新型DNA电化学传感器的研制及其用于DNA氧化性损伤检测的研究

用溶胶-凝胶法在玻碳电极上制备了纳米多孔羟基磷灰石(HAp)-聚乙烯醇(PVA)涂层膜固定双链DNA,得到了一种新型DNA电化学传感器,检测了由Fenton反应引起的DNA氧化性损伤.结果表明,一定量浓度的抗坏血酸(AA)能加速Fenton反应的进行,使DNA损伤很快达到极限;损伤试剂中Fe²⁺的浓度越大,产生的羟基自由基(OH.)越多,对DNA的损伤就越严重;损伤试剂中EDTA的浓度越小,溶液中游离的Fe²⁺以及与DNA键合的Fe²⁺的浓度则相对越大,对DNA的损伤也就越严重.     

基于纳米ZnO/壳聚糖复合膜DNA电化学传感器用于HIV基因的免标记检测

以室温固相合成法制备纳米ZnO,通过壳聚糖(CHIT)的成膜效应将纳米ZnO固定在玻碳电极(GCE)表面,制得的ZnO/CHIT/GCE电极成为DNA固定和杂交的良好平台。DNA的固定和杂交通过电化学交流阻抗进行表征。以电化学交流阻抗免标记法检测目标DNA,固定于电极表面的DNA探针与目标DNA杂交后使电极表面的电子传递电阻增大,以此作为检测信号可以高灵敏度地测定目标DNA。电化学阻抗谱检测人类免疫缺陷病毒(HIV)基因片段的线性范围为2.0×10-11~2.0×10-6mol/L,检出限为2.0×10-12mol/L。     

用于DNA杂交检测的丝网印刷型生物传感器的研究

将单链DNA(ssDNA)固定到丝网印刷碳电极上构成电化学DNA传感器,采用电化学指示剂,建立DNA杂交的检测方法.Co(phen)33+电化学指示剂通过钴盐与配体邻菲罗啉络合制备,采用等离子发射光谱法(ICP-AES)和核磁共振法(NMR)表征功能基团,采用循环伏安法(CV)分析指示剂的电化学特性,并以此为基础研究ssDNA在电极表面的固定及DNA杂交过程.本研究探讨了直接吸附、静电吸附与键合等3种ssD-NA在电极表面的固定方法,结果表明,静电吸附法和键合法具有较高的ssDNA固定量,采用静电吸附法固定探针的电极杂交目标DNA后,Co(phen)33+易于嵌入双链DNA (dsDNA)中,CV峰电流(ip)信号随目标DNA浓度增加.本研究采用静电吸附ssDNA的电极检测DNA杂交,实验表明,当探针固定液中ssDNA浓度为5 mg/L时,目标DNA浓度在6.65×10- 8～4.26× 10-6mol/L范围内,Co(phen)33+在dsDNA修饰电极上ip值与DNA浓度呈良好的线性关系,R2为0.9819.本研究为建立新的微生物分子分型手段提供了初步依据.     

快速检测Fenton反应诱导DNA损伤的电化学DNA传感器研究

利用带正电荷的聚二甲基二烯丙基氯化铵(PDDA)和带负电荷的小牛胸腺双链DNA(CT-dsDNA)之间的静电吸引作用,将其层层组装到玻碳电极表面,制成电化学DNA传感器,并利用电化学和原子力显微镜(AFM)方法与对DNA的组装进行了表征。以Ru(bpy)23+作为电化学催化剂,检测DNA的损伤,考察了电极在Fenton试剂中的温育时间以及Fenton试剂的浓度对DNA损伤程度的影响。实验表明,Fe2+与H2O2共存时,温育15 min即可较大程度地对DNA造成损伤,且可以检测到的Fenton试剂浓度为5.0×10"5mol/L Fe-SO4/2.0×10"4mol/L H2O2。本方法具有灵敏度高、重现性好等优点。     

柔红霉素修饰的纳米金电极的制备及其对DNA检测

利用双硫醇分子作为连接剂, 将纳米金颗粒固定于金电极上, 用伏安法、紫外-可见光谱和电化学交流阻抗对其组装过程以及活性进行了表征. 制备的纳米金修饰电极用于DNA测定及其对DNA损伤的检测. DNA的检测限为 1.2×10^－9 mol/L. 该法灵敏、简便.     

基于DNA四面体纳米结构探针的电化学生物传感器检测DNA甲基化

该文以DNA四面体纳米结构探针(TSP)为捕获探针,将辣根过氧化物酶标记的IgG抗体结合在纳米金颗粒表面(AuNPs-IgG-HRP)作为信号分子,构建了一种新型DNA甲基化电化学传感器。利用一步热变性法组装成TSP后,通过Au—S键固定在修饰纳米金颗粒的金电极表面,经过靶标DNA杂交、5-甲基胞嘧啶(5-mc)抗体及AuNPs-IgG-HRP结合后,用差分脉冲伏安法(DPV)进行检测。采用循环伏安法(CV)和电化学阻抗谱(EIS)对修饰电极的构建过程进行电化学表征。探究了杂交时间、5-mc抗体浓度、IgG-HRP加入体积、氢醌(HQ)和过氧化氢(H2O2)浓度对传感器的影响。在最佳条件下,该传感器对甲基化DNA的线性响应范围为1.0×10-15~1.0×10-10 mol/L,检出限(S/N=3)为4.4×10-16 mol/L。该传感器具有良好的选择性和稳定性,为DNA甲基化检测提供了新方法。     

DNA在Mg/聚2,6-吡啶二甲酸膜上的固定和杂交及其PAT基因片段的电化学阻抗谱测定

以静电吸附法使Mg²⁺修饰于玻碳电极(GCE)上电聚合的2,6-吡啶二甲酸膜(PDC)上, 制得的Mg/PDC/GCE电极, 成为DNA固定及杂交的良好平台. 应用微分脉冲伏安法和电化学阻抗谱对DNA的固定和杂交进行表征. 以电化学阻抗谱免标记法检测目标DNA比以亚甲基蓝为指示剂的微分脉冲伏安法有更高的灵敏度. 固定于电极表面的DNA探针与互补单链DNA杂交后使电负性的[Fe(CN)₆]^3-/4-的表面电子传递电阻值显著增大, 以此作为检测信号可以高灵敏度地测定目标DNA. 电化学阻抗谱检测转基因植物外源PAT基因片段, 线性范围为1.0×10^-9 ~ 1.0×10^-5 mol/L, 检测限为3.4×10^-10 mol/L.     

基于切刻内切酶信号放大的电致化学发光DNA生物传感器的研究

利用切刻内切酶的酶切作用实现信号放大,结合量子点高效的电化学发光性能,构建了一种新型电化学发光DNA生物传感器.将捕获探针DNA(c-DNA)通过自组装的方式固定到金电极表面,后与目标DNA(t-DNA)互补杂交形成双链DNA,利用切刻内切酶Nt.BstNBI特异性识别双链上的酶切位点(5'-GAGTC-3'),然后在c-DNA相应的切割位点(识别序列3'端后的4个碱基处)对其进行剪切,释放出目标链,参与下一轮的杂交及酶切,通过目标物的循环利用,实现信号放大.利用N-羟基琥珀酰亚胺(N HS)和1-乙基-3-3-二甲基氨丙基碳化二亚胺(EDC)活化羧基化CdTe量子点表面的羧基,与电极表面残留的c-DNA末端的氨基共价交联,通过测定捕获的量子点的电化学发光信号对目标DNA进行检测.优化后的检测条件为:c-DNA浓度1 μmol/L,杂交时间60 min,Nt.BstNBI浓度0.5 U/μL,酶切反应时间4h.在优化条件下,目标DNA浓度在2.0×10-13～2.0×10-11 mol/L范围内,其对数与电化学发光强度呈线性关系,检出限为7.3×10-14 mol/L.人体血样加标回收率为96.4％～108.0％.     

采用电活性标记物N-(2-乙基-二茂铁)马来酰亚胺检测与表面固定的 一致性双链DNA特异性作用的p53蛋白质

建立了电化学检测表面固定捕获的野生型p53蛋白质的方法. 首先在金电极表面形成巯基化的单链DNA探针/己硫醇(HT)混合自组装膜, 随后巯基化的单链DNA探针与溶液中序列匹配的靶点DNA杂交, 所形成的一致性双链DNA捕获溶液中的野生型p53蛋白质. p53分子表面的半胱氨酸残基采用巯基特异性试剂N-(2-乙基-二茂铁)马来酰亚胺(Fc-Mi)进行衍生. 通过检测二茂铁的电化学信号来指示p53与一致性双链DNA之间的特异性相互作用. p53蛋白质与双链DNA的键合程度取决于双链DNA的序列. 该方法可检测的p53最低浓度为1.33 nmol•L－1.     

三维有序金掺杂纳米TiO_2修饰电极用于抗肿瘤药物与DNA相互作用的研究

利用模板法在氧化铟锡(ITO)电极表面制备了三维有序多孔结构的金掺杂纳米Ti O2薄膜修饰电极(3DOM GTD/ITO),并在此修饰电极上成功固定小牛胸腺DNA(ct DNA),从而构建了一种新型的DNA生物传感器(DNA/3DOM GTD/ITO),并通过透射电镜(TEM)、扫描电镜(SEM)对修饰电极的表面形貌进行表征。采用电化学交流阻抗(EIS)法研究了ct DNA在3DOM GTD/ITO修饰电极表面的固定情况,结果表明,ct DNA已被成功地固定在3DOM GTD/ITO修饰电极表面。采用循环伏安法、微分脉冲伏安法等电化学方法研究了抗肿瘤药物槲皮素(Qu)在3DOM GTD/ITO修饰电极表面的电化学性质及与ct DNA的相互作用。结果表明,Qu在3DOM GTD/ITO修饰电极表面有1对准可逆的氧化还原峰,其氧化还原反应为2电子和2质子的转移过程。Qu可与固定在修饰电极上的ct DNA发生较强的结合作用,其结合常数(K)为3.61×106L/mol。循环伏安实验、紫外-可见吸收光谱、分子荧光光谱、圆二色性光谱均表明Qu与ct DNA之间的相互作用模式为嵌插作用。Qu与ct DNA的碱基结合具有序列选择性,对Qu与聚(d G-d C)及聚(d A-d T)的结合常数进行计算,得到结合常数比K(d G-d C)/K(d A-d T)=3.5,表明Qu与ct DNA发生嵌插作用时更倾向于结合在GC富集区域。     

2-Aminopurine hairpin probes for the detection of ultraviolet-induced DNA damage

Nucleic acid exposure to radiation and chemical insults leads to damage and disease. Thus, detection and understanding DNA damage is important for elucidating molecular mechanisms of disease. However, current methods of DNA damage detection are either time-consuming, destroy the sample, or are too specific to be used for generic detection of damage. In this paper, we develop a fluorescence sensor of 2-aminopurine (2AP), a fluorescent analogue of adenine, incorporated in the loop of a hairpin probe for the quantification of ultraviolet (UV) C-induced nucleic acid damage. Our results show that the selectivity of the 2AP hairpin probe to UV-induced nucleic acid damage is comparable to molecular beacon (MB) probes of DNA damage. The calibration curve for the 2AP hairpin probe shows good linearity (R² = 0.98) with a limit of detection of 17.2 nM. This probe is a simple, fast and economic fluorescence sensor for the quantification of UV-induced damage in DNA.     

Electrochemical Characterization of (ZnO/dsDNA)n Layer-by-layer Films and Detection of Natural DNA Oxidative Damage

The positively charged nano‐ZnO and negatively charged natural DNA were alternately adsorbed on the surface of a gold electrode, forming (ZnO/dsDNA)_nlayer‐by‐layer films. Valuable dynamic information for controlling the formation and growth of the films was obtained by cyclic voltammetry and electrochemical impedance spectroscopy. Differential pulse voltammetric (DPV) measurements showed that the electroactive probe methylene blue (MB) could be loaded in the (ZnO/dsDNA)_nfilms from its solution, and then released from the films into Britton‐Robinson (B‐R) buffer. The complete reloading of MB in the films could be realized by immersing the films in MB solution again. However, after incubation in the solution of carcinogenic metal nickel, the damaged (ZnO/dsDNA)_n films could not return to their original and fully‐loaded state, and showed smaller DPV peak currents. The results demonstrated that the DNA damage induced by the hydroxyl radical could be achieved by electrochemistry.     

Impedance‐Based DNA Biosensor Employing Molecular Beacon DNA as Probe and Thionine as Charge Neutralizer

In this paper, we present an impedance‐based DNA biosensor using thionine intercalation to amplify DNA hybridization signal. Beacon single‐stranded DNA (ssDNA) probe and mercaptoacetic acid were self‐assembled onto a Au electrode by forming Au? S bonds. These beacon ssDNAs were hybridized with the complementary sequences around the loop structure. Then thionine was intercalated into the double‐stranded DNA (dsDNA) immobilized on the Au electrode surface. Due to the neutralization of the negative charges of dsDNA by the intercalated thionine, the electronic transfer resistance (R_et) of the DNA modified Au electrode was significantly diminished. Herein, the decreased value of R_et resulted from the thionine intercalating into dsDNA was employed as the hybridization signal. SDS was used to reduce the unspecific adsorption between ssDNA and thionine. Several experimental conditions, including the surface coverage of ssDNA probe on Au electrode, the hybridization temperature and time were all optimized. Moreover, the hybridization reactions of the unstructured linear ssDNA probe and the structured beacon ssDNA probe with their complementary sequences were compared in this work. The sensitivity of the presented DNA biosensor highlighted that the intercalation of thionine into dsDNA was an efficient approach to amplify the hybridization signal using impedance detection technique. Additionally, in this DNA biosensing protocol, beacon ssDNA has a good ability to distinguish target DNA sequences. This results in a higher specificity than using traditional unstructured DNA probe.     

Designs of Enterobacteriaceae Lac Z Gene DNA Gold Screen Printed Biosensors

This paper describes specific electrochemical enterobacteriaceae lac Z gene DNA sensors based on immobilization of a thiolated 25 base single stranded probe onto disposable screen printed gold electrodes (gold SPEs). Two configurations have been evaluated. In the first one, the capture probe was attached to the electrode surface through its ? SH moiety, while mercaptohexanol (MCH) was used as spacer for the displacement of nonspecifically adsorbed oligonucleotide molecules. The hybridization event between the probe and target DNA sequences was detected at ?0.20 V by square‐wave voltammetry (SWV), using methylene blue (MB) as electrochemical indicator. The second genosensor configuration involved modification of gold high temperature SPEs with a 3,3′‐dithiodipropionic acid di(N‐succinimidyl ester) (DTSP) self‐assembled monolayer (SAM). Moreover, 2‐aminoethanol was used as blocking agent, and further modification with avidin allowed binding of the biotinylated enterobacteriaceae lac Z gene DNA probe. An enzyme amplified detection scheme was applied, based on the coupling of streptavidin‐peroxidase to the biotinylated complementary target, after the hybridization process, and immobilization of tetrathiafulvalene (TTF) as redox mediator atop the modified electrode. The amperometric response obtained at ?0.15 V after the addition of hydrogen peroxide was used to detect the hybridization process. Experimental variables concerning sensors composition and electrochemical transduction were evaluated in both cases. A better precision and reproducibility in the fabrication process, as well as a higher sensitivity were achieved using the biotinylated probe‐based sensor configuration. A limit of detection of 0.002 ng/μL was obtained without any preconcentration step.     

Fabrication of a Sensitive Impedance Biosensor of DNA Hybridization Based on Gold Nanoparticles Modified Gold Electrode

In this work, we report on the preparation of a simple, sensitive DNA impedance sensor. Firstly gold nanoparticles were electrodeposited on the surface of a gold electrode, and then probe DNA was immobilized on the surface of gold nanoparticles through a 5′‐thiol‐linker. Electrochemical impedance spectroscopy (EIS) was used to investigate probe DNA immobilization and hybridization. Compared to the bare gold electrode, the gold nanoparticles modified electrode could improve the density of probe DNA attachment and the sensitivity of DNA sensor greatly. The difference of electron transfer resistance (ΔR_et) was linear with the logarithm of complementary oligonucleotides sequence concentrations in the range of 2.0×10^?12 to 9.0×10^?8 M, and the detection limit was 6.7×10^?13 M. In addition, the DNA sensor showed a fairly good reproducibility and stability during repeated regeneration and hybridization cycles.     

Hydrogen Bonding or Stacking Interactions in Differentiating Duplex Stability in Oligonucleotides Containing Synthetic Nucleoside Probes for Alkylated DNA

Oligonucleotides that hybridize to modified DNA are useful chemical tools to probe the noncovalent interactions that stabilize DNA duplexes. In an effort to better understand the interactions that influence the specificity of hybridization probes for O⁶‐alkylguanine lesions, we examined a series of synthetic nucleoside analogues (BIM, Benzi, and Peri) with respect to their ability to stabilize duplex DNA comprised of native or damaged DNA oligonucleotides. The base‐modified nucleoside analogues contained systematically varied hydrogen‐bonding and π‐stacking properties. The nucleoside probes were incorporated into DNA and paired opposite canonical bases (A, T, C, or G), O⁶‐methylguanine (O⁶‐MeG), O⁶‐benzylguanine (O⁶‐BnG), or a stable abasic site analogue (tetrahydrofuran, THF). On the basis of the free energy of duplex formation, the highest degree of stabilization was observed when Peri was paired opposite O⁶‐MeG. The thermodynamic data suggest that the smaller probes stabilize DNA duplexes more through hydrogen bonding, whereas the larger probes, with a greater capacity to π stack, contribute to duplex stabilization more on the basis of base stacking. These results demonstrate that increased helix stability could be achieved when BIM, Benzi, or Peri were paired opposite damage‐containing DNA rather than unmodified DNA (that is, O⁶‐MeG rather than G). This knowledge is expected to be useful in the design and development of nucleoside analogues for uses in DNA‐based technologies.     

Gold nanoparticle aggregation-based highly sensitive DNA detection using atomic force microscopy

The potential ability of atomic force microscopy (AFM) as a quantitative bioanalysis tool is demonstrated by using gold nanoparticles as a size enhancer in a DNA hybridization reaction. Two sets of probe DNA were functionalized on gold nanoparticles and sandwich hybridization occurred between two probe DNAs and target DNA, resulting in aggregation of the nanoparticles. At high concentrations of target DNA in the range from 100 nM to 10 μM, the aggregation of gold nanoparticles was determined by monitoring the color change with UV-vis spectroscopy. The absorption spectra broadened after the exposure of DNA–gold nanoparticles to target DNA and a new absorption band at wavelengths >600 nm was observed. However, no differences were observed in the absorption spectra of the gold nanoparticles at low concentrations of target DNA (10 pM to 10 nM) due to insufficient aggregation. AFM was used as a biosensing tool over this range of target DNA concentrations in order to monitor the aggregation of gold nanoparticles and to quantify the concentration of target DNA. Based on the AFM images, we successfully evaluated particle number and size at low concentrations of target DNA. The calibration curve obtained when mean particle aggregate diameter was plotted against concentration of target DNA showed good linearity over the range 10 pM to 10 nM, the working range for quantitative target DNA analysis. This AFM-based DNA detection technique was three orders of magnitude more sensitive than a DNA detection method based on UV-vis spectroscopy.     

亚甲基蓝与鲱鱼精DNA相互作用的光谱法研究

以吖啶橙(AO)作为光谱探针, 采用UV和荧光光谱等方法研究了亚甲基蓝(MB)与鲱鱼精DNA的作用机制. 确定了在低浓度MB时, MB与DNA以嵌插方式作用; 而在高浓度MB时, MB与DNA之间为混合作用方式. 结合比n(MB)∶n(DNA)＝10∶1, 结合常数 ＝2.46×10⁵ L•mol^－1, MB-DNA复合物的表观摩尔吸光系数ε＝5.70×10⁶ L•mol^－1•cm^－1. 同时研究了酸度和温度等对MB与DNA相互作用的影响, 热力学研究推导了MB结合DNA为焓驱动反应.     

Potentiometric DNA Sensor Based on Electropolymerized Phenothiazines for Protein Detection

Novel method of potentiometric detection of DNA‐protein interactions has been proposed. For this purpose, polymeric phenothiazine dyes, methylene blue (MB) and methylene green (MG), were electrochemically deposited onto the glassy carbon electrode and covered with double stranded DNA (dsDNA) as a target for antibodies (DNA‐sensor) or DNA aptamer specific to human α‐thrombin (aptasensor). The biosensors were consecutively incubated at pH 7.5 and 3.0 and the difference in potentials, ΔE, was used as a measure of protein concentration. The potentiometric DNA‐sensors were tested in standard serum of autoimmune disease patients (systemic lupus erythemathosus (SLE) and autoimmune thyroidites). It was shown, that the ΔE value of DNA‐sensor depends on the dilution of serum in the range from 1 : 1 to 1 : 100. Nonthermostated serum exhibited bell‐shape dependence of ΔE on serum dilution due to interfering effect of serine proteins at maximum dilution between 1 : 20 and 1 : 50. For SLE serum thermostated at 56 °C the ΔE linearly decreased as a function of serum dilution and reached saturation at dilution 1 : 20. Similarly the changes in the potential of aptasensor allowed us to determine the α‐thrombin in the range from 1 nM to 1 μM. The Faradic impedance spectra measured at presence of redox probe [Fe(CN)₆]^4?/3? revealed changes in the resistance and capacitance attributed to the shielding effect of anti‐DNA antibodies and an increase in the electron transfer. The developed potentiometric biosensors can be used for preliminary diagnostics of autoimmune diseases and thrombin detection with sensitivity comparable to traditional methods. The developed assay is, however simpler and cheaper in comparison with commonly used methods.     

Determination of DNA Hypermethylation Using Anti‐cancer Drug‐Temozolomide

An electrochemical drug‐DNA biosensor was developed for the detection of interaction between the anti‐cancer drug, Temozolomide (TMZ), and DNA sequences by using Differential Pulse Voltammetry at the graphite electrode surfaces. TMZ is a pro‐drug and an alkylating agent that crosses the blood‐brain barrier, so it is mainly used for brain cancers treatment. In this study, we aim to develop a‐proof‐of‐concept study to investigate the effect of TMZ on formerly methylated DNA sequences since TMZ shows its anti‐cancer activity by methylating the DNA. Interaction between TMZ and DNA causes localized distortion of DNA away from an idealized B‐form, resulting in a wider major groove and greater steric accessibility of functional groups in the base of the groove. According to the results, TMZ behaves as a ‘hybridization indicator’ because of its different electrochemical behavior to different strands of DNA. After interaction with TMZ, hybrid (double stranded DNA‐dsDNA) signals decreased dramatically whereas probe (single stranded DNA‐ssDNA) and control signals remain almost unchanged. The signal differences enabled us to distinguish ssDNA and dsDNA without using a label or tag. It is the first study to demonstrate the interaction between the TMZ and dsDNA created from probe and target. We use specific oligonucleotides sequences instead of using long dsDNA sequences.