Carbon Microsphere-Supported Metallic Nickel Nanoparticles as Novel Heterogeneous Catalysts and Their Application for the Reduction of Nitrophenol

Nickel nanoparticles are gaining increasing attention in catalysis due to their versatile catalytic action. A novel, low-cost and facile method was developed in this work to synthesize carbon microsphere-supported metallic nickel nanoparticles (Ni-NP/C) for heterogeneous catalysis. The synthesis was based on carbonizing a polystyrene-based cation exchange resin loaded with nickel ions at temperatures between 500 and 1000 °C. The decomposition of the nickel-organic framework resulted in both Ni-NP and carbon microsphere formation. The phase composition, morphology and surface area of these Ni-NP/C microspheres were characterized by powder X-ray diffraction, Raman spectroscopy, scanning electron microscopy and BET analysis. Elemental nickel was found to be the only metal containing phase; fcc-Ni coexisted with hcp-Ni at carbonization temperatures between 500 and 700 °C, and fcc-Ni was the only metallic phase at 800–1000 °C. Graphitization and carbon nanotube formation were observed at high temperatures. The catalytic activity of Ni-NP/C was tested in the reduction of 4-nitrophenol to 4-aminophenol by sodium borohydride, and Ni-NP/C was proved to be an efficient catalyst in this reaction. The relatively easy and scalable synthetic method, as well as the easy separation and catalytic activity of Ni-NP/C, provide a viable alternative to existing nickel nanocatalysts in future applications.     

Application of TOF-SIMS Method in the Study of Wetting the Iron (111) Surface with Promoter Oxides

In the present work, a simplified model of the Fe(111) surface’s promoter-oxide system was investigated in order to experimentally verify the previously proposed and known models concerning the structure and chemical composition of the surfaces of iron nanocrystallites in the ammonia-synthesis catalyst. It was shown that efficient oxygen diffusion from metal oxides to the clean Fe(111) iron surface took place even at temperatures lower than 100 °C. The effective wetting of the iron surface by potassium oxide is possible when the surface is covered with oxygen at temperatures above 250 °C. In the TOF-SIMS spectra of the surface of iron wetted with potassium, an emission of secondary FeOK⁺ ions was observed that implies that potassium atoms are bound to the iron surface atoms through oxygen. As a result of further wetting the iron surface with potassium ions, a heterogeneous surface structure was formed consisting of a thin K₂O layer, next to which there was an iron-oxide phase covered with potassium ions. Only a limited increase in calcium concentration was observed on the Fe(111) iron surface upon sample annealing at up to 350 °C. As a result of wetting the iron surface with calcium ions, an oxide solution of CaO-Fe_xO_y was formed. In the annealing process of the sample containing alumina, only traces of this promoter diffusing to the iron surface were observed. Alumina formed a solution with a passive layer on the iron surface and under the process conditions (350 °C) it did not wet the pure iron (111) surface. The decrease in Fe⁺-ion emission from the Fe-Ca and Fe-Al samples at 350 °C implies a reduction in the oxygen concentration on the sample surface at this temperature.     

Low temperature methanation of CO2 over an amorphous cobalt-based catalyst

CO₂ methanation is an important reaction in CO₂ valorization. Because of the high kinetic barriers, the reaction usually needs to proceed at higher temperature (>300 °C). High-efficiency CO₂ methanation at low temperature (<200 °C) is an interesting topic, and only several noble metal catalysts were reported to achieve this goal. Currently, design of cheap metal catalysts that can effectively accelerate this reaction at low temperature is still a challenge. In this work, we found that the amorphous Co–Zr_0.1–B–O catalyst could catalyze the reaction at above 140 °C. The activity of the catalyst at 180 °C reached 10.7 mmol_CO2 g_cat⁻¹ h⁻¹, which is comparable to or even higher than that of some noble metal catalysts under similar conditions. The Zr promoter in this work had the highest promoting factor to date among the catalysts for CO₂ methanation. As far as we know, this is the first report of an amorphous transition metal catalyst that could effectively accelerate CO₂ methanation. The outstanding performance of the catalyst could be ascribed to two aspects. The amorphous nature of the catalyst offered abundant surface defects and intrinsic active sites. On the other hand, the Zr promoter could enlarge the surface area of the catalyst, enrich the Co atoms on the catalyst surface, and tune the valence state of the atoms at the catalyst surface. The reaction mechanism was proposed based on the control experiments.

It is discovered that an amorphous transition metal catalyst Co–Zr0.1–B–O could effectively accelerate CO2 methanation, at a rate that is comparable to or even higher than that of some noble metal catalysts under similar conditions.     

The Quenching and Sonication Effect on the Mechanical Strength of Silver Nanowires Synthesized Using the Polyol Method

This study aims to determine the effect of fast cooling (quenching) on thermal properties, mechanical strength, morphology and size of the AgNWs. The synthesis of AgNWs was carried out at three different quenching-medium temperatures as follows: at 27 °C (ambient temperature), 0 °C (on ice), and −80 °C (in dry ice) using the polyol method at 130 °C. Furthermore, the AgNWs were sonified for 45 min to determine their mechanical strength. Scanning electron microscopy analysis showed that the quenched AgNWs had decreased significantly; at 27 °C, the AgNWs experienced a change in length from (40 ± 10) to (21 ± 6) µm, at 0 °C from (37 ± 8) to (24 ± 8) µm, and at −80 °C from (34 ± 9) to (29 ± 1) µm. The opposite occurred for their diameter with an increased quenching temperature: at 27 °C from (200 ± 10) to (210 ± 10) nm, at 0 °C from (224 ± 4) to (239 ± 8) nm, and at −80 °C from (253 ± 6) to (270 ± 10) nm. The lower the temperature of the quenching medium, the shorter the length and the higher the mechanical strength of AgNWs. The UV-Vis spectra of the AgNWs showed peak absorbances at 350 and 411 to 425 nm. Thermogravimetric analysis showed that AgNWs quenched at −80 °C have better thermal stability as their mass loss was only 2.88%, while at the quenching temperatures of 27 °C and 0 °C the mass loss was of 8.73% and 4.17%, respectively. The resulting AgNWs will then be applied to manufacture transparent conductive electrodes (TCEs) for optoelectronic applications.     

Ranolazine-functionalized CuO NPs: efficient homogeneous and heterogeneous catalysts for reduction of 4-nitrophenol

In the present study copper oxide nanoparticles (CuO NPs) were synthesized using a hydrothermal method with ranolazine as a shape-directing agent. Ranolazine-functionalized CuO NPs were characterized by various analytical techniques such as scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD). The SEM pattern confirmed the morphology of ranolazine-functionalized CuO NPs with well-defined rice-like structures. FTIR spectroscopy confirmed the interaction between CuO NPs and ranolazine. The XRD analysis indicated that the structure of ranolazine-functionalized CuO NPs was monoclinic crystalline and the size ranged between 9 and 18 nm with an average particle size of 12 nm. The smaller size range of CuO NPs gave a large surface area that enhanced the efficiency of these catalysts employed for the reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) in the H ₂ O system. In homogeneous catalysis, results showed that 50 μL of CuO NPs was required in the presence of NaBH4 for 99% reduction of 4-NP in 240 s. On the other hand, for heterogeneous catalysis, 0.5 mg of CuO NPs was used in the presence of NaBH4 for 99% catalytic reduction of 4-NP to 4-AP in 320 s. The rate of reaction for homogeneous catalysis and heterogeneous catalysis was determined from the plots of In(Ct /C0) of 4-NP versus time (s), which showed good linearity with values of 1.3 × 10 ^-2 and 8.8 × 10 ^-3 s ^-1 . respectively. The high-quality catalytic efficiency, good reusability, nontoxic nature, and low cost are favorable properties of the synthesized CuO NPs for use as efficient catalysts for reduction of 4-AP to 4-NP in both homogeneous and heterogeneous media.     

Effect of TiO2 Calcination Pretreatment on the Performance of Pt/TiO2 Catalyst for CO Oxidation

In order to improve the CO catalytic oxidation performance of a Pt/TiO₂ catalyst, a series of Pt/TiO₂ catalysts were prepared via an impregnation method in this study, and various characterization methods were used to explore the effect of TiO₂ calcination pretreatment on the CO catalytic oxidation performance of the catalysts. The results revealed that Pt/TiO₂ (700 °C) prepared by TiO₂ after calcination pretreatment at 700 °C exhibits a superior CO oxidation activity at low temperatures. After calcination pretreatment, the catalyst exhibited a suitable specific surface area and pore structure, which is beneficial to the diffusion of reactants and reaction products. At the same time, the proportion of adsorbed oxygen on the catalyst surface was increased, which promoted the oxidation of CO. After calcination pretreatment, the adsorption capacity of the catalyst for CO and CO₂ decreased, which was beneficial for the simultaneous inhibition of the CO self-poisoning of Pt sites. In addition, the Pt species exhibited a higher degree of dispersion and a smaller particle size, thereby increasing the CO oxidation activity of the Pt/TiO₂ (700 °C) catalyst.     

The Effects of Prolonged Storage on ARPE-19 Cells Stored at Three Different Storage Temperatures

This study aimed to investigate how prolonged storage of adult retinal pigment epithelial (ARPE-19) cell sheets affects cell metabolism, morphology, viability, and phenotype. ARPE-19 cell sheets were stored at three temperatures (4 °C, 16 °C, and 37 °C) for three weeks. Metabolic status and morphology of the cells were monitored by sampling medium and examining cells by phase-contrast microscopy, respectively, throughout the storage period. Cell viability was analyzed by flow cytometry, and phenotype was determined by epifluorescence microscopy after the storage. Lactate production and glucose consumption increased heavily, while pH dropped considerably, through storage at 37 °C compared to 4 °C and 16 °C. During storage, morphology started to deteriorate first at 4 °C, then at 37 °C, and was maintained the longest at 16 °C. Viability of the cells after three weeks of storage was best preserved at 16 °C, while cells stored at 4 °C and 37 °C had reduced viability. Dedifferentiation indicated by reduced expression of retinal pigment epithelium-specific protein 65 (RPE65), zonula occludens protein 1 (ZO-1), and occludin after three weeks of storage was noticed in all experimental groups compared to control. We conclude that storage temperature affects the metabolic status of ARPE-19 cells and that 16 °C reduces metabolic activity while protecting viability and morphology.     

Highly Sensitive and Selective Eco-Toxic 4-Nitrophenol Chemical Sensor Based on Ag-Doped ZnO Nanoflowers Decorated with Nanosheets

Herein, we have developed a novel sensing electrode to detect the eco-toxic 4-nitrophenol (4-NP). Ag-doped-ZnO nanoflowers were synthesized by facile hydrothermal method and examined by several characterization techniques in order to understand the morphology, crystal structure, composition, and surface properties. Morphological results were confirmed by the formation of Ag-doped ZnO nanoflowers decorated with nanosheets. Ag-doped ZnO/glassy carbon electrode (GCE) electrode-material-matrix was used for electrochemical sensing of toxic 4-NP. Under optimized conditions, Ag-doped ZnO/GCE modified electrode exhibits high-sensitivity and selectivity compared to the bare GCE electrode. The Ag-doped ZnO/GCE modified electrode exhibits high electrocatalytic oxidation towards 4-NP. Anodic peak current of 4-NP is increased linearly by increasing the concentration of nitrophenol. Additionally, Ag-doped ZnO/GCE shows a wide range of sensitivity from 10 µM to 500 µM, and a linear calibration plot with a good detection limit of 3 µM (S/N = 3). The proposed Ag-doped ZnO/GCE modified electrode showed high sensing stability. In addition, the oxidation mechanism was studied. The obtained results revealed that the Ag-ZnO/GCE electrode could be the promising sensing electrode for 4-NP sensing.     

The effect of H2O on the sulfation of Havelock limestone under oxy-fuel conditions in a thermogravimetric analyser

A gas mixture representing oxy-fuel combustion conditions was employed in a thermogravimetric analyser to determine the effect of water vapor and SO₂ concentration on limestone sulfation kinetics over the temperature range of 800 to 920 °C. Here, experiments used small samples of particles (4 mg), with small particle sizes (d_p < 38 µm) and large gas flow rates (120 mL/min@NTP) in order to minimize mass transfer interferences. The gas mixture contained 5000 ppm_v SO₂, 2% O₂, and the H₂O content was changed from 0% to 25% with the balance CO₂. When water vapor was added to the gas mixture at lower temperatures (800–870 °C), the limestone SO₂ capture efficiency increased. However, as the temperature became higher, the enhancement in total conversion values decreased. As expected, Havelock limestone at higher temperatures (890 °C, 920 °C, and 950 °C) experienced indirect sulfation and reacted at a faster rate than for lower temperatures (800–870 °C) for direct sulfation over the first five minutes of reaction time. However, the total conversion of Havelock limestone for direct sulfation was generally greater than for indirect sulfation.     

Influence of Carbon Nanotubes on Phase Composition,Thermal and Post-Heating Behavior of Cementitious Composites

This paper experimentally investigates the influence of carbon nanotubes (CNTs) on phase composition, microstructure deterioration, thermal behavior, and residual mechanical strengths of cementitious composites exposed to elevated temperatures. Cement mortars with small dosages of CNTs, 0.05% and 0.2% by weight of cement, were prepared and then heated at 25 °C, 150 °C, 200 °C, 450 °C, and 600 °C for two hours before being tested. The results show positive impact of the CNTs on the hydration process of cement mortar at room temperature and at higher temperatures up to 200 °C. Decomposition of the hydration products is obvious at 450 °C, whereas sever deterioration in the microstructure occurs at 600 °C. The nano reinforcement and bridging effect of the CNTs are obvious up to 450 °C. Thermal behavior characterization shows that CNTs incorporation enhances the thermal conductivity of the unheated and heat-treated mortar specimens. The decomposition of the hydration products needs more heat in the presence of CNTs. Finally, presence of CNTs significantly enhances the residual compressive and flexural strengths of heated mortar specimens for all studied temperatures.     

Effect of Heat Exposure on Activity Degradation of Enzymes in Mango Varieties Sindri,SB Chaunsa,and Tommy Atkins during Drying

Mango has been described as a valuable source of nutrients and enzymes that are beneficial to human health. Drying at different temperatures not only affects the nutritional properties but can also contribute to the degradation of valuable enzymes in dried fruit. The novelty of this paper is to investigate the quality of hot air dried mango in terms of activity retention of the heat-sensitive enzymes (HSE). For this, HSE was first screened in fresh mango flesh of the variety Samar Bahisht (SB) Chaunsa. Later, the combined effect of different drying temperatures (40 °C, 50 °C, 60 °C, 70 °C, and 80 °C) and air velocities (1.0 ms⁻¹ and 1.4 ms⁻¹) on the activity retention of HSE in dried mango slices of the varieties Sindri, SB Chaunsa, and Tommy Atkins were investigated. The results showed that the drying temperature had a significant impact on the degradation of HSE, while at the same time some influence of the air velocity was also observed. Drying at 40 °C and an air velocity of 1.4 ms⁻¹ retained more HSE compared to those samples dried at higher temperatures. The least retention of HSE was found in samples dried at 80 °C.     

Concentration Dependent Catalytic Activity of Glutathione Coated Silver Nanoparticles for the Reduction of 4-Nitrophenol and Organic Dyes

In the present study, we have synthesized glutathione modified silver nanoparticles (GSH-AgNPs) in aqueous medium and are characterized by absorption, high resolution transmission electron microscope (HR-TEM), selective area electron diffraction (SAED) pattern, dynamic light scattering (DLS), Zeta potential and Fourier transform infrared (FT-IR) spectroscopic measurements. Catalytic activity of GSH-AgNPs has been evaluated for the reduction reactions of 4-nitrophenol (4-NP), methylene blue (MB dye) and eosin Y (EY dye) in presence of sodium borohydride including the effect of catalyst concentration on the catalytic activity. Furthermore, the rate constants of reduction reactions are determined, which are linearly enhanced upon increasing the concentrations of GSH-AgNPs. It is explored that reduction reactions such as 4-NP, organic dyes by NaBH₄ in the presence of catalyst follow a pseudo first order kinetics. The catalytic reduction of 4-NP and organic dyes proceed with a faster rate even in the presence of nanomolar concentration of catalyst.     

Migration Testing of GPPS and HIPS Polymers: Swelling Effect Caused by Food Simulants Compared to Real Foods

Migration kinetic data from general purpose polystyrene (GPPS) and high impact polystyrene (HIPS) were generated for a set of model substances as well as styrene monomer and oligomers at different temperatures (20 °C, 40 °C, 60 °C) using food simulants stipulated in the European Regulation (EU) 10/2011 and real foods like milk, cream and olive oil (20 °C, 40 °C). The extent of polymer swelling was characterized gravimetrically and visual changes of the test specimens after migration contact were recorded. Isooctane and 95% ethanol caused strong swelling and visual changes of HIPS, overestimating real migration into foods especially at high temperatures; GPPS was affected by isooctane only at 60 °C. With 50% ethanol, after 10 days contact at 60 °C or 40 °C both polymers were slightly swollen. Contrary, most of the real foods analyzed caused no detectable swelling or visual changes of the investigated polymers. This study demonstrates that the recommendations provided by EU regulations are not always in agreement with the physicochemical properties of styrenic polymers. The critical point remains the selection of adequate food simulants/testing conditions, since the high overestimation of aggressive media can lead to non-compliance of polystyrene materials even if the migration into real food would be of no concern.     

Temperature and Inoculum Origin Influence the Performance of Ex-Situ Biological Hydrogen Methanation

The conversion of H₂ into methane can be carried out by microorganisms in a process so-called biomethanation. In ex-situ biomethanation H₂ and CO₂ gas are exogenous to the system. One of the main limitations of the biomethanation process is the low gas-liquid transfer rate and solubility of H₂ which are strongly influenced by the temperature. Hydrogenotrophic methanogens that are responsible for the biomethanation reaction are also very sensitive to temperature variations. The aim of this work was to evaluate the impact of temperature on batch biomethanation process in mixed culture. The performances of mesophilic and thermophilic inocula were assessed at 4 temperatures (24, 35, 55 and 65 °C). A negative impact of the low temperature (24 °C) was observed on microbial kinetics. Although methane production rate was higher at 55 and 65 °C (respectively 290 ± 55 and 309 ± 109 mL CH₄/L.day for the mesophilic inoculum) than at 24 and 35 °C (respectively 156 ± 41 and 253 ± 51 mL CH₄/L.day), the instability of the system substantially increased, likely because of a strong dominance of only Methanothermobacter species. Considering the maximal methane production rates and their stability all along the experiments, an optimal temperature range of 35 °C or 55 °C is recommended to operate ex-situ biomethanation process.     

Accelerated and Natural Aging of Cellulose-Based Paper: Py-GC/MS Method

Samples of papers artificially (2 to 60 days) and naturally (10, 45, and 56 years) aged were studied by the Py-GC/MS method to identify decomposition products. Possible reaction scenarios for cellulose degradation were developed. One of the degradation products is acetic acid, which can (auto)catalyze the cleavage of cellulose β(1→4)-glycosidic bonds of cellulose polymer chains. However, during 20 s of Py-GC/MS analysis, temperatures of up to 300 °C did not significantly increase or modify the formation of decomposition products of paper components. At 300 °C, the amount of several cellulose decomposition products increased regularly depending on the number of days of artificial aging and natural aging, demonstrated mainly by the generation of 2-furancarboxaldehyde, 5-hydroxymethylfurfural, and levoglucosan and its consecutive dehydration products. No correlation between the amount of lignin decomposition products and the time of aging was found when the pyrolysis was performed at 300 °C and 500 °C. Compounds present in the products of decomposition at 500 °C bear the imprint of the chemical composition of the sampled paper. Pyrograms taken at 300 °C using the Py-GC/MS method can give additional information on the changes in the chemical structure of paper during natural or artificial aging, mainly about the cleavage of β(1→4)-glycosidic bonds during aging.     

Hydrodechlorination of 4-Chlorophenol on Pd-Fe Catalysts on Mesoporous ZrO2SiO2 Support

A mesoporous support based on silica and zirconia (ZS) was used to prepare monometallic 1 wt% Pd/ZS, 10 wt% Fe/ZS, and bimetallic FePd/ZS catalysts. The catalysts were characterized by TPR-H₂, XRD, SEM-EDS, TEM, AAS, and DRIFT spectroscopy of adsorbed CO after H₂ reduction in situ and tested in hydrodechlorination of environmental pollutant 4-chlorophelol in aqueous solution at 30 °C. The bimetallic catalyst demonstrated an excellent activity, selectivity to phenol and stability in 10 consecutive runs. FePd/ZS has exceptional reducibility due to the high dispersion of palladium and strong interaction between FeOx and palladium, confirmed by TPR-H₂, DRIFT spectroscopy, XRD, and TEM. Its reduction occurs during short-time treatment with hydrogen in an aqueous solution at RT. The Pd/ZS was more resistant to reduction but can be activated by aqueous phenol solution and H₂. The study by DRIFT spectroscopy of CO adsorbed on Pd/ZS reduced in harsh (H₂, 330 °C), medium (H₂, 200 °C) and mild conditions (H₂ + aqueous solution of phenol) helped to identify the reasons of the reducing action of phenol solution. It was found that phenol provided fast transformation of Pd⁺ to Pd⁰. Pd/ZS also can serve as an active and stable catalyst for 4-PhCl transformation to phenol after proper reduction.     

A Study of the Effect of Sintering Conditions of Mg0.95Ni0.05Ti3 on Its Physical and Dielectric Properties

Mg_0.95Ni_0.05TiO₃ ceramics were prepared by traditional solid-state route using sintering temperatures between 1300 and 1425 °C and holding time of 2–8 h. The sintered samples were characterized for their phase composition, micro-crystalline structure, unit–cell constant, and dielectric properties. A two-phase combination region was identified over the entire compositional range. The effect of sintering conditions was analyzed for various properties. Both permittivity (ε_r) and Q factor (Q_f) were sensitive to sintering temperatures and holding times, and the optimum performance was found at 1350 °C withholding time of 4 h. The temperature coefficient of resonant frequency (τ_f) in a range from −45.2 to −52 (ppm/°C) and unit–cell constant were not sensitive to both the sintering temperature and holding time. An optimized Q factor of 192,000 (GHz) related with a permittivity (ε_r) of 17.35 and a temperature coefficient (τ_f) of −47 (ppm/°C) was realized for the specimen sintered at 1350 °C withholding time of 4 h. For applications of 5G communication device (filter, antennas, etc.), Mg_0.95Ni_0.05TiO₃ is considered to be a suitable candidate for substrate materials.     

Nanostructured gold colloid electrode based on in situ functionalized self-assembled monolayers on gold electrode

A novel method for fabricating nanostructured gold colloid electrode based on in situ functionalization of self-assembled monolayers (SAMs) of 4-aminothiophenol (4-ATP) on gold electrode is proposed. The in situ functionalization of 4-ATP SAMs yields a redox active monolayer of 4′-mercapto-N-phenylquinone diimine (NPQD). When the amino-rich surface is exposed to gold colloid, the citrate-stabilized gold nanoparticles (GNPs) can be anchored onto the surface of the in situ functionalized electrode by the electrostatic interactions and a new nanostructured gold colloid surface was obtained. The mixed monolayers of in situ functionalized product, NPQD, and 1,4-benzenedimethanethiol (BDMT) can provide a more compact and order platform to fabricate GNPs on the electrode surface. The film formed by this technique has the advantages of high organization and uniformity, which could provide a desirable microenvironment to assemble GNPs and facilitate the concentration of the analyte from the bulk solution to the electrode surface. The nanostructured gold colloid electrode has favorable effect on the electrochemical oxidation of naphthol isomers.     

Combined Effect of Impregnation with an Origanum vulgare Infusion and Osmotic Treatment on the Shelf Life and Quality of Chilled Chicken Fillets

The scope of this work is the study of a combined process including a dipping step into an oregano (Origanum vulgare ssp. hirtum) infusion (OV) followed by osmotic treatment of chicken fillets at 15 °C. Chicken fillets were immersed in an osmotic solution consisting of 40% glycerol and 5% NaCl with (OV/OD) and without (OD) prior antioxidant enrichment in a hypotonic oregano solution. A comparative shelf life study of all the samples (untreated, OD and OV/OD treated) was then conducted at 4 °C in order to assess the impact of this process on the quality and shelf life of chilled chicken fillets. Microbial growth, lipid oxidation and color/texture changes were measured throughout the chilled storage period. Rates of microbial growth of pretreated fillets were significantly reduced, mainly as a result of water activity decrease (OD step). Rancidity development closely related to off odors and sensory rejection was greatly inhibited in treated fillets owing to both inhibitory factors (OD and OV), with water-soluble phenols (OV step) exhibiting the main antioxidant effect. Shelf life of treated chicken fillets exhibited a more than three-fold increase as compared to the untreated samples based on both chemical and microbial spoilage indices, maintaining a positive and pleasant sensory profile throughout the storage period examined.     

Physicochemical Properties and Antioxidant Activity of Spray-Dry Broccoli (Brassica oleracea var Italica) Stalk and Floret Juice Powders

This research presents the microencapsulation and conservation of antioxidants of broccoli juice processed by spray drying, and proposes the use of a by-product as a technological application. Broccoli juice (BJ) extracted from two sources, stalks and florets, was spray-dried employing maltodextrin (MX) as a carrier agent at concentrations of 5, 7.5, and 10%, and inlet temperatures of 150 and 220 °C. The total phenolic content (TPC), and antioxidant activity (AA) of the BJ-MX powders were determined together with the physicochemical characteristics, including particle morphology, microstructure, and thermal properties. Based on the TPC and AA, the optimal processing conditions found were 5% of MX and a drying temperature of 220 °C. However, the florets showed higher TPC, while stalks presented higher AA under those processing conditions. The particles exhibited micrometric sizes and a mixture of spherical-shape particles and pseudo-spherical particles. The diffractograms indicated an amorphous microstructure in all samples. The glass transition temperature (Tg) was determined in the range of 50 °C for the samples dried at 150 °C and 55 °C for those dried at 220 °C. This suggested that powders might be stored at temperatures below the Tg without presenting any loss of antioxidants.