Effect of grain boundary sliding on the toughness of ultrafine grain structure steel: A molecular dynamics simulation study

Molecular dynamics simulations are carried out to investigate the mechanisms of low-temperature impact toughness of the ultrafine grain structure steel. The simulation results suggest that the sliding of the {001}/{110} type and {110}/{111} type grain boundary can improve the impact toughness. Then, the mechanism of grain boundary sliding is studied and it is found that the motion of dislocations along the grain boundary is the underlying cause of the grain boundary sliding. Finally, the sliding of the grain boundary is analyzed from the standpoint of the energy. We conclude that the measures which can increase the quantity of the {001}/{110} type and {110}/{111} type grain boundary and elongate the free gliding distance of dislocations along these grain boundaries will improve the low-temperature impact toughness of the ultrafine grain structure steel.     

不同晶面银纳米晶高温熔化的各向异性

采用嵌入原子势, 使用分子动力学方法, 模拟研究了银纳米晶高温弛豫过程中的热稳定性和熔化机制, 并引入均方位移和稳定寿命来分析它的结构和形状的演化过程. 结果表明: 对于沿相互垂直{110}, {211}和{111}面切割形成的近正方体截面纳米晶, 高温弛豫熔化存在明显的各向异性行为; (112) 面热稳定性最低, 最易熔化, 其次是(110) 面, 热稳定性最高的是(111) 面, 最难熔化; 三个不同晶面的最外层和次外层原子的稳定寿命极短, 且三个不同晶面之间相差很小, 没有明显差异; 对于具有相同晶面指数的晶面, 第三层及其以内的稳定寿命较长, 且依次微量增长, 但不同晶面第三层及其以内的寿命相差明显.     

bcc Fe中刃型位错的结构及能量学研究

基于位错理论，利用分子动力学方法建立了〈100〉{010}，〈100〉{011}，1/2〈111〉{011}和1/2〈111〉{112}刃型位错的芯结构，并计算了这四种刃型位错的形成能、位错芯能量和芯半径.计算结果表明：〈100〉{010}和〈100〉{011}刃型位错的形成能比1/2〈111〉{011}和1/2〈111〉{112}刃型位错的要高，这表明〈100〉刃型位错比1/2〈111〉刃型位错更难形成.而〈100〉{010}和〈100〉{011}刃型位错的芯半径比1/2〈111〉{011}和1/2〈111〉{112}刃型位错的小，这说明在1/2〈111〉刃型位错中位于奇异区的原子数多于〈100〉刃型位错，而这些原子要比完整晶体中的原子具有更大的活性.可见，1/2〈111〉刃型位错比〈100〉刃型位错更易运动，且〈100〉刃型位错在bcc Fe中难以形成. 关键词： bcc Fe 刃型位错 分子动力学模拟     

Dislocations in Fe-3% Si alloy single crystals deformed at a higher rate

The method of etching dislocations is used to study the distribution of dislocations and twins in Fe-3% Si alloy single crystals prepared from the melt after plastic deformation with higher speed. The crystals are deformed by twinning in the 〈111〉 directions along the {112} planes and by slip in the 〈111〉 directions along the {110} planes. The results prove that the dislocations causing plastic deformation move in the {110} planes during both fast and slow deformation. The difference in the slip surfaces during fast and slow deformation is explained by the different number of cross slips per unit dislocation path.     

β—SiC外延层中晶体缺陷的观察

用腐蚀法研究了β-SiC外延层中的晶体缺陷。腐蚀剂为熔融氢氧化钾。三角形尖底蚀坑对应于位错。在β-SiC中的全位错为立方晶系的73°位错和60°位错。不同堆垛方式的β-siC生长层相遇时将形成{111}交界层错,其腐蚀图象为平行于<110>方向的直线。60°位错可分解为两个1/6<112>SchockLey不全位错,并夹着一片{111}层错构成扩展位错。三个1/6<110>压杆位错与三片{111}层错可构成层错锥体。正、反堆垛的β-SiC可形成尖晶石律双晶,双晶面为(111)。腐蚀法和X射线劳厄法证实了这种双晶的存在。 关键词：     

Electron Backscattered Diffraction of Transgranular Crack Propagation in Soft Steel

We consider the crack propagation in a soft steel sheet during the formation. The drawability is considered in relation with the structural anisotropy, the mechanical behaviour is related to both the grain morphology and the texture. The structure heterogeneity could lead to the apparition of micro-cracks. The results show the texture effect on the crack propagation and on the crack arrest in soft steel during the formation. The EBSD technique allows to show that the adjustment of the grain orientation from the initial main component {111}（112） towards the deformation orientation {111}（110） incites a trans-granular crack through a grain with initial {111}（112） orientation in a globally ductile material. It is the presence of grains with {111}（110） orientation which permits the closing of micro-cracks.     

Rh超薄膜在Mo(111)及W(111)上引起{110}小面再构的可能性

用第一性原理总能计算方法,计算了Mo和W表面吸附金属Rh薄膜前后[111],[110]方向的表面能.计算结果表明,清洁Mo和W的（111）面不会发生{111}小面再构,与实验观察一致,当Rh的覆盖厚度达到一物理单层后,Rh/Mo（111）仍不会形成{110}小面;面Rh/W（111）满足小面再构到{110}的热力学条件,在一定条件下可能形成{110}小面. 关键词：     

纯铜[0 1 1]倾侧型非共格∑3晶界结构稳定性分子动力学模拟研究

有研究表明, 非共格∑₃晶界的行为在中低层错能面心立方金属晶界 特征分布演化中发挥着重要作用. 为了掌握不同界面匹配的非共格∑₃晶界的特性, 本文利用分子动力学(MD)模拟方法首先研究了纯铜的[0 1 1]倾侧型 非共格∑₃晶界在700–1100 K温度范围内和常压下的结构稳定性. MD模拟采用原子间相互作用长程经验多体势, 步长为5×10^-15 s. 模拟结果表明: 所研究的五个非共格∑₃晶界, 其结构稳定性存在很大差异, 其一般规律是, 与(1 1 1)/(1 1 1)共格孪晶界之间的夹角(Φ角)越小, 晶界匹配值越大, 则非共格∑₃晶界越稳定; 反之亦然. Φ角最小的 (2 5 5)/(2 1 1)非共格∑₃晶界较稳定, 在退火过程中几乎不发生变化. 随着Φ角的增大, 非共格∑₃晶界不再稳定, 这类晶界会通过Miller指数较高一侧晶体每三层原子面合并为一层原子面 (或Miller指数较低一侧晶体每一层原子面分解为三层原子面)的机理 转变为亚稳的“台阶”状晶界, 台阶面部分地处于精确的能量极低 的{111}/{111}共格孪晶界上; 当提高温度退火时, 这种“台阶”状晶界最终会全部转变成稳定平直的{111}/{111}共格孪晶界. 关键词： 纯铜 ∑₃晶界')" href="#">非共格∑₃晶界 分子动力学模拟     

Effect of dislocations on the shape of islands during silicon growth on the oxidized Si(111) surface

The formation of dislocation-rich and dislocation-free silicon islands during growth in the absence of mechanical stresses has been studied by scanning tunneling microscopy. The rounded shape of islands obtained at growth temperatures of 400–500°C on the oxidized Si(111) surface is associated with the presence of dislocations within them. The transfer of atoms from the oxidized surface to the islands occurs due to the barrier of the potential energy at the SiO₂/Si boundary. The {111} and {311} facets dominate in the shape of the islands grown at 500–550°C. Their appearance indicates the absence of the threading dislocations in the islands and that the growth is limited by the stage of the nucleation of a new atomic layer.     

集中力作用下硅中位错结构

本文用化学侵蚀法研究了硅单晶样品在800—1000℃印压得到的位错“花结”。实验结果说明:印压产生的位错分布在{111}滑移面上;位错线的取向大部分是<110>或<112>方向。分析并观察到在压印下有两种位错环,一种是柏格斯矢量沿<110>方向并平行于(111)印压面;一种是柏格斯矢量沿<110>方向并与印压面相交。对位错环的结构进行了分析。     

单晶铜纳米线屈服机理的原子模拟研究

采用分子静力学方法模拟了〈100〉单晶铜纳米线的拉伸变形过程,研究了纳米线屈服的机理. 结果表明：1） 纳米线初始屈服通过部分位错随机激活的{111}〈112〉孪生实现,后继屈服通过{111}〈112〉部分位错滑移实现;2） 纳米线变形初期不同滑移面上的部分位错在两面交线处相遇形成压杆位错,变形后期部分位错在刚性边界处塞积,两者都阻碍位错滑移,引起一定的强化作用. 关键词： 纳米线 屈服 位错 分子静力学     

Growth and stability of carbon islands on platinum surfaces

Details of the growth of C(graphite) islands and their stability on Pt surfaces were studied by FEM, UHV-SEM and very high resolution scanning AES. Initial nucleation of the C occurs on dislocations in the curved high index surface areas. Above 1150 K these randomly distributed islands dissolve and face specific layers are formed on {110} which can extend along the 〈100〉 zones all the way to the {100} planes. The sequence of stability of graphite layers on Pt is: {110} > all other {hk0} on the 〈100〉 zone except {100} > {100} followed closely by {111}. Concerning this layer stability, epitaxial mismatch plays a subservient role to the dipole interaction between metal substrate and graphite layer.     

EBSD FEG-SEM, TEM and XRD techniques applied to grain study of a commercially pure 1200 aluminum subjected to equal-channel angular-pressing

Microstructural evolution due to equal-channel angular-pressing (ECAP) with increasingly severe deformation was investigated in a commercially pure 1200 aluminum alloy. A true strain of eight produced sub-micrometer scale grains and very fine subgrains in the grain interior. The deformation process was documented and described using field-emission (FEG) gun scanning and transmission electron microscopy techniques. After eight ECAP passes, the high-angle grain boundaries accounted for approximately 70% of all boundaries. The fine spacing resolution of FEG scanning electron microscopy allowed detailed grain and subgrain statistical evaluation in the deformed microstructure; transmission electron microscopic inspection afforded appreciation of the role of very low-angle misorientation boundaries in the microstructure-refining process. ECAP results were compared with those produced by cold rolling. The material's texture evolved in a decreasing trend of Cube {001}100 intensities in favor of Cube rotated toward the normal-to-pressing direction {001}120, while Goss {110}001 and {111}110, {111}112 directions slightly increased with strain.     

铂修饰的{001}面暴露的二氧化钛纳米片阵列的制备和光催化性能

采用有机溶剂热法在FTO衬底上制备{001}面暴露的单晶锐钛矿相TiO₂纳米片阵列,通过FESEM和XRD研究样品的形貌和晶体结构. 与水热法制备的纳米片阵列相比,有机溶剂热法制备的样品取向性更好. 采用光沉积方法在纳米片阵列上沉积Pt,所得到的Pt纳米颗粒粒径更为均匀,并且更容易沉积在{001}面上. 所负载的Pt 纳米颗粒增强了TiO₂纳米片的光吸收性能,同时大大减弱了光致发光强度. 在光催化性能测试中,具有最优负载量的样品催化性能提高了一倍. 与传统的Pt负载相比,{001}面的最优负载量显得相当小,这可能源于高活性{001}面的原子结构.     

Growth and desorption of indium epitaxial layers investigated by high field microscopy

Growth of indium single crystals on tungsten field emission tips was carried out by deposition of indium from vapour in ultra high vacuum, using substrate temperatures in the range of 293–420 K. Two different tungsten tips were used as the substrate: a perfect W single crystal in one case and a bi-crystal with a distinct grain boundary in the other. No influence of the grain boundary on the epitaxial growth was found. Two orientation relationships were observed mostly: {111}In ∥ {110}W with 〈110〉In ∥ 〈111〉W and {111}In ∥ {100}W with 〈110〉In ∥ 〈110〉W. In the first case the growth was initiated by the indium nucleus created on the ledges of the {110}W plane. A field strength of 0.9 V/Å was found for the evaporation field of indium. The field strength of the desorption of In-W interfacial layer atoms was found to be 4.4–5.2 V/Å. A mechanism of the growth of indium crystals has been proposed.     

Σ = 3, {112} Lateral Twin Boundaries in GaP

The structure of = 3, {112} lateral twin boundaries in polycrystalline GaP has been investigated by transmission electron microscopy. The orientation of the polar bonding along the lateral twin boundary was characterized by convergent-beam electron diffraction and found to be mirror symmetric across the {112} interface. Rigid-body lattice translations and grain boundary dislocations along the boundaries were also characterized. The direction of the translation state between adjacent twin-related grains was studied by the -fringe contrast technique. Models of the {112} interface in the GaP lattice are proposed and compared with the experimental observations.

---

= 3, {112} Lateral Twin Boundaries in GaP

     

Peierls-nabarro barrier and stress of a/2 〈111〉 edge dislocation in α-Fe

The Peierls-Nabarro barrier and stress of thea/2〈111〉 edge dislocation on {112} and {110} plane inα-Fe at O K is calculated within the Peierls-Nabarro model. The method proposed by Nabarro is used, however, the sine force law is replaced by more general force laws based on two central interionic potentials inα-Fe. The values of the Peierls-Nabarro stress corresponding to one of the chosen interionic potentials, 3·5×10^?4 μ and 1×10^?4 μ on {112} plane (in the twinning direction) and on {110} plane, respectively, seem to be good estimates of the stress necessary to move edge dislocations inα-Fe at O K.     

Anomalous 13 422 diffraction spots from {111} flat gold crystallites: (111) surface reconstruction and moiré fringes between the surface and the bulk

This paper describes very flat {111} gold crystallites grown on graphite. The diffraction patterns of such crystallites show the “usual” $\text{1}\text{3}$ 422 anomalous spots. It is shown that these spots are in fact split in such a way that each $\text{1}\text{3}$ 422 spot is surrounded by an hexagonal array of additional spots, aligned in the 〈110〉 directions. When seen by TEM, the crystallites show 〈112〉 periodic contrasts which are not normal moiré fringes or misfit dislocations between gold and graphite. An interpretation following Yagi et al. is proposed which connects these 2 kinds of anomalies: they should result from the surface superstructure 23 × 1 of clean (111) gold face, described very recently by Melle and Menzel.