The distribution coefficient of oil and curing agent in PP/EPDM TPV

The distribution coefficients of oil and curing agent in PP/EPDM TPV were calculated by measuring the melting point of the PP phase using differential scanning calorimetry (DSC). The PP/EPDM TPV was prepared by using a twin screw extruder and a peroxide curing agent was used. The peroxide induces the degradation of PP, resulting in the decrease of T_m. The oil in PP phase also decreases the Tm. Based on the T_m difference among pure PP and PP/EPDM TPV before and after extraction by cylcohexane, the calculated oil distribution coefficient is 0.537. The addition sequence of PP, oil, and curing agent has a significant effect on the T_m and the calculated curing agent distribution coefficient is 0.52. Both of the coefficients are less than 1. Based on the calculation of the two coefficients, a rationale design of thermoplastic vulcanizate (TPV) can be made by proper control of raw materials, addition sequence, and processing parameters. Copyright © 2007 John Wiley & Sons, Ltd.     

接枝和交联对纳米SiO_2改性NR/PP共混型热塑弹性体的影响

动态硫化制备纳米二氧化硅(SiO2)改性天然橡胶/聚丙烯共混型热塑性弹性体(NR/PP TPE).研究了马来酸酐/苯乙烯/过氧化二异丙苯(MAH/St/DCP)多单体“就地”熔融接枝、交联对TPE力学性能、耐溶剂性能和耐热变形性能的影响,并用SEM分析了TPE的断面形貌.结果表明:纳米SiO2和MAH/St/DCP的最佳质量分数分别为0.03和0.0375/0.0188/0.00375时,MAH/St/DCP接枝、交联改性NR/PP/纳米SiO2TPE的力学性能、耐溶剂性能和耐热变形性能最佳.MAH/St/DCP“就地”接枝、交联通过细化交联NR分散相、改善交联NR分散的均匀性和增加两相之间的共交联,使NR与PP两相界面结合强度明显提高,NR/PP TPE的综合性能得到明显的改善.     

接枝和交联对纳米Si02改性NR／PP共混型热塑弹性体的影响

动态硫化制备纳米二氧化硅（SiO2）改性天然橡胶，聚丙烯共混型热塑性弹性体（NR/PPTPE）．研究了马来酸酐，苯乙烯，过氧化二异丙苯（MAH／St／DCP）多单体“就地”熔融接枝、交联对TPE力学性能、耐溶剂性能和耐热变形性能的影响，并用SEM分析了TPE的断面形貌．结果表明：纳米SiO2和MAH／St／DCP的最佳质量分数分别为0．03和0．0375／0．0188／0．00375时，MAH／St／DCP接枝、交联改性NR／PP／纳米SiO：TPE的力学性能、耐溶剂性能和耐热变形性能最佳．MAH／St／DCP“就地”接枝、交联通过细化交联NR分散相、改善交联NR分散的均匀性和增加两相之间的共交联，使NR与PP两相界面结合强度明显提高，NR／PPTPE的综合性能得到明显的改善．     

Uncross‐linked polypropylene (PP)/ethylene‐propylene‐diene (EPDM)/multi walled carbon nanotube (MWCNT) and dynamically vulcanized PP/EPDM/MWCNT nanocomposites

In this study, relatively large amounts of polypropylene (PP), ethylene‐propylene‐diene (EPDM), and multi‐walled carbon nanotube (MWCNT) were melt‐mixed with and without DCP. Dynamically vulcanized PP/EPDM (TPV)/MWCNT nanocomposites were prepared by two methods: the MWCNTs were added either before or after the dynamic vulcanization of the blends. The effects of composition, rotor speed, and dynamic vulcanization on their surface resistivity were investigated. The surface resistivity of uncross‐linked PP/EPDM/MWCNT nanocomposites increases with increasing the content of EPDM. At PP/EPDM (70/30 wt%) nanocomposite with 1.5 phr MWCNT, slightly lower surface resistivity is obtained by increasing the rotor speed during mixing. However, for PP/EPDM (50/50 wt%) and PP/EPDM (30/70 wt%) nanocomposites, surface resistivity decreases with increasing the rotor speed from 30 to 60 rpm. But further increase in rotor speed (90 rpm) leads to an increase of surface resistivity. When the MWCNTs were added after the dynamic vulcanization of the blends, the surface resistivity of TPV70/MWCNTnanocomposite is lower than that of uncross‐linked PP/EPDM/MWCNT nanocomposite. However, when the MWCNTs were added before the dynamic vulcanization of the blends, the surface resistivity of TPV70/MWCNT nanocomposite is >10¹² Ω/square. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation of polypropylene/ethylene‐propylene‐diene terpolymer/nitrile rubber ternary thermoplastics vulcanizates with good mechanical properties and oil resistance by core‐shell dynamic vulcanization

As the most successful commercialized thermoplastic vulcanizates (TPVs), polypropylene (PP)/ethylene propylene rubber (EPDM) TPVs exhibit poor oil resistance. In this work, we prepared PP/EPDM/butadiene acrylonitrile rubber (NBR) ternary TPVs with good oil resistance using core‐shell dynamic vulcanization. According to the theoretical analysis of the spreading coefficient and the transmission electron microscopy results, the rubber phases exhibited a special core‐shell structure, in which the cross‐linkedNBR‐core was encapsulated by the EPDM‐shell. The core‐shell structure effectively improved the interfacial compatibility between PP and NBR phase as the EPDM‐shell could avoid the direct contact of them, thus improving the mechanical properties of the TPVs. For example, the PP/EPDM/NBR (40/30/30) ternary TPV showed enhanced tensile strength of 12.57 MPa, compared with 10.71 MPa of PP/EPDM (40/60) TPV and 11.11 MPa of PP/NBR (40/60) TPV, respectively. Moreover, the oil resistance of the TPVs was also improved. Compared with PP/EPDM TPV, the change rates in mass, volume, tensile strength and elongation at break of PP/EPDM/NBR TPV after oil immersion decreased by 42.18%, 48.69%, 52.68% and 28.77%, respectively.     

聚丙烯熔融接枝马来酸酐反应机理的研究

改变聚丙烯（PP）熔融接枝马来酸酐（MAH）反应中的单体和引发剂的浓度以及添加适当助剂,考察了接枝产物的接枝率和恒定剪切应力（600kPa)及温度（210℃）下的剪切粘度,验证了作先前所提出的PP熔融接枝MAH的反应机理。即：在PP熔融接枝MAH的过程中,过氧化物自由基在熔融接枝过程中直接引发MAH单体及MAH单体在聚丙烯的大分子链段发生β断裂前直接被其引发而产生的接枝反应是影响产物的接枝率和分子量的关键。在不改变单体和引发剂浓度的情况下,降低过氧化物自由基在熔融接枝过程中直接引发MAH单体反应的程度而提高聚丙烯的大分子自由基直接引发MAH单体的反应趋势,是提高接枝产物接枝率和分子量的有效途径。     

Electrical insulation performance of flame retardant fillers filled with polypropylene/ethylene propylene diene monomer composites

Flame retardant fillers composed of zinc hydroxy stannate (ZHS), calcium borates (CaB), and NP‐100 were embedded separately in 50% polypropylene (PP) and 50% ethylene propylene diene monomer (EPDM) blends. Several formulations containing flame retardant fillers, PP, and EPDM were prepared using an internal mixer and were molded in a compression mold to form test samples. The effects of filler loading (15, 30, 45, and 60 vol%) on the dielectric breakdown strength and contact angle were determined. It was found that PP/EPDM/NP‐100 has higher breakdown strength than PP/EPDM/ZHS and PP/EPDM/CaB. The contact angle of PP/EPDM/NP‐100 and PP/EPDM/ZHS showed an ascending order with filler loading, implying an increase in hydrophobicity. With regard to the PP/EPDM/CaB system, the contact angle showed an ascending order up to 30 vol% followed by a descending order at 45–60 vol%. Water absorption studies indicated that PP/EPDM/NP‐100 has lower water absorption compared with PP/EPDM/ZHS and PP/EPDM/CaB. PP/EPDM filled with 15 vol% NP‐100 was found to exhibit interesting insulating properties in comparison with other composite systems, thanks to high breakdown voltage, good hydrophobicity, and low water absorption. Copyright © 2014 John Wiley & Sons, Ltd.     

马来酸酐-苯乙烯熔融接枝聚丙烯的影响因素及其性能研究

用单螺杆挤出机制备了马来酸酐 (MAH) 苯乙烯 (St)对聚丙烯 (PP)的多组分单体自由基熔融接枝体系 .研究证实了当两种单体物质的量比约为 1∶1时 ,接枝物的接枝率最高 ,而熔体流动速率 (MFR)最大 .对反应体系影响因素的研究表明单体用量和引发剂用量对不同单体用量比的系列接枝物的接枝率会产生不同的影响 ;另外 ,单体用量增加 ,接枝物的MFR减小 ,过氧化二异丙苯 (DCP)用量增加 ,接枝物的MFR增加 .对多单体熔融接枝聚丙烯PP g (MAH co St)的力学性能研究发现 ,选用合适的单体用量比、单体用量和DCP用量时 ,所制备的接枝物可具有与纯PP相当或更佳的力学性能     

Synthesis of a [60] fullerene—Functionalized isotactic polypropylene derivative

The covalent attachment of [60] fullerene (C₆₀) to isotactic polypropylene (i‐PP) is achieved by direct reaction in 1,2,4‐trichlorobenzene (TCB) solution in the presence of dicumyl peroxide (DCP). The chemically modified pendant C₆₀/i‐PP polymers are soluble in chlorinated solvents and have been characterized by ultraviolet–visible and fourier transform infrared spectroscopy, scanning electron microscopy, X‐ray diffraction, differential scanning calorimetry, cyclic voltametry, and thermogravimetric analysis. From the results it can be concluded that the modification of i‐PP by grafting via a free‐radical reaction competes with the possibility of chain scission of i‐PP due to the presence of DCP. The functionalized polymers crystallize in the monoclinic crystal modification, and have high crystallinity. The incorporation of C₆₀ significantly enhances the thermal stability of the i‐PP. Electrochemical measurements demonstrate good electron acceptor properties of the fullerenated i‐PP samples. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6722–6733, 2008     

GMA熔融接枝EPDM的研究

以甲基丙烯酸缩水甘油酯（ＧＭＡ）为接枝单体，过氧化二异丙苯（ＤＣＰ）为引发剂，对三元乙丙胶（ＥＰＤＭ）进行了熔融接枝，在烃链上引入极性基团，以改善ＥＰＤＭ与极性聚合物的相容性。用差示扫描量热计（ＤＳＣ）研究了ＧＭＡ的聚合温度，用富里叶红外（ＦＴ－ＩＲ）、凝胶渗透色谱（ＧＰＣ）对接枝产物进行了表征。实验结果表明，产物的接枝率和凝胶量可以通过反应条件（温度、时间、反应物组成及加料方式）来控制。     

PP/EPDM/CaCO3三元复合材料的相结构及力学性能研究

采用以化学键合方式在CaCO3表面包覆上聚丙烯蜡和将改性后的CaCO3先与EPDM复合、再与PP复合的工艺,制备PP/EPDM/CaCO3三元复合材料,以期在PP基体材料中得到EPDM包裹CaCO3的相结构.通过测量三元复合体系中各组分的表面张力,计算各可能组分对之间的界面张力和黏结功,分析三元复合体系中可能的相结构.热力学计算结果表明,三元复合体系中既存在以EPDM为壳、CaCO3为核的"核壳结构",又存在CaCO3与EPDM各自独立分散在PP基体中的结构.电镜照片进一步揭示,在PP/EPDM/改性CaCO3三元复合体系与PP/EPDM/未改性CaCO3三元复合体系中,这两种相结构的比例是不同的,在前者中以核壳结构为主.CaCO3表面性质的不同是产生这一差别的原因.由于这一结构差别的存在,PP/EPDM/改性CaCO3三元复合体系比PP/EPDM/未改性CaCO3三元复合体系具有更好的力学性能.当EPDM用量为8 phr、改性CaCO3用量为15 phr时,三元复合体系的冲击强度达14.25 kJ/m2,是纯PP的3.17倍.     

Ultrasonically Initiated Grafting of Maleic Anhydride onto Poly(propylene)

This paper presents the studies on the grafting of MAH onto PP performed in solution by means of ultrasonic initiation. The effect of sonic intensity and monomer concentration on the amount of grafted MAH was investigated. It was found that grafting reaction could be initiated by ultrasound at ambient temperatures in the absence of an initiator. The quantity of product grafted was found to be 1.35%. It has been shown that optimum conditions for grafting are reached at an ultrasonic intensity of 300 W and a MAH concentration of 30%. PP‐g‐MAH is characterized by FTIR and XRD. DSC shows that the crystallinity of PP‐g‐MAH is lower than that of pure PP.

     

Studies on grafting of tris(2‐methoxyethoxy)vinylsilane onto ethylene‐propylene‐diene terpolymer

New graft copolymer was prepared by incorporating tris(2‐methoxyethoxy)vinylsilane (TMEVS) on ethylene‐propylene‐diene terpolymer (EPDM) by using dicumyl peroxide (DCP) as initiator, in Haake Rheocord 90 torque rheometer. The effect of EPDM concentration, TMEVS concentration, reaction time, reaction temperature and initiator concentration on the graft co polymerization was studied. The grafting efficiency of TMEVS on EPDM was confirmed by Fourier Transform infrared (FT‐IR) spectroscopy. The grafting efficiency increased with increase in the silane concentration upto 6% by weight. The grafting efficiency decreased beyond 6% by weight due to homopolymerization of TMEVS and non‐availability of carbon–carbon double bond in the EPDM terpolymer. The thermal properties of peroxide cured EPDM and hot water cured EPDM‐g‐TMEVS were studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis. The results show thermal properties like degradation tempertature and glass transition temperature of the EPDM‐g‐TMEVS were increased due to introduction of TMEVS on to EPDM terpolymer as well as the formation of thermally stable three‐dimensional network. Copyright © 2004 John Wiley & Sons, Ltd.     

Investigation of phase morphology of incompatible polyethylene/nylon 6 blends containing EPDM-based functionalized compatibilizers

Graft copolymer and graft terpolymer were prepared by solution grafting of maleic anhydride (MAH) or acrylonitrile (AN) alone and mixture of MAH and AN on to ethylene–propylene–diene terpolymer (EPDM) using benzoyl peroxide (BPO) as an initiator. The resulting EPDM-g-MAH, EPDM-g-AN and EPDM-g-(MAH-co-AN) have been used to obtain a binary blend of Nylon 6/functionalized EPDM and a ternary blend of polyethylene/Nylon 6/functionalized EPDM by melt blending. The effects of the nature and the amount of the grafted species on the phase morphology, crystallization behavior and mechanical properties of the blends were characterized through scanning electron microscopy, optical microscopy, infrared spectroscopy and using a dynamic mechanical analyzer. From the morphological study, it can clearly be seen that the presence of the functionalized EPDMs in these blends resulted in an improvement of the dispersion degree in incompatible polyethylene/Nylon 6 blends.     

PP-g-(MAH/St)和PP-g-MAH对聚丙烯/木粉复合材料性能的影响

在转矩流变仪中用熔融接枝法制备马来酸酐(MAH)和苯乙烯(St)接枝聚丙烯（PP）-PP-g-(MAH/St)和PP-g-MAH,将其作为聚丙烯/木粉复合材料的相容剂。 FTIR证实MAH和St单体与PP发生接枝反应。 用SEM和DSC等手段考察两种相容剂对PP/木粉复合材料微观形貌和结晶性能的影响,探索了各种PP/木粉复合材料加工和力学性能不同的内在原因。 SEM显示,PP-g-(MAH/St)改性木粉比PP-g-MAH改性木粉在PP基体中分散性更佳,木粉与PP的界面更加模糊,相容性进一步改善。 DSC结果表明,PP-g-(MAH/St)改性体系可增强木粉对PP的异相成核作用,提高结晶温度和结晶度。 复合材料的加工和力学性能测试结果表明,PP-g-(MAH/St)改性效果明显优于PP-g-MAH。 复合材料的熔体质量流动速率随相容剂用量的增加而逐步下降,PP-g-(MAH/St)改性体系拉伸强度和弯曲强度却逐步上升,并在相容剂用量为4.8 g/100 g PP时达到极值。 此时其拉伸强度达40.62 MPa,分别是未改性体系和PP-g-MAH改性体系的1.29和1.17倍;其弯曲强度达45.72 MPa,分别是未改性体系和PP-g-MAH改性体系的1.23和1.59倍;而无缺口冲击强度却在相容剂用量为3.6 g/100 g PP时达到极值13.35 kJ/m2,分别是未改性体系和PP-g-MAH改性体系的1.62倍和1.42倍。     

羟基不饱和脂肪酸改性纳米碳酸钙对聚丙烯微观形态和流变性能的影响

采用羟基不饱和脂肪酸,通过固相法对硬脂酸改性的工业纳米碳酸钙CCR进行表面改性制备了R-CCR,红外光谱(FTIR)显示改性剂已结合在碳酸钙表面.通过熔融共混法制备了聚丙烯(PP)/乙丙橡胶(EPDM)/纳米碳酸钙二元和三元复合材料.并利用扫描电子显微镜(SEM)和透射电子显微镜(TEM)观察复合材料的微观形态,发现R-CCR的加入,使PP复合材料的拉伸断面出现明显的拉丝状结构和大面积的屈服变形,与PP/EPDM/CCR相比,PP/EPDM/R-CCR冲击断面的空穴明显增加并细化,R-CCR在PP基体中分散均匀,且界面模糊,与基体的相容性明显优于CCR.复合材料流变行为的研究表明R-CCR的加入,体系储存模量G′和损耗模量G″随频率的增加而增加,对损耗因子和复数粘度的影响不大;但PP/EPDM/R-CCR复合材料的表观粘度,明显低于PP/EPDM/CCR和纯PP,同时,剪切速率的增加可有效降低体系的表观粘度.力学性能表明,R-CCR对PP同时起到增韧和增强的效果.且R-CCR和EPDM对PP具有协同增韧的效果.在保持聚丙烯的模量和强度基本不变的前提下,大幅度的改善聚丙烯的韧性,同时加工性能保持不变.     

Simultaneous enhancement of electrical conductivity and impact strength via formation of carbon black‐filler network in PP/EPDM Blends

The electrical conductivity and impact strength of polypropylene(PP)/EPDM/carbon black ternary composites were investigated in this paper. Two processing methods were employed to prepare these ternary composites. One was called one‐step processing method, in which the elastomer and the filler directly melt blended with PP matrix. Another one was called two‐step processing method, in which the elastomer and the filler were mixed first, and then melt blended with pure PP. To get an optimal phase morphology that favors the electrical conductivity and impact strength, controlling the distribution of CB in PP/EPDM blend was a crucial factor. Thus the interfacial tension and the work of adhesion were first calculated based on the measurement of contact angle, and the results showed that CB tended to be accumulated around EPDM phases to form filler‐network structure. Expectably, the filler‐network structure was observed in PP/EPDM/CB(80/20/3) composite prepared by two‐step processing method. The formation of this filler‐network structure decreased the percolation threshold of CB particles in polymer matrix, and the electrical conductivity as well as Izod impact strength of the composite increased dramatically. This work provided a new way to prepare polymer composites with both improved conductivity and impact strength. Copyright © 2009 John Wiley & Sons, Ltd.     

Reactive melt blends of thermoplastic polyolefins,MAH‐g‐PP and nylon 6

Reactive melt blends of an ethylene‐propylene‐diene terpolymer (EPDM) based thermoplastic elastomer (TPE), maleic anhydride grafted polypropylene (MAH‐g‐PP), and nylon 6 were prepared in a single screw extruder and evaluated in terms of morphological, rheological, thermal, dynamic mechanical, and mechanical properties of the blends. It was found that MAH‐g‐PP‐co‐nylon 6 copolymers were in situ formed and acted as effective compatibilizers for polypropylene (PP) and nylon 6. Phase separation of PP and EPDM in TPE increased with the addition and increasing amount of MAH‐g‐PP and nylon 6, leading to decreased glass transition temperature (T_g) of TPE and increased crystalline melting temperature (T_m) of PP. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and enhanced properties of poly(propylene)/ silica‐grafted‐hyperbranched polyester nanocomposites

A series of poly(propylene) silica‐grafted‐hyperbranched polyester nanocomposites by grafting the modified hyperbranched polyester (Boltorn? H20), possessing theoretically 50% end carboxylic groups and 50% end hydroxyl groups, which endcapped with octadecyl isocyanate (C19), onto the surface of SiO₂ particles (30 nm) through 3‐glycidoxy‐propyltrimethoxysilane (GPTS) was prepared. The effect of silica‐grafted‐modified Boltorn? H20 on the mechanical properties of polypropylene (PP) was investigated by tensile and impact tests. The morphological structure of impact fracture surface and thermal behavior of the composites were determined by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), respectively. The melt viscosity of composites was investigated by melt flow index (MFI). The obtained results showed that: (1) the modified Boltorn? H20 was successfully grafted onto the SiO₂ surface confirmed by FT‐IR and X‐ray photoelectron spectroscopy (XPS) analysis; (2) the incorporation of silica‐grafted‐modified Boltorn? H20 (3–5 wt% SiO₂) greatly enhanced the notched impact strength as well the tensile strength of the composites; (3) the incorporation of silica‐grafted‐modified Boltorn? H20 had no influence on the melting temperature and crystallinity of PP phase; (4) the MFI of PP composites increased when the silica‐grafted‐modified Boltorn? H20 particles were added compared with PP/SiO₂ or PP/SiO₂‐GPTS composites. Copyright © 2004 John Wiley & Sons, Ltd.     

Morphology development and phase inversion during dynamic vulcanisation of EPDM/PP blends

Morphology development and phase inversion were investigated during dynamic vulcanisation of ethylene–propylene–diene terpolymer (EPDM)/polypropylene (PP) blends. The effects of viscosity ratio and cross-linking reactions were also addressed. EPDM/PP blends were dynamically vulcanised in a Haake batch mixer using resole and SnCl₂ as cross-linking agents. The morphology development and cross-linking degree with reaction time were followed by morphology analysis (SEM and TEM) and measurement of EPDM gel content, respectively. For the same reaction time, it was found that the EPDM gel content decreased when the low-molecular-weight EPDM was used. As a result, the morphological development was delayed and the phase-inversion point was shifted to higher reaction times, allowing us to monitor morphological development during a thermoplastic vulcanisate (TPV) preparation. Using the low-molecular-weight EPDM and increasing the PP viscosity accelerated the morphological development, shifting phase-inversion to lower reaction times. While blend composition influenced final TPV morphology, it had a minor effect on the mechanism of morphological development. A correlation between cross-linking degree and morphology development was established. The results obtained allowed to propose a mechanism of morphology development during dynamic vulcanisation of the EPDM/PP blends, including phase inversion.