density of the rate-limiting step Cu²⁺ + e → Cu⁺ falls drastically with an increase in the molecular mass of PEG. An addition of PEG into halide-free Sn(II) solutions results in the significant inhibition of Sn(II) reduction in the entire range of cathodic polarizations including the region of limiting current. Inhibition degree also increases with PEG molecular mass. In contrast with Cu|Cu(II) system, formation of adsorption layers on Sn electrodes proceeds significantly slower. Underpotential deposition of Sn(II) is observed in the region of Cu(II)-limiting current. The characteristic current minimum arises in the region where free Sn phase is thermodynamically stable. It deepens with the length of the hydrocarbon chain of PEG. The fall of current density seems to arise from the inhibitive PEG adsorption on tin atoms that are still not incorporated into general Cu–Sn lattice.     

Gold Surface Functionalization with S‐containing Organic Compounds and Gold Nanoparticles for Ethylene Glycol Electrooxidation

In this work a gold electrode modified with self‐assembled layers (SAMs) composed with organic S‐containing compound and gold nanoparticles was prepared. The electrode with SAMs endowed with gold nanoparticles gave the high catalytic effect for ethylene glycol (EG) electrooxidation in solution at pH 7. For this novel sensor a linear relationship between the current response of EG at the potential of peak maximum (j_p) and the concentration of this compound in solution (c_EG) was found over the range 0.1 µM to 0.7 M with the detection sensitivity j_p/c_EG equal to about 5 A cm^?2 mol^?1 dm³ (at v=0.1 V s^?1) and the detection limit of 0.046 µM.