Direct determination of free methionine in soy-based infant formula

A method was developed for the direct determination of free methionine in soy-based infant formula, with analyte separation and quantitation by reversed-phase liquid chromatography (LC), and UV absorbance at 214 nm, respectively. Sample preparation required only dilution with mobile phase and syringe filtration. Using a 0.02M KH2PO4 mobile phase (pH adjusted to 2.9 with 85% o-phosphoric acid) and 0.7 mL/min flow rate, methionine eluted at approximately 8 min, and total run time was 14 min after column regeneration with acetonitrile-water. System linearity was demonstrated as peak area versus analyte concentration, ranging from 80 to 120% of the formula specification for free methionine (r > 0.999, and all residuals < 0.45%). Intermediate precision relative standard deviation values were < 1.5% for ready-to-feed and reconstituted powder samples, and recoveries ranged from 98.0 to 103.5% for inter-method comparison with an amino acid analyzer method. The limit of quantitation was 3 mg methionine/L in the "as fed" infant formula. Despite the relatively weak UV absorptivity of methionine, the 214 nm signal was sufficiently intense in the 30-65 mg/L (201-436 microM) range to afford quantitation by peak area proportionation versus a 2-point external standard calibration. This direct UV detection after reversed-phase LC separation provides a simple and accurate method for determining free methionine without derivatization.     

Analysis and occurrence of seven artificial sweeteners in German waste water and surface water and in soil aquifer treatment (SAT)

A method for the simultaneous determination of seven commonly used artificial sweeteners in water is presented. The analytes were extracted by solid phase extraction using Bakerbond SDB 1 cartridges at pH 3 and analyzed by liquid chromatography electrospray ionization tandem mass spectrometry in negative ionization mode. Ionization was enhanced by post-column addition of the alkaline modifier Tris(hydroxymethyl)amino methane. Except for aspartame and neohesperidin dihydrochalcone, recoveries were higher than 75% in potable water with comparable results for surface water. Matrix effects due to reduced extraction yields in undiluted waste water were negligible for aspartame and neotame but considerable for the other compounds. The widespread distribution of acesulfame, saccharin, cyclamate, and sucralose in the aquatic environment could be proven. Concentrations in two influents of German sewage treatment plants (STPs) were up to 190 μg/L for cyclamate, about 40 μg/L for acesulfame and saccharin, and less than 1 μg/L for sucralose. Removal in the STPs was limited for acesulfame and sucralose and >94% for saccharin and cyclamate. The persistence of some artificial sweeteners during soil aquifer treatment was demonstrated and confirmed their environmental relevance. The use of sucralose and acesulfame as tracers for anthropogenic contamination is conceivable. In German surface waters, acesulfame was the predominant artificial sweetener with concentrations exceeding 2 μg/L. Other sweeteners were detected up to several hundred nanograms per liter in the order saccharin ≈ cyclamate > sucralose. Figure Some artificial sweeteners are excreted unchanged and in particular acesulfame is a perfect tracer for municipal waste water Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Development of a quantitative high-performance thin-layer chromatographic method for sucralose in sewage effluent, surface water, and drinking water

Sucralose, a persistent chlorinated substance used as sweetener, can already be found in waste water, and various countries focused on the release of sucralose into the aquatic environment. A quantitative high-performance thin-layer chromatography (HPTLC) method, which is orthogonal to existing methods, was developed to analyze sucralose in water. After sample preparation, separation of up to 17 samples was performed in parallel on a HPTLC plate silica gel 60 F(254) with a mixture of isopropyl acetate, methanol and water (15:3:1, v/v/v) within 15 min. Due to the weak native UV absorption of sucralose (≤200 nm), various post-chromatographic derivatization reactions were compared to selectively detect sucralose in effluent and surface water matrices. Thereby p-aminobenzoic acid reagent was discovered as a new derivatization reagent for sucralose. Compared to the latter and to β-naphthol, derivatization with aniline diphenylamine o-phosphoric acid reagent was slightly preferred and densitometry was performed by absorbance measurement at 400 nm. The limit of quantification (LOQ) of sucralose in drinking and surface water was calculated to be 100 ng/L for a given recovery rate of 80% and the extraction of a 0.5 L water sample. The sucralose content determined in four water samples obtained during an interlaboratory trial in 2008 was in good agreement to the mean laboratory values of that trial. According to the t-test, which compares the results with the target value, the means obtained by HPTLC were not significantly different from the respective means of six laboratories, analyzed by HPLC-MS/MS or HPLC-TOF-MS with the use of mostly isotopically labeled standards. The good accuracy and high sample throughput capacity proved HPTLC as a well suited method regarding quantification of sucralose in various aqueous matrices.     

Development and validation of column high-performance liquid chromatographic and ultraviolet spectrophotometric methods for citalopram in tablets

Column high-performance liquid chromatographic (LC) and UV spectrophotometric methods for the quantitative determination of citalopram, a potent and selective serotonin reuptake inhibitor, in tablets were developed. The parameters linearity, precision, accuracy, specificity, robustness, limit of detection, and limit of quantitation were studied according to International Conference on Harmonization guidelines. Chromatography was carried out by the reversed-phase technique on an ACE C18 column with a mobile phase composed of 0.30% triethylamine solution-acetonitrile (55 + 45, v/v) adjusted to pH 6.6 with 10% ortho-phosphoric acid at a flow rate of 1.0 mL/min and 25 degrees C. The UV spectrophotometric method was performed at 239 nm. The linearity of the LC method was in the range of 10.00-70.00 microg/mL, and 2.50-17.50 microg/mL for the UV spectrophotometric method. The interday and intraday assay precision was < 1.5% (relative standard deviation) for the LC and UV spectrophotometric methods. The recoveries were in the range 100.70-101.35% for the LC method and 98.48-98.65% for the UV spectrophotometric method. Statistical analysis by Student's t-test showed no significant difference between the results obtained by the 2 methods. The proposed methods are highly sensitive, precise, and accurate and can be used for the reliable quantitation of citalopram in tablets.     

A Simple HPLC Method for the Quantitation of Molindone in Human Plasma or Serum

Abstract

A simple HPLC method is described for the quantitation of molindone in human serum or plasma using trazadone as an internal standard and UV detection (247 nm). The method was successfully used to determine the steady state levels of molindone in 15 patients receiving the drug. The HPLC results were confirmed by identifying the HPLC peak using LC thermospray mass spectrometry.     

Voltammetric behavior and analytical applications of lomefloxacin, an antibacterial fluorquinolone.

Lomefloxacin was reduced on a dropping mercury electrode, producing one or more peaks, depending on the pH of the aqueous medium. Coulometric measurements gave an experimental value of 1 electron for the main peak. Electrolysis was followed by UV spectrophotometry and liquid chromatography (LC), showing that a new band at 413 nm appeared for the electrolysis product in an acidic medium. Furthermore, by using UV spectrophotometry, an apparent pKa value of 6.75 +/- 0.05 was obtained for lomefloxacin corresponding to the carboxyl moiety in the 3-position. For analytical studies, the differential pulse polarographic mode in 0.1 N HCl was selected. The repeatability and reproducibility of the method were adequate (coefficient of variation [CV], 0.51%). The calibration curve method was used for the lomefloxacin concentration range of 7.0 x 10(-6) to 7.0 x 10(-5)M. The detection and quantitation limits were 1.0 x 10(-6) and 6.9 x 10(-6)M, respectively. For purposes of comparison, both UV spectrophotometric and LC (with UV and fluorimetric detection) methods were developed. The polarographic method showed good selectivity with respect to both excipients and degradation products. The recovery study showed a CV of <2% and an average recovery of 99.5% and it was not necessary to treat the sample before analysis. The method was applied to the determination of the uniformity content of lomefloxacin commercial tablets. The polarographic method was also successfully applied to the quantitation of lomefloxacin in urine, and the renal excretion profile was also determined.     

Determination of phenolic disinfectant agents in commercial formulations by liquid chromatography.

Using liquid chromatography (LC), a convenient and versatile method was developed for the assay of disinfectant products containing the commonly used phenolic agents, alone or in combination, including phenol, 2-phenylphenol, 4-t-amylphenol, 4-chloro-3,5-dimethylphenol (PCMX), 2-benzyl-4-chlorophenol, and triclosan. The procedure involves a simple dilution or dissolution of the product aliquot or portion followed by membrane filtration and LC. The method was applied to 19 different products representing 17 manufacturers and containing from one to 4 phenolic agents. Chromatography was performed using a Zorbax SB-C18 column, acetonitrile-0.05M KH2PO4 (55 + 45, v/v) pH 3.00, as mobile phase and UV detection at 280 nm. The intralaboratory precision of the product assays ranged form 0.34-5.35% (n = 5) and recoveries via fortification varied from 96.1-103.8%. The limits of quantitation (LOQ) and detection (LOD) ranged from 5.58 x 10(-5) to 2.50 x 10(-4) mg/mL and from 1.76 x 10(-5) to 0.67 x 10(-4) mg/mL, respectively, for the 6 analytes. The response for all analytes was observed to be linear for at least a 50-fold range in concentration (0.001-0.05 mg/mL). The proposed method provides an efficient means for the isolation and quantitation of these phenolic compounds.     

A method for the analysis of sucralose with electrospray LC/MS in recipient waters and in sewage effluent subjected to tertiary treatment technologies

A method for the analysis of the artificial sweetener sucralose in sewage water and recipient water was developed. Extraction and clean up was performed with solid-phase extraction utilising Oasis HLB columns. Detection was made by liquid chromatography electrospray mass spectrometry (LC/MS). The triple-quadrupole mass spectrometer was operated in multiple reaction monitoring (MRM) mode. However, ‘pseudo MRM’ was used, a technique where the two quadrupoles monitor the same m/z. The sodium adduct of sucralose was used for quantification, since lower detection limits were obtained as compared to the sucralose quasi-molecular ion in negative ion mode. The two ions with highest intensity in the chlorine isotope pattern were monitored. The reduction of matrix effects with this approach is discussed. The method limit of quantification (MLOQ) for sewage water was 0.2?µg?L^?1, whereas for recipient water MLOQ was 0.02?µg?L^?1. The method was used to analyse effluent samples from an experimental sewage treatment plant (STP) to assess the efficiency of tertiary treatment techniques for removal of sucralose. Filtration through activated carbon was shown to be efficient, while ozonation, advanced oxidation techniques and membrane bioreactors were less efficient. Analyses of receiving waters showed low dilution of sucralose emitted from the STPs.     

Flow-through spectrophotometric sensor for the determination of aspartame in low-calorie and dietary products.

A very simple flow-through sensor is presented for the determination of the intense sweetener aspartame in low-calorie and dietary products. The sensor is implemented in a monochannel flow-injection system with UV spectrophotometric detection using a Sephadex CM-C25 cationic exchanger packed 20 mm high in a flow cell. This method is based on the transient retention of a cationic species of the sweetener on the solid phase when a pH 5.0 acetic acid sodium acetate buffer (0.01 M) is used as a carrier (2.6 mL(-1) min). The carrier itself elutes the analyte from the solid support, regenerating a sensing zone. Aspartame was determined by measuring its intrinsic absorbance at 219 nm at its residence time without any derivatization. Calibration graphs were linear over the range of 5.0 - 600.0 microg mL(-1) with an RSD of 0.55% (peak height). This sweetener was determined in several samples by measuring the height or peak area, obtaining recoveries ranging between 95 - 101% and 97.5 - 101%, respectively. The procedure was validated for its use in the determination of aspartame in low-calorie and dietary products, giving reproducible and accurate results.     

Development and Validation of a Stability-Indicating LC Method for Simultaneous Analysis of Aceclofenac and Paracetamol in Conventional Tablets and in Microsphere Formulations

A stability-indicating reversed-phase LC method for analysis of aceclofenac and paracetamol in tablets and in microsphere formulations has been developed and validated. The mobile phase was 80:20 (v/v) methanol–phosphate buffer (10 mM at pH 2.5 ± 0.02). UV detection was at 276 nm. The method was linear over the concentration ranges 16–24 and 80–120 μg mL^?1 for aceclofenac and paracetamol, respectively, with recovery in the range 100.9–102.22%. The limits of detection and quantitation for ACF were 0.0369 and 0.1120 μg mL^?1, respectively; those for PCM were 0.0631 and 0.1911 μg mL^?1, respectively.     

Simultaneous Determination of Preservatives,Artificial Sweeteners,and Synthetic Dyes in Kimchi by Ultra-Performance Liquid Chromatography Electrospray Ionization Tandem Mass Spectrometry (UPLC-ESI-MS/MS)

Abstract

A simple and rapid method was developed for the simultaneous determination of five preservatives, six artificial sweeteners, and nine synthetic dyes in kimchi using ultra-performance liquid chromatography electrospray ionization tandem mass spectrometry (UPLC-ESI-MS/MS) with multiple reaction monitoring (MRM). The chromatographic separation was performed in 5.5?min using an Acquity UPLC BEH C18 column (100?mm × 2.1?mm, 1.7?µm) with a mobile phase composed of 0.002% trifluoroacetic acid and 10?mM aqueous ammonium acetate or 9:1 (v/v) methanol:acetonitrile. Linear calibration curves were obtained with correlation coefficients above 0.98. The limits of quantification ranged between 0.227 and 8.569?ng/mL, while the recovery values in kimchi samples were from 83.1 to 113.5%. Forty kimchi samples were analyzed for the food additives, with sweeteners detected in more than half of these samples. The most commonly detected sweetener was saccharin, and six of the kimchi samples contained a combination of sweeteners; dulcin, sucralose, acesulfame K, preservatives, and synthetic dyes were not detected. Based on these results, the developed method can be used for the rapid quality control of food additives in kimchi.     

Determination of isoflavones in ready-to-feed soy-based infant formula

An alkaline hydrolysis/liquid chromatography (LC) method was developed for determination of isoflavones in ready-to-feed soy-based infant formula. The method consists of a 15 min methanol extraction, 10 min alkaline hydrolysis, HCl neutralization, gravity filtration, aqueous dilution, and 50 min LC analysis with UV detection at 262 and 250 nm to quantify 6 isoflavone analytes: daidzin, glycitin, genistin, daidzein, glycitein, and genistein. The concentration averages for 10 commercial batches (microg aglycone/g formula) were daidzein, 6.12 +/- 1.23; glycitein, 1.19 +/- 0.16; genistein, 12.8 +/- 2.35; and total, 20.1 +/- 3.61. Validation experiments demonstrated extraction completion and analyte stability to alkaline hydrolysis. Spike recoveries ranged from 97.6 to 104.1%, and a series of accuracy assessments showed that isoflavone concentration determined by the method was within 5% of the true value. The relative standard deviation values for repeatability ranged from 0.4 to 2.2% (n = 10), and from 0.3 to 2.7% (n = 4) for intermediate precision. Isoflavone peak purity was verified by comparing sample and standard peak area ratios (262/250 nm). The limits of detection and quantitation (microg/ formula) ranged from 0.02 to 0.05 and 0.08 to 0.18 microg/g, respectively. The difference between our concentrations and those reported by others in 1995-1998 is attributable to the well-established seasonal variation in soybean isoflavone levels. Although the method was applied exclusively to ready-to-feed formula in the present study, it is equally suitable for powder and concentrated liquid infant formulas.     

Development and validation of a high-throughput based on liquid chromatography with ultraviolet absorption and mass spectrometry detection method for quantitation of cichoric acid in Echinacea purpurea aerial-based dietary supplements

A new, rapid, and reproducible reversed-phased liquid chromatography (LC) method with ultraviolet (UV) absorption and/or mass spectrometry (MS) detection has been developed and validated for quantitation of cichoric acid, a major constituent of Echinacea spp. The method involves the use of a short Phenomenex Hydro-RP C18 column (4 microm, 50 mm x 3.0 mm id) and a simple isocratic mobile phase profile. Both UV (diode array detector) and selective-ion monitoring (SIM) at m/z 472.8 were used for quantitation of cichoric acid. The limit of detection was 0.75 ng for UV and 0.15 ng for MS-SIM, and the limit of quantitation was is 2.5 ng for UV and 0.5 ng for MS-SIM. Water-methanol (1 + 1) soluble extracts of 6 commercially available Echinacea purpurea aerial parts-based dietary supplements (EPADS). EPADS were first profiled using a traditional HPLC-UV method. Their UV chromatograms were compared, and cichoric acid was identified to be a key biomarker for EPADS. Then the samples were analyzed by the fast LC-UV/MS method. The turnaround time for a single analysis was 3 min, compared to 15 to 60 min needed for traditional reported LC methods. The high-throughput method was able to separate the cichoric acid peak from peaks of other components in extracts of complex matrixes of EPADS.     

Validation of a method for determination of phospholipase A2 and melittin in bee venom preparations by capillary electrophoresis

A method was validated for the determination of the 2 main components of bee venom, phospholipase A2 and melittin, by capillary electrophesis (CE). Optimum resolution and selectivity were attained with a running electrolyte of 150 mM phosphoric acid, pH 1.8. The repeatability and day-to-day reproducibility of the migration times were better than 0.36 and 2.8%, respectively. The repeatability and day-to-day reproducibility of the normalized peak areas were better than 1.3 and 2.6%, respectively. The response of the UV detector at 190 nm was linear over < 2 concentration decades, from 0.05 to 1.5 mg/mL, with correlation coefficients of 0.9994 for phospholipase A2 and 0.9997 for melittin. The limits of detection and quantitation were 4.5 and 15 microg/mL, respectively, for phospholipase A2 and 1.6 and 6 microg/mL, respectively, for melittin. The reproducibility of the measurements with 2 different CE instruments was satisfactory; the mean concentration and relative standard deviation (RSD) values for phospholipase A2 and melittin were 14.4% (RSD, 1.3%) and 51.4% (RSD, 1.1%), respectively, with instrument I; the corresponding values with instrument II were 14.5% (RSD, 2.8%) and 52.3% (RSD, 2.2%). The accuracy was estimated by comparison with a liquid chromatographic (LC) method. Differences between the CE and LC measurements were attributed to irreversible adsorption of the analytes on the LC column. The recoveries of phospholipase A2 and melittin with the CE method were 98.8 and 101.7%, respectively.     

Liquid chromatography–fluorescence detection for simultaneous analysis of sulfonamide residues in honey

A rapid, accurate LC analytical method has been developed for determination of eight sulfonamides (sulfacetamide, sulfapyridine, sulfamerazine, sulfamethoxypyridazine, sulfameter, sulfachloropyridazine, sulfamethoxazole and sulfadimethoxine) in honey. The sample was dissolved in phosphoric acid solution (pH 2). After filtration, the sample solution was cleaned by use of two solid-phase extraction (SPE) cartridges-an aromatic sulfonic cation-exchange cartridge and an Oasis HLB cartridge. The eight sulfonamides were then derivatized with fluorescamine and the derivatives were determined by LC with fluorescence detection at excitation and emission wavelengths of 405 and 495 nm, respectively. Average recoveries at three fortification levels in the range 0.02-0.50 mg kg(-1) in twelve different kinds of honey were 73.5-94.1% with coefficients of variation of 4.35-16.60%. The limit of detection (LOD) was 0.002 mg kg(-1) for sulfacetamide, sulfapyridine, sulfamerazine, and sulfamethoxypyridazine; that for sulfameter, sulfachloropyridazine, sulfamethoxazole and sulfadimethoxine was 0.005 mg kg(-1). The limit of quantitation (LOQ) was 0.005 mg kg(-1) for sulfacetamide, sulfapyridine, sulfamerazine, and sulfamethoxypyridazine; that for sulfameter, sulfachloropyridazine, sulfamethoxazole, and sulfadimethoxine was 0.010 mg kg(-1). The method is suitable for determination of multiresidue sulfonamides in the various kinds of honey.     

Selective and stability-indicating methods for the simultaneous determination of mexiletine hydrochloride and/or its related substance: 2,6-dimethylphenol

Four simple, rapid, sensitive, and selective analytical procedures were developed for determination of mexiletine hydrochloride (MX) and/or its related substance: 2,6-dimethylphenol (DMP). The latter is a synthetic impurity for which a maximum pharmacopeial limit is defined. The first method depends on derivative-ratio spectrophotometry, for which the first-derivative signals of the ratio spectra at 259 nm (Deltalambda = 3 nm) are selected for the determination of MX. The second method is based on the spectrofluorometric measurement of MX in alkaline solution in the presence of 15 mM sodium dodecyl sulfate micellar medium at 292 nm (lambdaEx 260 nm). The third method is based on liquid chromatographic (LC) separation of MX and DMP on an RP-C8 column with a mobile phase consisting of 50 mM Na2HPO4-acetonitrile (60 + 40, adjusted to pH 2.4), and quantification of the analytes is achieved with UV detection at 212 nm based on peak area. The fourth method uses the coupling reaction of DMP with 2,6-dibromo-quinone-4-chlorimide (DBQC) in borate buffer to form an intensely colored product that was spectrophotometrically measured using first-derivative amplitudes at 670 nm (Deltalambda = 6 nm) for the determination of DMP. Different variables affecting each method were carefully investigated and optimized. The reliability and analytical performance of the proposed methods, including linearity, range, precision, accuracy, and detection and quantitation limits, were statistically validated. The first 3 methods were successfully applied for the stability-indicating determination of MX in laboratory-prepared mixtures with DMP, as well as for the determination of MX in capsules. Also, the LC and the DBQC spectrophotometric methods permitted the selective determination of DMP in the presence of a large excess of the parent drug at or near the pharmacopeial limit (0.1-1%).     

Evaluation of a Vancomycin-Based LC Column in Enantiomeric Separation of Atenolol: Method Development, Repeatability Study and Enantiomeric Impurity Determination

An LC method was developed and validated for the enantioselective separation and enantiomeric impurity quantitation of atenolol. Separation of the atenolol enantiomers on the Chirobiotic V2 (150 mm × 4.6 mm, 5 μm) column was best achieved using a ternary mobile phase of methanol–acetonitrile-triethylamine acetate 0.5% (w/v), pH 4.5 in a ratio of (45:50:5; v/v/v). Good resolution value of R _s  = 3 was obtained at a flow rate of 1 mL min^?1 within a total run time of less than 40 min. Peak identification was achieved using the standard reference of individual enantiomers. The peak of the impurity was eluted in front of the peak of the main enantiomer. Detection was performed by UV at 226 nm. Within and between day’s repeatabilities for both retention time and peak area were investigated at three concentration levels and found to be low. The method was also found to be efficient for the determination of atenolol enantiomeric impurity. An impurity quantitation level of (R)-atenolol down to 0.08% relative to the main enantiomer (S)-atenolol was found possible.     

Determination of deoxynivalenol in whole wheat flour and wheat bran

A liquid chromatographic (LC) method was developed for determining deoxynivalenol (DON) in whole wheat flour and wheat bran. A 15 g test sample was extracted with acetonitrile-water (84 + 16, v/v) and applied to a Romer MycoSep cleanup column. The eluate was dried and then reconstituted in a 0.1 M phosphate buffer, pH 7.0, and applied to a Vicam DONtest-LC cleanup column. The methanol eluate was chromatographed with a methanol-water (17 + 83, v/v) mobile phase on a C18 column with UV detection at 220 nm. Five replicates at each of 5 fortification levels (0.25, 0.50, 1.0, 2.0, and 4.0 ppm), plus 5 controls, were determined for both whole wheat flour and wheat bran. For flour, the average recoveries were 72.2-91.5% with relative standard deviations (RSDs) of 4.9-18.4%. The intra-assay flour recovery was 82.4% with 9.8% RSD. A 5 replicate sample of naturally incurred wheat had an average of 1.1 ppm DON with 6.7% RSD. For bran, average recoveries of fortified samples were 69.5-99.7% with RSDs of 1.7-18.8%. The intra-assay bran recovery was 81.5% with 8.9% RSD. The limit of detection (about 3x noise) for the method is 0.05 ppm; the correlation coefficient (linearity) was >0.9995. The DON peak was clearly identified and easily integrated in the chromatograms.     

Reversed-Phase Liquid Chromatographic Method for Determination of Daclatasvir Dihydrochloride and Study of Its Degradation Behavior

A simple and selective reversed-phase stability-indicating liquid chromatographic method has been developed and validated for the determination of daclatasvir in drug substance and drug product. Daclatasvir was subjected to acidic, alkaline, oxidative, thermal and photo-degradation study. The LC method was based on isocratic elution of daclatasvir and its degradation products on a reversed-phase C₁₈ Hypersil column using a mobile phase consisting of phosphate buffer (10 mM, 1 mL triethylamine L^?1): acetonitrile (60:40 v/v) at a flow rate of 2 mL min^?1. Quantitation was achieved with UV detection at 312 nm. Linearity, accuracy, and precision were found to be acceptable over the concentration range of 0.75–120 μg mL^?1, with regression coefficient value of 0.9999, and with limit of detection and quantitation of 0.148 and 0.447 μg mL^?1, respectively. Peak purity was checked for principle drug and its alkali induced degradation product, and the pathway of alkaline hydrolysis of daclatasvir was suggested by LC/MS.     

Liquid chromatographic determination of methyl anthranilate in artificially flavored nonalcoholic beverages

A liquid chromatographic method was developed that provides a simple and rapid means of determining methyl anthranilate (MA) in carbonated and noncarbonated, artificial grape-flavored, nonalcoholic beverages. The proposed procedure, which was applied to 12 different products, uses a Nova-Pak C18 column, a mobile phase containing acetonitrile-0.025M KH2PO4 (40 + 60), pH 3.00, and UV detection at 220 nm. Assay values ranged from 0.35 to 16.6 microg MA/mL. The intralaboratory precision (relative standard deviation) for the products ranged from 0.51 to 2.23% (n = 5), and recoveries via fortification ranged from 83.6 to 102.4%. The limits of quantitation and detection were 0.00417 and 0.00125 microg/mL, respectively, and the analyte response was linear over a 100-fold concentration range (0.0001-0.01 mg/mL).