One-pot synthesis of CoO–ZnO/rGO supported on Ni foam for high-performance hybrid supercapacitor with greatly enhanced cycling stability

The high specific capacitance along with good cycling stability are crucial for practical applications of supercapacitors,which always demands high-performance and stable electrode materials.In this work,we report a series of ternary composites of CoO-ZnO with different fractions of reduced graphene oxide(rGO) synthesized by in-situ growth on nickel foam,named as CZG-1,2 and 3,respectively.This sort of binder-free electrodes presents excellent electrochemical properties as well as large capacitance due to their low electrical resistance and high oxygen vacancies.Particularly,the sample of CZG-2(CoO-ZnO/rGO 20 mg) in a nanoreticular structure shows the best electrochemical performance with a maximum specific capacitance of 1951.8 F/g(216.9 mAh/g) at a current intensity of 1 A/g.The CZG-2-based hybrid supercapacitor delivers a high energy density up to 45.9 Wh/kg at a high power density of 800 W/kg,and kept the capacitance retention of 90.1% over 5000 charge-discharge cycles.     

NF/rGO/Co_3O_4/NiO电极的制备及在超级电容器中的应用

以泡沫镍(NF)为集流体,在优化好的电位、时间和浓度下,将还原氧化石墨烯(rGO)、金属氧化物(Co_3O_4和NiO)直接生长在泡沫镍上,制备了NF/rGO/Co_3O_4和NF/rGO/Co_3O_4/NiO电极.运用三电极体系对电极材料进行了恒流充放电(GCD)和交流阻抗(EIS)等测试.结果表明,复合材料NF/rGO/Co_3O_4/NiO具有较高的比容量(电流密度为2 A/g时,比容量达到1188.6 F/g)和较好的循环稳定性(2000周充放电后,稳定性达到80.5%).该材料还具有较高的倍率性能,当电流密度由2 A/g增至12 A/g时,倍率性能仍能达到75.7%.     

NiO/rGO的溶剂热合成以及作为高循环稳定性超级电容器电极材料的性能表征

通过简单的溶剂热法以及其后续热处理过程,制备了NiO纳米花和NiO/还原氧化石墨烯（rGO）复合物。 在NiO/rGO复合物中,rGO作为基底生长NiO,与此同时,NiO则有效的避免了rGO的团聚。 采用热重分析(TG)、场发射扫描电子显微镜(FE-SEM)和X射线衍射对样品的成分、形貌和结构进行了表征。 NiO/rGO复合物（NiO和rGO的质量比为82.7∶17.3）电极呈现优异的电化学性能。 在1 A/g时,初始比电容为514.9 F/g,当材料完全活化后,其比电容高达600 F/g。 同时,在电流密度为10 A/g时,相比于1 A/g时的比电容保持率为83.5%。 此外,该电极材料具有非常优异的循环稳定性,6000次循环后电容衰减率为7.4%。 表明所制备的复合物是一种有应用价值的超级电容器电极材料。     

Three-dimensional flower-like nickel oxide supported on graphene sheets as electrode material for supercapacitors

Dispersed three-dimensional (3D) flower-like nickel oxide on graphene sheets was synthesized by incorporating a facile hydrothermal process with a thermal treatment process. The possible growth mechanism of 3D flower-like NiO is discussed. When used as electrode materials for supercapacitors, the resultant composite exhibits a specific capacitance of 346F/g (1.5A/g), a good rate performance and cycle stability in 2?M KOH. NiO in the composite could provide a specific capacitance as high as 778.7F/g, compared to that of bare NiO of only 220F/g. The functional features of unique 3D flower-like NiO morphology, high conductivity of graphene sheets and its protective effect to the structure of NiO result in an improved electrochemical performance.     

功能型单层石墨烯的热剥离法制备及其超电容性能

以氧化石墨(GO)作为前驱体,在两种不同热剥离温度下制备了两类功能型单层石墨烯.其中第一类功能型单层石墨烯通过在较低温度及空气气氛下热剥离GO制备;第二类功能型单层石墨烯通过在氮气保护下高温热剥离GO得到;利用氮气吸附-脱附方法测定了两类样品的比表面积,利用电化学测试方法分析了其超电容性能.结果表明,通过低温热剥离的方式即可以有效剥离GO;两类样品均具有较高的BET比表面积.低温热剥离GO所制备的功能型单层石墨烯在2 mol/L KOH体系中的最大比电容值约为220 F/g;而通过高温热剥离GO所制备的功能型单层石墨烯虽然同样具有较高的BET比表面积,但其最大比电容值下降至约150 F/g.这表明通过低温热剥离GO所制备的功能型单层石墨烯具有更优异的超电容性能.     

Activated carbon/graphene composites with high-rate performance as electrode materials for electrochemical capacitors

Glucose-derived activated carbon (GAC)/reduced graphene oxide (RGO) composites are prepared by pre-carbonization of the precursors (aqueous mixture of glucose and graphene oxide) and KOH activation of the pyrolysis products. The effect of the mass ratio of graphene oxide (GO) in the precursor on the electrochemical performance of GAC/RGO composites as electrode materials for electrochemical capacitors is investigated. It is found that the thermally reduced graphene oxide sheets serves as a wrinkled carrier to support the activated carbon particles after activation. The pore size distribution and surface area are depended on the mass ratio of GO. Besides, the rate capability of GAC is improved by the introduction of GO in the precursor. The highest specific capacitance of 334 F g^?1 is achieved for the GAC/RGO composite prepared from the precursor with a GO mass ratio of 3 %.     

Hollow Co9S8 from metal organic framework supported on rGO as electrode material for highly stable supercapacitors

We demonstrate a hydrothermal method to fabricate a composite of reduced graphene oxide (rGO) with hollow Co₉S₈ derived from metal organic framework (MOF), which exhibits a high specific capacitance of 575.9 F/g at 2 A/g and 92.0% capacitance retention after 9000 cycles.     

Enhanced Supercapacitor Performance Using a Co3O4@Co3S4 Nanocomposite on Reduced Graphene Oxide/Ni Foam Electrodes

To avoid an enormous energy crisis in the not-too-distant future, it be emergent to establish high-performance energy storage devices such as supercapacitors. For this purpose, a three-dimensional (3D) heterostructure of Co₃O₄ and Co₃S₄ on nickel foam (NF) that is covered by reduced graphene oxide (rGO) has been prepared by following a facile multistep method. At first, rGO nanosheets are deposited on NF under mild hydrothermal conditions to increase the surface area. Subsequently, nanowalls of cobalt oxide are electro-deposited on rGO/Ni foam by applying cyclic-voltammetry (CV) under optimized conditions. Finally, for the synthesis of Co₃O₄@Co₃S₄ nanocomposite, the nanostructure of Co₃S₄ was fabricated from Co₃O₄ nanowalls on rGO/NF by following an ordinary hydrothermal process through the sulfurization for the electrochemical application. The samples are characterized by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The obtained sample delivers a high capacitance of 13.34 F cm⁻² (5651.24 F g⁻¹) at a current density of 6 mA cm⁻² compared to the Co₃O₄/rGO/NF electrode with a capacitance of 3.06 F cm⁻² (1230.77 F g⁻¹) at the same current density. The proposed electrode illustrates the superior electrochemical performance such as excellent specific energy density of 85.68 W h Kg⁻¹, specific power density of 6048.03 W kg⁻¹ and a superior cycling performance (86% after 1000 charge/discharge cycles at a scan rate of 5 mV s⁻¹). Finally, by using Co₃O₄ @Co₃S₄/rGO/NF and the activated carbon-based electrode as positive and negative electrodes, respectively, an asymmetric supercapacitor (ASC) device was assembled. The fabricated ASC provides an appropriate specific capacitance of 79.15 mF cm⁻² at the applied current density of 1 mA cm⁻², and delivered an energy density of 0.143 Wh kg⁻¹ at the power density of 5.42 W kg⁻¹.     

High-performance supercapacitor based on ultralight and elastic three-dimensional carbon foam/reduced graphene/polyaniline nanocomposites

A novel supercapacitor based on ultralight and elastic three-dimensional porous melamine foam-derived macroporous carbon/reduced graphene oxide/polyaniline nanocomposites were fabricated, which showed great electrical performance and cycle performance.     

Graphene materials preparation methods have dramatic influence upon their capacitance

Graphene related materials are widely expected to play a major role as materials for the construction of supercapacitors. We demonstrate here that graphene oxides prepared by various well-established methods exhibit dramatically different capacitances. We exfoliated graphite oxide sonographically to graphene oxide (GO) and we reduced GO by chemical or electrochemical means to chemically reduced graphene oxide (CRGO) and electrochemically reduced graphene oxide (ERGO); in addition, graphite oxide was thermally exfoliated leading to thermally reduced graphene oxide (TRGO). We found clear dependence of weight specific capacitance upon amount of oxygen containing groups presented on the surface of these graphenes. GO exhibits the lowest and TRGO the highest values of weight specific capacitance.     

Segregated reduced graphene oxide polymer composite as a high performance electromagnetic interference shield

Herein, we report the synthesis of a graphene/polymer composite via a facile and straightforward approach for electromagnetic interference (EMI) shielding applications. Polystyrene (PS) beads were added in graphene oxide (GO)/water solution followed by the addition of hydroiodic acid (HI) for in situ reduction of GO. The composite solution (rGO/PS) was filtered, hot compressed and tested for EMI shielding and dielectric measurements. A 2-mm thick segregated rGO/PS sample with 10 wt% filler loading delivered a high EMI shielding effectiveness (SE) of 29.7 dB and an AC electrical conductivity of 21.8 S m^?1, which is well above the commercial requirement for EMI shielding applications. For comparison with the segregated rGO/PS composite, a control polymer composite sample utilizing a thermally reduced graphene oxide was synthesized by following a conventional coagulation approach. The as-synthesized conventional rGO/PS yield an EMI SE of 14.2 dB and electrical conductivity of 12.5 S m^?1. The high EMI shielding of segregated rGO/PS is attributed to the better filler-to-filler contact among graphene layers surrounded by PS beads and also to the better reduction and preservation of graphene structure during reduction process that makes the low temperature chemically reduced segregated rGO/PS approach a viable route compared to high temperature thermally reduced conventional rGO/PS approach.     

Ni3(HCOO)6/还原氧化石墨烯复合电极材料的制备及电容性能

以氧化石墨烯(GO)为前驱体, Ni(NO₃)₂·6H₂O为镍源, 甲酸为配体, N,N-二甲基甲酰胺为溶剂, 通过一步溶剂热法制备了Ni₃(HCOO)₆/rGO复合电极材料. 研究结果表明, 通过金属镍离子和配体在氧化石墨烯表面超分子自组装成核, 形成了“三明治”式的夹心复合结构; 不同的GO浓度对复合材料的物相结构、 晶体尺寸大小、 形貌及电化学性能有很大的影响; 当GO的浓度为8 mg/mL时, 在100 ℃下反应24 h得到的Ni₃(HCOO)₆/rGO复合材料在电解液为1 mol/L KOH, 5 mV/s下比电容高达940 F/g, 经过500次充放电循环后电容的保持率为96.28%.     

Ultrafast room-temperature reduction of graphene oxide by sodium borohydride,sodium molybdate and hydrochloric acid

Since graphene-based materials have shown great potential in many fields,it is important to explore ultrafast and high-efficient methods to synthesize reduced graphene oxide(rGO) using inexpensive reducing agents under mild conditions.Here,we reported a novel method for the ultrafast chemical reduction of graphene oxide(GO) at room temperature using sodium borohydride(NaBH₄),sodium molybdate(Na₂MoO₄) and hydrochloric acid(HCl).The reduction was carried out within 2 min.A series of characterization results revealed that the obtained reduced graphene oxide has higher reduction degree than that synthesized by NaBH₄ alone at high temperature.Moreover,rGO electrode based on the present reducing method exhibited a superior specific capacitance of 139.8 F/g at a current density of1 A/g,indicating that it can be used as electrode materials for supercapacitors.     

石墨烯/聚吡咯纳米纤维超级电容器电极材料的制备及其电化学性能

超级电容器因其具有较高的循环稳定性和较好的能量密度而成为储能器件中的研究热点,其电极材料及制备方法是决定超级电容器电化学性能的关键因素。 本文以聚环氧乙烷-聚环氧丙烷-聚环氧乙烷三嵌段共聚物(P123)为软模板,通过一步原位聚合法成功地制备了石墨烯/聚吡咯纳米纤维(GR/PPy NF)复合超级电容器电极材料。 通过X射线衍射(XRD),X射线光电子能谱(XPS)、透射电子显微镜(TEM)和傅里叶变换红外光谱仪(FT-IR)等对复合材料的结构和形态进行了系统的表征。 利用电化学方法对GR/PPy NF复合电极材料的电化学性能进行了系统的分析。 结果表明,在电流密度0.5 A/g下,纳米复合材料的比电容量高达969.5 F/g,在充放电600圈之后,仍可保留初始比电容的88%,展示了良好的电容性能及循环稳定性。 GR/PPy NF制备简单,性能优异,是一种很有前途的能量转换/存储材料。     

氧化石墨烯浓度对还原氧化石墨烯/ZnS电化学性能的影响

以氧化石墨烯(GO)、乙酸锌(Zn(CH₃COO)₂)和硫脲为原料,采用水热法成功制备了还原氧化石墨烯/ZnS(rGO/ZnS)复合材料,并将该材料用作锂离子电池负极。高导电性的 rGO可以为锂离子和电子的传输提供有效的路径,ZnS可以提供较高的理论比容量。rGO/ZnS复合材料在rGO与纳米级高度分散的类球形ZnS颗粒协同作用下展现了较好的嵌锂容量和循环性能。当GO质量浓度为2 mg·mL^-1时制备的rGO/ZnS复合材料的倍率性能最好,循环稳定性最佳。     

Synthesis and Electrochemical Performance of Co3O4/Graphene

Co3O4/reduced graphene oxide composites were synthesized via a simple electrochemical method from graphene oxide and Co（NO3）2·6H2O as raw materials.Co3O4 nanoparticles with sizes of around 30-50 nm were distributed on the surface of graphene nanosheets confirmed by scanning electron microscopy and transmission electron microscopy.Electrochemical properties of Co3O4/graphene composite were tested by cyclic voltammetry,galvanostatic charge-discharge,and electrochemical impedance spectroscopy.The Co3O4/reduced graphene oxide composite was used as the pseudocapacitor electrode in the 2 mol/L NaOH aqueous electrolyte solution.The Co3O4/reduced graphene oxide composite electrode exhibited a specific capacitance of 357 F/g at a current density of 0.5 A/g in a three-electrode system.72％ of capacitance was retained when the current density increased to 3 A/g.The Co3O4/reduced graphene oxide composite prepared electrodes show a high rate capability and excellent long-term stability.After 1000 cycles of charge and discharge,the capacitance is still maintained 87％ at a current density of 1 A/g,indicating that the composite is a oromising alternative electrode material used for supercapacitors.     

磷酸钒锂/石墨烯复合正极材料的制备及表征

通过三聚氰胺甲醛树脂(MR)中的羟基与石墨烯氧化物(GO)中的羧基发生的沉淀反应来制备功能化的氧化石墨烯前驱体,然后利用溶胶-凝胶及高温热处理方法制备磷酸钒锂/石墨烯复合材料,利用此材料制备了电池电极,并对电极材料进行了结构和电化学表征。结果表明,所得磷酸钒锂为单斜晶系结构,石墨烯堆叠程度显著降低,也有效避免了磷酸钒锂颗粒的团聚,提高了材料的电化学性能。电池的充放电曲线极化较小,在3.0~4.3 V的区间内20 C倍率仍有86 mA·h/g的可逆容量。0.1 C循环100次后容量为119.7 mA·h/g,容量保持率94%。在3.0~4.8 V的高电压区间,10 C倍率下可逆容量80 mA·h/g,0.1 C循环100次后仍有145.6 mA·h/g的可逆容量。优异的循环和倍率性能以及较低的碳含量符合锂离子正极材料实用的要求。     

Electrochemical Preparation of Polypyrrole/Graphene Films on Titanium Mesh as Active Materials for Supercapacitors

Films of polypyrrole/graphene on titanium mesh were prepared by electrochemical reduction of the fresh dried foam films of graphene oxide followed by an electrochemical polymerization of pyrrole. The as-obtained composite had highly surface area, conductivity, and could be used as the electrode for supercapacitors, especially directly used as the active materials in free of binders while the Ti mesh worked as the collector. Plenty of polypyrrole nanoparticles formed on the surface of reduced graphene film, and some fiber-like aggregates could be formed during the polymerization, which worked as the material for pseudo-capacitance. The specific capacitance of the supercapacitor reached 400 F/g and showed high stability with retaining capacitance of 82% after 5000 cycles, indicating that the nanocomposite is a suitable active material for supercapacitors.     

水热法制备Fe3O4/rGO纳米复合物作为锂离子电池阳极材料

以氢氧化铁为四氧化三铁的前驱体,氧化石墨烯（GO）为还原石墨烯（rGO）的前驱体,以水合肼和二水合柠檬酸三钠为混合还原剂,采用水热法制备了还原石墨烯负载四氧化三铁纳米颗粒（Fe₃O₄/rGO）的复合材料。通过透射电子显微镜（TEM）、X-射线衍射（XRD）和热重分析（TGA）对产物的形貌、结构和组成进行了表征。以锂片为对电极进行了扣式电池的组装,通过恒电流充放电和循环伏安法对其电化学性能进行了测试。材料具有均一的形貌,rGO具有较高的还原程度且可以在充放电过程中缓冲Fe₃O₄纳米颗粒的体积变化,使得Fe₃O₄/rGO纳米复合物具有较好的电化学性能。     

Free‐standing and Flexible MoS2/rGO Paper Electrode for Amperometric Detection of Folic Acid

The development of flexible electrodes is of considerable current interest because of the increasing demand for modern electronics, portable medical products, and compact devices. We report a new type of flexible electrochemical sensor fabricated by integrating graphene and MoS₂ nanosheets. A highly flexible and free‐standing conductive MoS₂ nanosheets/reduced graphene oxide (MoS₂/rGO) paper was prepared by a two‐step process: vacuum filtration and chemical reduction treatment. The MoS₂/graphene oxide (MoS₂/GO) paper obtained by a simple filtration method was transformed into MoS₂/rGO paper after a chemical reduction process. The obtained MoS₂/rGO paper was characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy, electrochemical impedance spectroscopy. The electrochemical behavior of folic acid (FA) on MoS₂/rGO paper electrode was investigated by cyclic voltammetry and amperometry. Electrochemical experiments indicated that flexible MoS₂/rGO composite paper electrode exhibited excellent electrocatalytic activity toward the FA, which can be attributed to excellent electrical conductivity and high specific surface area of the MoS₂/rGO paper. The resulting biosensor showed highly sensitive amperometric response to FA with a wide linear range.