The compatibilizing effect of epoxy resin (EP) on polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr) blends

A new method was used to prepare thermoplastic elastomers based on polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr) with improved mechanical properties. An epoxy resin (EP) was used as a compatibilizing agent. The effect of EP on mechanical properties, swelling percentage and morphological characteristics of the blends was investigated with different blend compositions. The results showed that the incorporation of EP has improved the tensile strength, Young's modulus and elongation at break of PP/NBRr-EP blends compared with PP/NBRr blends. The enhancement of tensile properties of PP/NBRr-EP blends is due to the better adhesion between the two phases with the incorporation of EP. This is quite evident by scanning electron microscopy of tensile fractured surfaces. PP/NBRr-EP blend exhibits lower stabilization torque and swelling percentage than PP/NBRr blends. The lower stabilization torque is an indication of better processing characteristics.     

Poly(4-methylpentene-1)/hydrogenated oligo (cyclopentadiene) blends: Miscibility,tensile stress–strain,and dynamic mechanical behaviors

This article discusses the influence of the oligomeric resin, hydrogenated oligo(cyclopentadiene) (HOCP), on the morphology, and thermal and tensile mechanical properties of its blends with isotactic poly(4-methylpentene-1) (P4MP1). The P4MP1 and HOCP are found not miscible in the melt state. P4MP1/HOCP blends after solidification contain three phases: the crystalline phase of P4MP1, an amorphous phase of P4MP1, and an amorphous phase of HOCP. From optical micrographs obtained at 150°C, it is found that the solidified blends show a morphology constituted by P4MP1 microspherulites and small HOCP domains homogeneously distributed in intraspherulitic regions. DSC and DMTA results show that the blends present two glass transition temperatures (T_g) equal to the T_gs of the pure components. The tensile mechanical properties have been investigated at 20, 60, and 120°C. At 20°C both the HOCP oligomer and the amorphous P4MP1 are glassy, and it is found that all the blends are brittle and the stress–strain curves have equal trends. At 60°C the HOCP oligomer is glassy, whereas the amorphous P4MP1 is rubbery. The tensile mechanical properties at 60°C are found to depend on blend composition. It is found that the Young's modulus, the stresses at yielding and break points slightly decrease with HOCP content in the blends and these results are related to the decrease of blend crystallinity. The decrease of the elongation at break is accounted for by the presence of glassy HOCP domains that act as defects in the P4MP1 matrix, hampering the drawing. At 120°C both the amorphous phases are rubbery. It is found decreases of Young's modulus, stresses at yielding and break points. These results have been related to the decrease of blend crystallinity and to the increase of the total rubbery amorphous phase. Moreover, it is found that the blends present elongations at break equal to that of pure P4MP1. This constancy is attributed to: (a) at 120°C the HOCP domains are rubbery and their presence seems not to disturb the drawing of the samples; (b) a sufficient number of the tie-molecules and entanglements of P4MP1 present in the blends. In fact, although the numbers of tie-molecules and entanglements decrease in the blends, increasing the HOCP oligomer, they seem to be enough to keep the material interlaced and avoid earlier rupture. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1269–1277, 1997     

Biodegradable stereocomplex materials of polylactide‐grafted dextran exhibiting soft and tough properties in dry and wet states

Water‐swellable biodegradable materials exhibiting mechanically tenacious and tough characters in the wet state were prepared by a simple blend of two enantiomeric polylactide‐grafted dextran copolymers (Dex‐g‐PLLA and Dex‐g‐PDLA). DSC and WAXD analyses demonstrated the formation of SC crystals in the copolymer blend films. SC blend films showed lamellar‐type microphase‐separated structures. When swollen with water, these blend films showed the same level of tensile strengths and Young's modulus as the films in the dry state. SC blend films degraded gradually over a month under physiological conditions with a degradation rate faster than the corresponding Dex‐g‐PLLA films. The SC‐forming enantiomeric mixture of polylactide‐grafted polysaccharides should be a good candidate for an implantable biocompatible material exhibiting favorable mechanical properties and degradation behavior. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

High density polyethylene/hydrogenated oligo(cyclopentadiene) blends: Phase structure,thermal and mechanical properties

The article discusses the influence of an oligomeric resin, hydrogenated oligo (cyclopentadiene) (HOCP), on the morphology and properties of its blends with high density polyethylene (HDPE). HDPE/HOCP blends after solidification contain three phases: the crystalline phase of HDPE and two amorphous phases, one rich in amorphous HDPE and the other in HOCP. DSC thermograms and the loss modulus behaviors show that the γ transition is influenced by HOCP molecules and, in addition to the α_c transition of HDPE, there is another transition that is attributed to the HOCP-rich phase. The hypothesis of the two amorphous phases is confirmed by the optical microscopy observations performed on isothermally crystallized blend films. © 1994 John Wiley & Sons, Inc.     

Thermal properties and structure of electrospun blends of PVDF with a fluorinated copolymer

We report the structure and thermal properties of blends comprising poly(vinylidene fluoride) (PVDF) and a random fluorinated copolymer (FCP) of poly(methyl methacrylate)‐random‐1H,1H,2H,2H‐perfluorodecyl methacrylate, promising membrane materials for oil–water separation. The roles of processing method and copolymer content on structure and properties were studied for fibrous membranes and films with varying compositions. Bead‐free, nonwoven fibrous membranes were obtained by electrospinning. Fiber diameters ranged from 0.4 to 1.9 μm, and thinner fibers were obtained for PVDF content >80%. As copolymer content increased, degree of crystallinity and onset of degradation for each blend decreased. Processing conditions have a greater impact on the crystallographic phase of PVDF than copolymer content. Fibers have polar beta phase; solution‐cast films contain gamma and beta phase; and melt crystallized films form alpha phase. Kwei's model was used to model the glass transition temperatures of the blends. Addition of FCP increases hydrophobicity of the electrospun membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 312–322     

Phase morphology and mechanical properties of iPP/SEP blends

The effects of the addition of diblock copolymer poly(styrene‐b‐ethylene‐co‐propylene) (SEP) to isotactic polypropylene (iPP) on the morphology and mechanical properties were investigated. Phase morphologies of iPP/SEP blends up to a 70/30 weight ratio, prepared in Brabender Plasticoder, were studied with optical microscopy, scanning electron microscopy, transmission electron microscopy, and wide‐angle X‐ray diffraction. The addition of 2.5 wt % SEP caused a nucleation effect (by decreasing the crystallite and spherulite size) and randomization of the crystallites. With further SEP addition, the crystallite and spherulite size increased because of prolonged solidification and crystallization and achieved the maximum in the 80/20 iPP/SEP blend. This maximum was a result of the appearance of β spherulites and the presence of mixed α spherulites in the 80/20 iPP/SEP blend. Dispersed SEP particles were irregular and elongated clusters consisting of oval and spherical core–shell microdomains or SEP micelles. SEP clusters accommodated their shapes to interlamellar and interspherulitic regions, which enabled a well‐developed spherulitization even in the 70/30 iPP/SEP blend. The addition of SEP decreased the yield stress, elongation at yield, and Young's modulus but significantly improved the notched impact strength with respect to the strength of pure iPP at room temperature. Some theoretical models for the determination of Young's modulus of iPP/SEP blends were applied for a comparison with the experimental results. The experimental line was closest to the Takayanagi series model. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 566–580, 2001     

Influence of the PVOH molar mass on the morphology and functional properties of EVOH/PVOH films prepared by melt blending

The influences of the molar mass (low, medium, and high) and content of poly(vinyl alcohol) (PVOH) dispersed by melt-blending in an ethylene vinyl alcohol (EVOH) copolymer on the morphology, microstructure, thermal, mechanical, and oxygen barrier properties were investigated. Multilayer films with external low-density polyethylene layers and inner EVOH/PVOH blend layer and respective monolayer films were elaborated and characterized. EVOH/PVOH blends exhibited a good compatibility because of the initial presence of PVOH segments in EVOH. The detailed quantitative analysis of the morphology performed for all blends showed that the finest dispersion was obtained with the PVOH with the lowest molar mass. The properties of the films as a function of the PVOH content and its molar mass were determined herein. Significant improvement of barrier properties was obtained at moderated water activities (up to a_w = 0.6) by using the PVOH with the lowest molar mass. Compared to the neat EVOH material, the oxygen permeability coefficients decreased by a factor 2 by adding 15 vol% PVOH while the thermal and mechanical properties remained similar.     

Dynamic Mechanical Thermal Analysis of Polyamide 6/Biopol Blends

The temperature dependence investigated by means of DMTA of dynamic storage modulusE′, dynamic loss modulus E″ and loss tangent tgδ of blends obtained from polyamide 6 and poly(β-hydroxybutyrate-co-β-hydroxyvalerate) (Biopol D600G) indicated, that the dynamic mechanical properties of the blends containing up to 40% Biopol D600G are governed by the properties of polyamide 6. First at the 50% Biopol D600G content in the blend the transitions of the Biopol phase become visible and dominant. The shifts of the loss modulus maxima of the blends might indicate some interactions between the blend components in the amorphous phase. This revised version was published online in August 2006 with corrections to the Cover Date.     

Nanostructures and thermal‐mechanical properties of cyanate ester/epoxy thermosets modified with poly(ethylene oxide)‐poly(propylene oxide)‐poly(ethylene oxide) triblock copolymer

Phase structures and mechanical properties of epoxy/acryl triblock copolymer alloys using several curing agents were studied. The nanostructured thermosets were obtained at the compositions investigated for every blends studied. The dependence of the morphological structures on block copolymer content and dicyanate ester, 2,2′‐bis(4‐cyanatophenyl) isopropylidene (BCE)/epoxy (EP) ratio for thermosetting blends was interpreted on the basis of the difference in hydrogen bonding interactions and reaction resulting from the cross‐linked network structures of matrixes. Moreover, the effect of F68 (poly(ethylene oxide)‐co‐poly(propylene oxide)‐co‐poly(ethylene oxide) block copolymer) on the curing characteristics and performance of BCE/EP resin was discussed. Results show that the incorporation of F68 cannot only effectively promote the curing reaction of BCE/EP but can also significantly improve the toughness of the cured BCE/EP resin. In addition, the toughening effect of F68/EP is greater than single EP resin. For example, the notched impact strength of systems with BE‐80/20 (B and E being the overall contents of BCE and EP, respectively) modified with 10 wt% F68 showed 55% increase compared with neat BCE/EP resin and even is more than three times of that value for pure BCE resin, 5.9 kJ/cm². Copyright © 2015 John Wiley & Sons, Ltd.     

Dynamic mechanical and rheological properties of binary S–(S/B)–S triblock copolymer blends

The rheology and dynamic mechanical properties of binary block copolymer blends consisting of a symmetrical triblock copolymer with thermoplastic elastomeric behavior (LN4) and an asymmetrical thermoplastic triblock copolymer (LN3) were investigated. TEM images of the blends show a systematic variation in the morphologies from worms (～20–0 wt % LN3) to cylinders (～60–30 wt % LN3) to lamellae (100–70 wt % LN3) as a function of LN3 content. DMA analysis has revealed that the increase in LN3 content leads to a decrease in miscibility between the PS end blocks and the S/B middle block. The frequency and temperature dependence of the storage modulus (G′), loss modulus (G″), and complex viscosity (|η*|) has been studied for LN4 (weakly segregated) and LN3 (strongly segregated) from their master curves. By comparing the rheological properties of these blend compositions at low‐frequency regime, it is observed that with the increase in LN3 content the shear modulus and complex viscosity increase. Blend compositions with 70–100 wt % of LN3 show nonterminal behavior at reduced frequencies due to the presence of highly ordered microdomains when compared to blends with ～0–20 wt % of LN3 content. van Gurp–Palmen plots were constructed to observe the transition from liquid‐ to solid‐like behavior in the vicinity of order‐to‐disorder transition (ODT) temperature. ODT temperature increases as the thermoplastic LN3 content increases which are also confirmed by the Han plots. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 329–343, 2008     

Batch and semicontinuous emulsion copolymerization of vinyl acetate–butyl acrylate. II. Morphological and mechanical properties of copolymer latex films

Vinyl acetate/(VAc)-butyl acrylate/(BuA) copolymer latex films of various copolymer compositions were investigated for their morphological properties by electron microscopy techniques, and for their mechanical properties by dynamic mechanical spectroscopy (DMS), differential scanning calorimetry (DSC), and tensile strength measurements. Batch copolymer latex films showed domains of PBuA dispersed in PVAc matrix; the domain sizes were increased with increased BuA content. Semicontinuous latex films were homogeneous in composition. Glass transition temperatures T_g determined from DMS and DSC indicated the presence of two, low and high, transition temperatures for batch latex films. The two temperatures approached the individual homopolymers, with increased PBuA content up to 51 mol %. Semicontinuous latex films showed only one single T_g. Tensile properties of the batch copolymer films showed a higher ultimate tensile strength, higher Young's modulus, and lower percent elongation to break compared to semicontinuous latex films. These differences were found to reflect the effect of mode of monomer addition during the emulsion copolymerization process on the particle morphology, and confirmed earlier data on bulk, colloidal, and surface properties of the same copolymer latexes.     

氯化聚氯乙烯／环氧树脂共混体的流变性质及形态

氯化聚氯乙烯(CPVC)具有优良的物理性能。但须严格控制加工温度,加工熔体粘度较大。近年,作者曾对CPVC与氯化聚乙烯(CPE)和丙烯酸酯共聚物(ACR)共混体的流变性质进行了研究。本文首次研究CPVC与环氧树脂(EP)共混体的流变性质与形态。     

Specific properties of in situ ruthenium‐catalyzed polyamide 12/polydimethylsiloxane compatibilized blend

The main objective of this work focused on the chemical modification of polyamide 12 (PA12) properties through the reaction with a hydride‐terminated polydimethylsiloxane (PDMS‐SiH). The investigated PA12/PDMS‐SiH blend was compatibilized by ruthenium derivative catalyzed hydrosilylation reaction in molten state. This original route enhanced interfacial adhesion and avoid PDMS‐SiH leaching phenomenon between the two immiscible phases. More specifically, the size of PDMS‐SiH domains in the blend decreased from around 4 μm to 800 nm and from 30 to 1 μm after compatibilization with 10 and 20 wt % PDMS‐SiH, respectively. For the best compatibilized PA12/PDMS‐SiH blend, the introduction of PDMS lowered the surface free energy and the PA12‐based blend turned from hydrophilic to hydrophobic behavior, as evidenced by the water contact angle measurements. Gas permeability and CO₂/H₂ and CO₂/He gas selectivity were also improved with the increase in PDMS content. Besides, the mechanical properties were enhanced with 13% increase in Young's modulus after in situ compatibilization with 15 wt % PDMS‐SiH. Thermal stability was also improved after compatibilization as the initial degradation temperature of reactive blends obviously increased compared with nonreactive ones. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 978–988     

Free volume hole size of Cyanate ester resin/Epoxy resin interpenetrating networks and its correlations with physical properties

Cyanate ester (CE) resin was blended with epoxy resin (EP) at different mass ratios (CE/EP: 100/0, 90/10, 70/30, 50/50, 30/70, 10/90, and 0/100). The curing process of the blend system was characterized by Fourier transform infrared spectrometry (FTIR) and differential scanning calorimetry (DSC). Examination of the mechanical properties, thermal stability, and morphology of the blend systems showed that addition of epoxy resin resulted in improved toughness but a little sacrifice in thermal stability when compared with neat CE. The free volume size of the blend system determined by positron annihilation lifetime spectroscopy (PALS) decreased with the epoxy resin content, which is consistent with the chemical structure changes for the copolymerization between CE and EP. The crosslinking units of curing products (oxazoline, oxazolidinone, and polyether network) of the blends are all smaller in size than those of triazine ring structure from neat CE. Therefore, the free volume size of the blends decreases with increase of EP content. The correlations between the free volume properties and other physical properties (thermal stability and mechanical properties) have also been discussed.     

Steady-state permeation of carbon dioxide through a miscible,glassy polymer blend

Steady-state permeation measurements are reported for carbon dioxide (CO₂) through quenched, amorphous films of a miscible blend of poly(butylene terephthalate) (PBT) and a random copolyester of bisphenol-A and iso/terephthalate acids (PAr). Permeabilities were determined at 35°C on blends with up to 60 wt % PBT and for CO₂ pressures up to 300 psi (2.06 MPa). At a fixed blend composition, the permeability, P̄, decays with driving pressure, p, as described by dual-mode models for gas transport in glassy polymers. From regression fits of the data to dual-mode model predictions for P̄(p), high-and low-pressure limiting permeabilities are determined. These decrease with PBT content in a manner indicating strong, favorable energetic interactions between the PBT and PAr components in the blend. © 1996 John Wiley & Sons, Inc.     

Effect of oil and cured agent content on the structure and properties of thermoplastic vulcanizates

The effect of oil and curing agent content on the mechanical behavior of thermoplastic vulcanizates, based on a polypropylene (PP) and ethylene‐propylene‐diene copolymer (EPDM), was investigated. Mechanical properties such as Young's modulus, stress at 100% elongation and ultimate stress were investigated as a function of blends' composition and phase morphology. Experimental studies show that the Young's modulus of the vulcanizates depends on both PP/EPDM ratio and oil content in the blends; both ultimate strength and stress at 100% elongation increase with curing agent content.     

Compatibilizing effect of functionalized polystyrene blends: a study of morphology,thermal, and mechanical properties

Polystyrene (PS), being an amorphous polymer is immiscible with other polymers. To engender miscible blends, PS has been functionalized with an active amino‐functional group on the molecular chains of PS to yield amino‐substituted polystyrene (APS), which serves as a reactive compatibilizer. The compatibilization effect of amino functionalized polystyrene on the rubber toughening was explored and results were compared in terms of morphology, thermal, and mechanical properties of PS/SEBS‐g‐MA versus APS/SEBS‐g‐MA blends. In addition, the effect of rubber content on the blend morphology and mechanical properties were investigated. An appreciable change in the thermal stability of APS blends in comparison with PS blend has been probed. A marked correlation has been observed between phase morphology and thermal stability. Use of APS produced the compatibilized blends which render improved blend morphology, enhanced thermal and mechanical properties. Optimal thermal, morphological and mechanical profiles were depicted by 20‐wt% APS blend. Copyright © 2008 John Wiley & Sons, Ltd.     

Effect of Electron Beam Irradiation and Ethylene Vinyl Acetate Copolymer on the Properties of NBR/HDPE Blends

The mechanical and physical properties of blends based essentially on nitrile butadiene rubber (NBR) and different ratios of high density polyethylene (HDPE) up to 25 parts per hundred part of rubber (phr) before and after electron beam irradiation were investigated. The values of tensile strength (TS), tensile modulus at 50% elongation (M₅₀), hardness and gel fraction % (GF%) of NBR/HDPE blends were increased with both irradiation dose and by increasing the content of HDPE in the blends. On the other hand, the values of elongation at break (E _b ) were decreased with both irradiation dose and the content of HDPE in the blends. By loading NBR/HDPE (100/25) blend with ethylene vinyl acetate (EVA) copolymer the mechanical and physico-chemical properties were improved. Moreover, the degree of improvement is proportional to the loading content of EVA.     

Structure-property relationships in a reactively coupled ductile matrix/brittle dispersed phase blend

Blends of t-butylaminoethyl methacrylate grafted polyethylene (PE-g-tBAEMA) with methyl methacrylate-methacrylic acid copolymer (PMMA-MAA) and polymethyl methacrylate (PMMA) were prepared in a Banbury type batch mixer. The effects of component proportions and processing conditions on the melt flow index, morphology, impact, and tensile properties of the resulting polymer blends were investigated. The interfacial chemical reaction was studied using Fourier transform infrared (FTIR) technique. It was observed that the melt index of the blends was reduced with increasing melt processing temperature and mixing time, indicating the formation of PE-g-PMMA block copolymer. New IR bands at 1554, 1628, 1800, and 1019 cm^?1 were observed only for PE-g-tBAEMA/PMMA-MAA, the reactive blends, but not for PE-g-tBAEMA/PMMA, the nonreactive blend. These IR bands were attributed to the amide, carboxylate anion and methacrylimide formation resulting from the chemical reaction between the secondary amine on the PE-g-tBAEMA/PMMA moiety and the carboxylic acid on PMMA-MAA segment. The morphology of the blends in various compositions was examined using scanning electron microscopy (SEM) and related to their mechanical properties. All of the blends have a domain structure whose morphology is strongly dependent on the concentration of the dispersed phase. Furthermore, the PE-g-tBAEMA/PMMA-MAA reactive blends were shown to have much finer morphology than the corresponding nonreactive blends. For the reactive polymer blends consisting of brittle particles dispersed in the ductile matrices, the PE-g-tBAEMA/PMMA-MAA, impact and tensile result higher than predicted by the additivity rule were observed. The toughening of polyethylene by PMMA was explained by a “cold-drawing” mechanism. The Young's modulus of the blends and the extent of interfacial adhesion were analyzed with Takayanagi and Sato-Furukawa's theories. © 1993 John Wiley & Sons, Inc.     

Thermal oxidative stability and effect of water on gas transport and mechanical properties in PA6‐EVOH films

The thermal oxidative stability and the effect of water on gas transport and mechanical properties of blends of polyamide 6 (PA6) with ethylene‐co‐vinyl alcohol (EVOH) and EVOH modified with carboxyl groups (EVOH‐COOH) have been investigated. The presence of EVOH reduces water vapor and oxygen gas permeability of polyamide, as well as small amounts of EVOH‐COOH further improve barrier properties, especially to oxygen. This has been explained in terms of improved interactions of the blend constituents in the amorphous phase, due to ionic linkages between the polyamide amino groups and the carboxyls of modified EVOH. The permeation to gases was found to increase with the amount of sorbed water. The morphology of the samples was found to have an effect on barrier properties, as the presence of EVOH causes the PA6 α crystalline form to increase, lowering the permeability to oxygen and water vapor. Mechanical properties are strongly affected by water sorption, as tensile modulus and strength decrease with increasing water content. Chemiluminescence (CL), infrared spectroscopy (FTIR), and tensile test were employed in order to assess the correlation between chemical composition and the thermal oxidative stability of the films aged at 110 °C in air. CL experiments suggest that the presence of EVOH and EVOH‐COOH efficiently inhibits the formation of peroxidized species during the processing, and increases the thermal oxidative stability of the films. Infrared spectroscopy showed a build‐up of carbonyl absorption in the range 1700–1780 cm^?1, due to the formation of oxidation products, which is greater in the case of the pure polymer. Tensile tests on films revealed a reduction in ductility as a result of ageing for neat PA6, whereas in comparison the blends exhibit a far better long‐term stability. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 840–849, 2007