原子荧光光谱法测定环境水中砷、硒和汞

原子荧光光谱法测定环境水中砷、硒和汞,试验了标准系列的配制方法;硼氢化钾浓度、盐酸酸度对测定的影响;优化了仪器条件。砷、硒和汞检出限分别为0.51μg/L、0.53μg/L、0.065μg/L,相对标准偏差(n=11)分别为1.51%、2.36%、1.63%,加标回收率分别为90.0%-105.0%、92.0%-97%、90.0%-97.5%。     

氢化物-原子荧光光谱法测定金属饰品中的砷和汞

采用氢化物-原子荧光光谱法测定金属饰品中砷和汞.用体积比为3:1的浓硝酸和浓盐酸微波消解样品.结果表明:砷和汞方法的检出限分别为0.079μg/L和0.037μg/L;砷、汞RSD分别为1.89%和4.82%;砷的加标回收率为99.6%,汞的加标回收率为96.0%.该方法快速简便,能满足饰品的日用检验要求.     

双道原子荧光光谱法同时测定农产品中的砷和硒

研究了AFS-930型双道原子荧光光度计同时测定农产品中砷和硒的方法.该法快速,简便,准确,砷回收率为91.9%-99.6%,硒回收率为93.5%-103.8%,相对标准偏差(RSD)砷小于2%,硒小于1%,检出限分别为0.035μg/L和0.038μg/L.     

微波消解-氢化物原子荧光光谱法测定油菜籽中的砷和汞

用用微波消解法处理富含油脂的油菜籽样品,氢化物原子荧光光谱法（HG-AFS）测定其中的砷和汞。砷在1—16μg/L范围内,有良好的相关性,相关系数r=0.9992;汞在0.1—1.6μg/L范围内,有良好的相关性,相关系数r=0.9994;砷和汞检出限分别为3.0μg/kg和1.6μg/kg;砷和汞测定的相对标准偏差RSD分别为9.8%、10%。用标准物质桃叶（GBW08501）验证方法准确性,结果令人满意。     

氢化物发生-原子吸收光谱法测定卷烟辅料中汞

研究了氢化物发生-原子吸收光谱法测定卷烟辅料中汞的方法,样品采用HNO3H2O2微波消解,然后以硼氢化钠为还原剂,用氢化物发生-原子吸收光谱法测定卷烟辅料中的汞.在最佳微波消化条件和测定条件下,线性范围为0.06-200μg/L,检出限为0.01μg/L,测定结果的相对标准偏差为2.2%-2.9%,回收率为97%-104%.结果令人满意.     

微波消解-氢化物发生原子荧光光谱法测定土壤中砷和硒

采用王水(1 1)作消解剂,以微波消解的方法处理土壤样品,氢化物发生-原子荧光光谱法测定土壤中砷、硒,设定了最佳的样品处理条件和仪器测定条件.利用加标回收试验,对分析方法进行了验证.砷、硒的检出限分别为0.94μg/L和0.15μg/L,测定土壤中砷、硒的回收率分别为90%-105%、89%-104%,RSD分别为2.2%-4.0%、1.9%-3.1%.     

双道原子荧光光谱法同时测定土壤中的砷和汞

建立了同时测定土壤中砷和汞的原子荧光光谱法。样品的相对标准偏差 As为 3.94 % ,Hg为 5 .0 0 % ,回收率在 90 %— 93%之间 ,对砷、汞的检出限分别为 0 .18μg/L和 0 .0 5 7μg/L。本法操作简便、快速、灵敏度高。     

微波消解-氢化物发生原子荧光法测定重油中的砷和汞

采用微波消解处理样品,以硫脲为预还原剂硼氢化钾为还原剂,氢化物发生原子荧光法测定重油中的砷和汞。采用微波消解方法进行样品处理,其结果表明,方法具有高效快速、试剂消耗量少、节能、环保等优点。考察了预还原剂硫脲和抗坏血酸对测定结果的影响。考察了酸度、还原剂浓度、基体效应、光电倍增管负高压、原子化器高度、灯电流和载气流量的影响,优化操作条件。测定砷和汞的线性范围分别为2~12μg/L和0.2~1.2μg/L,线性回归方程为If=a*c+b(c:μg/L),相关系数分别为0.9998和0.9981,砷和汞的检出限分别为0.009μg/L和0.007μg/L,对7个样品进行回收实验,砷、汞的回收率分别为90%~109%、92%~105%准确度较高;11次测定的标准偏差小于5%,精密度较好。本方法用于重油中砷和汞分析,可满足科研和生产需要。     

双道原子荧光光谱法同时测定农产品中的砷和汞

研究了湿法消解,双道原子荧光光度计同时测定农产品中的砷和汞,优化了检测条件和消解步骤,为在日常工作中,检测大量样品提供了快捷、简单、准确、灵敏和重现性好的方法。砷、汞检出限分别为:0.053μg/L、0.0136μg/L。针对一般化验室的仪器配置,采用简便的湿化消解方法,样品砷和汞加标回收率分别为96.8%—101.2%和96%—97.5%,对国家标准物质茶叶、牛肝等进行检测,精密度和准确度都符合要求。     

微波消解-氢化物原子荧光光谱法测定食品中的微量元素硒

采用HNO3-HClO4作为消解剂,在微波消解炉中消解样品,原子荧光光谱法测定食品中的微量元素硒.在最佳测定条件下测定元素硒的线性回归方程为:IF=95.4853C 9.2045,线性范围为0.5-10.0μg/L,相关系数r=0.9997.回收率2.0μg/L为95.65%-103.04%,6.0μg/L为95.61%-102.42%;相对标准偏差2.0μg/L为2.18%-3.55%,6.0μg/L为2.22%-3.98%.食品样品采用微波消解后,可用氢化物原子荧光光谱法测定其中的微量元素硒.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.