TS-1/过氧化氢催化体系中有机硫化物的选择氧化

 研究了TS-1/过氧化氢催化体系中几种典型有机硫化物的选择氧化脱除. 结果表明,噻吩和2-甲基噻吩仅在水或叔丁醇溶剂中才能被有效氧化脱除,且两者的反应历程不同. 噻吩分子中的硫原子先被氧化,2-甲基噻吩分子中的噻吩环先被氧化. 当过氧化氢与硫化物摩尔比为4时,噻吩和2-甲基噻吩均可被氧化为硫酸. 采用甲醇、乙腈和水作溶剂时,甲基硫醚和丁基硫醇均可被选择氧化脱除. 由于存在空间位阻,苯并噻吩、二苯并噻吩及4,6-二甲基二苯并噻吩在TS-1/过氧化氢体系中均不能被有效脱除.     

Ti-HMS催化氧化脱除模拟燃料中的硫化物

 将噻吩、苯并噻吩、二苯并噻吩和4,6-二甲基二苯并噻吩(DMDBT)分别溶于正辛烷配成模拟燃料,以Ti-HMS为催化剂,以H2O2为氧化剂,对模拟燃料的氧化脱硫进行了研究,考察了Ti-HMS的催化活性及硅/钛比和结晶度对催化剂活性的影响. 结果表明,在Ti-HMS上硫化物氧化的难易顺序是由噻吩环上硫原子的电子云密度和硫化物分子的空间位阻共同决定的; 氧化反应发生在分子筛孔道内,骨架钛原子为活性中心; DMDBT在Ti-HMS上的氧化脱除效果比在TS-1,Ti-β或Ti-MCM-41上好. 随着Ti-HMS中硅/钛比的增大,DMDBT的脱除率降低; 随着Ti-HMS分子筛结晶度的升高,DMDBT的脱除率升高.     

Ti-MWW催化烯丙基氯环氧化高效合成环氧氯丙烷

 研究了具有MWW结构的新一代钛硅分子筛Ti-MWW催化剂对烯丙基氯液相环氧化高效合成环氧氯丙烷的催化性能. 结果表明, Ti-MWW的催化活性以及产物选择性均优于传统的钛硅分子筛TS-1. 对于Ti-MWW,合适的溶剂为非质子性溶剂丙酮和乙腈,在该溶剂中环氧化物不易发生溶剂化开环反应; 而对于TS-1,合适的溶剂是质子性溶剂甲醇,但甲醇可导致醇醚副产物的生成. 在Ti-MWW催化剂上烯丙基氯的转化率和环氧氯丙烷的选择性都能达到99%以上.     

无机钛硅原料合成TS-1催化氯丙烯环氧化反应

采用无机钛硅原料体系合成出了TS-1分子筛,并对TS-1分子筛催化氯丙烯环氧化反应进行了研究.在以甲醇为溶剂的体系中考察了反应时间、反应温度、催化剂用量、氯丙烯与双氧水的摩尔比对反应的影响,得到了无机钛硅原料体系合成的TS-1催化氯丙烯环氧化反应的最优条件:反应时间为60 min,反应温度为45℃,催化剂用量为22.5 g L-1,氯丙烯与双氧水的摩尔比n(AC):n(H2O2)=1.8,并对无机钛硅原料体系合成的TS-1进行了修饰改性,评价了其催化性能.     

合成条件对TS-1结构及其催化氯丙烯环氧化的影响

采用水热法合成了TS-1分子筛，根据XRD、FT-IR、FT-Raman和UV-Vis的表征结果计算了TS-1的相对结晶度和骨架钛相对含量，并以氯丙烯环氧化反应为探针反应，研究了合成条件对TS-1的结构和催化性能的影响，结果表明，TS-1的结晶度随合成液中Si／Ti比和TPAOH／Si比的增大呈先增大后减小的趋势，TS-1的骨架钛相对含量也随合成液中钛含量的减少呈先增大后减小的趋势，随TPAOH含量的增加TS-1的骨架钛相对含量和非骨架钛含量一直增加，且非骨架钛的类型有所改变．具有较高结晶度和骨架钛含量及较低非骨架钛含量的TS-1的催化性能较好．较好的氯丙烯的转化率和环氧氯丙烷的选择性分别为92．1％和87．5％．     

钛硅分子筛TS-1的酸性表征及酸催化性能

采用Hammett指示剂滴定法表征了钛硅沸石TS-1的酸性.结果表明,TS-1酸强度范围为+3.3相似文献   

干胶法制备钛硅沸石及其催化性能

以四丙基溴化铵为模板剂,以乙二胺(EDA)为碱源,采用干胶法制备了TS-1,并在此基础上引入介孔/大孔模板剂蔗糖而制备出多级孔道TS-1.采用X射线衍射、紫外-可见光谱及N2物理吸附-脱附等手段对所得样品进行了表征,并考察了它们催化噻吩(Th)及苯并噻吩(BT)氧化反应的性能.结果表明,随着釜底部n(EDA)/n(H2O)比的降低,TS-1结晶度、骨架Ti含量及其在Th氧化反应中的催化活性均升高.而当以乙胺和正丁胺为碱源时,TS-1难以晶化.所制备的多级孔道TS-1样品具有介孔/大孔孔道,在Th氧化反应中的催化活性高于TS-1;对于BT的氧化,当n(sucrose)/n(SiO2)为0.35时,制备的多级孔道TS-1样品的催化活性最高,BT脱除率可达100%,而TS-1则无催化活性.     

Ti-HMS和TS-1分子筛结构和催化性能的对比研究

 采用长链十二烷基胺为模板剂,成功合成出含钛中孔分子筛Ti-HMS, 并针对其晶化过程、结构特征以及催化性能与修正经典法制备的微孔分子筛TS-1进行了对比. 结果表明,中孔分子筛Ti-HMS的晶化机理不同于微孔分子筛TS-1的晶化机理. 随着晶化温度的提高, Ti-HMS分子筛的相对结晶度降低,且晶化过程中母液的pH值变化不大. TEM照片显示, Ti-HMS分子筛的孔壁整体上呈无定形,在局部区域可能存在晶态或者类晶态物种. 与TS-1分子筛相比, Ti-HMS分子筛的活性中心(骨架钛)处在畸变的四面体环境中. 中孔分子筛Ti-HMS可以满足大分子硫化物(如苯并噻吩)氧化反应的要求; 对于小分子硫化物(如噻吩)的氧化反应,微孔分子筛TS-1催化剂效果更好.     

氨基酸辅助合成高活性六配位钛物种的TS-1分子筛

TS-1分子筛是以TO4(T=Si,Ti)四面体为基本单元,通过氧桥连接而形成的具有MFI拓扑结构的微孔晶体材料,其在催化烯烃环氧化、酮类氨肟化、氧化脱硫及芳香烃羟基化等氧化反应中表现出较好的催化活性.目前,提高TS-1分子筛催化性能的方法主要包括:(1)制备纳米和多级孔TS-1分子筛,以提高其扩散传质性能;(2)提高TS-1分子筛的钛含量并抑制锐钛矿相的产生,以增加其催化活性位点.最新研究表明,相比于传统四配位钛物种(TiO4)作为催化活性中心,六配位(TiO6)钛物种在烯烃环氧化反应中具有更高的催化活性,可进一步降低反应活化能,最终实现高效催化转化.然而,TiO6物种结构中的Ti-OH组分,易导致开环反应发生,从而降低环氧化产物的选择性.因此,构筑高活性TiO6物种及调变TiO4/TiO6比例,对提高烯烃转化率及环氧产物选择性具有重要意义.当前,高活性钛物种的结构表征及其构筑已成为研究热点且仍面临挑战.本文协同采用氨基酸辅助合成策略和两步晶化方法,成功地制备出具有TiO4和TiO6物种且无锐钛矿相的多级孔TS-1分子筛.在该协同策略中,两步晶化过程有利于抑制锐钛矿相的形成,而氨基酸的引入对高活性TiO6物种的构筑具有重要作用.氨基酸分子可与钛原料形成螯合物,为TS-1分子筛晶化提供"养料",并有效平衡晶体成核与生长速率及稳定TiO6物种,最终实现制备富含TiO6物种的多级孔TS-1分子筛.相比于传统TiO4物种作为催化活性中心(1-己烯的转化率<25％,环氧化产物选择性>95％),本文所制备的TS-1分子筛(Si/Ti=36.9)因其兼具TiO4和TiO6物种,在1-己烯环氧化反应中表现出更好的催化性能(1-己烯的转化率33％,环氧化产物选择性95％).这是由于TiO4物种不会导致开环反应的发生,因此可以保证较高的环氧产物选择性,而TiO6物种经H2O2活化后,可形成具有更高活性及更小位阻效应的催化中心,极大提高了1-己烯转化率.综上,本文合成策略为构筑具有高活性钛物种及多级孔结构的钛硅分子筛提供了指导作用,为调控硅铝酸盐及硅取代磷酸铝分子筛材料活性位点的含量和分布提供了新思路.     

叔丁醇溶剂中TS-1催化丙烯环氧化的动力学研究

研究了叔丁醇溶剂中TS-1催化丙烯环氧化反应的本征动力学，反应条件为:温度303.15K～323.15K，丙稀压力0.3 MPa～0.6 MPa。根据反应机理及组分在TS-1上的吸附特点建立了如下的机理模型方程式： 根据实验数据，我们对机理模型进行了参数估值。检验结果表明拟合效果较好，反应符合Eley-Rideal机理，丙烯环氧化反应发生在吸附态的过氧化氢与游离态的丙烯之间。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.