1137 nm长波掺镱光纤激光器的出光实验

分别使用976 nm半导体激光器和1040 nm光纤激光器作为泵浦源,实现了1137 nm长波光纤激光器的出光,输出功率均超过百mW。激光器采用相同的线性腔结构,高反光栅和低反光栅的反射率分别为99.6%和39.7%,增益介质是一段8 m长的掺镱光纤,纤芯直径5 m。当976 nm半导体泵浦功率为912 mW时,1137 nm激光输出功率为182 mW,对应的斜率效率为28.5%;当1040 nm激光功率为1.59 W时,输出的1137 nm激光功率为278 mW,斜率效率约为25%。在此基础上对两种泵浦方式进行了对比分析。     

Second-harmonic generation of light at 544 and 272 nm from an ytterbium-doped distributed-feedback fiber laser

We report external cavity second-harmonic generation of light at 544 and 272 nm based on an ytterbium-doped distributed-feedback fiber laser. The nonlinear crystal used to generate light at 544 nm is LiNbO3, and the maximum output of the cavity is 845 mW, corresponding to a conversion efficiency of 55%. In a second frequency-doubling step, using a beta-BaBa2O4 crystal, we generate up to 115 mW of light at 272 nm with a conversion efficiency of 14%.     

Stable single-longitudinal-mode fiber laser using PM FBG F-P etalon and PM fiber saturable absorber

we present a stable and high efficiency single-longitudinal-mode (SLM) fiber ring laser by using polarization-maintaining fiber Bragg grating Fabry-Perot (PM FBG F-P) etalon combining PM fiber saturable absorber. The PM FBG F-P etalon, which is directly fabricated in hydrogen-loaded PM fiber, is used as reflector and mode-selecting component to reduce the longitudinal-mode density greatly. Meanwhile, a segment un-pumped PM Er³⁺-doped fiber (EDF) serves as saturable absorber to suppress mode hopping and ensure the stable SLM operation. Stable SLM laser output at 1550.4 nm with linewidth of 2.0 kHz is observed. Laser output power is 43.7 mW for a pump power of 148 mW, optical-optical efficiency is 29.5% and signal-to-noise ratio (SNR) is larger than 55 dB.     

Continuous-wave fiber optical parametric oscillator

We report continuous-wave operation of singly resonant fiber optical parametric oscillators. In a cavity formed by 100 m of highly nonlinear fiber and two fiber Bragg gratings, the pump power threshold was 240 mW; the output wavelength could be tuned over 80 nm by tuning of the pump. We also obtained an internal conversion efficiency of 30%, compared with the maximum theoretical value of 50%, by use of a 1-km-long cavity.     

光纤复合环形腔单模激光器的研究

单模光纤激光器在光通讯和光传感中具有广阔的应用前景。分析了复合腔光纤激光器的构成及单模的实现特点,提出了一种新颖的光纤复合环形腔激光器结构,并对其进行了实验研究。该激光器使用了波长为980nm的半导体激光器作为泵浦源。三个腔长均为2m,彼此之间的腔长差为1～2mm的光纤环形滤波器与主谐振腔构成复合腔。此激光器在波长为1562nm处得到了线宽小于0.1nm的单模激光输出,输出的光功率可达到1mW。该激光器的阈值为5mW,斜率效率为4%。     

Linear cavity fiber laser with 100 nm wavelength tuning range

We report a 100 nm widely tunable double-clad Ytterbium doped fiber laser. The fiber laser has a linear cavity configuration, where the feedback is provided by a Sagnac fiber mirror on one side, and an external bulk grating on the other side. On the bulk grating side, the fiber has a balled curved-core-termination that suppress backreflection by roughly 50 dB, and does not affect the pump coupling efficiency. The tuning range goes from 1055 nm through 1155 nm, with a maximum output power of 360 mW at 1080 nm, and 0.3 nm linewidth.     

High-efficiency Q-switched erbium fiber laser using a Bragg grating-based modulator

In this work we analyze the behavior of an erbium-doped fiber laser which is based on a simple scheme. Excitation of the active medium is performed in the 980 nm pump band with a CW semiconductor laser source. Two fiber Bragg gratings acting as mirrors of the Fabry–Perot laser cavity were used. One of these gratings was mounted over a piezoelectric (PZT) element. By applying voltage pulses to the piezoelectric, the laser cavity was temporally modulated and Q-switched laser pulses up to 530 mW peak powers at 3 kHz were obtained. Typical laser emission of 2–3 μs temporal widths and 0.1 nm of optical bandwidth have been achieved when the system was operated at 18.5 kHz repetition rates. Different behaviors were observed depending on the pumping level of the active medium and on the amplitude and frequency of the signal applied on the PZT. Q-switched laser output, in the erbium spectral gain region, with high laser efficiency of energy conversion was generated. Pumping at 76 mW and operating the laser at 18.5 kHz, an efficiency of 26% was obtained.     

Excited-state absorption and 1064-nm end-pumped laser emission of Nd:YVO4 single-crystal fiber grown by laser-heated pedestal growth

We present an investigation of the excited-state absorption and laser emission of a 1.0-at. %-Nd3+-doped YVO4 single-crystal fiber grown by the low-cost and versatile laser-heated pedestal growth technique. Efficient laser emission at 1064 nm was achieved when the fiber was pumped, in an end-pump cavity, by a Ti:sapphire laser at 808 nm. A continuous-wave threshold of 10 mW was observed with an efficiency of 42% with respect to the absorbed pump power and the maximum output power of 200 mW. These results are excellent when compared with those of a commercial bulk crystal adapted to the same cavity (48% efficiency, 250-mW maximum output power). Thus the fibers are characterized as strong candidates for the construction of compact lasers that can also be pumped by low-cost diode lasers.     

Single-frequency thulium-doped distributed-feedback fiber laser

We have successfully demonstrated a single-frequency distributed-feedback (DFB) thulium-doped silica fiber laser emitting at a wavelength of 1735 nm. The laser cavity is less than 5 cm long and is formed by intracore UV-written Bragg gratings with a phase shift. The laser is pumped at 790 nm from a Ti:sapphire laser and has a threshold pump power of 59 mW. The laser has a maximum output power of 1 mW in a single-frequency, single-polarization radiation mode and is tunable over a few nanometers. To the best of the authors' knowledge, this is the first report of a single-frequency DFB fiber laser that uses thulium as the amplifying medium. The lasing wavelength is the longest demonstrated with DFB fiber lasers and yet is among the shortest obtained for thulium-doped silica fiber lasers.     

Short Tm3+-doped fiber lasers with watt-level output near 2 μm

High-power operation of diode-pumped fiber lasers at wavelength near 2μm are demonstrated with short length of heavily Tm3 -doped silica glass fibers. With 7-cm long fiber, a laser at near 2 μm is obtained with the threshold of 135 mW, maximum output power of 1.09 W, and slope efficiency of 9.6% with respect to the launched power from a laser diode at 790 nm. The output stability of this fiber laser is within 5%.The dependence of the performance of fiber lasers on the operation temperature and cavity configuration parameters is also investigated.     

Nd-doped phosphate glass microstructured optical fiber laser

We experimentally demonstrated a single-mode laser at 1056 nm with Nd-doped phosphate glass microstructured optical fiber (MOF), which was fabricated with conventional stack-and-draw method. The laser action was observed from a Fabry-Perot cavity formed by placing two dichroic mirrors of ∼100 and 85% reflectivity, to the two end facets of MOF. Pumped by CW laser diodes (LDs) at 808 nm, the MOF laser yielded a maximum output power of 8.5 mW and a slope efficiency of 2%.     

光纤光栅F-P标准具选模单频环形腔光纤激光器

 讨论了光纤光栅法布里-珀罗(F-P)标准具选模光纤激光器的单频运转原理，并研制了全光纤结构单频掺Er³⁺光纤环形激光器。实验中采用两个976 nm激光二极管双向泵浦作为泵浦源，高掺杂浓度掺Er³⁺光纤作为增益介质，以行波腔消除空间烧孔效应，利用光纤光栅F-P标准具窄带选模特性，当泵浦光功率为36 mW时，得到了稳定的单频激光输出。实验中使用了长5和3 m的掺杂光纤，在泵浦光功率为145 mW时输出功率分别为19和42 mW，光-光转换效率分别为13%和29%，斜率效率分别达到了16%和33%。输出谱线3 dB带宽0.01 nm，无跳模现象。     

同带抽运高效率光纤放大器

以光纤光栅为谐振腔搭建了波长为1020 nm的光纤激光器,并通过两级级联放大获得了590 mW的最大输出功率. 利用获得的波长为1020 nm的激光进行了波长为1064 nm种子光同带抽运放大,实验研究了不同增益光纤长度时放大器的输出功率和转换效率. 当增益光纤长度为8.5 m时,放大器最大输出功率为385 mW,斜率效率为81%. 进行了波长为976 nm的半导体激光器直接抽运波长为1064 nm种子光的实验. 在增益光纤长度最优时,其斜率效率为56.4%. 实验结果表明,同带抽运方式比传统抽运方式具有更高的转换效率. 研究结果可为波长为1020 nm的激光高功率放大和波长为1064 nm的光纤激光高功率同带抽运放大提供一定的参考. 关键词： 同带抽运 光纤放大器 斜率效率     

Effects of output coupler reflectivity on the performance of a linear cavity Brillouin/erbium fiber laser

The effect of output coupler reflectivity (or output coupling ratio) on the performance of a linear cavity Brillouin/erbium fiber laser (BEFL) is demonstrated. The operating wavelength, output laser power and number of channels vary with changes in the coupling ratio in the linear cavity system. The optimum BEFL operation is obtained with an output coupling of 40%, i.e., 60% of the laser power is allowed to oscillate in the cavity. A stable laser comb consisting of up to 40 channels with line spacings of approximately 0.09 nm are obtained at the Brillouin pump and 980 nm pump with powers of 2.5 mW and 100 mW, respectively. The linear cavity BEFL has the potential to be used in inexpensive wavelength division multiplexing system.      

Yb3+-doped double-clad fiber laser with all fiber cavity

A novel all fiber cavity Yb3+-doped double-clad fiber laser (DCFL) based on two double-clad fiber (DCF)Bragg grating is presented. The fiber Bragg gratings (FBGs) as the input and output mirrors have been formed in Yb3+-doped DCF with the phase-mask method, and their reflectivities are 99% and 22%,respectively. When the input pump power is 417 mW, the maximum output power is 144 mW with linewidth ＜0.1 nm at the wavelength of 1.057μm, over 40-dB signal-to-noise ratio (SNR), and 50.8% slope efficiency.     

Diode-pumped 1018-nm ytterbium-doped double-clad fiber laser

We report a 1 018-nm ytterbium-doped double-clad fiber laser pumped by 970-nm diode. A pair of fiber Bragg gratings with reflectivities of 99.9% and 9% at a center wavelength of 1 018.9 nm are employed as cavity mirrors. The ytterbium-doped double-clad fiber is a 2.6-m-long Liekki fiber. Laser output power of 7.5 W at 1 018 nm is obtained under the pump power of 59.2 W. The overall slope efficiency of the fiber laser is about 16%. This low slope efficiency is mainly due to the incomplete absorption of the pump power.     

Diode-pumped Pr(3+):KY(3)F(10) red laser

We report the first observation to our knowledge of room-temperature continuous-wave laser operation of a Pr(3+):KY(3)F(10) single crystal at 644.5 nm, pumped by a blue GaN laser diode emitting at 446 nm. With a 2.5% transmission output coupler and a nonoptimized optical cavity, an output power of 39 mW was obtained at 644.5 nm with a laser threshold of 125 mW and a differential slope efficiency of 23%.     

1018 nm短波长掺镱光纤激光高功率自组织相干合成

搭建了两台高功率、低量子损耗的1018 nm短波长掺镱光纤激光器,进行了全光纤结构下两路光纤激光器的相干合成实验。获得了功率为55 W、合成效率为90.2%的相干输出,这是当前严格单模1018 nm光纤激光器的最高功率水平。同时,验证了Michelson腔自组织相干合成技术能够实现光纤激光器的高功率单模输出。     

Three-level neodymium fiber laser incorporating photonic bandgap fiber

We report a neodymium fiber laser incorporating an all-solid photonic bandgap fiber to suppress the four-level laser transition 4F(3/2)-4I(11/2). We demonstrate lasing at 907 nm on the three-level transition 4F(3/2)-4I(9/2) when pumping at 808 nm. The maximum slope efficiency obtained was 32% with a threshold pump power of 70 mW.