Possibilities of C 1s XPS and N(E) C KVV Auger spectroscopy for identification of inherent peculiarities of diamond growth

The interaction of C-atoms and CH_n-radicals with uncleaned and argon cleaned silicon substrate and with diamond surface after H-treatment have been studied in situ by XPS and Auger spectroscopy. It was found the formation of a new chemical surface state of carbon atoms in the case of carbon atoms and radicals interaction with cleaned silicon. The same chemical state was revealed on the H-treated diamond surface. Graphite-like structure of carbon atoms was observed on the surface of unlearned silicon and H-treated diamond after interaction with carbon atoms and radicals. N(E) C KVV Auger spectrum for the new chemical state of carbon atoms significantly differs from typical spectra for sp²- and sp³-bonded carbon materials. The high energy part of this spectrum was interpreted under the hypothesis of sp³-bonded carbon atoms but with shifted fermi level position.     

CH基团与金刚石(111)面的碰撞反应及其对碳膜生长的影响

等离子体增强化学气相沉积技术中的碳膜选择性自组装机理是高性能碳膜制备过程中的挑战性基础课题.采用经典分子动力学方法,模拟了不同能量(1.625-65 eV)的CH基团在清洁金刚石和吸氢金刚石(111)面上的轰击行为,获得了吸附、反弹、反应等各类事件的发生概率,并据此探讨了含氢碳膜制备过程中CH基团的贡献.结果表明,随着入射能量的增加,CH基团对薄膜生长的贡献由单纯的吸附、反弹机理向反应、吸附混合机理转变,其中最主要的反应过程是释放一个或两个氢原子的反应,而释放氢分子的反应则很少发生.这些反应不仅使薄膜生长过程更均匀、薄膜表面更平整,还降低了薄膜的氢含量.生长机理的转变导致低能量条件下所成薄膜中的多数碳原子都包含一个氢原子作为配位原子,而高能量条件下的薄膜中的碳原子则很少有氢原子作为配位原子.另外,通过分析sp~3-C和sp~2-C数目的变化,研究了CH基团对金刚石基底的破坏作用.     

The Uniform Si-O Coating on Cotton Fibers by an Atmospheric Pressure Plasma Treatment

A uniform Si-O coating on cotton fabric was produced at atmospheric pressure by a plasma treatment. Before the plasma discharge, a pretreatment with hexamethyldisiloxane (HMDSO)-ethanol mixture solvents on the fabric was employed. The surface morphology and chemical structure of the plasma-treated fibers were analyzed by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analyses. The SEM results showed that a uniform, continuous film was formed on the cotton fiber surface. It was much rougher than the uncoated fiber. The FTIR results showed that the coatings contained most of the Si-O functional groups. These Si-O bonds, broken from the Si-O-Si functional groups by the plasma electron impact, had connected with the cellulose by chemical bonds of Si-O-Cellulose. XRD patterns revealed the existence of a crystalline structure within the thin coating film. The UV-vis transmission of the cotton textile was greatly reduced by such coatings.     

Plasma-based introduction of monosort functional groups of different type and density onto polymer surfaces. Part 1: Behaviour of polymers exposed to oxygen plasma

Several approaches were investigated to produce monosort functionalized polymer surfaces with a high density and homogeneity of functional groups: (i) Plasma oxidation followed by wet-chemical reduction, (ii) formation of radicals and grafting on of functional group carrying molecules, (iii) plasma bromination followed by (iv) Williamson or Gabriel-like synthesis of spacer molecules, and (v) a pulsed plasma polymerization of functional groups bearing monomers or (vi) their copolymerisation with other comonomers. The formation of hydroxyl (OH), primary amino (NH₂), and carboxyl (COOH) groups was studied in detail. The oxygen plasma treatment (i) in a low-pressure non-isothermal glow discharge results in the formation of a wide variety of O functional groups, polymer degradation and crosslinking. Low power densities and short exposure times (0.1 to 2 s) are required to functionalize a surface while preserving the original polymer structure. Carbonate, ester, and aromatic groups are rapidly degraded by an oxygen plasma treatment leading to scissions of polymer backbones and loss in molecular weight. Also the formation of macrocycles and C=C bonds was observed in a region of around 4 nm in depth. The investigated polymers could be classified by their degradation behaviour on exposure to the oxygen plasma. In order to maximize the process selectivity for OH groups, the variety of oxygen functionalities formed by the oxygen plasma was wet-chemically reduced by diborane, vitride? (Na complex), and LiAlH₄. Typical yields were 9 to 14 OH groups per 100 carbon atoms. Plasma bromination (iii) (40 Br per 100 C atoms) of polymers, followed by grafting of spacer molecules (iv), has been proved to be a highly selective reaction. Another way to produce high densities of monosort functionalities was the pulsed plasma polymerization of functional group bearing monomers such as allylamine, allylalcohol or acrylic acid (v). The retention of chemical structure and functional groups during plasma polymerization was achieved by using low power densities and the pulsed plasma technique. The maximum yields were 30 OH, 18 NH₂, and 24 COOH groups per 100 C atoms. To vary the density of functional groups a chemical copolymerization with 'chain-extending' comonomers such as butadiene and ethylene was initiated in the pulsed plasma (vi). Additionally, the often-observed post-plasma oxidations of such layers initiated by reaction of trapped radicals with oxygen from the air were successfully suppressed by using NO gas as radical quencher.     

双价抗虫棉(Bt+CpTI)苗期重金属分配特性

随着转基因植物的推广应用,人们越来越关心其生态安全性。应用ICP-MS测定了转基因棉花及其亲本苗期各个器官中重金属Cr,As,Cd和Pb的含量。结果显示,棉花不同器官中重金属的含量差异较大,含量顺序分别是：根系>叶片>茎部。双价转基因(Bt+CpTI)抗虫棉叶片、茎部和根系中As、Cd都低于常规棉亲本;Cr在地上部两个器官低于对照,但是在根系累积增加;Pb在叶片和根系都高于对照,但是茎部下降。     

模板对异构体选择性生长的动力学控制作用与化学气相沉积金刚石的生长机理

阐述了模板的动力学控制作用对大尺度有序结构特别是亚稳相的生长，对自由能相差很小的异构体的选择生长所具有的重要作用.汲取现有金刚石生长理论的合理思想，以模板概念为基础给出了对化学气相沉积(CVD)过程的动力学热力学综合描述：1)碳原子在碳氢化合物中的化学势高于固相碳，气相碳氢化合物的碳原子有可能落到化学势较低的固态碳的各种异构体.2)气相碳通过表面反应实现向固相碳的转化.3)表面的模板作用是控制气相碳原子转换方式的主要动力学因素，不同的表面(石墨各种取向的表面及金刚石不同取向的表面)选择了落入其上的碳原子的结构方式及能量状态.4)因此,衬底的不同区域可发生几种不同的独立的表面反应过程,这些反应对应于不同表面的生长.5）而这些表面反应的方向性及速度受表面临域热力学因素的影响，反应的方向性决定了某种晶面是生长或刻蚀，在特定的温度、压强及各种气体分压下可以实现金刚石的生长和石墨的刻蚀.6)衬底局域晶格结构及键价结构和衬底表面气相的温度、压强及各种气体分压等热力学条件共同决定了成核的临界条件.7）与外界有能量和物质交换的等离子体系统，以及气相中发生的一系列化学反应，仅起到了维持某种固相表面生长所需要的非平衡热力学条件和化学条件的作用.金刚石和石墨表面具有的模板动力学控制作用，在特定热力学条件下主导自身外延层的生长方式；异质衬底的某些局域微观结构可以作为新相生长成核的局域模板；不同材料、不同的处理方法、及不同的化学环境下的衬底具有不同的局域微观结构，从而决定了多晶薄膜的取向优势. 关键词： 模板 异构体 选择性生长 金刚石薄膜     

Accumulation of hydrogen by silicon powders in HF inductive discharge plasma

The possibility of saturation with hydrogen of micro- and nanostructured silicon powders in electrodeless plasma is demonstrated. It is established that the hydrogen concentration in the bulk of the powder is determined by the size of its particles, the hydrogen pressure in the reaction chamber, and the HF power. The mechanism of plasma saturation with hydrogen is based on the chemical interaction of hydrogen atoms and active radicals with the surface of particles of the silicon powder, which is a surface with a distorted order of stacking of silicon atoms.     

Carbon nitride films by RF plasma assisted PLD: Spectroscopic and electronic analysis

Carbon nitride (CNx) thin films have been grown on Si 〈1 0 0〉 by 193 nm ArF ns pulsed laser ablation of a pure graphite target in a low pressure atmosphere of a RF generated N₂ plasma and compared with samples grown by PLD in pure nitrogen atmosphere. Composition, structure and bonding of the deposited materials have been evaluated by X-ray photoelectron spectroscopy (XPS), and Raman scattering. Significant chemical and micro-structural changes have been registered, associated to different nitrogen incorporation in the two types of films analyzed. The intensity of the reactive activated species is, indeed, increased by the presence of the bias confined RF plasma, as compared to the bare nitrogen atmosphere, thus resulting in a different nitrogen uptake in the growing films. The process has been also investigated by some preliminary optical emission studies of the carbon plume expanding in the nitrogen atmosphere. Optical emission spectroscopy reveals the presence of many excited species like C⁺ ions, C atoms, C₂, N₂; and CN radicals, and N₂⁺ molecular ions, whose relative intensity appears to be increased in the presence of the RF plasma. The films were also characterised for electrical properties by the “four-probe-test method” determining sheet resistivity and correlating surface conductivity with chemical composition.     

CuPc/ITO结构的表面和界面电子态的XPS研究

覆盖有Indium tin oxide(ITO)膜的透明导电玻璃广泛地用作有机发光器件 (OLEDs)的空穴注入电极 ,但是ITO膜的功函数通常与空穴传输材料的最高被占据分子轨道 (HOMO)不匹配。铜酞菁 (CuPc)作为缓冲层可以提高空穴从ITO向空穴传输材料的注入效率。对CuPc ITO样品的XPS表面分析表明 ,在CuPc分子中 ,铜原子显 2价 ,通过配位键和氮原子相互作用。CuPc分子中有两类碳原子 :8个C原子与 2个N原子成键 ;其余 2 4个C原子具有芳香烃性质。N原子也处在两种化学环境中 :有 4个N原子只与 2个C原子形成CNC键 ;另外 4个N原子不仅与 2个C原子成键 ,还通过配位键与Cu原子成键。用氩离子束对样品表面进行了溅射剥蚀 ,当溅射时间分别为 2 ,5 ,10min时进行XPS采谱分析 ,结果表明 ,随着氩离子束溅射时间增长 ,C 1s,N 1s峰变弱 ,Cu 2p ,O 1s,In 3d,Sn 3d峰增强 ,C 1s,N 1s,O 1s,In 3d和Sn 3d峰都向高束缚能或低束缚能方向移动 ,但它们的情况却不相同。     

Surface morphology changes of poly(ethyleneterephthalate) fabrics induced by cold plasma treatments

Some selective cold plasma processing modify specific surface properties of textile polymeric materials such as their dyeability, wettability and hydrorepellence. To correlate the sample surface changes with the acquired surface properties allows one to obtain information on the chemical and physical processing involved in plasma treatment. In this work, atomic force microscopy (AFM) has been applied to investigate the morphological and topographical surface modifications induced by RF cold plasma processing of poly(ethyleneterephthalate) (PET) fabrics. Rms surface roughness and surface area of the samples are measured before and after the treatments. The morphology changes have been analysed as a function of the treatment time and air gas pressure. Measurements have been performed also using plasmas produced by different gases such as He, Ar, SF₆ and CF₄. The PET shows different behaviour with different gas plasmas. In the case of air, He and Ar gases the sample surface modifications seem to be mainly due to etching effects, while the fluorine atoms grafting probably is responsible for surface rearrangement process using SF₆ and CF₄ gases. As a consequence different surface properties are produced in the plasma treated samples. Article presented at the International Conference on the Frontiers of Plasma Physics and Technology, 9–14 December 2002, Bangalore, India.     

The friction property of super-hydrophobic cotton textiles

Two kinds of super-hydrophobic cotton textiles were prepared via dip-coating cotton textiles with nano-silica suspensions, and the cotton textiles exhibits high contact angle more than 160° and low sliding angle lower than 4°. A friction method was used to evaluate the durability of the as-prepared super-hydrophobic cotton textiles, the results shows that one of the as-prepared super-hydrophobic cottons exhibits better stability property against friction, and its contact angle remained higher than 150° and sliding angle remained lower than 15° after 1000 times friction. SEM analysis shows the reduction of hydrophobic property was resulted from the damage of surface structure during friction cycle.     

On the chemical erosion of a carbon first wall proposed for Tokamak devices for controlled nuclear fusion

Preliminary results on the chemical attack of several carbon materials by hydrogen plasma are presented and compared with the literature data on the reaction of hydrogen atoms with carbon in an afterglow. The chemical erosion of silicon carbide and of pyrolytical graphite should not be dangerous for the ignition of fusion assuming that the reaction probability of hydrogen atoms with the particular material would not be increased due to radiation damage of the surface.     

Kinetic model of thin film growth by vapor deposition

A phenomenological kinetic model is proposed for describing the production of a thin film containing two components, A and B, by chemical and physical vapor deposition. The film was created by the “site-to-site” deposition of components A and B. The equations for the densities of components A and B in the surface layers were formed, and analytical and numerical solutions were obtained. The model includes the probabilities of different elementary processes for the interaction of gas phase components (molecules, radicals, atoms and ions) with those of A and B on the film surface. The deposition and erosion rates, the surface and volume densities of components A and B and the relative volume of micro-cavities inside the film were calculated as a function of the probabilities for the elementary processes of gas (plasma)-surface interactions. The experimental characteristics of a-Si: H thin films prepared by SiH₄ plasma deposition and those of carbon nitride thin films deposited from r.f. — magnetron sputtering and ion beam-assisted processes are compared with model calculations.     

电化学刻蚀法制备LaB6场发射微尖锥阵列

采用电化学刻蚀方法,成功制备出单尖的六硼化镧、钼、钨及钨铼合金场发射冷阴极尖锥,并对这几种场发射单尖锥阴极的电子发射性能进行了测试比较.结果表明,LaB₆作为场发射阴极,具有良好的发射性能和稳定性.在〈111〉面单晶LaB₆基片上,用PECVD法沉积非晶硅作掩膜,制备出具有一定高度的LaB₆微尖锥场发射阵列,结果发现,LaB₆基底较为平整,尖锥阵列呈现出各向异性.该结论对LaB₆材料在场发射阴极方面的进一步研究具有重要的指导意义.     

光谱诊断冷等离子体作用下甲烷转化机理的初步研究(英文)

冷等离子体是甲烷无氧活化制C2烃较为有效的技术手段之一,由于等离子体反应体系的复杂性,甲烷无氧活化制C2烃反应机理及过程尚不十分清楚。本文采用发射光谱原位诊断技术对冷等离子体作用下甲烷无氧活化制C2烃反应中若干激发态物种进行诊断研究,在250nm～670nm波长范围内检测到下列激发态物种:CH、C和C2。依据激发态物种检测结果、气相色谱反应产物分析结果及等离子体特性,推断了等离子体作用下甲烷无氧活化制C2烃的自由基反应历程。     

氦气对MPCVD沉积金刚石的影响

为了确定添加氦气对微波等离子体化学气相沉积(MPCVD)金刚石膜的影响,采用发射光谱法(OES)在线诊断了CH₄-H₂-He等离子体的发射光谱特性,研究了He对等离子体内基团空间分布的影响;并利用扫描电子显微镜(SEM)和拉曼(Raman)光谱对不同He体积分数下沉积出的金刚石膜进行了表征。结果表明：随着He体积分数的增加,等离子体内H_α, H_β, H_γ, CH和C₂基团的谱线强度均呈上升趋势,其中H_α基团的谱线强度增加最大。光谱空间诊断发现He的加入导致等离子体中各基团的空间分布均匀性变差,造成沉积出的金刚石膜厚度极不均匀。沉积速率测试表明,He的加入导致碳源基团相对浓度增加,有利于提高薄膜的沉积速率,当He体积分数由0 vol.%增加至4.7 vol.%时,沉积速率提高了24%。SEM测试结果表明,随着He体积分数的增加,金刚石膜表面形貌由(111)晶面取向向晶面取向混杂转变,孪晶生长明显。高He(4.7 vol.%)体积分数下由于C₂基团的相对浓度较高,导致二次形核密度增加。此外,由于基片台受到等离子体的刻蚀和溅射作用,导致薄膜沉积过程中引入了金属杂质原子。二次形核和杂质原子的存在使得孪晶大量的产生,薄膜呈现出压应力。     

Optimum Plasma Surface Treatment of Luffa Fibers

Luffa fiber is a renewable resource material with low cost and that contributes to a healthier ecosystem by its biodegradability. Its natural structure can be considered as a naturally occurring composite consisting mainly of cellulose fibrils imbedded in a lignin matrix. Surface pretreatment is necessary to maximize their potential use. In this work, plasma treatment at atmospheric pressure was carried out on the raw luffa fibers. The orthogonal method was used to optimize the plasma treatment condition. The optimal conditions were obtained at a discharge time of 10 s, power of 110 W, and electrode distance of 6 mm for the system used. The surface characterization of untreated and pretreated luffa fibers was investigated by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and thermogravimetric (TGA) analysis. The results showed that plasma treatment did not cause significant harm to the fiber integrity and the inner cellulose fibrils were exposed from the lignin matrix. Plasma-treated luffa fibers also showed a slightly better thermal stability than the untreated fibers. Compared with chemical pretreatment, plasma treatment had a significantly shorter duration, no consumption of solvent, and improved the cellulose contents.     

超光滑表面加工方法的新进展

通过回顾超光滑表面加工技术的发展历程,对多种具有代表性的超光滑表面加工方法的原理和应用作了简单阐述,并重点提出和介绍了一种大气等离子体抛光方法。该方法实现了利用常压等离子体激发化学反应来完成超光滑表面的无损伤抛光加工,并首次引入电容耦合式炬型等离子体源,为高质量光学表面的加工提供了一条新的途径。试验结果表明,在针对单晶硅的加工过程中实现了1μm/min的加工速率和Ra 0.6nm的表面粗糙度。     

A study on the antimicrobial efficacy of RF oxygen plasma and neem extract treated cotton fabrics

The paper deals with a thorough investigation on the antimicrobial activity of RF oxygen plasma and Azadirachtin (neem extract) treated cotton fabric. The hydrophilicity of cotton fabric was found to improve when treated with RF oxygen plasma. The process parameters such as electrode gap, time of exposure and oxygen pressure have been varied to study their effect on improving the hydrophilicity of the cotton fabric. The static immersion test has been carried out to assess the hydrophilicity of the oxygen plasma treated samples and the process parameters were optimized based on these test results. The formation of carbonyl group during surface modification in the plasma treated sample was analysed using FTIR studies. The surface morphology has been studied using SEM micrographs.The antimicrobial activity was imparted to the RF oxygen plasma treated samples using methanolic extract of neem leaves containing Azadirachtin. The antimicrobial activity of these samples has been analysed and compared with the activity of the cotton fabric treated with neem extract alone. The investigation reveals that the surface modification due to RF oxygen plasma was found to increase the hydrophilicity and hence the antimicrobial activity of the cotton fabric when treated with Azadirachtin.     

Spectroscopic measurements of excited particles in a N2 gas RF plasma-assisted carbon laser ablation

In this work, we investigated a carbon plasma plume produced by laser ablation of a graphite target in a nitrogen gas environment. The spatial distributions of C and N atoms were measured by time-resolved absorption spectroscopy. The spatial distributions of the relative densities of CN radicals, C₂, and C₃ molecules were measured using time-resolved emission spectroscopy. We determined that nitrogen gas produced an increase in carbon atom and molecule densities in the ablation plume. It was observed that the addition of RF plasma to the plume increased the CN radicals and C atom densities, and decreased the C₂ and C₃ molecule densities. The RF plasma changed the evolution of various fractional species of C, N, CN, C₂, and C₃ in the ablation plume. The chemical reactions with and without RF plasma were explained using the evolution and density of the fractional species of C, N, CN, C₂, and C₃in the plume. PACS 52.38.Mf; 42.62.Fi; 33.20.-t; 81.05.Uw