Novel photo-crosslinkable liquid crystalline polymers containing vanillylidene cycloalkanones and azobenzene units

Two series of novel liquid crystalline photo-crosslinkable bis(vanillylidene-azobenzene) cycloalkanone containing polymers, namely poly(vanillylidene alkyloxy-4,4'-azobenzenedicarboxylic ester)s, have been synthesised from bis[m-hydroxyalkyloxy(vanillylidene)cycloalkanone] (m = 6, 8, 10) with azobenzene dicarbonylchloride by solution polycondensation method at ambient temperature. Polymers with varying spacer lengths have been synthesised and characterised by spectroscopic techniques. These variations have been correlated with the thermal properties and transition temperatures. Thermal transitions were analysed by differential scanning calorimetry (DSC) and the mesophases were identified by hot stage optical polarised microscopy (HOPM). All of the polymers were found to exhibit liquid crystalline properties. Transition temperatures were observed to decrease with increasing spacer length. The thermogravimetric analysis reveals that all of the polymers were stable up to 280°C undergo two-stage decomposition. Using the UV-visible photolysis studies we investigated the simultaneous behaviour of reactivity rates of crosslinking in the vanillylidene unit and isomerisation caused by the azobenzene unit in the photo-crosslinkable main chain liquid crystalline polymers. The photolysis of liquid crystalline bis(vanillylidene)cycloalkanone-based polymers reveals that there are two kinds of photoreactions in these systems: the EZ photoisomerisation of azobenzene unit and 2p+2p addition by vanillylidene units. The EZ photoisomerisation in the liquid crystal phase disrupts the parallel stacking of the mesogens, resulting in the transition from the liquid crystal phase to isotropic phase. The photoreaction involving 2p+2p addition of the bis(vanillylidene)cycloalkanone units in the polymers results in the conjoining of the chains. The cyclopentanone polymers exhibited a faster rate of photolysis than the cyclohexanone polymers.     

Thermal conductivity and thermal expansivity of thermotropic liquid crystalline polymers

The thermal conductivity and thermal expansivity of a thermotropic liquid crystalline copolyesteramide with draw ratio λ from 1.3 to 15 have been measured parallel and perpendicular to the draw direction from 120 to 430 K. The sharp rise in the axial thermal conductivity K_par; and the drastic drop in the axial expansivity α_∥ at low λ, and the saturation of these two quantities at λ > 4 arise from the corresponding increase in the degree of chain orientation revealed by wide-angle x-ray diffraction. In the transverse direction, the thermal conductivity and expansivity exhibit the opposite trends but the changes are relatively small. The draw ratio dependences of the thermal conductivity and expansivity agree reasonably with the predictions of the aggregate model. At high orientation, K_par; of the copolyesteramide is slightly higher than that of polypropylene but one order of magnitude lower than that of polyethylene. In common with other highly oriented polymers such as the lyotropic liquid crystalline polymer, Kevlar 49, and flexible chain polymer, polyethylene, α_par; of the copolyesteramide is negative, with a room temperature value differing from those of Kevlar 49 and polyethylene by less than 50%. Both the axial and transverse expansivity show transitions at about 390 and 270 K, which are associated with large-scale segmental motions of the chains and local motions of the naphthalene units, respectively. ©1995 John Wiley & Sons, Inc.     

Luminescent Iridium-containing liquid crystalline polymers in the side chain

Luminescent liquid crystalline polymers consisting of Iridium attached to polysiloxanes are prepared. 4-Cyanophenyl 4-(allyloxy) benzoate (M₁) and an Iridium complex (Ir-M₂) grafted to poly(methylhydrogeno)siloxane are used for the preparation of the Iridium-containing liquid crystalline polymers. The chemical structures are characterised by Fourier transform infrared spectroscopy and ¹H NMR. The mesomorphic properties and phase behaviour are investigated by differential scanning calorimetry, thermogravimetric analysis, polarising optical microscopy and X-ray diffraction. The polymers containing <1.2 mol% of the Iridium ions reveal reversible mesomorphic phase transition, wide mesophase temperature ranges and high thermal stability. The introduction of the Iridium ions does not change the liquid crystalline state of polymer systems; on the contrary, the polymers are enabled with the luminescent properties. With the Iridium ion contents ranging between 0.3 and 1.2 mol%, luminescent intensity of polymers gradually increased. The temperature dependence of luminescent intensity was studied in the liquid crystalline phase.     

Progress in liquid chromatography of synthetic electroneutral polymers

Recent achievements and anticipated future progress in high performance liquid chromatography of synthetic electroneutral polymers (polymer HPLC) are briefly reviewed. Basic retention mechanisms of polymer HPLC are explained and corresponding separation procedures are discussed. Advantages, drawbacks and pitfalls are presented of the most important polymer HPLC method, namely size exclusion chromatography. Principles of polymer HPLC methods combining various separation mechanisms within one chromatographic column (coupled procedures) or in a set of different chromatographic columns (two- and multi-dimensional procedures) are outlined.     

SAXS investigations on chiral liquid crystalline polymers: antiferroelectric and ferrielectric structures?

The structure and phase behavior of liquid crystalline polymers (LCPs) having a common chiral side chain mesogen but different main chain structures have been investigated using small-angle X-ray scattering (SAXS). While the low molecular weight chiral side chain mesogen by itself exhibits ferroelectricity, the SAXS data of the side chain LCP with a flexible polyacrylate backbone contains a bilayered superstructure peak that is indicative of antiferroelectric order. The combined LCP with a nonpolar main chain mesogen also has a bilayered superstructure, but has a different structural organization in the proposed antiferroelectric phase compared to the side chain LCP. Further changes in the phase behavior and structural organization occur when a polar group is introduced into the main chain mesogen. A ferrielectric phase has been proposed to explain the observation of a trilayered superstructure in the corresponding SAXS data. The influence of the chemical structure and connectivity on the phase behavior and superstructure formation in the chiral LCPs is discussed.     

Liquid‐crystalline azobenzene‐containing ferrocene‐based polymers: study on synthesis and properties of main‐chain ferrocene‐based polyesters with azobenzene in the side chain

Ferrocene‐based polymers are characterized by their electrochemical activity, good redox properties, thermal, photochemical stability, and liquid crystallinity, and thus they have various applications in different fields. A comprehensive investigation on the synthesis and properties of three novel main‐chain ferrocene‐based polyesters with azobenzene in the side chain (MFPAS) was carried out. The main‐chain ferrocene‐based polyester, poly(N‐phenyldiethanolamine 1,1′‐ferrocene dicarboxylate (PPFD), was synthesized via the solution polycondensation reaction of 1,1′‐ferrocenedicarbonyl chloride with phenyldiethanolamine (PDE). The novel MFPAS were synthesized via the post‐polymerization azo‐coupling reaction of PPFD with three different 4‐substituted anilines including 4‐nitroaniline, 4‐aminobenzoic acid, and 4‐aminobenzonitrile to produce 4‐nitrophenylazo‐functionalized‐PPFD (PPFD‐NT), 4‐carboxyphenylazo‐functionalized‐PPFD (PPFD‐CA), and 4‐cyanophenylazo‐functionalized‐PPFD (PPFD‐CN), respectively. All the synthesized polymers were characterized by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, and UV–visible spectroscopy. In addition, powder X‐ray diffraction patterns were measured for the synthesized polymers. The photoisomerization of the MFPAS was studied. The thermal properties of the MFPAS were studied using thermogravimetric analysis and differential scanning calorimetry. PPFD‐CA and PPFD‐CN were found to be more thermally stable than PPFD‐NT. Finally, the liquid‐crystalline properties of PPFD and the MFPAS were examined using polarized optical microscope. It was found that all the polymers possessed nematic phases and exhibited textures with schlieren disclinations. Copyright © 2012 John Wiley & Sons, Ltd.     

Substituent effect on azobenzene‐based liquid‐crystalline organophosphorus polymers

An Erratum has been published for this article in Journal of Polymer Science Part A: Polymer Chemistry (2003) 41(23) 3862 A new series of combined‐type, azobenzene‐based organophosphorus liquid‐crystalline polymers were synthesized, and their photoisomerization properties were studied. The prepared polymers contained azobenzene units as both the main‐chain and side‐chain mesogens. Various groups were substituted in the terminal of the side‐chain azobenzene mesogen, and the effects of the substituents were investigated. All the polymers were prepared at the ambient temperature by solution polycondensation with various 4‐substituted phenylazo‐4′‐phenyloxyhexylphosphorodichloridates and 4,4′‐bis(6‐hydroxyhexyloxy) azobenzene. The polymers were characterized with gel permeation chromatography, Fourier transform infrared, and ¹H, ¹³C, and ³¹P NMR spectroscopy. Thermogravimetric analysis revealed that all the polymers had high char yields. The liquid‐crystalline behavior of the polymers was examined with hot‐stage optical polarizing microscopy, and all the polymers showed liquid‐crystalline properties. The formation of a mesophase was confirmed by differential scanning calorimetry (DSC). The DSC data suggested that mesophase stability was better for electron‐withdrawing substituents than for halogens and unsubstituted ones. Ultraviolet irradiation studies indicated that the time taken for the completion of photoisomerization depended on the dipolar moment, size, and donor–acceptor characteristics of the terminal substituents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3188–3196, 2003     

Molecular modeling and thermoanalytical studies of thermophysical properties of some polymers

The results of computational modeling and experimental data on some thermophysical properties of selected polymers were compared. Different engineering polymers, e.g. polycarbonates and terephthalate polyesters, were considered and their glass transition temperatures and thermal stabilities were determined, by using thermoanalytical methods, e.g. DSC and TG. Measurements were carried out with Perkin-Elmer DSC 7 and TGA 7 instruments. Molecular modeling and computer calculations were performed at the Interdisciplinary Computer Modeling Center (ICM) of Warsaw University, using a Cray El 98 computer and the Insight II software of BIOSYM Technologies Inc. Reasonably good agreement was found between the experimental and calculated values of the glass transition temperatures of the investigated polymers, e.g. for poly(butylene terephthalate)T _g (calc.)=74C andT _g (experim.)=70C. Discrepancies were observed for the temperature of half decompositionT _d,1/2, some of them can be explained by effects of polymer molecular weight and/or char-forming effects.Polymer modeling computations were performed at the Interdisciplinary Computer Modeling Center (ICM) of the Warsaw University, where a CRAY EL 98 computer and the software of BIOSYM Technologies, Inc. were used.     

Synthesis,spectral and thermal studies on pyrazolatebridged palladium(II) coordination polymers

Synthesis, spectroscopic characterization and thermal behavior of pyrazolate-bridged palladium complexes [Pd(μ-Pz)₂]_n (1), [Pd(μ-mPz)₂]_n (2), [Pd(μ-dmPz)₂]_n (3), [Pd(μ-IPz)₂]_n (4) {pyrazolate (Pz^–), 4-methylpyrazolate (mPz^–), 3,5-dimethylpyrazolate (dmPz^–), 4-iodopyrazolate (IPz^–)} have been described in this work. The exobidentate coordination mode of pyrazolato ligands in 1–4 was inferred on basis of IR spectroscopic evidences. TG investigations indicated that the introduction of substituents at the 4 position in the pyrazolyl moiety into coordination polymers do not affect significantly their thermal stability, whereas at the 3 and 5 position reduced the stability of the main chain. Metal palladium was the final product of the thermal decompositions, which was identified by X-ray powder diffraction.     

Influence of alkoxy tail length and unbalanced mesogenic core on phase behavior of mesogen‐jacketed liquid crystalline polymers

When the flexible terminal substituent changes from butoxy to hexyloxy or longer, smectic C (S_C) liquid crystalline phase was firstly reported to develop from a kind of mesogen‐jacketed liquid crystalline polymer (MJLCP) whose mesogenic side groups are unbalancedly bonded to the main chain without spacers. A series of MJLCPs, poly[4,4′‐bis(4‐alkoxyphenyl)‐2‐vinylbiphenyl(carboxide)] (nC2Vp, n is the number of the carbons in the alkoxy groups, n = 2, 4, 6, 8, 10, and 12) were designed and synthesized successfully via free radical polymerization. The molecular weights of the polymers were characterized with gel permeation chromatography, and the liquid crystalline properties were investigated by differential scanning calorimetry, polarized light microscopy experiments, and 1D, 2D wide‐angle X‐ray diffraction. Comparing with the butoxy analog, the polymer with unbalanced mesogenic core and shorter flexible substituents (n = 2, 4) keeps the same smectic A (S_A) phase, but other polymers with longer terminal flexible substituents (n = 6, 8, 10, and 12) can develop into a well‐defined S_C phase instead of S_A phase. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 505–514, 2009     

Effect of stoichiometry on liquid crystalline supramolecular polymers formed with complementary nucleobase pair interactions

We report herein studies on the liquid crystalline behavior of a series of supramolecular materials that contain different ratios of two complementary symmetrically-substituted alkoxy-bis(phenylethynyl)benzene AA- and BB-type monomers. One monomer has thymine units placed at either end of the rigid mesogenic core, while the other has N⁶-(4-methoxybenzoyl)-adenine units placed on the ends. Differential scanning calorimetric and polarized optical microscopy studies have been carried out on these systems. These studies show that the material's behavior is strongly dependent on its thermal history. As a result, the materials can exhibit, on heating, either a liquid crystalline phase, a crystalline phase, or the coexistence of crystalline and liquid crystalline regions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5049–5059, 2006     

Thermoanalytical studies on complexes of clotrimazole with cyclodextrins

γ-Cyclodextrin and dimethyl-β-cyclodextrin were used as solubilizing agents for a very poorly water-soluble drug, an imidazole derivative antifungal agent, clotrimazole; with the aim of improving the physicochemical properties of the drug. Solid products were prepared by physical mixing, kneading, precipitation and spray-drying methods in 1:1 and 1:2 drug:cyclodextrin molar ratios. Drug interactions were studied by thermoanalytical methods such as DSC, DTA, TG and DTG, X-ray diffractometry and Fourier transformation-infrared spectroscopy. The results demonstrated the formation of inclusion complexes in some products. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermoanalytical studies on complexes of ketoconazole with cyclodextrin derivatives

Inclusion complexation between cyclodextrin derivatives (hydroxypropyl-β-cyclodextrin and methyl-β-cyclodextrin) and a very poorly water-soluble antifungal agent, ketoconazole, was studied. Solid products were prepared by physical mixing, kneading and spray-drying methods in four molecular ratios: 2:1, 1:1, 1:2 and 1:3. The possibility of complex formation between the drug and the cyclodextrins was studied by thermal analysis. Supplementary techniques, such as X-ray diffractometry and Fourier transformation-infrared spectroscopy, were also applied to interpret the results of the thermal study of the products. This revised version was published online in July 2006 with corrections to the Cover Date.     

Liquid‐crystalline thermosets by the curing of dimeric liquid‐crystalline epoxyimine monomers with 2,4‐toluene diisocyanate

We studied the curing processes of several series of dimeric liquid‐crystalline epoxyimine monomers with 2,4‐toluene diisocyanate (TDI) alone or with added catalytic proportions of 4‐(N,N‐dimethylamino)pyridine. We obtained isotropic materials or liquid‐crystalline thermosets with different degrees of order, which depended on the structures of the monomers. To fix ordered networks, we had to do the curing in two steps when TDI was used alone as the curing agent. However, when a tertiary amine was added in catalytic proportions, the ordered networks were fixed in just one step. In this way, we were able to fix both nematic and smectic mesophases. The significance of the polarization of the mesogen for obtaining liquid‐crystalline thermosets was demonstrated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2521–2530, 2003     

Phase behaviour of lyotropic liquid crystalline side chain polymers in aqueous solutions

Amphiphilic lyotropic liquid crystalline surfactants are synthesized displaying 10-undecenoic acid as hydrophobic and ethyleneglycol units as hydrophilic parts of the molecules. By addition reaction of the monomeric surfactants with poly [oxy(methylsilylene)], the surfactants are attached as side chains to the siloxane main chain. The phase behaviour of a polymer-water system and the corresponding monomer-water system is investigated by polarizing microscopy. The monomeric surfactant exhibits a liquid crystallineM ₁-phase of hexagonally packed, rod-like micelles in a concentration range of 49 to 70% surfactant. The liquid crystalline state of the polymeric surfactant is more stable, which is indicated by a broader temperature- and concentration range (35%–90% polymer surfactant). At lower concentration aM ₁-phase exists, which is separated by a cubic phase from a lamellarG-phase at higher concentration of the polymer surfactant. Compared to the monomeric system, the increased stability of the polymeric mesophase can be understood by the restriction of motions of the amphiphiles due to the linkage to the polymer main chain.Dedicated to Prof. Dr. F. H. Müller.The authors are greatly indebted to Wacker Chemie, D-Burghausen, FRG for kindly delivering the poly(hydrogensiloxane).     

Processing studies and thermal stability of addition polymers from 1,4,5,8-tetrahydro-1,4;5,8-diepoxyanthracene and Bis-dienes

1,4,5,8-Tetrahydro-1,4;5,8-diepoxyanthracene reacts with various anthracene end-capped polymide oligomers to form Diels-Alder cycloaddition copolymers. The polymers are soluble in common organic solvents, and dehydrate thermally at temperatures of 300–350°C to give thermal oxidatively stable pentiptycene units along the polymer backbone. Because of their high softening points and good thermal oxidative stability, the polymers are candidates for matrix resins for high temperature composite applications. To assess their usefulness for such applications, several parameters have been studied affecting the properties of the final polymer. These parameters include varying the formulated molecular weight of the end-capped prepolymers, and use of meta-substituted aromatic diamine in place of some of the para-substituted diamine. Processability of the resins was studied using rheometric spectrometry, and a processing scheme was devised. Finally, several formulations of neat resins were compression molded into coupons, and evaluated for longterm stability in air at 315 and 371°C. The best combination of good processability and thermal oxidative stability was obtained from polymers synthesized with small amounts of meta-diamine substitution and higher formulated molecular weight prepolymers.     

Influence of alkyl tail length on self-organisation of side-chain liquid crystalline polymers with biphenyl hemiphasmidic mesogens

A new and simple series of side-chain liquid crystalline polymethacrylates containing biphenyl hemiphasmidic mesogens based on 4-[(3,4,5-trialkan)-1-carbonylbenzoate]biphenyl (denoted as PT_mBMA, m = 6, 8, 10, 12, 14, 16, 18, m refers to the carbon number of alkoxy tails) groups was designed and successfully synthesised via free radical polymerisation. The phase structures and transitions of the polymers were investigated by the combination of techniques including differential scanning calorimetry, polarizing microscope, one-dimensional/two-dimensional wide-angle X-ray diffraction, and small-angle X-ray scattering. The experimental results revealed that the liquid crystalline phase structures and behaviours of the polymers were found to be strongly dependent on the alkyl tail length (m). When m = 6, the PT_mBMA formed a stable smectic phase above T_g. When m = 8, 10, 12, 14, 16, 18, the sample presented a hexagonal columnar mesophase (Φ_h), suggesting that the alkyl length has played an important role in the phase behaviours of hemiphasmidic side-chain liquid crystalline polymers.     

Main‐chain viologen polymers with triflimide counterion exhibiting lyotropic liquid‐crystalline properties in polar organic solvents

The solution‐phase behavior of three main‐chain viologen polymers, which are composed of isomeric xylyl units and triflimide as a counterion, was studied in methanol, dimethylformamide, acetonitrile, and dimethyl sulfoxide as solvents microscopically under crossed polarizers. Each of them exhibited a lyotropic lamellar phase in both polar protic and aprotic solvents. Their C^* for the formation of biphasic solutions (1–5 wt %) and concentrations (20–30 wt %) for the lyotropic solutions in methanol was much lower than those in polar aprotic solvents (20–71 and 60–81 wt %, respectively). Their high solubility, high C^* for the formation of biphasic solutions, and high concentrations for the formation of lyotropic solutions in polar aprotic solvents were related to the significant reduction of strong ionic interactions between triflimide and 4,4′‐bipyridinium ions in each of these viologen polymers. They were the first examples of viologen polymers that exhibited a lyotropic phase in polar aprotic solvents. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2015–2024, 2002     

Aromatic poly(sulfone sulfide amide imide)s as new types of soluble thermally stable polymers

A new diamine monomer containing flexible sulfone, sulfide, and amide units was prepared via three steps. Nucleophilic chloro displacement reaction of 4‐aminothiophenol with 4‐nitrobenzoyl chloride in the presence of propylene oxide afforded N‐(4‐mercapto‐phenyl)‐4‐nitrobenzamide and subsequent reduction of the nitro intermediate led to 4‐amino‐N‐(4‐mercapto‐phenyl)benzamide. Two moles of this amino thiophenol compound was reacted with bis‐(4‐chloro phenyl)sulfone to provide a novel diamine monomer. The diamine was reacted with aromatic dianhydrides to form polyimides via a two‐step polycondensation method, formation of poly(amic acid)s, followed by chemical imidization. The resulting polymers were characterized and their physical properties including thermal behavior, thermal stability, solubility and inherent viscosity were studied. Copyright © 2007 John Wiley & Sons, Ltd.     

Synthesis by ATRP and effects of molecular weight on photomechanical properties of liquid crystalline polymers containing side-chain azobenzene chromophores

The synthesis of a series of azobenzene containing liquid crystalline methacrylic homopolymers, poly(4-ω-methacryloyloxy-hexyloxy-4′-ethoxyazobenzene) [Poly(M6A)], with distinct average chain lengths and low polydispersity has been achieved by Atom Transfer Radical Polymerization (ATRP) in THF solution using allyl 2-bromoisobutyrate as initiator and Cu(I)Br as catalyst. Under the adopted conditions the living centers concentration is found to be constant throughout the polymerization process and well defined chain end-groups are obtained. All the obtained polymeric samples, having average molecular mass ranging from 3300 to 14000 g/mol, exhibit smectic and nematic liquid-crystalline phases on heating, with transition temperatures strongly dependent on polymerization degree, as characterized by differential scanning calorimetry and polarized optical microscopy.The photomechanical effects (i.e. the dependence of volume and density) exhibited upon trans-to-cis and cis-to-trans photoisomerization of the azobenzene mesogenic groups have been investigated by ellipsometry and related to molecular weight, with particular attention to important parameters for potential applications such as the relative variation of total volume, response time, stability and reproducibility.