大负载超声振动磨削系统的设计

设计了一种大负载超声振动磨削系统,超声系统由换能器、圆柱圆锥形变幅杆和轮辐式砂轮组成.首先将轮辐式砂轮等效成轮毂为圆柱杆、辐板与轮缘为中厚板的复合模型,利用各接触面边界连续的条件推导系统的频率方程,完成了超声磨削系统的设计,制作了实验装置并分析验证了其声学振动特性.实验结果表明:利用轮辐式砂轮复合模型求解系统频率方程,...     

阵列式压电振子超声复合喷丸强化*

为了进一步改善超声喷丸强化质量,提升工件表面残余应力和显微硬度的均匀性,对压电振子阵列型超声喷丸强化加工系统进行了改进,提出了在强化加工过程中辅助工件往复运动的方法。对改进后的压电振子阵列型超声喷丸强化加工原理进行了阐述,分析了激振片的振动特性并进行了结构尺寸优化,应用Abaqus对工件往复运动下超声喷丸强化过程进行了仿真研究,分析了在不同的工件往复运动频率下,工件表面残余应力分布情况。实验测试了在不同喷丸强化时间及工件往复运动频率下超声喷丸强化加工质量,探究了喷丸时间和工件往复运动频率对工件表面显微硬度的影响。结果表明：在压电振子阵列型超声喷丸强化过程中辅助工件往返运动,可以有效提高工件表面残余应力和显微硬度分布的均匀性,工件表面强化质量得到提升。     

超声波雾化铝表面液滴的试验研究

介绍了一种超声波抑霜新方法。对频率20 kHz的超声波作用下铝表面液滴的雾化现象进行了可视化观测。对不同超声输入功率以及不同超声作用时间下,70 mm×70 mm×3 mm铝表面液滴群的雾化概率进行了分析。试验结果发现,超声波可以瞬间雾化铝板表面液滴;随着超声输入功率的增加,铝表面液滴雾化概率逐渐增加;功率越低,超声作用时间对液滴雾化概率的影响越显著。结果表明,超声波可以去除铝板表面作为结霜初始阶段的液滴,为冷表面有效抑霜提供了可能。     

液体推进剂模拟工质在离心喷嘴内流动特性研究

设计了一种双旋流槽离心式喷嘴,采用高速录像系统,研究了液体推进剂模拟工质在喷口处的雾化角特性。在实验基础上,建市r离心式喷嘴内流的VOF模型,基于FLUENT软件进行了数值模拟,获得了喷嘴内流场密度、速度分布特性。结果表明：喷雾初期喷嘴内存在一个空气核,随后很快消失,雾化角变小并趋于稳定。雾化角计算值与测量值吻合较好。     

双铂网雾化和超声雾化进样系统对ICP-AES分析性能的影响

从元素检出限、基体效应、ICP稳健性及记忆效应方面实验研究了双铂网雾化与超声雾化两种进样方式对ICP-AES分析性能的影响。结果表明,在超声雾化进样条件下,Cu,Pb,Zn,Cr,Cd,Ni的检出限较双铂网雾化的检出限降低了6～23倍;在基体效应方面,超声雾化进样时基体对元素原子及离子谱线强度的影响均较双铂网雾化系统明显,元素谱线增强/减弱的幅度受元素谱线、基体组成和浓度的影响;Ca和Mg基体对谱线强度的影响强于K和Na基体;离子谱线受基体的影响明显强于原子谱线。超声雾化系统进样时ICP的稳健性要劣于双铂网雾化系统,而且超声雾化系统的记忆效应较双铂网雾化器严重。     

弱酸试纸法测量功率超声珩磨空化声场的研究*

为了简便、直观地测量功率超声珩磨磨削区的空化声场强度及分布情况,提出了利用弱酸PH试纸测量磨削区空化声场的方法。利用超声空化效应产生的弱酸空化泡在PH试纸表面溃灭后,形成深浅和分布不同的变色区域,间接地表征油石表面空化声场的强弱和分布规律。通过对比不同超声频率、测试距离和时间,得出了最佳测试距离和时间。结果表明,当超声频率为18.6 kHz,距离为10 mm时,测得油石表面的空化声场强度和分布最佳。该方法可形象地评价功率超声珩磨磨削区空化声场的强度和分布情况,具有一定的实际应用价值。     

带有锥形孔的复合变幅杆设计及动态分析

在超声振动拉丝加工过程中,为了实现线材的顺利拉拔,需要应用带有锥形孔的复合变幅杆。为此,本文基于等效四端网络与传输矩阵法,建立了带锥形孔圆锥变幅杆的传输矩阵,推导出带锥形孔圆锥过渡复合变幅杆的频率方程的一般公式。根据推导出的频率方程,应用区间搜索法和牛顿迭代法获取了准确的数值解,实现了该复合变幅杆的纵向振动。之后,应用有限元软件Ansys对设计出的复合变幅杆分别进行模态分析和动力学特性分析,获得了各段不同长度下复合变幅杆谐振频率、放大系数以及最大应力值的变化规律。最后,对制造出的复合变幅杆进行阻抗与振动性能测试,结果表明其频率准确,且振幅比较稳定。     

脆性光学材料的超声磨削实验研究

分别采用超声磨削和普通磨削加工方法加工了几种脆性光学材料,研究了几种主要工艺参数对工件加工表面粗糙度的影响。结果表明,超声频率和振幅、金刚石磨料粒度、切深、工具的横向进给速度和旋转速度等工艺参数对表面粗糙度的影响较大。通过比较发现,超声磨削方法比普通磨削方法具有更好的加工表面粗糙度,更高的材料去除率,以及更低的工具磨损量。     

超声辅助磨削杯形砂轮变幅器设计与试验*

超声辅助磨削在硬脆材料的加工中应用广泛。为研制以杯形砂轮为加工工具的超声辅助磨削主轴附件式工具系统,建立了杯形砂轮变幅器的理论模型,推导了其频率方程,并通过Matlab开发了杯形砂轮变幅器设计软件。利用该软件结合有限元分析对杯形砂轮变幅器进行了设计。将研制的杯形砂轮变幅器与BT40刀柄一体化外套筒、导电滑环装配组成了杯形砂轮超声辅助磨削主轴附件式工具系统。对该超声振动系统进行了阻抗分析试验及超声谐振试验,结果表明,该超声振动系统阻抗性能较好,能够使杯形砂轮产生稳定的超声振动,验证了所提出的设计方法的正确性,为主轴附件式超声磨削装置的设计提供了理论参考。     

面向水下应用的电容式微机械超声换能器*

电容式微机械超声换能器具有宽频带和易于制造二维阵列等优势,已经成为一种重要的新型超声换能器。该文针对图像声呐系统对新型超声换能器的迫切需求,提出了一种电容式微机械超声换能器结构和参数,并利用硅微加工技术制备出了该换能器,最后对其主要性能参数进行了测试和分析。测试结果表明该换能器具有发射和接收超声波的功能,中心工作频率为1.965 MHz,6 dB相对带宽达到109.4%,在1 MHz、2 MHz和3 MHz频率时的接收灵敏度分别为-218.29 d B、-219.39 dB和-218.11 dB。该文研制的电容式微机械超声换能器显示出了优秀的宽频带特性,且工作频率和接收灵敏度性能均基本满足了高频图像声呐系统的需求。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.