Convective heat transfer in a parallel plate channel with porous lining

The paper proposes a theoretical model for the study of flow and heat transfer in a parallel plate channel, one of whose walls is lined with non-erodible porous material, both the walls being kept at constant temperatures. The analysis uses Brinkman model in the porous medium and employs the velocity and temperature slips at the interface (the so called nominal surface). The influence of the thickness as well as the permeability of the porous medium on the flow field and Nusselt numbers at the walls is investigated.

---

Konvektive Wärmeübertragung in einem Parallelplattenkanal mit porösem Überzug

Zusammenfassung Die vorliegende Arbeit befaßt sich mit dem Vorschlag eines theoretischen Modells, um die Wärmeübertragung in einem Parallelplattenkanal mit unauswaschbarem porösem Überzug zu studieren. Die Strömung innerhalb des porösen Überzugs ist mit Hilfe der Brinkmannschen Gleichung analysiert. An der Grenze (der sogenannten Nominalfläche) zwischen dem Überzug und der freien Strömung sind die Geschwindigkeitsgleitung und die Temperaturgleitung benutzt. Die Beeinflussung des Geschwindigkeitsfelds und die Nusseltschen Zahlen an den Wänden in Abhängigkeit von der Dicke und der Durchlässigkeit des porösen Überzugs ist untersucht.

---

Nomenclature u streamwise velocity in Zone 1 (Fig. 1) - û streamwise velocity in Zone 2 (Fig. 1) - p pressure - coefficient of viscosity of the fluid - k absolute permeability of the material used for lining - density of the fluid - R Reynolds number - the average velocity in Zone 1 (Fig. 1) - T temperature in Zone 1 (Fig. 1) - T temperature in Zone 2 (Fig. 1) - K thermal conductivity in Zones 1 and 2 (Fig. 1) - M ₁ non-dimensional mass flow rate in Zone 1 (Fig. 1) - M ₂ non-dimensional mass flow rate in Zone 2 (Fig. 1) - (Nu)_U Nusselt number at the upper plate (Fig. 1) - (Nu) _L Nusselt number at the lower plate (Fig. 1) - _E experimental value of the temperature in the channel (with porous lining) at a specified point - _E/* experimental value of the temperature in the channel (without porous lining) at a specified point     

Numerical investigation of heat transfer and fluid flow characteristics inside a wavy channel

The periodically fully developed laminar heat transfer and fluid flow characteristics inside a two-dimensional wavy channel in a compact heat exchanger have been numerically investigated. Calculations were performed for Prandtl number 0.7, and Reynolds number ranging from 100 to 1,100 on non-orthogonal non-staggered grid systems, based on SIMPLER algorithm in the curvilinear body-fitted coordinates. Effects of wavy heights, lengths, wavy pitches and channel widths on fluid flow and heat transfer were studied. The results show that overall Nusselt numbers and friction factors increase with the increase of Reynolds numbers. According to the local Nusselt number distribution along channel wall, the heat transfer may be greatly enhanced due to the wavy characteristics. In the geometries parameters considered, friction factors and overall Nusselt number always increase with the increase of wavy heights or channel widths, and with the decrease of wavy lengths or wavy pitches. Especially the overall Nusselt number significantly increase with the increase of wavy heights or channel widths, where the flow may become into transition regime with a penalty of strongly increasing in pressure drop. An erratum to this article can be found at     

Conjugate heat transfer in square enclosures

Building elements represented by square vertical enclosures encircled with finite walls or with centered solid body, could maintain the equivalent fluid volumes through the volume ratio scale. Present work aims to investigate the fluid flow and heat transfer in these two building elements. Complete two-dimensional numerical simulation of the conjugate heat conduction and natural convection occurring in both enclosures is carried out. An analytical expression for the minimum size of the inserted body at which the body begins to suppress the natural convection flow is proposed and validated by the numerical results. The fluid flow and heat transfer characteristics are analyzed through the streamlines, heatlines, and total heat transfer rates across both enclosures. Results reveal that heat transfer rates across both enclosures are complex functions of the volume ratio scale, Rayleigh number, and the relative thermal conductivity.     

Friction and forced convective heat transfer in a sintered porous channel with obstacle blocks

This work experimentally studies the flow characteristics and forced convective heat transfer in a sintered porous channel that filled with sintered copper beads of three average diameters ( 0.830, and 1.163 mm). The pressure drop and the local temperature measurements can be applied to figure out the distributions of the friction coefficient and the heat transfer coefficient. Three sintered porous channels differ in the arrangement of obstacle blocks. Model A has no obstacle. Models B and C have five obstacle blocks facing down and up, respectively, in a sintered porous channel. The range of experimental parameters, porosity, heat flux, and effect of forced convection are 0.370 ≤ ɛ ≤ 0.385, q=0.228, 0.872, 1.862 W/cm², and 200 ≤ Re _d ≤ 800. The permeability and inertia coefficient of each of the three sintered porous channels are analyzed. The results for Model A agree with those obtained by previous investigations in C _f distribution. The heat transfer of Model C exceeds that of Model A by approximately 20%. Finally, a series of empirical correlation equations were obtained for practical applications and engineering problems.     

Analysis of fluid flow and heat transfer in a channel with intermittent heated porous blocks

A numerical study of forced convection enhancement in a channel intermittently heated is presented in this work. The use of porous blocks mounted on the heated parts of the channel to improve thermal performance is investigated. In order to account for the inertia, drag and boundary effects, the Brinkman-Forchheimer-extended Darcy model is adopted for the flow inside the porous regions. The effects of several parameters such as Darcy number, the block dimensions, the number of blocks and the thermal conductivity ratio are documented. The results show that the blocks may alter substantially the flow pattern depending on the permeability of the porous medium, and may improve the heat transfer and reduce the wall temperature under certain circumstances. Received on 9 June 1997     

Conjugate heat transfer simulation of a rectangular natural circulation loop

In this article, conjugate heat transfer characteristics of a single-phase rectangular natural circulation loop were investigated numerically. Effects of the wall thermal conductivity and the wall thickness on the heat transfer behavior in a circulation loop with fixed geometrical configuration were investigated in detail. The presence of axial conduction through thick and highly conductive loop wall tends to strengthen markedly the buoyancy-induced circulating flow in the loop at lower Ra*.     

Conjugate model for heat and mass transfer of porous wall in the high temperature gas flow

Heat and mass transfer of a porous permeable wall in a high temperature gas dynamical flow is considered. Numerical simulation is conducted on the ground of the conjugate mathematical model which includes filtration and heat transfer equations in a porous body and boundary layer equations on its surface. Such an approach enables one to take into account complex interaction between heat and mass transfer in the gasdynamical flow and in the structure subjected to this flow. The main attention is given to the impact of the intraporous heat transfer intensity on the transpiration cooling efficiency. The project supported by the National Natural Science Foundation of China (19889209) and Russian Foundation for Basic Research (97-02-16943)     

Conjugate heat transfer within a concentric annulus filled with micropolar fluid

This paper investigates numerically the conjugate heat transfer in an annulus between two concentric cylinders. The annulus contains micropolar fluid and is heated isothermally from its inner wall. The effect of Rayleigh number, thickness of inner wall, inner wall-fluid thermal conductivity ratio, and material parameters of micropolar fluid on heat transfer rate within the annulus has been investigated. The study has shown that for low Rayleigh number regimes and for thermal conductivity of the inner wall greater than that of the fluid, the increase of inner wall thickness increases the heat transfer rate through the annulus and vice versa. While for convection dominating regimes Ra ≥ 10⁴ the increase of inner wall thickness decreases the heat transfer rate. Moreover, the study has shown that for fixed geometrical and flow parameters the heat transfer decreases in case of micropolar fluids in comparison with that of Newtonian fluids.     

Transient forced convection heat transfer in a channel

A numerical analysis is made of incompressible transient turbulent flow heat transfer between two parallel plates when there is a step jump in space along the channel in wall heat flux or wall temperature. The variation of the fluid velocity and effective diffusivity over the channel cross section are accounted for. The fluid is assumed to have a fully-developed turbulent velocity profile throughout the length of the channel. The thermal responses of the system are obtained by solving energy equation for air by a digital computer. The results are presented in graphical forms. The stability of the finite difference solution is studied and condition for the stability of the difference solution is derived. A method is given to obtain velocity distributions from the distribution of turbulent eddy diffusivity of momentum. Variations of Nusselt numbers are obtained as a function of time and space. Steady-state values are also given and compared with the published results.     

A numerical study of heat transfer of a porous block with the random porosity model in a channel flow

 In this paper, heat transfer of a hot plate with a porous block in a channel flow is numerically investigated. A porous block is simulated as a fin type heat sink. The random/artificial porosity models are used to generate the distribution of porosity. In fact, the distribution of porosity in porous medium is irregular, thus the random porosity model is more realistic than the constant or variable porosity model to describe the phenomena happening in porous medium. Therefore, the distribution of porosity of porous block obeys the random porosity model, and the factors of mean porosity and standard deviation are taken into consideration. The variations of the porosity and the velocity in porous block are no longer smooth. For obtaining more heat transfer rate, the artificial porosity model is proposed. The heat transfer rates of the several cases derived by the artificial porosity model are better than those of the random porosity model. The thermal performance of porous block is larger than that of solid block as the mean porosity is larger than 0.5. Received on 5 March 2001 / Published online: 29 November 2001     

Conjugate heat transfer in enclosures with openings for ventilation

Conjugate heat transfer by natural convection and conduction in enclosures with openings has been studied by a numerical method. The enclosure contained a chimney consisting of a vertical solid wall, which was insulated on one side and a constant heat flux applied on the other. Vertical boundaries with openings were isothermal and horizontal boundaries adiabatic. These problems are encountered in heat transfer in buildings and heat management in electronic equipment. Two dimensional equations of conservation of mass, momentum and energy, with the Boussinesq approximation are solved using the Simpler method. Various geometrical parameters were: aspect ratio, A from 0.5 to 2.0, openings' heights, h ₁ and h ₂ from 0.10 to 0.30, orifice height, h ₃ from 0.05 to 0.15, insulation thickness, w ₁ from 0 to 0.10, wall thickness, w ₂ from 0.05 to 0.15 and chimney width, w ₃ from 0.05 to 0.15. Rayleigh number, Ra was varied from 10 ⁸ to 10 ¹² and the conductivity ratio, k _r was from 1 to 40. The results are reduced in terms of the normalized Nusselt number, Nu and volume flow rate, V? as a function of Ra number, and other non dimensional geometrical parameters. The isotherms and streamlines are produced for various Ra numbers and geometrical conditions. It is found that Nu and V? are both an increasing function of Ra, h ₁ at high Ra numbers, h ₃, and k _r. They are a decreasing function of h ₁ at low Ra numbers, h ₂, and w ₂. Nu and V? have optima with respect to w ₁, w ₃ and A.     

Two fluid flow and heat transfer in an inclined channel containing porous and fluid layer

Convective flow and heat transfer in an inclined channel bounded by two rigid plates held at constant different temperatures with one region filled with porous matrix saturated with a viscous fluid and another region with a clear viscous fluid different from the fluid in first region is studied analytically. The coupled nonlinear governing equations are solved using regular perturbation method. It is found that the presence of porous matrix in one of the region reduces the velocity and temperature. Results have been presented for a wide range of governing parameters such as Grashof number, porous parameter, angle of inclination, ratio of heights of the two layers and also the ratio of viscosities.     

Mixed convection heat transfer from a horizontal channel with protruding heat sources

A numerical investigation is carried out to study fluid flow and heat transfer characteristics of conjugate mixed convection from a two dimensional horizontal channel with four protruding heat sources mounted on one of the finite thick channel walls. The flow is assumed as laminar, hydrodynamically and thermally developing. Water and FC70 are the fluids under consideration. The geometric parameters such as spacing between the channel walls (S), size of protruding heat sources (L_h×t_h), thickness of substrate (t) and spacing between heat sources (b) are fixed. Results are presented to show the effect of parameters such as Re_S, Gr_S^*, Pr, k_p/k_f and k_s/k_f on fluid flow and heat transfer characteristics. Using the method of asymptotic expansions, correlations are also presented for the maximum temperature of heat source.     

Numerical simulation of three-dimensional natural convection inside a heat generating anisotropic porous medium

Natural convection in anisotropic heat generating porous medium enclosed inside a rectangular cavity has been studied. A 3D finite volume based code is developed using the Darcy approximation and validated using experimental results of natural convection around an enclosed rod bundle. Subsequently, detailed simulation is carried out for a cavity, filled with orthotropic porous medium. The effects of heat generation, geometry and anisotropy are studied. Anisotropy is found to be of significant importance for both maximum value and distribution of temperature.     

Conjugate heat transfer in the unbounded flow of a viscoelastic fluid past a sphere

This work addresses the conjugate heat transfer of a simplified PTT fluid flowing past an unbounded sphere in the Stokes regime (Re = 0.01). The problem is numerically solved with the finite-volume method assuming axisymmetry, absence of natural convection and constant physical properties. The sphere generates heat at a constant and uniform rate, and the analysis is conducted for a range of Deborah (0 ≤ De ≤ 100), Prandtl (10⁰ ≤ Pr ≤ 10⁵) and Brinkman (0 ≤ Br ≤ 100) numbers, in the presence or absence of thermal contact resistance at the solid–fluid interface and for different conductivity ratios (0.1 ≤ κ ≤ 10). The drag coefficient shows a monotonic decrease with De, whereas the normalized stresses on the sphere surface and in the wake first increase and then decrease with De. A negative wake was observed for the two solvent viscosity ratios tested (β = 0.1 and 0.5), being more intense for the more elastic fluid. In the absence of viscous dissipation, the average Nusselt number starts to decrease with De after an initial increase. Heat transfer enhancement relative to an equivalent Newtonian fluid was observed for the whole range of conditions tested. The dimensionless temperature of the sphere decreases and becomes more homogeneous when its thermal conductivity increases in relation to the conductivity of the fluid, although small changes are observed in the Nusselt number. The thermal contact resistance at the interface increases the average temperature of the sphere, without affecting significantly the shape of the temperature profiles inside the sphere. When viscous dissipation is considered, significant changes are observed in the heat transfer process as Br increases. Overall, a simplified PTT fluid can moderately enhance heat transfer compared to a Newtonian fluid, but increasing De does not necessarily improve heat exchange.     

Conjugate heat transfer study of incompressible turbulent offset jet flows

In the present case, the conjugate heat transfer involving a turbulent plane offset jet is considered. The bottom wall of the solid block is maintained at an isothermal temperature higher than the jet inlet temperature. The parameters considered are the offset ratio (OR), the conductivity ratio (K), the solid slab thickness (S) and the Prandtl number (Pr). The Reynolds number considered is 15,000 because the flow becomes fully turbulent and then it becomes independent of the Reynolds number. The ranges of parameters considered are: OR = 3, 7 and 11, K = 1–1,000, S = 1–10 and Pr = 0.01–100. High Reynolds number two-equation model (k–ε) has been used for turbulence modeling. Results for the solid–fluid interface temperature, local Nusselt number, local heat flux, average Nusselt number and average heat transfer have been presented and discussed.