超级微波消解-电感耦合等离子体发射光谱(ICP-OES)法测稀土废料中15种稀土元素

稀土废料已成为战略性物质且不可再生,针对其回收利用已成为一个重要的发展方向,开发稀土废料中稀土元素的快速准确定量的方法至关重要。超级微波消解法解决了湿法消解法的元素损失、易引入污染的问题。本研究采用超级微波消解法采用硝酸-盐酸-过氧化氢及硝酸-盐酸-过氧化氢-氟硼酸消解体系和使用湿法消解法采用硝酸-盐酸-过氧化氢消解体系进行条件实验,利用电感耦合等离子体发射光谱法进行分析,通过比较消解效果、检出限、精密度及加标回收率,确定使用超级微波消解法采用硝酸-盐酸-过氧化氢-氟硼酸(4.5mLHCl-1.5mLHNO3-0.5mL H2O2-4mL HBF4)消解体系,并优化了消解条件。实验结果表明,使用超级微波消解法采用硝酸-盐酸-过氧化氢-氟硼酸消解体系可以较好的完成对稀土废料的处理,15种元素的检出限为0.120~6.62 mg/kg,15种元素测定结果相对标准偏差（RSD,n=7）均小于1.7%,加标回收率在97.4%~102%之间,方法准确度及精密度均可以满足多种元素分析测试要求,该方法可以实现稀土废料中稀土元素的准确测定。     

微波消解电感耦合等离子体质谱法测定桃中稀土元素及其分布

以市场销售的桃为实验材料,利用微波消解电感耦合等离子体质谱法(ICP-MS)同时测定桃中稀土元素的含量。样品经过硝酸-氢氟酸-双氧水微波消解,实现了桃中16种稀土元素的测定。各元素的检出限在0.004~0.020μg·g-1之间,方法精密度在0.78%~2.96%,回收率在95.0%~106.0%之间。比较了稀土元素在果皮和果肉中的分布。结果表明,稀土元素在果皮中的含量明显高于果肉。本法快速、准确,可用于桃等水果中稀土元素的测定。     

电感耦合等离子体发射光谱法测定膨化食品中铝

目的探讨微波消解-电感耦合等离子体发射光谱法(ICP-OES)测定膨化食品中铝的可行性。方法样品经微波消解后,采用ICP-OES对膨化食品中铝进行测定。结果 ICP-OES法相对标准偏差(RSD)4.0%,线性相关系数0.999 9,回收率88.46%。结论 ICP-OES测定膨化食品中铝具有RSD小、线性相关系数好、准确度高、测定快速等优点,是测定膨化食品中铝的理想方法。     

动能歧视(KED)-电感耦合等离子体质谱(ICP-MS)法测定贵州沉积型稀土矿中16种稀土元素

贵州沉积型稀土矿主要含有高岭土-锐钛矿石等矿物,存在高含量Si、Al、Fe、Ti、Zr等难溶基体元素,采用高压密闭微波消解法处理难以将其完全溶解,易使测定结果偏低,需再次消解或进一步电热板敞开酸溶处理,方法耗时长,不利于大批量样品检测需求。同时电感耦合等离子体质谱法(ICP-MS)在测定稀土元素时存在基体效应和质谱干扰,影响了检测数据的准确性。本文采用过氧化钠熔融分解样品,熔融物冷却后引入三乙醇胺溶液,在碱性溶液中,大量基体元素与三乙醇胺形成稳定配合物,并与大量溶剂钠盐存于溶液中,稀土元素与Ca、Mg、Sr、Ba等留存于沉淀,经过滤,实现稀土元素与大量基体元素分离,随后沉淀用(1+1)硝酸复溶,并以103Rh和185Re为在线注入内标协同降低基体干扰;启用动能歧视(KED)模式以降低测定过程中潜在的质谱干扰。实验结果表明:高压密闭微波消解法消解液浑浊有残渣,溶矿耗时长,测试结果偏低,碱溶法酸化后溶液清亮透明,稀土元素测定值准确性高;经条件试验,采用10%三乙醇胺溶液提取能较大降低基体干扰;启用KED模式可降低测定过程中的质谱干扰,且准确度优于STD模式;碱溶法方法检出限为0.008μg/g~0.049μg/g,测定下限为0.034μg/g~0.195μg/g,相对标准偏差RSD在0.78%～10.2%之间,相对误差RE在0.0225%~13.5%之间。经实际样品验证,碱熔法较适用于贵州沉积性稀土矿中16种稀土元素的测定。     

测定食品及生物样品中微量锡的消化方法探讨

采用干灰化、硝酸-高氯酸、硝酸-硫酸-高氯酸和用硝酸过氧化氢微波消解4种消化方法消化样品,氢化物发生-原子荧光光谱法测定食品及生物样品中微量锡。方法线性范围为20.0μg.L-1以内,相关系数为0.999 8,经过比较,微波消解和硝酸-硫酸-高氯酸消解方法较理想,回收率分别为98.2%~101.4%和97.4%~102.8%,相对标准偏差分别为2.39%~3.85%和3.25%~3.82%。只测定锡时,微波消解和硝酸-硫酸-高氯酸消解法均可,但如锡与其他微量元素需要同时测定,为避免引入有干扰的硫酸根,以用硝酸-过氧化氢微波消解为好。     

微波消解-ICP-OES法同时测定化妆品中Pb、As、Hg

采用微波消解ICP-OES法同时测定化妆品中Pb、As、Hg的含量,并对ICP-OES法测定化妆品消解液时分析线的选择,入射功率、泵速的影响,以及进行检测限、准确度、精密度的研究.用微波消解ICP-OES法测试化妆品中重金属检测结果快速准确.     

微波消解样品-电感耦合等离子体质谱法测定植物灰分中微量元素

应用电感耦合等离子体质谱法(ICP-MS)同时测定植物灰分中21种微量元素和15种稀土元素.用微波消解样品,对微波消解植物灰分样品的条件进行了试验.其优选微波消解条件为:微波压力为2 MPa,消解时间为10 min,以硝酸、盐酸、氢氟酸、高氯酸(体积比为6比2比1比1)的混合酸消解样品,对0.100 0 g植物标准物质(GBW 07603)进行10次平行测定,微量元素测定结果的相对标准偏差(n=10)在0.87%～5.96%之间,稀土元素测定结果的相对标准偏差(n=10)在2.14%～8.00%之间.     

微波消解石墨炉原子吸收光谱法测定氢化棉籽油中痕量镍

建立了微波消解样品、塞曼扣背景石墨炉原子吸收测定氢化棉籽油中痕量镍的方法。向0.050 0 g氢化棉籽油样品中加入2 m L的硝酸和0.5 m L双氧水,于微波消解仪中消解,用石墨炉原子吸收法测定样品溶液中镍的含量。镍的含量在0.1~50 ng/m L范围内与其吸光度呈良好的线性关系,线性相关系数为0.998 2,检出限为15pg/m L。测定结果的相对标准偏差为2.33%(n=11),样品加标回收率为94%~102%,该方法的测定结果与美国药典法基本一致。该方法样品处理方法快速、简单,背景空白低,测定结果准确、可靠,适合于实际样品分析。     

微波消解样品-电感耦合等离子体原子发射光谱法测定铅精矿中铅、砷、镉、汞

采用微波消解样品-电感耦合等离子体原子发射光谱法同时测定铅精矿中主体元素铅及有毒有害元素砷、镉、汞的含量。0.20g试样置于消解罐中,先后加入硝酸9mL、盐酸3mL、氟硼酸2mL及过氧化氢2.5mL,密闭罐盖按设定的微波消解程序进行消解。试验选择铅、砷、镉和汞的分析线分别为220.351,189.042,228.802,184.950nm以消除基体干扰。铅、砷、镉、汞的检出限分别为16.0,2.2,0.4,0.8μg.g-1。方法用于铅精矿标准样品(GBW 07617)和铅精矿实际样品分析,此方法的测定值与认定值及原子吸收光谱法或原子荧光光谱法的测定值相一致。方法的相对标准偏差(n=10)在0.15%～3.9%之间。     

微波消解-电感耦合等离子体发射光谱法同时测定燃料油及润滑油中9种微量金属元素

本文建立了测定燃料油和润滑油样品中Al、Ba、Ca、Cu、Fe、Mg、Mn、Pb、Zn 9种微量金属元素的微波消解-电感耦合等离子体发射光谱法(ICP-OES)。实验探讨了油样的微波消解及ICP-OES测定条件。优化条件下方法加标回收率为93%~102%,相对标准偏差(RSD)3%(n=7)。该方法准确、灵敏,适用于燃料油和润滑油中微量金属元素的分析测定。     

Darstellung,Kristallstrukturen, Schwingungsspektren und Normalkoordinatenanalyse von vier bindungsisomeren Trichlorotrirhodanoosmaten(IV)

Preparation, Crystal Structures, Vibrational Spectra, and Normal Coordinate Analysis of four Linkage Isomeric Trichlorotrirhodanoosmates(IV) By treatment of fac-[OsCl₃I₃]^2? with (SCN)₂ in dichloromethane the linkage isomers fac-[OsCl₃(NCS)₃]^2? ( 1 ), mer-[OsCl₃(NCS)₂^c(SCN)]^2? ( 2 ), mer-[OsCl₃(NCS)(SCN)₂^t]^2? ( 3 ), and mer-[OsCl₃(NCS)(SCN)₂^c]^2? ( 4 ) are formed which have been separated by ion exchange chromatography on diethylaminoethyl cellulose. X-Ray structure determinations have been performed on single crystals of fac-(Ph₄As)₂[OsCl₃(NCS)₃] (triclinic, space group P1 , a = 12.142(5), b = 13.233(5), c = 19.300(5) Å, α = 98.642(5)º, β = 100.509(5)º, γ = 112.514(5)º, Z = 2), mer-(Ph₄As)₂[OsCl₃(NCS)₂^c (SCN)] · acetone (triclinic, space group P1 , a = 11.707(5), b = 13.238(5), c = 19.048(5) Å, α = 75.960(5)º, β = 88.981(5)º, γ = 69.999(5)º, Z = 2), mer-(Ph₄As)₂[OsCl₃(NCS)(SCN)₂ ^t] (triclinic, space group P1, a = 10.6861(12), b = 11.6587(5), c = 12.5232(5) Å, α = 112.069(8)º, β = 95.052(8)º, γ = 92.559(7)º, Z = 1) and mer-(Ph₄As)₂[OsCl₃(NCS)(SCN)₂ ^c] · 2acetone (triclinic, space group P1 , a = 11.444(5), b = 14.661(5), c = 15.830(5) Å, α = 75.790(5)º, β = 80.273(5)º, γ = 75.205(5)º, Z = 2). The complex anions are completely ordered. The via N or S coordinated thiocyanate groups are located nearly direct above one of the cis-positioned Cl ligands with Os? N? C angles of 169.1º, 171.5º, 175.7º ( 1 ), 175.6º, 178.6º ( 2 ), 172º ( 3 ), and 173.1º ( 4 ) and Os? S? C angles of 106.2º ( 2 ), 106.1º, 106.6º ( 3 ), 105.1º, and 108.2º ( 4 ). Using the molecular parameters of the X-Ray determinations the low temperature (10 K) IR and Raman spectra of the (n-Bu₄N) salts of all four linkage isomers have been assigned by normal coordinate analyses based on a modified valence force field. The valence force constants are f_d(OsN) = 1.71 ( 1 ), 1.46 and 1.62 ( 2 ), 1.69 ( 3 ), and 1.61 ( 4 ), f_d(OsS) = 1.27 ( 2 ), 1.36 ( 3 ), 1.32, and 1.49 mdyn/Å ( 4 ). Taking into account increments of the trans influence a good agreement between observed and calculated frequencies is achieved.     

Darstellung,Kristallstrukturen, Schwingungsspektren und Normalkoordinatenanalyse von vier bindungsisomeren Tetrachlorodirhodanoosmaten(IV)

Preparation, Crystal Structures, Vibrational Spectra, and Normal Coordinate Analysis of Four Linkage Isomeric Tetrachlorodirhodanoosmates(IV) By treatment of cis- or trans-[OsCl₄I₂]^2? with (SCN)₂ in dichloromethane the linkage isomers cis-[OsCl₄(NCS)₂]^2? ( 1 ), trans-[OsCl₄(NCS)(SCN)]^2? ( 2 ), cis-[OsCl₄(NCS)(SCN)]^2? ( 3 ) and trans-[OsCl₄(SCN)₂]^2? ( 4 ) are formed which have been separated by ion exchange chromatography on diethylaminoethyl cellulose. The X-Ray structure determinations on single crystals of cis-(Ph₄As)₂[OsCl₄(NCS)₂] (triclinic, space group P1 , a = 10.019(5), b = 11.702(5), c = 21.922(5) Å, α = 83.602(5)°, β = 85.718(5)°, γ = 73.300(5)°, Z = 2), trans-(Ph₄As)₂[OsCl₄ · (NCS)(SCN)] (monoclinic, space group P2₁/c, a = 18.025(5), b = 11.445(5), c = 23.437(5) Å, β = 94.208(5)°, Z = 4), cis-(Ph₄As)₂[OsCl₄(NCS)(SCN)] (triclinic, space group P1 , a = 10.579(5), b = 11.682(5), c = 22.557(5) Å, α = 81.073(5)°, β = 85.807(5)°, γ = 87.677(5)°, Z = 2) and trans-(Ph₄As)₂ · [OsCl₄(SCN)₂] (triclinic, space group P1 , a = 10.615(5), b = 11.691(5), c = 11.907(5) Å, α = 111.314(5)°, β = 96.718(5)°, γ = 91.446(5)°, Z = 1) reveal the complete ordering of the complex anions. The via N or S coordinated thiocyanate groups are located nearly direct above one of the cis-positioned Cl ligands with Os? N? C angles of 171.2° and 174.3° ( 1 ), 162.3° ( 2 ), 172° ( 3 ) and Os? S? C angles of 108.3° ( 2 ), 105.7° ( 3 ) and 105.5° ( 4 ). Using the molecular parameters of the X-Ray determinations the low temperature (10 K) IR and Raman spectra of the (n-Bu₄N) salts of all four linkage isomers are assigned by normal coordinate analyses based on a modified valence force field. The valence force constants are f_d(OsN) = 1.59 ( 1 ), 1.67 ( 2 ), 1.60 ( 3 ) and f_d(OsS) = 1.27 ( 2 ), 1.31 ( 3 ) and 1.32 mdyn Å^?1 ( 4 ). Taking into account increments of the trans influence a good agreement between observed and calculated frequencies is achieved.     

Comparative Thermogravimetric Studies of Poly(ether-ketone/sulfone) Imides and Their Parent Polymers: I. Poly(ether-ketone/sulfone) ethylimide

Thermogravimetry (TG) was employed to study the thermal degradation kinetics of poly(etherketone/sulfone)ethylimide (PEK-IE and PES-IE). The corresponding decomposition activation energies and reaction orders were obtained and the comparison was made with their parent polymerspoly(ether-ketone/sulfone) with Cardo group (PEK-C and PES-C). The results show that the degradation activation energies of PEK-IE and PES-IE were lower than that of PEK-C and PES-C; and two stages of the degradation process were found for all the four polymers. For PEK-IE and PES-IE, the activation energies in the first decomposition stage are much lower than that in the second stage and the two stages can be taken as slow induction and fast degradation, whereas for PEK-C and PES-C the activation energies in the first decomposition stage are larger than that in the second stage, and the two stages can both be taken as two fast degradation stages. The decomposition mechanism of the two stages was also speculated.This revised version was published online in November 2005 with corrections to the Cover Date.     

Darstellung und Kristallstruktur von (n-Bu4N)3[Ir(NCS)(SCN)5]

Preparation and Crystal Structure of (n-Bu₄N)₃[Ir(NCS)(SCN)₅] The evaporated ethanolic extrakt of the reaction product of K₃[IrCl₆] and HNO₃, refluxed with an aqueous KSCN solution yields a mixture of the linkage isomers [Ir(NCS)_n(SCN)_6?-n]^3?, n = 0? 2, and small amounts of linkage isomeric chloropentarhodanoiridates(III), from which [Ir(NCS)(SCN)₅]^3? has been isolated by ion exchange chromatography on DEAE-cellulose. The X-Ray structure determination on a single crystal of (n-Bu₄N)₃[Ir(NCS)(SCN)₅] (monoclinic, space group P 2₁/a, a = 17.513(5), b = 32.607(5), c = 23.661(5) Å, β = 94.757(5)°, Z = 8) confirms the existance of a heteroleptic hexakis(thiocyanato(N)-thiocyanato(S))iridate(III) with an Ir? N distance of 2.03 Å and Ir? S bond lengths between 2.29 and 2.38 Å. The SCN groups with angles between 166 and 175° are nearly linear with Ir? S? C angles from 99.9 to 109.4°. The Ir? N? C angles of the two crystallographic independent anions are 166 and 174°.     

SYNTHESIS AND CHARACTERIZATION OF METAL COMPLEXES WITH AMPICILLIN

Abstract

The reaction, in water, of Co(II), Ni(II), Cu(II), Zn(II) and Cd(II) ions with sodium ampicillinate at room temperature has allowed isolation of dimers with the following general formula [M(amp)Cl]₂ × nH₂O (n = 1.5?3.2). The complexes were characterized by elemental analyses, conductivity measurements, magnetic susceptibilities and spectroscopic methods (IR, Raman, EPR and UV-Visible). A dinuclear structure based on octahedrally coordinated metal ions is proposed.     

Thermal Degradation of Poly(ε-caprolactone), Poly(L-lactic acid) and their Blends with Poly(3-hydroxy-butyrate) Studied by TGA/FT-IR Spectroscopy

Summary: The thermal degradation behavior of poly(ε-caprolactone) (PCL) and poly(L-lactic acid) (PLA) have been studied in different environment. It was found that these polymers undergo completely different degradation processes in nitrogen and oxygen atmosphere. In oxygen environment PCL and PLA mainly decompose to CO₂, CO, water and short-chain acids. In nitrogen atmosphere PCL releases 5-hexenioc acid, CO₂, CO and ε-caprolactone, whereas PLA decomposes to acetaldehyde, CO₂, CO and lactide. The polymer blends of poly(3-hydroxybutyrate) (PHB) with PCL and PLA decompose similar to the individual homopolymers with crotonic acid as the initial decomposition product of PHB.     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性;均苯四甲酸二酐;联苯四羧酸二酐;二羟基联苯胺;聚酰亚胺;聚苯并噁唑;耐热性     

Energy relationship and the polarization of C_(60) cage in the endohedral complexes (X@C_(60))

In this paper, we carry out the calculation on the system (X@C60)(X=Li, Na, K, Kb, Cs; F, Cl, Br, I), where the position of X changes along 5 typical symmetry directions. For the calculation of quantum chemistry we use EHMO/ASED method, for the calculation of molecular mechanics we use Buckingham potential (exp-6-1) function, and for the calculation of thermo-chemical cycle we use individually isolating the processes such as the structure variation, charge transfer and charge distribution, and their interactions etc. The calculation results show that (1) In the region of radius r≈0.2 nm of the Ceo cage, the potential field is nearly spherical; (2) Except for Li and Na, the systems are the most stable with minimum energies at the center of C60 cage. For Li and Na, the systems are the most stable with minimum energies at r≈0.16 nm and r≈0.13 nm, respectively. In view of the interactive region of chemical bonds, the interactions between X and the C60 cage do not belong to the classical chemical bonds; (     

铜在3%NaCl溶液中腐蚀行为的光电化学研究

Cu以其优异的导电性、导热性和易加工性广泛用于工农业生产中．自然Cu的腐蚀和防腐成为人们很关注的问题．人们已经注意到，Cl-对Cu的腐蚀有影响，并进行过一些研究．但目前使用光电化学方法研究这一问题的文章尚不多见，特别是利用测量开路光电压及其瞬态波形这一现场的、无损的、灵敏的监测方法研究户对Cu电极腐蚀全过程的文章尚未见到．本文正是利用如上方法及XPS，AES方法，研究了Cl-对Cu电极腐蚀的全过程，取得了一些有意义的结果．1实验方法Cu电极用99．99％（质量分数）的Cu制成，面积约为39mm2；电极底部由Cu导线焊接引出，…     

On the morphological behavior of ABC miktoarm stars containing poly(cis 1,4-isoprene), poly(styrene), and poly(2-vinylpyridine)

Fundamental understanding of microphase separation in ABC miktoarm copolymers is vital to access a plethora of nonconventional morphologies. Miktoarm stars based on poly(cis 1,4-isoprene) (I), poly(styrene) (S), and poly(2-vinylpyridine) (V) are model systems, which allow systematic studies of the effects of composition, chemical microstructure, and temperature on the thermodynamics of microphase separation. Eleven ISV-x (I:S:V = 1:1:x, v:v:v) miktoarm copolymers were synthesized by anionic polymerization affording well-defined copolymers with a variable V arm. Equilibrium bulk morphologies of all samples, as evidenced by small-angle X-ray scattering, transmission electron microscopy (TEM), and self-consistent field theory, showed a systematic transition from lamellae (x ≈ 0–0.2) to [8.8.4] tiling (x ≈ 0.6–0.9) to cylinders in undulating lamellae (x ≈ 2–4) and, finally, to hexagonally packed core–shell cylinders (x ≈ 5–8). Chemical microstructure of the I arm [poly(cis 1,4-isoprene)] versus poly(3,4-isoprene) is shown to play important role in affecting morphological behavior. To reconcile differences between ISV-x star morphologies reported in the literature and those reported herein, even for the same composition, effects of the microstructure of I arm on the Flory–Huggins parameter between I and V arms were taken into account in a qualitative manner. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1491–1504