Phosphate materials for cathodes in lithium ion secondary batteries

Olivine phosphates of general formula LiMPO₄ (M=Fe, Co, Ni) were prepared and characterised in order to evaluate new potential cathode materials for secondary lithium ion batteries. The synthesis was performed by soft chemistry methods to avoid problematical and energetic expensive solid state reactions. In all the compounds no secondary phase was detected and the powder morphology was found to be suitable for cathode layers preparation. Only LiFePO₄ and LiCoPO₄ showed reversible lithium deintercalation-intercalation at 3.5 and 4.8 V vs. Li⁺/Li, respectively. The LiCoPO₄ high potential makes this compound very attractive for high energy batteries, but unfortunately its lifetime appears to be too poor. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14 – 18, 2004.     

Two-phase reaction mechanism during chemical lithium insertion into α-MoO<Subscript>3</Subscript>

The phase transition during chemical lithium insertion into α-MoO₃ was investigated by chemical analysis, X-ray diffraction (XRD) and electrochemical characterisation. The samples have been prepared by reaction of various amounts of water-free lithium iodide with fine-particulate orthorhombic molybdenum trioxide in n-hexane (non-aqueous media), which yielded materials with different Li/Mo ratio. XRD investigations of these materials proved that the crystal structure of the layered α-MoO₃ has been changed after the chemical lithiation. The phase transition ranged from 0.25 < x < 0.5 in Li _x MoO₃ upon chemical lithium insertion into α-MoO₃. The XRD lines of lithium inserted phase Li _x MoO₃ grew at the expense of the XRD lines of the pristine α-MoO₃ as lithium ions were chemically inserted until the disappearance of lines related to α-MoO₃. The electrochemical performance of the lithiated samples is improved in comparison with the starting material (non-lithiated α-MoO₃).     

Progress in the lithium insertion mechanism in Cu3P

Copper phosphide, Cu₃P has been synthesized using a ceramic route, and its electrochemical behaviour versus lithium has been studied studied galvanostatic and potentiodynamic measurements and in situ X-ray diffraction analysis. The insertion/extraction mechanism proceeds with the formation of at least three different Li_xCu_3−xP (x=1, 2, 3) phases. The electrochemical behaviour of Cu₃P samples obtained from ceramic and solvothermal syntheses are compared to further understanding of the complex redox mechanism occurring during insertion/extraction. First-principle electronic structure calculations show that discharge probably begins with the formation of a solid solution Li_xCu_3−yP (x<0.5). Paper presented at the Patras Conference on Solid State Ionics-Transport Properties, Patras, Greece, Sept. 14 – 18, 2004.     

Synthesis and characterization of pristine Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript> and Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript>/C cathode materials for lithium ion batteries

The cathode materials, pristine Li₂MnSiO₄ and carbon-coated Li₂MnSiO₄ (Li₂MnSiO₄/C), were synthesized by the sol–gel method. Power X-ray diffraction and scanning electron microscopy analyses show that the presence of carbon during synthesis can weaken the formation of impurities in the final product and decrease the particle size of the final product. The effects of carbon coating on electrochemical characteristics were investigated by galvanostatic cycling test and electrochemical impedance spectroscopy. The galvanostatic cycling test results indicate that Li₂MnSiO₄/C cathode exhibits better electrochemical performance with an initial discharge capacity of 134.4 mAh g⁻¹ and a capacity retention of 63.9 mAh g⁻¹ after 20 cycles. Electrochemical impedance analyses confirm that carbon coating can increase electronic conductivity, which results in good electrochemical performance of Li₂MnSiO₄/C cathode. The two semicircles and the large arc obtained in this study can be attributed to the migration of lithium ions through the solid electrolyte interphase films, the electronic properties of the material, and the charge transfer step, respectively.     

First-principles study of high pressure phase transformations in Li<Subscript>3</Subscript>N

The lattice dynamics of lithium nitride (Li₃N) under high pressure are extensively investigated to probe its phase transformations by using the pseudopotential plane-wave method within the density functional theory. A new second order α↦α^′-Li₃N phase transition is identified for the first time. The newly proposed α^′-phase possesses a hexagonal symmetry with four ions in the unit cell having a space group of P-3m1. Further enthalpy and phonon calculations support the existence of this phase, which stabilizes in a narrow pressure range of 2.8 – 3.6 GPa at zero temperature. Upon further compression, transitions to denser packed phases of β-and γ-Li₃N are typical first order. The analysis of the electronic densities of states suggests that all the high pressure modifications of Li₃N are insulators and, interestingly, the typical behavior of compression is to broaden the band gap.     

Effect of stresses on the OH libration bands in proton-exchanged LiNbO3 optical waveguides

i -H_xLi_1-xNbO₃ phases generated on x-cut LiNbO₃ the new anisotropic libration mode at 890–940 cm^-1 is observed in addition to the known isotropic mode at 960–970 cm^-1, whereas the same phases on z-cut exhibit only latter isotropic libration mode. The observed phenomena are explained as a result of anisotropic stresses generated in the x-cut waveguides, whereas the stresses in the structures on z-cut are isotropic. The OH-bond librations are clearly anisotropic in the α, κ₁, and κ₂ phases generated on both z- and x-cuts, which indicates a fundamental difference of the local symmetry of the proton’s position in the β_i phases compared to the α, κ₁, and κ₂ H_xLi_1-xNbO₃ phases. Received: 4 May 1998/Revised version: 26 June 1998     

Improvement of lithium battery performance through composite electrode microstructure optimization

The lithium trivanadate Li_1.2V₃O₈ has been investigated during the past decade as a very promising positive electrode material for lithium batteries due to its high theoretical capacity of 360 mAh/g. However, the experimental capacity remains generally much lower than (about half) the theoretical value. To increase electrode cycling performance in batteries, most researchers generally focus their work on the active material optimisation. Here we show that the polymeric binder of the composite electrode may have an important role on the electrode performance. We describe a new tailored polymeric binder combination with controlled polymer-filler (carbon black) interactions that allows the preparation of new and more efficient electrode architecture. Using this polymeric binder, composite electrodes based on Li_1.2V₃O₈ display a room-temperature cycling capacity of 280 mAh/g (C/5 rate, 3.3-2V) instead of 180 mAh/g using a Bellcore-type composite electrode (PLIon^TM technology). We have coupled SEM observations, galvanostatic cycling and electrochemical impedance spectroscopy in order to define and understand the impact of the microstructure of the composite electrode on its electrochemical performance. Derived from these studies, the main key factors that provide efficient charge carrier collection within the composite electrode complex medium will be discussed. Present findings open up new and attractive prospects for electrode performance optimisation. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14–18, 2004.     

Mechanosynthesis and characterisation of the Li–Sn system

Intermetallic phases Li–Sn were synthesized by ball-milling and characterized for their structures and electrochemical performances. All phases in Li–Sn binary phase diagram were identified by ¹¹⁹Sn Mössbauer spectroscopy, used as reference materials for the study of lithium insertion into tin-based electrode materials. The observed spectra show two distinct environments of tin; the Sn-rich phases and the Li-rich phases. An example of electrochemical properties of these phases is proposed for Li₂₂Sn₅. Irreversibility of the first cycle is related to the structural change (3D→2D) of this phase.     

Determination of proton diffusion in solid electrolytes

Two electrochemical methods have been used to determine the proton diffusion in solid electrolytes. One is based on transient ionic current measurements and a reasonable physical model; the other one is a quick determination using steady-state transport. The results of proton diffusion coefficients of 10⁻⁶ and 10⁻⁵ cm²/s obtained for the α- and β-phases of Li₂SO₄, respectively, using these two methods are in a good agreement with published results. The methods turned out to be very useful for determining proton diffusion in solid electrolytes, especially when the electrolytes contain more than one type of the mobile ionic species and a low concentration of the protons. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

Preparation and characterization of spherical La-doped Li4Ti5O12 anode material for lithium ion batteries

The lithium secondary batteries with high power density need the electrode materials with both high specific capacity and high tap density. An “outer gel” method by TiCl₄ as the raw material has been developed to prepare spherical precursor. High tap density spherical Li₄Ti₅O₁₂ is synthesized by sintering the mixture of precursor and Li₂CO₃. La-doped Li₄Ti₅O₁₂ is also prepared by this method. X-ray diffraction, scanning electron microscopy, energy-dispersive spectrometry, tap density testing, and the determination of the electrochemical properties show that the Li₄Ti₅O₁₂ powders prepared by this method are spherical and exhibits high tap density. La³⁺ dopant improved the electrochemical performance over the pristine Li₄Ti₅O₁₂. It is tested that the tap density of the pristine and La³⁺-doped products is as high as 1.80 and 1.78 g•cm⁻³, respectively. Between 1.0 and 3.0 V versus Li, the initial discharge capacity of the La³⁺ dopant is as high as 161.5 mAh•g⁻¹ at 0.1C rate. After 50 cycles, the reversible capacity is still 135.4 mAh•g⁻¹.     

Structural and electrochemical study on Li(Li1/3Ti5/3)O4 anode material for lithium ion batteries

Chemical and electrochemical studies have shown that various titanium oxides can incorporate lithium in different ratios. Other compounds with a spinel-type structure and corresponding to the spinel oxides LiTi₂O₄ and Li₄Ti₅O₁₂ have been evaluated in rechargeable lithium cells with promising features. The spinel Li[Li_1/3Ti_5/3]O₄ [1–5] compound is a very appealing electrode material for lithium ion batteries. The lithium insertion-deinsertion process occurs with a minimal variation of the cubic unit cell and this assures high stability which may reflect into long cyclability. In addition, the diffusion coefficient of lithium is of the order of 10⁻⁸ cm²s⁻¹ [5] and this suggests fast kinetics which may reflect in high power capabilities. In this work we report a study on the kinetics and the structural properties of the Li[Li_1/3Ti_5/3]O₄ intercalation electrode carried out by: cyclic voltammetry, galvanostatic cycling and in-situ X-ray diffraction. The electrochemical characterization shows that the Li[Li_1/3Ti_5/3]O₄ electrode cycles around 1.56 V vs. Li with a capacity of the order of 130 mAhg⁻¹ which approaches the maximum value of 175 mAhg⁻¹ corresponding to the insertion of 1 equivalent per formula unit. The delivered capacity remains constant for hundred cycles confirming the stability of the host structure upon the repeated Li insertion-deinsertion process. This high structural stability has been confirmed by in situ Energy Dispersion X-ray analysis. Paper presented at the 7th Euroconference on Ionics, Calcatoggio, Corsica, France, Oct. 1–7, 2000.     

A novel approach to employ Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript> as anode active material for lithium batteries

In the present paper, we describe utilization of cathode active material as anode active material, for example, Li₂MnSiO₄. The lithium manganese silicate has been successfully synthesized by solid-state reaction method. The X-ray diffraction pattern confirms the orthorhombic structure with Pmn2 ₁ space group. The Li/Li₂MnSiO₄ cell delivered the initial discharge capacity of 420 mA h g⁻¹, which is 110 mA h g⁻¹ higher than graphitic anodes. The electrochemical reversibility and solid electrolyte interface formation of the Li₂MnSiO₄ electrode was emphasized by cyclic voltammetry.     

Electrochemical properties and structures of the mixed-valence lithium cuprates Li3Cu2O4 and Li2NaCu2O4

The electrochemical performances of Li₃Cu₂O₄ and Li₂NaCu₂O₄ as cathode materials in lithium coin type batteries have been studied. In Li₃Cu₂O₄, the copper was oxidised to the III level when cycling. The replacement of the lithium by the sodium ions in the octahedral sites in Li₂NaCu₂O₄ might have an effect on the pathway of the lithium ions during the (de)intercalations. Paper presented at the 7th Euroconference on Ionics, Calcatoggio, Corsica, France, Oct. 1–7, 2000.     

Ceramics for fusion reactors: The role of the lithium orthosilicate as breeder

Lithium-based oxide ceramics are studied as breeder blanket materials for the controlled thermonuclear reactors (CTR). Lithium orthosilicate (Li₄SiO₄) is one of the most promising candidates because of its lithium concentration (0.54 g/cm³), its high melting temperature (1523 K) and its excellent tritium release behavior. It is reported that the diffusion of tritium is closely related to that of lithium, so it is possible to find an indirect measure of the trend of tritium studying the diffusivity of Li⁺.     

A study of formation of solid ionic conductors in the mixed system (CdI2)b[(Ag2O)·(CrO3)]100-b (20≤b≤80)

Using Wagner's polarization technique and EMF method the joinic and silver ionic transport number measurements of various compositions of the mixed system CdI₂-Ag₂O-CrO₃ have been made. The presence of AgI in these materials has been inferred from the typical β → α phase transition of AgI, which is characterized by an endothermic peak at around 420 K in the DSC traces of these specimens. While the structural analysis performed by means of powder X-ray diffraction has revealed the formation of ionic phases involving polycrystalline compounds, the Fourier transform infrared (FTIR) spectroscopic results have indicated the presence of ionic species thus confirming the ionic nature of the products. The complex impedance studies carried out in the frequency range 20 Hz - 1 MHz and over the temperature range 294 – 442 K have revealed that the best conducting composition, namely 55%(CdI₂) – 45%(Ag₂O·CrO₃), would exhibit a silver ionic conductivity of 1.3×10⁻⁵Scm⁻¹ at 294 K.     

Ionic conduction and chemical bonds of Li ion in La4/3−yLi3yTi2O6

The electronic state of La_4/3−yLi_3yTi₂O₆ (y=0.21) was studied by the DV-Xα cluster method. Four model clusters were used to calculate the density of state (DOS), the bond overlap population (BOP) and the net charge (NC). A Li ion in the model cluster was moved from 1b site to another 1b site along the x axis, and the BOP and the NC calculated were discussed. Furthermore, we calculated the potential energy with the movement of the Li ion along the x axis. Paper presented at the Patras Conference on Solid State Ionics - Transport Properties, Patras, Greece, Sept. 14 – 18, 2004.     

Superlinear photovoltaic currents in proton-exchanged LiNbO<Subscript>3</Subscript> waveguides

Photovoltaic currents along the c axis have been measured in α-phase LiNbO₃ proton-exchanged waveguides at several visible wavelengths for a guided-beam configuration. The light-intensity dependence is superlinear and all experimental curves are very well fitted by computer simulations using a two-centre model, with Fe²⁺/Fe³⁺ as primary and Nb_Li ⁴⁺/Nb_Li ⁵⁺ as secondary photovoltaic centres. The superlinear behaviour arises from a much higher effective photovoltaic length of Nb_Li ⁴⁺ (small polaron) compared with that of Fe²⁺. In β₁-phase guides, the photocurrents are much smaller than in α-phase guides and apparently do not show superlinear behaviour. Received: 22 October 2002 / Revised version: 6 January 2003 / Published online: 12 May 2003 RID="*" ID="*"Corresponding author. Fax: +34-91/3978-579, E-mail: m.carrascosa@uam.es     

Bi4Cu0.2V1.8 O11–δ based membrane electrochemical reactors for propane oxidation at moderate temperaturesbased membrane electrochemical reactors for propane oxidation at moderate temperatures

Bi₄Cu_0.2V_1.8O_11–δ membrane material was synthesized by following the solid-state method. The oxygen permeation flux at 673 K was found to be 0.5 ml/cm² by the use of an external electric power source. The oxidation of propane was selected as the probe reaction using the Bi₄Cu_0.2V_1.8O_11–δ electrochemical membrane reactor. It was found that such electrochemical membrane reactors could have potential application in the area of alkanes selective oxidation at moderate temperatures. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14–18, 2004.     

Preparation and characterization of spinel Li4Ti5O12 nanoparticles anode materials for lithium ion battery

Spinel Li₄Ti₅O₁₂ nanoparticles were prepared via a high-temperature solid-state reaction by adding the prepared cellulose to an aqueous dispersion of lithium salts and titanium dioxide. The precursors of Li₄Ti₅O₁₂ were characterized by thermogravimetry and differential scanning calorimetry. The obtained Li₄Ti₅O₁₂ nanoparticles were characterized using X-ray diffraction, transmission electron microscopy (TEM) and electrochemical measurements. The TEM revealed that the Li₄Ti₅O₁₂ prepared with cellulose is composed of nanoparticles with an average particle diameter of 20–30 nm. Galvanostatic battery testing showed that nano-sized Li₄Ti₅O₁₂ exhibit better electrochemical properties than submicro-sized Li₄Ti₅O₁₂ do especially at high current rates, which can deliver a reversible discharge capacity of 131 mAh g⁻¹ at the rate of 10 C, whereas that of the submicro-sized sample decreases to 25 mAh g⁻¹ at the same rate (10 C). Its reversible capacity is maintained at ~172.2 mAh g⁻¹ with the voltage range 1.0–3.0 V (vs. Li) at the current rate of 0.5 C for over 80 cycles.     

Ball milling synthesis of LixTiP4: Improvement of the electrochemical performances

While promising performance as a negative electrode in Li-ion batteries, with flat voltage profiles at about 1 V and large specific capacities, today’s drawback with Li_xTiP₄ materials is the difficulty encountered in preparing single-phase powders. To alleviate this issue, new synthetic routes have been investigated and we present here our results obtained by ball milling (BM) syntheses. Despite the poor crystallinity of the as prepared BM powders demonstrated by both X-rays and electron diffractions, preliminary electrochemical tests have shown a dramatic improvement of the specific capacity and charging-discharging rate confirming the advantages of BM synthesis over the high temperature route. To divert any amorphous phases contamination by amorphous phases contamination, BM samples were annealed at 500 °C and 900 °C. Nicely crystallized samples devoid of any impurities are obtained. We also detail in this paper the improvement in cyclability of these annealed BM Li_xTiP₄ electrode materials. Paper presented at the 9th EuroConference on Ionics, Ixia, Rhodes, Greece, Sept. 15–21, 2002.