介孔二氧化钛光催化降解乙醛及其影响因素

"应用溶剂蒸发自组装的方法合成了具有蠕虫状孔道的介孔二氧化钛粉末和薄膜．考察了不同焙烧温度对材料介孔结构和光催化性能的影响．乙醛光催化降解实验用来表征不同焙烧温度下介孔材料的光催化性能．结果表明实验中合成的介孔二氧化钛材料的光催化活性明显高于颗粒二氧化钛(Degussa P25)．其中400 oC焙烧的样品具有平均孔径为6.0 nm的窄的孔径分布和117 m2/g的大的比表面积．通过对光催化活性结果的分析,发现介孔二氧化钛的活性主要受其比表面积和结晶性的共同影响．对介孔二氧化钛薄膜材料进行了同样的光催化表     

纳米结构锌及锌氧化物薄膜对甲基橙的降解作用研

采用磁控溅射方法制备了纳米金属锌薄膜,结合后续的空气退火处理制备了纳米锌氧化物薄膜. 金属锌薄膜对甲基橙的还原降解以及锌氧化物薄膜对甲基橙的光催化降解过程都可以用一级反应动力学方程来描述. 甲基橙溶液在金属锌膜的还原降解下具有最快的褪色速率,但矿化不完全：在紫外光波段出现的额外吸收峰表明生成了芳香族中间产物. 完全氧化的氧化锌薄膜对甲基橙的光催化降解速率仅为金属锌膜还原降解速率的1/4左右,没有出现芳香族中间产物. 另外实验发现部分氧化的锌氧化物薄膜对甲基橙的光催化降解速率明显高于完全氧化的氧化锌薄膜,光催化活性的提高可能由于部分氧化薄膜中同时存在的金属锌及氧化锌相之间的协同效应.     

三维有序二氧化锰大孔材料的模板技术合成及表征

以单分散SiO2 胶态晶体球形成的三维有序结构为模板 ,利用胶体晶模板技术合成了三维长程有序的二氧化锰大孔材料 .通过X射线粉末衍射 (XRD)和扫描电子显微镜 (SEM)对产物进行了表征 .其中XRD数据显示所得产物为纯四方相二氧化锰 .SEM结果表明 ,所合成的二氧化锰大孔材料孔大小均匀 ,空间排列高度有序 ,很好地复制了SiO2 胶态晶体球的自组装方式 .此外 ,对三维有序二氧化锰大孔材料的合成过程进行了分析 ,研究了前体填充次数对产物孔结构的完整性和有序性的影响 ,还发现产物孔径的收缩存在异常现象 .     

基于二氧化钛-介孔硅复合材料的光催化毒气过滤器

介绍了一种介孔硅与纳米二氧化钛的复合方法,制备了兼具高吸附性与高光催化活性的纳米二氧化钛-介孔硅复合材料.在此基础上,以365nm波长的紫外LED为光源、特制的半泄露聚合物光纤为导光介质制造了一种新型的光催化毒气过滤器.实验结果表明:当LED光功率为540mW,复合材料装填量为350g时,该过滤器对甲醛气体的吸附量大于3mg;当过滤器达吸附饱和后,输入甲醛气流量为2L/min、浓度为0.7mg/m~3,实时分解甲醛的速率达72μg/h,输出气体中甲醛浓度降至0.09mg/m~3,低于国家卫生标准中的室内甲醛浓度的安全阈值.纳米二氧化钛-介孔硅复合光催化剂的吸附特性为光催化分解提供了充分的反应时间,有利于提高光催化分解效率,可以长时间循环工作,有望用于家庭空气净化,甚至取代现有的活性炭过滤器,用在长效的防毒面具等装置中.     

硫和银共掺杂介孔TiO2的制备、表征及其对染料的光催化降解活性

以P123为模板,以钛酸四正丁酯、硝酸银和硫脲为原料采用模板法制备了一系列硫和银共掺杂介孔TiO₂光催化材料．利用SEM、XRD、BET和紫外-可见光谱等技术对其形貌、晶体结构及表面结构、光吸收特性等进行了表征．以甲基橙溶液的光催化降解为模型反应,考察了不同掺杂量的样品在紫外和可见光下的光催化性能．结果表明,用模板法制备的共掺杂介孔TiO₂光催化材料在紫外和可见光条件下较纯介孔TiO₂和单掺杂介孔TiO₂对甲基橙溶液具有更好的光催化降解效果, 且硫和银的掺杂量及样品焙烧温度显著影响该材料的催化性能．当硫掺杂量为2mol%和银掺杂量为1mol%,在500 oC 焙烧2 h所得光催化材料的催化性能最佳,4 h即可使甲基橙的降解率达98.8%,重复使用4次仍可使甲基橙的降解率保持在87.5%以上     

负载型二氧化钛光催化材料的制备及其光催化性能研究

以球形氧化铝为载体,采用溶胶-凝胶法和浸渍涂覆过程制备了负载型二氧化钛光催化材料。以扫描电子显微镜(SEM)和X-射线衍射仪(XRD)等手段对所合成的样品形貌及晶型进行了表征。结果表明,氧化铝载体经负载二氧化钛后,在球形氧化铝表面沉积了一层粒径为10~20nm的锐钛型二氧化钛纳米颗粒。通过能量色散X射线光谱(EDX)对氧化铝载体和所合成的样品进行进一步分析,表明样品中明显存在Ti元素。另外,提高氧化铝载体在二氧化钛溶胶中的浸渍次数能够有效提高二氧化钛的负载量。当浸渍次数增加到5次时,Ti元素的含量由3.8Wt.%提高至15.7Wt.%。另外,以亚甲基蓝为目标降解物,详细研究了不同浸渍次数获得的负载型二氧化钛催化材料的催化性能。结果表明:随着浸渍次数的增加,负载型二氧化钛催化材料的表面形貌不仅得到明显改善,而且显著提高了样品的光催化活性。当浸渍次数由1次提高至4次时,亚甲基蓝的降解率由40%上升至83.1%。然而,当二氧化钛负载量达到一定程度时,由于不断浸渍导致下层的二氧化钛受光照机会和光照强度减弱,导致其光催化活性提高缓慢。当浸渍次数提高至5次时,亚甲基蓝降解率仅为85.6%。所制备的负载型二氧化钛光催化材料重复使用5次,其光催化活性保持相对稳定。     

二氧化钛修饰的微结构聚合物光纤预制棒制备及其在光催化中应用的探索研究

首次用二氧化钛(TiO₂)纳米材料修饰的547孔微结构聚合物光纤(MPOF)二次预制棒作为阵列化微管式光催化反应器对亚甲基兰的光催化分解进行研究.将高光催化活性的P25型二氧化钛纳米粒子均匀分散在TiO₂溶胶中,对547孔微结构聚合物光纤孔洞内壁进行铺膜,得到了负载光催化剂的阵列化微管材料.该TiO₂MPOF有序复合的阵列化微管不仅对二氧化钛纳米粒子起到负载作用,还可以作为光波导介质(rolling-up薄膜波导,聚光、导光进入二氧化钛薄膜层)、污染物反应流体通道.以有机染料亚甲基兰为模拟污染物,研究了TiO₂负载量、亚甲基兰的初始浓度及溶液pH值等因素对光降解效果的影响.该反应器547个孔道的内表面用于负载光催化剂,不仅增加了固-液接触面积,也提高了光的吸收效率,从而提高了光催化效率.迄今为止,这种兼具导光、聚光、传质、负载功能于一体的光催化反应器还未见报道.     

光催化二氧化钛(TiO2)活性炭再生控制系统

对光催化二氧化钛(TiO2)活性炭进行了分析,利用光催化二氧化钛(TiO2)活性炭的再生机理,提出了光催化二氧化钛(TiO2)活性炭的制备方法及光催化二氧化钛(TiO2)活性炭再生控制系统的设计实现过程,论述了控制系统硬件原理,对TGS2600空气质量传感器电路、活性炭换层控制单元、再生用TL-D 15W/10紫外灯控制单元进行了描述和方案设计,对软件设计流程进行了讨论和说明; 在光催化二氧化钛(TiO2)活性炭再生控制系统,利用再生过程紫外灯光照强度连续监测及动态在线调整,结合程序计算反馈调整,运用碳层连续换层设计,使得 光催化二氧化钛(TiO2)活性炭的再生效率好,光催化二氧化钛(TiO2)活性炭再生控制系统对其它的类似设计提供了借鉴。     

光学相关论题 光化学

O644.1 2006043789介孔TiO2的材料合成及其在光催化领域的应用=Synthe-sis of mesoporous Ti O2andits applicationin photocatalysis[刊,中]/范晓星(南京大学环境材料与再生能源研究中心.江苏,南京(210093)) ,于涛…∥功能材料.—2006 ,37(1) .—6-9介孔Ti O2材料被证明在降解有害气体、有机染料等方面具有比传统颗粒Ti O2更高的光催化活性。本文综述了介孔Ti O2材料的合成方法及其在光催化领域的应用。图3表1参19(严寒)O644.1 2006043790可用于光催化研究的脉冲放电流光光源=Pulsed dis-charge streamer lamp-house available for p…     

H_3PW_(12)O_(40)/MCM-48的制备及其光催化降解农药(英文)

以介孔分子筛MCM-48为载体,采用水热法制备了负载磷钨酸H3PW12O40(HPW)的多金属氧酸盐催化剂HPW/MCM-48。利用傅里叶变换红外光谱(FT-IR)、小角度X射线粉末衍射(XRD)、氮气吸附检测和高分辨透射电子显微镜(HRTEM)对其结构进行了表征,并以农药吡虫啉和百草枯为对象,考察了所制备的HPW/MCM-48的光催化降解活性。结果表明,采用水热法制备的催化剂保持了MCM-48的介孔分子筛结构和HPW的Keggin结构,比表面积783.35m2·g-1,孔体积1.46cm3·g-1,平均孔径2.76nm,相比于母体HPW,HPW/MCM-48的比表面积大大增加;在365nm紫外光下反应14h后,20mg剂量HPW/MCM-48催化剂能使50mL,10mg·L-1吡虫啉和百草枯的降解率分别达57.38%和63.79%,而HPW对两种农药的降解率在25%左右,空白组降解率均低于5%,说明负载后HPW对两农药的降解活性显著增强。动力学考察表明,HPW/MCM-48对农药降解过程符合一级动力学方程,对吡虫啉和百草枯这两种农药的降解速率常数Ka分别为0.089和0.117h,半衰期t1/2为7.8和5.9h。     

Photocatalytic activity enhancement of TiO2 films by micro and nano-structured surface modification

Titanium oxide thin films were deposited by spin coating using a precursor solution of titanium oxide (IV) acetylacetonate. To increase the contact surface area of the films, TiO₂ microspheres were added to the surface of the films. These spheres were 2 μm in diameter and formed agglomerates on the surface. They did not spread uniformly across the substrate, creating different roughnesses and morphologies along the surface of films. Photocatalytic properties of the samples were tested by the degradation of a methyl orange solution. The degradation performance was compared between plain films, films with microspheres and films covered with commercial TiO₂ P25 powder. The results indicate that the samples that were surface modified with TiO₂ microspheres present a photodegradation reaction rate 62 times higher than that obtained for plain TiO₂ films. The rate of reaction of the samples covered with P25 was 2 times greater than that obtained for the samples with microspheres, but the adhesion to the film was better in the case of microspheres. Moreover, samples with microspheres could be reused several times maintaining the same structural and photocatalytic properties.     

Enhanced photocatalytic degradation of Safranin-O by heterogeneous nanoparticles for environmental applications

Nanostructure titanium dioxide (TiO₂) has been synthesized by hydrolysis of titanium tetrachloride in aqueous solution and Ag-TiO₂ nanoparticles were synthesized by photoreduction method. The resulting materials were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier-transform infrared (FT-IR) and UV-vis absorption spectroscopy. The experimental results showed that the sizes of the synthesized TiO₂ and Ag-TiO₂ particles are in the range of 1.9-3.2 nm and 2-10 nm, respectively. Moreover, Ag-TiO₂ nanoparticles exhibit enhanced photocatalytic activity on photodegradation of Safranin-O (SO) dye as compared to pure TiO₂. The positive effect of silver on the photocatalytic activity of TiO₂ may be explained by its ability to trap electrons. This process reduces the recombination of light generated electron-hole pairs at TiO₂ surface and therefore enhances the photocatalytic activity of the synthesized TiO₂ nanoparticles. The effects of initial dye and nanoparticle concentrations on the photocatalytic activity have been studied and the results demonstrate that the dye photodegradation follows pseudo-first-order kinetics. The observed maximum degradation efficiency of SO is about 60% for TiO₂ and 96% for Ag-TiO₂.     

Surface-modification of indium tin oxide nanoparticles with titanium dioxide by a nonaqueous process and its photocatalytic properties

Indium tin oxide nanoparticles prepared by co-precipitation were re-dispersed in benzyl alcohol and modified successfully with titanium dioxide using titanium tetrachloride as precursor. The morphologies and the re-dispersing processes of both the initial and modified indium tin oxide nanoparticles were investigated, respectively. The photocatalytic properties of the modified nanoparticles were compared with commercial P25 photocatalyst. It was found that (i) the average diameter of the initial indium tin oxide nanoparticles was 10.7 nm and that of the surface-modified nanoparticles was 14.5 nm; (ii) the optimal ultrasonication time was 10.0 min and 8.0 min for the initial and surface-modified ITO nanoparticles, respectively; (iii) the modified particles possessed a higher photocatalytic activity than commercial P25 photocatalyst in the photodegradation of rhodamine B in aqueous medium at pH 5.00; (iv) the pH of the medium markedly influences the photodegradation efficiency.     

Mechanism of O2-accelerated sonolysis of bisphenol A

The effects of dissolved gases on the sonochemical degradation of bisphenol A (BPA) were studied at a frequency of 500 kHz. BPA degradation rate increased in the order O(2)>Ar>air>N(2). The rate constant for oxygen (2.6 h(-1)) was approximately two fold higher than that for argon (1.2 h(-1)). A primary intermediate (2,3-dihydro-2-methylbenzofuran), a typical intermediate of BPA formed during attack by OH radicals, was detected only in the presence of oxygen, revealing that a different reaction path was responsible for the enhancement of decomposition.     

不同干燥法制备纳米TiO2光催化剂的光谱研究

本文分别用常态、超临界乙醇和超临界CO2干燥法干燥钛酸正丁酯的醇凝胶，制备纳米TiO2光催化剂。应用XRD，FTIR，FT－Raman和Fluorescent spectrum(FS)等光谱技术对催化剂进行了表征。以光催化降解罗丹明B为模型反应，比较所得样品光催化活性。实验结果表明，不同干燥方法对催化剂的晶相结构、半导体能带结构、光吸收性能、表面性质及光催化活性均产生显著的影响，用超临界CO2干燥法制备的TiO2光催化剂具有较好的光催化活性。     

Low temperature deposition and characterization of TiO2 photocatalytic film through cold spray

Cold spray was employed as a novel low temperature approach to deposit titanium dioxide (TiO₂) photocatalytic film. The film microstructure was characterized using X-ray diffraction and scanning electron microscopy. The photocatalytic performance was examined through acetaldehyde degradation under ultraviolet illumination. Results showed that TiO₂ film was successfully deposited on substrate surface through cold spray. The film thickness reached up to 15 μm. The film presented a rough surface and porous structure. Owing to the low temperature of spray powder, no phase and particle size changes occurred to TiO₂ during deposition. It was found that the cold-sprayed TiO₂ film was active for photodegradation of acetaldehyde.     

Enhanced photocatalytic activity of silver metallized TiO2 particles in the degradation of an azo dye methyl orange: Characterization and activity at different pH values

The photocatalytic activity of silver deposited Degussa P25 titanium dioxide (Ag-DP25) in the photodegradation of methyl orange (MO) was investigated. The photocatalysts were characterized using PXRD, SEM, EDX, FTIR and UV-vis spectrophotometer. The obtained results show that the silver (Ag⁰) deposited TiO₂ exhibited visible light plasmon absorption band. The degradation experiment reveals that the catalytic property of Ag-DP25 in the degradation of MO is more efficient than that of commercially available Degussa P25 TiO₂ (DP25) samples. The improvement of Ag-DP25 catalyst efficiency strongly depends on the content of silver (Ag) deposits. The present study shows that the degradation process is dominated by Ag-TiO₂ photocatalytic system, complying with pseudo-first order rate law. The higher rate of photodegradation observed on Ag-DP25 at pH 6.6 can be correlated to the ratios of the concentrations of the ionized to the neutral dye molecules and also to the higher concentration of hydroxylated surface, which are able to effectively scavenge photogenerated valence band holes. Accumulation of the holes in the semiconductor particles increases the probability of formation of excited oxygen atom which is a reactive species readily oxidizing the organic dye molecule. The reduction of pH during the course of the reaction is attributed to the complete mineralization of the dye.     

水热法制备二氧化钛纳米管-石墨烯复合光催化剂及其光催化性能

采用水热法制备了二氧化钛纳米管-石墨烯的复合光催化剂。利用X射线衍射仪、扫描电镜、透射电镜和拉曼光谱仪对复合材料进行了表征与分析,并对其光催化性能进行了测试。结果显示,同纯二氧化钛纳米管相比,二氧化钛纳米管-石墨烯的光催化性能较高。石墨烯与二氧化钛纳米管复合,充当电子受体,载流子迁移率得到提高,从而提升了光催化性能。     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Immobilized TiO<Subscript>2</Subscript> nanoparticles produced by flame spray for photocatalytic water remediation

Anatase/rutile mixed-phase titanium dioxide (TiO₂) photocatalysts in the form of nanostructured powders with different primary particle size, specific surface area, and rutile content were produced from the gas-phase by flame spray pyrolysis (FSP) starting from an organic solution containing titanium (IV) isopropoxide as Ti precursor. Flame spray-produced TiO₂ powders were characterized by means of X-ray diffraction, Raman spectroscopy, and BET measurements. As-prepared powders were mainly composed of anatase crystallites with size ranging from 7 to 15 nm according to the synthesis conditions. TiO₂ powders were embedded in a multilayered fluoropolymeric matrix to immobilize the nanoparticles into freestanding photocatalytic membranes. The photocatalytic activity of the TiO₂-embedded membranes toward the abatement of hydrosoluble organic pollutants was evaluated employing the photodegradation of rhodamine B in aqueous solution as test reaction. The photoabatement rate of best performing membranes significantly overcomes that of membranes produced by the same method and incorporating commercial P25-TiO₂.