First solvent‐free synthesis of poly(N‐methylolacrylamide) via frontal free‐radical polymerization

We report the first synthesis of poly (N‐methylolacrylamide) (PNMA) via free‐radical frontal polymerization (FP) with solid monomers at ambient pressure. The appropriate amounts of reactants (N‐methylolacrylamide) (NMA) and initiator (ammonium persulfate) were mixed together at ambient temperature without solvent. FP was initiated by heating the wall of the tube with a soldering iron, and the resultant hot fronts were allowed to self‐propagate throughout the reaction vessel. Once initiated, no further energy was required for polymerization to occur. To suppress the fingers of molten monomer, a small amount of nanosilica was added. We also produced PNMA with dimethyl sulfoxide (DMSO) or N‐methyl‐2‐pyrrolidone, as solvent by FP, to study the macrokinetics in FP of PNMA without fillers. The front velocity and front temperature dependence on the ammonium persulfate and N‐methyl‐2‐pyrrolidone concentration were investigated. The polymer was analyzed by thermogravimetric analysis. Results show that without postpolymerization solvent removal, waste production can be reduced. Solvent‐free FP could be exploited as a means for preparation of PNMA with the potential advantage of higher throughput than solvent‐based methods. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4322–4330, 2007     

Facile synthesis of poly(hydroxyethyl acrylate) by frontal free‐radical polymerization

We report the first synthesis of poly(hydroxyethyl acrylate) (PHEA) without solvent by free‐radical frontal polymerization (FP) at ambient pressure. In a typical run, the appropriate amounts of reactant (hydroxyethyl acrylate) and initiator (1,1‐di(tert‐butylperoxy)‐3,3,5‐trimethylcyclohexane) (Luperox 231) were mixed together at ambient pressure. FP was initiated by heating the wall of the tube with a soldering iron, and the resultant hot fronts were allowed to self‐propagate throughout the reaction vessel. Once initiated, no further energy was required for polymerization to occur. To study the macrokinetics, we also produced PHEA frontally with ammonium persulfate as initiator and dimethyl sulfoxide as the solvent. The dependences of the front velocity and front temperature on the initiator concentration and reactant dilution were investigated. The front temperatures were between 124 and 157 °C, depending on the ammonium persulfate concentration. Thermogravimetric analysis indicates that PHEA prepared by FP with ammonium persulfate as initiator had higher thermal stability than solvent‐free frontally prepared PHEA with Luperox 231 as initiator. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 873–881, 2007     

Facile synthesis of amphiphilic gels by frontal free‐radical polymerization

We report a new facile strategy for quickly synthesizing poly(2‐hydroxyethyl acrylate‐co‐vinyl versatate) amphiphilic gels with excellent physicochemical properties by frontal free‐radical polymerization. The appropriate amounts of 2‐hydroxyethyl acrylate, vinyl versatate (VeoVa 9) and ammonium persulfate initiator were mixed together at ambient temperature in the presence of N‐methyl‐2‐pyrrolidone as the solvent medium. Frontal polymerization (FP) was initiated by heating the wall of the tube with a soldering iron. Once initiated, no further energy was required for the polymerization to occur. The dependence of the front velocity and front temperature on the initiator concentration was investigated. The front temperatures were between 132 and 157 °C, depending on the initiator concentration. The morphology, swelling rate, and swelling behavior of amphiphilic gels prepared via FP were comparatively investigated on the basis of scanning electron microscopy, water contact angle, and swelling measurements. Results show that the amphiphilic gels prepared via FP behave with good swelling capacity both in water and organic solvents. The FP can be exploited as an alternative means for synthesis of amphiphilic gels with additional advantages of fast and efficient way. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 823–831, 2010     

Facile synthesis of N‐vinylimidazole‐based hydrogels via frontal polymerization and investigation of their performance on adsorption of copper ions

We report a new facile strategy for quickly synthesizing pH sensitive poly(VI‐co‐HEA) hydrogels (VI = N‐vinylimidazole; HEA = 2‐hydroxyethyl acrylate) by frontal polymerization. The appropriate amounts of VI, HEA, and ammonium persulfate (APS)/N,N,N′,N′‐tetramethylethylenediamine (TMEDA) couple redox initiator were mixed together at ambient temperature in the presence of glycerol as the solvent medium. Frontal polymerization (FP) was initiated by heating the upper side of the mixture with a soldering iron. Once initiated, no further energy was required for the polymerization to occur. The dependence of the front velocity and front temperature on the VI/HEA weight ratios were investigated. The pH sensitive behavior, morphology, and heavy metal removal study of poly(VI‐co‐HEA) hydrogels prepared via FP were comparatively investigated on the basis of swelling measurements, scanning electron microscopy, and inductively coupling plasma spectrometer. Results show that the poly(VI‐co‐HEA) hydrogels prepared via FP exhibit good pH sensitivity and adsorption capacity. The FP can be exploited as an alternative means for synthesis of pH sensitive hydrogels in a fast and efficient way. The as‐prepared hydrogels can be applied to remove heavy metals. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4005–4012, 2010     

High performance of interpenetrating polymer network hydrogels induced by frontal polymerization

We report the rapid synthesis of hydrogels with interpenetrating polymer networks (IPNs) by frontal polymerization (FP). Appropriate amounts of diacetone acrylamide (DAAM), N-methylolacrylamide (NMA), thermoplastic polyurethane (TPU), N,N′-methylenebisacrylamide (MBAA), and ammonium persulfate (APS)/N,N,N′,N′-tetramethylethylenediamine (TMEDA) were mixed together at ambient temperature. FP was initiated by transitorily heating the upper side of the reactants, and poly(DAAM-co-NMA)/TPU IPN hydrogels were obtained within minutes. The preparation parameters were thoroughly investigated. Moreover, we investigated the morphology, swelling capacity, chemical structure and the mechanical properties of poly(DAAM-co-NMA)/TPU IPN hydrogels, along with those of poly(DAAM-co-NMA) hydrogels without IPN structure for comparison. Interestingly, the mechanical strength of poly(DAAM-co-NMA)/TPU IPN hydrogels is notably improved in comparison with that of poly(DAAM-co-NMA) hydrogels. The results indicate that the IPN structure endows hydrogels with high mechanical strength, and FP can be applied as an alternative means for synthesis of IPN hydrogels with additional advantages of speed and efficiency.     

Solvent‐free free‐radical frontal polymerization: A new approach to quickly synthesize poly(N‐vinylpyrrolidone)

The first synthesis of poly(N‐vinylpyrrolidone) without solvent by free‐radical frontal polymerization at ambient pressure is reported. The appropriate amounts of two reactants N‐vinyl‐2‐pyrrolidone (NVP) and initiator 2,2′‐azobis‐isobutyronitrile (AIBN) without solvent were mixed together at ambient temperature. Frontal polymerization was initiated by heating the wall of the tube with a soldering iron, and the resultant hot fronts were allowed to self‐propagate throughout the reaction vessel. Once initiated, no further energy was required for polymerization to occur. To suppress the fingers of molten monomer, a small amount of nanosilica was added. The dependence of the front velocity and front temperature on the AIBN concentration was thoroughly investigated. The as‐prepared polymers were characterized by gel permeation chromatography (GPC) and thermogravimetric analysis (TGA). Results show that without postpolymerization solvent removal, waste production can be reduced. Solvent‐free FP could be exploited as a means for preparation of PVP with the potential advantage of higher throughput than solvent‐based methods. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2177–2185, 2008     

Facile and quick synthesis of poly(N‐methylolacrylamide)/polyhedral oligomeric silsesquioxane graft copolymer hybrids via frontal polymerization

We report on a new strategy for fabricating well‐defined POSS‐based polymeric materials with and without solvent by frontal polymerization (FP) at ambient pressure. First, we functionalize polyhedral oligomeric silsesquioxane (POSS) with isophorone diisocyanate (IPDI). With these functionalized POSS‐containing isocyanate groups, POSS can be easily incorporated into a poly(N‐methylolacrylamide) (PNMA) matrix via FP in situ. Constant velocity FP is observed without significant bulk polymerization. The morphology and thermal properties of POSS‐based hybrid polymers prepared via FP are comparatively investigated on the basis of scanning electronic microscopy (SEM) and thermogravimetric analysis (TGA). Results show that the as‐prepared POSS‐based polymeric materials exhibit a higher glass transition temperature than that of pure PNMA, ascribing to modified POSS well‐dispersed in these hybrid polymers. Also, the products with different microstructures display different thermal properties. The pure PNMA exhibits a featureless morphology, whereas a hierarchical morphology is obtained for the POSS‐based polymeric materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1136–1147, 2009     

Semi‐interpenetrating polymer networks based on crosslinked poly(N‐isopropyl acrylamide) and methylcellulose prepared by frontal polymerization

In this work, semi‐interpenetrating gels of poly(N‐isopropyl acrylamide) and methylcellulose were successfully synthesized by using the Frontal Polymerization (FP) technique. The gels were obtained in the presence of dimethyl sulfoxide and trihexyltetradecylphosphonium persulfate, as polymerization solvent and radical initiator, respectively, hence avoiding the formation of bubbles during polymerization. Then, some of the gels containing dimethyl sulfoxide were thoroughly washed with water, hence obtaining the corresponding hydrogels. The effects of the ratio between poly(N‐isopropyl acrylamide) and methylcellulose, the amount of crosslinker and solvent medium (i.e., dimethyl sulfoxide and water) were thoroughly studied, assessing the influence of temperature and velocity of FP fronts on the glass transition temperature values (dried samples), on the swelling behavior and on the dynamic‐mechanical properties (gels swollen both in water and dimethyl sulfoxide). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 437–443     

Frontal free‐radical copolymerization of urethane–acrylates

We report the first synthesis of urethane–acrylate copolymers via free‐radical frontal polymerization. In a typical run, the appropriate amounts of the reactants (urethane–acrylate macromonomer and 2‐hydroxyethyl acrylate) and initiator (ammonium persulfate) were dissolved in dimethyl sulfoxide. Frontal polymerization was initiated by the heating of the wall of the tube with a soldering iron, and the resultant hot fronts were allowed to self‐propagate throughout the reaction vessel. Once it was initiated, no further energy was required for the polymerization to occur. The dependence of the front velocity and front temperature on the initiator concentration was investigated. The front temperatures were between 55 and 65 °C, depending on the persulfate concentration. Thermogravimetric analysis indicated that the urethane–acrylate copolymers had higher thermal stability than pure frontally prepared polyurethane. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3018–3024, 2006     

Facile synthesis of fluorescent quantum dot‐polymer nanocomposites via frontal polymerization

We report an available approach for quickly fabricating CdS QD‐polymer nanocomposites via frontal polymerization (FP). First, we synthesized (3‐mercaptopropyl)‐1‐trimethoxysilane (MPS)‐capped CdS quantum dots (QDs). With these MPS‐capped CdS QDs containing mercapto groups, MPS‐capped CdS QDs can be easily incorporated into a poly(N‐methylolacrylamide) (PNMA) matrix via FP. A variety of features for preparing QD‐polymer nanocomposites, such as initiator concentration and CdS concentration, were thoroughly investigated. The fluorescence properties of QD‐polymer nanocomposites prepared via FP are comparatively investigated on the basis of ultraviolet–visible (UV–vis) spectra and photoluminescence (PL) spectra. Results show that the PL intensity of QD‐polymer nanocomposites prepared via the FP method is superior to that obtained by the traditional batch polymerization (BP) method. In addition, by measuring the changes of PL intensity of the samples immersed in different concentrations of copper acetate solution, we found the QD‐polymer nanocomposites can be ultrasensitive to copper ions. This FP process can be exploited as a facile and rapid way for synthesis QD‐polymer nanocomposites on a large scale, avoiding the fluorescence quenching of nanocrystals during incorporation nanocrystals into polymer matrices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2170–2177, 2010     

Methacrylic acid and methyl methacrylate oligomers adsorbed to porous isotactic poly(methyl methacrylate) ultrathin films and mechanistic studies of living template polymerization

Methacrylic acid (MAA), methyl methacrylate (MMA), methacrylamide, and oligomers of MAA and MMA were selected as a model of active radical species in living template polymerization using stereocomplex formation. The adsorption behaviors of the aforementioned model compounds were examined toward porous isotactic‐(it‐) poly(methyl methacrylate) (PMMA) ultrathin films on a quartz crystal microbalance, which was prepared by the extracting of syndiotactic‐(st‐) poly(methacrylic acid) (PMAA) from it‐PMMA/st‐PMAA stereocomplexes. The apparent predominant adsorption of oligomers to monomers was observed in both PMAA and PMMA oligomers, suggesting that the mechanism of template polymerization follows the pick up mechanism. Although vinyl monomers were not incorporated into the porous it‐PMMA ultrathin film, both PMMA and PMAA oligomers were adsorbed at the initial stages. However, adsorbed amounts were limited to about 5 and 15% at 0.1 mol L^?1, respectively, which are much smaller values than corresponding st‐polymers. The results imply that radical coupling reaction is prevented during template polymerization to support the resulting living polymerization. ATR‐IR spectral patterns of oligomer complexes and it‐PMMA slightly changed in both cases, suggesting complex formation. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5879–5886, 2008     

Preparation and optical characterization of two photoactive poly(bisphenol a ethoxylate diacrylate) copolymers containing designed amino‐nitro‐substituted azobenzene units,obtained via classical and frontal polymerization,using novel ionic liquids as initiators

The frontal polymerization (FP) of bisphenol A ethoxylate diacrylate (BPAEDA) was carried with and without the presence of two different azobenzene comonomers by means of an external heating source. The first azomonomer (MDR‐1) is a derivative of disperse red‐1, N‐ethyl‐N‐(2‐hydroxyethyl)‐4‐(4‐nitrophenylazo)aniline, whereas the second (E)‐2‐(4‐((4‐nitrophenyl)diazenyl)phenyl)‐5,8,11‐trioxa‐2‐azatridecan‐13‐yl methacrylate (4PEGMAN) comes from the azo‐dye N‐methyl‐N‐{4‐[(E)‐(4‐nitrophenyl)diazenyl]phenyl}‐N‐(11‐hydroxy‐3,6,9‐trioxaundecas‐1‐yl) amine. In this work, an ionic liquid trihexyltetradecylphosphonium persulfate was used as initiator. This compound produced stable propagating polymerization fronts with good velocities and moderate maximum temperature values. Moreover, this initiator prevented bubble formation and was found to be the most efficient when it was used in lower amounts with respect to other initiators, such as benzoyl peroxide, 2,2′‐azobisisobutyronitrile, aliquat persulfate®, and tetrabutylphosphonium persulfate. The thermal properties of the obtained polymers and copolymers were determined by thermogravimetric analysis and differential scanning calorimetry. The nonlinear optical (NLO) characterizations of the developed BPAEDA/MDR‐1 and BPAEDA/4PEGMAN copolymers were performed according to the Z‐Scan technique in film samples prepared by classical polymerization. It has been proven that samples with higher 4PEGMAN content (0.26 mol %) exhibited outstanding cubic NLO‐activity with positive NLO‐refractive coefficients in the promising range of n₂ = +3.2 × 10^?4 esu. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Temperature effect on template polymerization of methacrylic acid using stereocomplex formation on quartz crystal microbalance substrates

The radical polymerization of methacrylic acid (MAA) at 0, 20, 40, and 70 °C was achieved in porous isotactic (it‐) poly(methyl methacrylate) (PMMA) films on quartz crystal microbalance (QCM) substrates, which were prepared by layer‐by‐layer assembled stereocomplex films of it‐PMMA and syndiotactic (st‐) poly(methacrylic acid) (PMAA), followed by the subsequent extraction of st‐PMAA. The MAA polymerization yields increased from 35 to 75%, as the polymerization temperature increased from 0 to 70 °C. Furthermore, infrared spectroscopy revealed that a higher polymerization temperature is necessary to form it‐PMMA/st‐PMAA stereocomplexes via stereoregular polymerization manner that resemble native it‐PMMA/st‐PMAA stereocomplexes. X‐ray diffraction pattern of porous it‐PMMA were also investigated for reaction fields. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3032–3036     

Synthesis and self‐assembly of thymine‐ and adenine‐containing homopolymers and diblock copolymers

Atom transfer radical polymerizations (ATRPs) of 1‐(4‐methacryloyloxy‐benzyl)thymine (MAT) and 9‐(2‐methacryloyloxyethyl)adenine (MAA) were conducted for the synthesis of DNA‐base functionalized polymers. The association equilibrium constant K_asso between MAT and MAA and the complexation equilibrium constant K_comp between the corresponding polymers PMAT and PMAA were determined. A zipper‐like diblock copolymer, PMAT‐b‐PMAA, was prepared by anchoring the PMAT and PMAA blocks on the ortho‐positions of a pyridine ring via a successive two‐step ATRP. Dynamic light scattering and atom force microscopy confirmed that the block copolymer had a V‐shaped configuration in dimethylsulfoxide/N,N‐dimethylformamide. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5995–6006, 2006     

Synthesis and stability of BODIPY‐based fluorescent polymer brushes at different pHs

We report a simple strategy for the grafting of poly(methacrylic acid) [poly(MAA)] brushes from silicon substrate by surface‐initiated RAFT polymerization and the subsequent coupling of BODIPY to these brushes to render them fluorescent. The poly(MAA) brushes were first generated by functionalization of hydrogen‐terminated silicon substrate with methyl‐10‐undecenoate which both leads to the formation of an organic layer covalently linked to the surface via Si? C bonds without detectable reaction of the carboxylate groups and couples to the polymerization initiator, followed by surface‐initiated RAFT polymerization of tert‐butyl methacrylate from these substrate‐bound initiator centers, and finally conversion of tert‐butyl groups to carboxylic acid groups. The poly(MAA) brushes were then made fluorescent by grafting a BODIPY derivative via an ester linkage. The stability of the BODIPY‐based fluorescent polymer brushes in buffer solutions at pH 6.0 to 12.0 with added salt was investigated by ellipsometry, fluorescence microscopy, grazing angle‐Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy. The results of these measurements indicated that the organic molecule‐initiator bond (ester linkage) is unstable and can be hydrolyzed resulting in detaching of the immobilized polymer from the silicon substrate. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3586–3596     

Fast fabrication of superabsorbent polyampholytic nanocomposite hydrogels via plasma‐ignited frontal polymerization

We report the facile synthesis of poly(VI‐co‐MAA) superabsorbent polyampholytic hydrogels (VI = N‐vinylimidazole, MAA = methacrylic acid) via plasma‐ignited frontal polymerization (PIFP). On igniting the top surface of the reactants with air plasma, frontal polymerization occurred and poly(VI‐co‐MAA) hydrogels were obtained within minutes. The preparation parameters were investigated, along with swelling capacity, morphology, and chemical structures of poly(VI‐co‐MAA) hydrogels. Interestingly, the hydrogels are superabsorbent in water and show ampholytic characteristic toward pH. Moreover, the hydrogels are able to capture cationic dyes through electrostatic interaction, offering the potential for further development as dye adsorbents for water purification. In addition, nanocomposite hydrogels were obtained by embedding quantum dots (carbon dots or CdS nanocrystals) into the polymer matrix, which endows the nanocomposite hydrogels with favorable fluorescence and potential applications in bioimaging and biosensing. The results indicate that FP can be applied as an alternative means for facile synthesis of multifunctional hydrogels with additional efficiency and energy‐saving. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 912–920     

Preparation of a thermo- and pH-sensitive nanofibrous scaffold with embedded chitosan-based nanoparticles and its evaluation as a drug carrier

Environmentally sensitive poly(N-isopropylacrylamide) (PNIPAAm) nanofibrous scaffolds loaded with a hydrophilic drug were fabricated via an electrospinning process. First, thermally crosslinkable poly(NIPAAm-co-N-methylolacrylamide) (PNN) was synthesized by redox polymerization below the phase transition temperature of PNIPAAm. The phase transition temperature of the PNN copolymer could be altered from 34 to 40 °C by changing the ratio of N-methylolacrylamide (NMA) to NIPAAm. Subsequently, PNN/chitosan nanofibers were electrospun using ethanol/acetic acid/water as a cosolvent. The PNN/chitosan nanofibers were sensitive to both pH and temperature. The fibrous structure of the soaked PNN/chitosan nanofibers was successfully preserved by the crosslinking of NMA. Furthermore, the chitosan-based nanoparticles (NPs) were introduced into the PNN nanofibers (PNN/NPs) to achieve prolonged drug release. The nanoparticles were observed in the PNN nanofibers by transmission electron microscopy. All of the scaffolds examined had high tensile strengths (1.45 MPa or above) and exhibited no significant cytotoxicity toward human fetal skin fibroblasts. Finally, doxycycline hyclate was used as a model drug. The results illustrated that PNN/NPs nanofibrous scaffolds exhibited continuous drug release behavior for up to 1 week, depending on the pH and temperature.     

Spontaneous Cu(I)Br–PMDETA‐mediated polymerization of isobornyl methacrylate in heterogeneous aqueous medium at ambient temperature

Isobornyl methacrylate (IBMA), a bulky hydrophobic methacrylate, undergoes very fast polymerization, in bulk, with Cu(I)Br/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA)/ethyl‐2‐bromoisobutyrate system, at ambient temperature. IBMA also undergoes a spontaneous initiator‐free polymerization, at ambient temperature, with Cu(I)Br/PMDETA catalytic system in dimethyl sulfoxide–water mixtures. The rate of the polymerization is seen to increase with the water content up to 80 mol % of water. A possible intervention of air in initiation is proposed. The active Cu(0) formed by the disproportionation of Cu(I) species in aqueous medium probably plays a vital role for a possible air‐initiation of IBMA via single electron transfer‐living radical polymerization (SET‐LRP) mechanism. A high tolerance level to water under SET‐LRP conditions is demonstrated. The poly(IBMA) samples obtained exhibit low molecular weight distributions (1.1–1.3). Similar behavior was not observed with other common methacrylates such as methyl methacrylate, t‐butyl methacrylate, cyclohexyl methacrylate, and benzyl methacrylate. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A new strategy to prepare temperature-sensitive poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) microgels

In this study, a new method was developed to prepare temperature-sensitive poly(N-isopropylacrylamide) microgels by free radical precipitation polymerization using siloxane coupling agent as the new crosslinker. Ammonium persulfate acted as the initiator for the radical copolymerization as well as the catalyst for the hydrolysis/condensation of the siloxane groups. The particle diameter and polydispersity of the microgels were measured by photon correlation spectroscopy and the results display that the microgels are monodisperse. The microgels exhibit temperature sensitivity and the phase transition temperature is approximately 31 °C. Furthermore, the diameter of the microgels changes upon heating and cooling processes. These were observed to be reversible. The novel crosslinking method described herein is the condensation of siloxane groups, which is totally different from the traditional double-vinyl crosslinkers. This innovative approach offers an alternative path to prepare functional core–shell particles and inorganic/organic hybrid materials.     

Reverse atom transfer radical polymerization of methyl methacrylate initiated by p‐chlorobenzenediazonium tetrafluoroborate

The controlled polymerization of methyl methacrylate (MMA) in bulk was initiated with p‐chlorobenzenediazonium tetrafluoroborate ( 1 ) and Cu(II) or Cu(I)/Cu(II)/N,N,N′,N″,N″‐pentamethyldietylene triamine (PMDETA) complex system at various temperatures (20, 60, and 90 °C). The proposed polymerization mechanism is based on the Meerwein‐type arylation reaction followed by a reverse atom transfer radical polymerization. In this mechanism, aryl radicals formed by the reaction with 1 and Cu(I) and/or PMDETA initiated the polymerization of MMA. The polymerization is controlled up to a molecular weight of 46,000 at 90 °C. Chain extension was carried out to confirm the controlled manner of the polymerization system. In all polymerization systems, the polydispersity index and initiator efficiency ranged from 1.10–1.57 to 0.10–0.21, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2019–2025, 2003