Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

Direct Electrochemistry of Myoglobin on a Room Temperature Ionic Liquid Modified Electrode and Its Application to Nitric Oxide Biosensing

Myoglobin (Myb) was successfully immobilized on a room temperature ionic liquid (RTIL), 1‐ethyl‐3‐methyl imidazolium tetrafluoroborate ([EMIM][BF₄]) modified basal plane graphite (BPG) electrode. The electrochemical behavior of Myb on RTIL modified BPG electrode was explored and the results from cyclic voltammetry (CV) showed a well‐defined and quasi‐reversible CV peaks with a formal potential of ?0.379 V (versus Ag/AgCl) in a phosphate buffer solution (pH 7.0). RTIL shows an obvious promotion for the direct electron‐transfer between Myb and BPG electrode. Myb adsorbed on electrode surface exhibits an obvious electrocatalytic activity for the reduction of nitric oxide (NO). The catalytic current is corresponding linearly to the NO concentration in the range of 7.0×10^?7 to 7.0×10^?6 M with a limit of detection of 2.0×10^?7 M (three times the ratio of signal to noise, S/N=3).     

Electrocatalysis Oxidation of GMP Based on Layered Double Hydroxide Functionalized with Anionic Surfactant and Room Temperature Ionic Liquid Modified Glassy Carbon Electrode

The electrocatalysis oxidation of guanosine‐5′‐monophosphate (GMP) was investigated on Mg‐Al layered double hydroxide (LDH) functionalized with sodium dodecyl sulfate (SDS) and room temperature ionic liquid (RTIL) modified glass carbon electrode (GCE). The cyclic voltammogram of GMP on the modified electrode (RTIL/ LDH‐SDS/GCE) exhibited a well defined anodic peak at 1.091 V in 0.2 mol·L^?1 pH 4.4 acetate buffer solution. The GMP oxidation was enhanced in the presence of anionic surfactant in the ?lms. The results suggest that the surfactant molecules intercalate the LDH layers to preconcentrate GMP molecules and the RTIL showed good ionic conductivity. The experimental parameters were optimized, the kinetic parameters were investigated and the probable oxidation mechanism was proposed. Under the optimized conditions, the oxidation peak current was proportional to GMP concentration in the range from 5.0×10^?7 to 1.0×10^?4 mol·L^?1 with the correlation coefficient of 0.9987 and the detection limit was 1.0×10^?7 mol·L^?1. The RTIL/LDH‐SDS/GCE showed a good electrochemical response to the oxidation of GMP and would be developed into a new biosensor.     

The NADH Electrochemical Detection Performed at Carbon Nanofibers Modified Glassy Carbon Electrode

In this work, the capability of carbon nanofibers to be used for the design of catalytic electrochemical biosensors is demonstrated. The direct electrochemistry of NADH was studied at a glassy carbon electrode modified using carbon nanofibers. A decrease of the oxidation potential of NADH by more than 300 mV is observed in the case of the assembled carbon nanofiber‐glassy carbon electrode comparing with a bare glassy carbon electrode. The carbon nanofiber‐modified electrode exhibited a wide linear response range of 3×10^?5 to 2.1×10^?3 mol L^?1 with a correlation coefficient of 0.997 for the detection of NADH, a high specific sensitivity of 3637.65 (μA/M cm²), a low detection of limit (LOD=3σ) of 11 μM, and a fast response time (3 s). These results have confirmed the fact that the carbon nanofibers represent a promising material to assemble electrochemical sensors and biosensors.     

Electrocatalysis and Voltammetric Determination of Dopamine at a Calix[4]arene Crown‐4 Ether Modified Glassy Carbon Electrode

A sensitive and selective electrochemical method for the determination of dopamine (DA) was developed using a calix[4]arene crown‐4 ether (CACE) film modified glassy carbon electrode (GCE).The modified electrode exhibited good electrocatalytic activity for electrochemical oxidation of DA in the pH 6.00 Britton–Robinson buffer solution, and ascorbic acid (AA) did not interfere with it. The diffusion coefficient (D=2.7×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient (α=0.54) of DA at the surface of CACE were determined using electrochemical approaches. The catalytic oxidation peak currents showed a linear dependence on the DA concentration and a linear analytical curve was obtained in the range of 2.0×10^?5–1.0×10^?3 M of DA with a correlation coefficient of 0.9990. The detection limit (S/N=3) was estimated to be 3.4×10^?6 M. This method was also examined for the determination of DA in an injection sample. In addition, effects of possible interferences were investigated. The present work shows the potential of the proposed method for the fabrication of a modified electrode, as it can be effectively used for voltammetric detection of DA.     

Electrochemical Behavior of Chloranil Chemically Modified Carbon Paste Electrode. Application to the Electrocatalytic Determination of Ascorbic Acid

A p‐chloranil modified carbon paste electrode was constructed and the electrochemical behavior of this electrode was studied in the aqueous solution with different pH. From the E_1/2–pH diagram for this compound the values of formal potential E^0' and pK_a of some different redox and acid‐base couples depending on the solution pH were estimated. The diffusion coefficient, D, value for p‐chloranil was estimated 1.5×10^?7 cm² s^?1. It has been shown by direct current cyclic voltammetry and double potential step chronoamperometry, that this p‐chloranil incorporated carbon paste electrode, can catalyze the oxidation of ascorbic acid in the aqueous buffered solution. Under the optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 325 mV less positive than that at an unmodified carbon past electrode. The catalytic oxidation peak currents was linearly dependent on the ascorbic acid concentration and a linear calibration curve was obtained in the range of 7×10^?5 M–4×10^?3 M of ascorbic acid with a correlation coefficient of 0.9998. The limit of detection (3σ) was determined as 3.5×10 ^?5 M. This method was used as simple, selective and precise voltammetric method for determination of ascorbic acid in pharmaceutical preparations.     

Voltammetric Ion‐Selective Nanocomposite Carbon Paste Electrode for Determination of Erbium at the Interface Between two Immiscible Electrolyte Solutions

In this study for the first time a novel erbium(III) voltammetric ion‐selective nanocomposite carbon‐paste electrode was introduced based on the concept of ion transfer at the interface between two immiscible electrolyte solutions. N′‐(2‐hydroxy‐1,2‐diphenylethylidene) benzohydrazide (HDB) was used as a selective ionophore in the composition of the carbon paste. The ionophore facilitates transfer of Er(III) from the aqueous solution to the room temperature ionic liquid (RTIL) phase after reduction of the redox probe to maintain charge neutrality. The plot of the peak potential versus the logarithm of the concentration exhibits a Nernstian response (19.9±0.2 mV decade^?1) toward Er(III) in the range of 7.5×10^?7–1.0×10^?1 mol L^?1 with detection limit of 5.0×10^?7 mol L^?1. The proposed sensor shows a fast response time of about 5 s.     

Nanostructured Base Electrochemical Sensor for Simultaneous Quantification and Voltammetric Studies of Levodopa and Carbidopa in Pharmaceutical Products and Biological Samples

A novel carbon paste electrode modified with carbon nanotubes and 5‐amino‐2′‐ethyl‐biphenyl‐2‐ol (5AEB) was fabricated. The electrochemical study of the modified electrode, as well as its efficiency for electrocatalytic oxidation of levodopa (LD) and carbidopa (CD), is described. Cyclic voltammetry (CV) was used to investigate the redox properties of this modified electrode at various scan rates. The apparent charge transfer rate constant, k_s, and transfer coefficient, a, for electron transfer between 5AEB and CPE were calculated as 17.3 s^?1 and 0.5, respectively. Square wave voltammetry (SWV) exhibits a linear dynamic range from 2.5×10^?7 to 2.0×10^?4 M and a detection limit of 9.0×10^?8 M for LD.     

Electrochemical Behaviors of Adenosine‐5′‐triphosphate on Molecular Wire Modified Carbon Paste Electrode and Its Sensitive Detection

A new electrochemical method was proposed for the determination of adenosine‐5′‐triphosphate (ATP) based on the electrooxidation at a molecular wire (MW) modified carbon paste electrode (CPE), which was fabricated with diphenylacetylene (DPA) as the binder. A single well‐defined irreversible oxidation peak of ATP appeared on MW‐CPE with adsorption‐controlled process and enhanced electrochemical response in a pH 3.0 Britton‐Robinson buffer solution, which was due to the presence of high conductive DPA in the electrode. The electrochemical parameters of ATP were calculated with the electron transfer coefficient (α) as 0.54, the electron transfer number (n) as 1.9, the apparent heterogeneous electron transfer rate constant (k_s) as 2.67 × 10^?5 s^?1 and the surface coverage (Γ_T) as 4.15 × 10^?10 mol cm^?2. Under the selected conditions the oxidation peak current was proportional to ATP concentration in the range from 1.0 × 10^?7 mol L^?1 to 2.0 × 10^?3 mol L^?1 with the detection limit as 1.28 × 10^?8 mol L^?1 (3σ) by sensitive differential pulse voltammetry. The proposed method showed good selectivity without the interferences of coexisting substances and was successful applied to the ATP injection samples detection.     

Acetylferrocene Modified Carbon Paste Electrode; A Sensor for Electrocatalytic Determination of Hydrazine

The electrocatalytic oxidation of hydrazine at a carbon paste electrode spiked with acetylferrocene as a mediator was studied by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. In contrast to other ferrocenic compounds, acetylferrocene exhibits a chemical irreversible behavior, but it can act as an effective mediator for electrocatalytic oxidation of hydrazine, too. The heterogeneous electron transfer rate constant between acetylferrocene and the electrode substrate (carbon paste) and the diffusion coefficient of spiked acetylferrocene in silicon oil were estimated to be about 3.45×10^?4 cm s^?1 and 4.45×10^?9 cm² s^?1, respectively. It has been found that under the optimum conditions (pH 7.5) the oxidation of hydrazine occurs at a potential of about 228 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak current of hydrazine was linearly dependent on its concentration and the obtained linear range was 3.09×10^?5 M–1.03×10^?3 M. The detection limit (2σ) has been determined as 2.7×10^?5 M by cyclic voltammetry. Also, the peak current was increased linearly with the concentration of hydrazine in the range of 1×10^?5 M–1×10^?3 M by differential pulse voltammetry with a detection limit of 1×10^?5 M. This catalytic oxidation of hydrazine has been applied as a selective, simple, and precise new method for the determination of hydrazine in water samples.     

Electrocatalytic Oxidation and Voltammetric Determination of L‐Cysteic Acid at the Surface of p‐Bromanil Modified Carbon Paste Electrode

The electrochemical properties of L ‐cysteic acid studied at the surface of p‐bromanil (tetrabromo‐p‐benzoquinone) modified carbon paste electrode (BMCPE) in aqueous media by cyclic voltammetry (CV) and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00) in cyclic voltammetry, the oxidation of L ‐cysteic acid at the surface of BMCPE occurs at a half‐wave potential of p‐bromanil redox system (e.g., 100 mV vs. Ag|AgCl|KCl_sat), whereas, L ‐cysteic acid was electroinactive in the testing potential ranges at the surface of bare carbon paste electrode. The apparent diffusion coefficient of spiked p‐bromanil in paraffin oil was also determined by using the Cottrell equation. The electrocatalytic oxidation peak current of L ‐cysteic acid exhibits a linear dependency to its concentration in the ranges of 8.00×10^?6 M–6.00×10^?3 M and 5.2×10^?7 M–1.0×10^?5 M using CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (2σ) were determined as 5.00×10^?6 M and 4.00×10^?7 M by CV and DPV methods. This method was used as a new, selective, rapid, simple, precise and suitable voltammetric method for determination of L ‐cysteic acid in serum of patient's blood with migraine disease.     

Direct Voltammetry of Copper,Zinc‐Superoxide Dismutase Immobilized onto Electrodeposited Nickel Oxide Nanoparticles: Fabrication of Amperometric Superoxide Biosensor

Direct electron transfer of immobilized copper, zinc‐superoxide dismutase (SOD) onto electrodeposited nickel‐oxide (NiOx) nanoparticle modified glassy carbon (GC) electrode displays a well defined redox process with formal potential of ?0.03 V in pH 7.4. Cyclic voltammetry was used for deposition of (NiOx) nanoparticles and immobilization of SOD onto GC electrode. The surface coverage (Γ) and heterogeneous electron transfer rate constant (k_s) of immobilized SOD are 1.75×10^?11 mol cm^?2 and 7.5±0.5 s^?1, respectively. The biosensor shows a fast amperometric response (3 s) toward superoxide at a wide concentration range from 10 µM to 0.25 mM with sensitivity of 13.40 nA µM^?1 cm^?2 and 12.40 nA µM^?1 cm^?2, detection limit of 2.66 and 3.1 µM based on anodically and cathodically detection. This biosensor exhibits excellent stability, reproducibility and long life time.     

Electrochemical Behavior and Determination of L‐Tyrosine at Single‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

Based on single‐walled carbon nanotubes (SWCNTs) modified glassy carbon electrode (GCE/SWCNTs), a novel method was presented for the determination of L ‐tyrosine. The GCE/SWCNTs exhibited remarkable catalytic and enhanced effects on the oxidation of L ‐tyrosine. In 0.10 mol/L citric acid‐sodium citrate buffer solution, the oxidation potential of L ‐tyrosine shifted negatively from +1.23 V at bare GCE to +0.76 V at GCE/SWCNTs. Under the optimized experimental conditions, the linear range of the modified electrode to the concentration of L ‐tyrosine was 5.0×10^?6–2.0×10^?5 mol/L (R₁=0.9952) and 2.7×10^?5–2.6×10^?4 mol/L (R₂=0.9998) with a detection limit of 9.3×10^?8 mol/L. The kinetic parameters such as α (charge transfer coefficient) and D (diffusion coefficient) were evaluated to be 0.66, 9.82×10^?5 cm² s^?1, respectively. And the electrochemical mechanism of L ‐tyrosine was also discussed.     

Electrocatalysis of Chemical Warfare Agent Sulfur Mustard in Room Temperature Ionic Liquid

Room temperature ionic liquids (RTILs) have the potential for being ideal alternatives for organic solvents in chemical warfare agent (CWA) electrochemical reactions. In this paper, electrocatalysis of CWA sulfur mustard (SM) was achieved by exploring the potential advantage of RTIL methyltrioctylammonium bis (trifluoromethylsulfonyl) imide and further this methodology was used for the detection of CWA. The hydrophobicity of this RTIL offers the opportunity to use this methodology in field condition without environmental humidity effect. The diffusion coefficient calculated for SM in RTIL was 0.196×10⁻⁹ cm²/s. The electrochemical parameters deduced from cyclic voltammetry such as electron transfer coefficient (α), electron transfer number (n) and heterogenous rate constant were estimated 0.11, 2 and 4.41 s⁻¹, respectively. The electrocatalytic activity of the RTIL toward the electrochemical reduction and oxidation of CWA is evidenced, showing the potential of this novel approach for the oxidation of other toxic CWAs. The new RTIL based strategy provides an opportunity to develop field deployable detection of CWA and could provide a new paradigm shift in CWA detection approach, addressing the escalating threat of CWA.     

Sensitive amperometric pyridoxine sensor based on self‐assembled Prussian blue nanoparticle‐modified poly(o‐phenylenediamine)/glassy carbon electrode

Prussian blue nanoparticles (PBNPs) were prepared by a self‐assembly process on a glassy carbon electrode (GCE) modified with poly(o‐phenylenediamine) (PoPD) film. The stepwise fabrication process of PBNP‐modified PoPD/GCE was characterized using scanning electron microscopy and electrochemical impedance spectroscopy. The prepared PBNPs showed an average size of 70 nm and a homogeneous distribution on the surface of the modified electrode. The PBNPs/PoPD/GCE showed electrocatalytic activity towards the oxidation of pyridoxine (PN) and was used as an amperometric sensor. The modified electrode exhibited a linear response for PN oxidation over the concentration range 3–38.5 μM with a detection limit of ca 6.10 × 10^?7 M (S/N = 3) and sensitivity of 2.79936 × 10³ mA M^?1 cm^?2 using an amperometric method. The mechanism and kinetics of the catalytic oxidation reaction of PN were investigated using cyclic voltammetry and chronoamperometry. The values of α, k_cat and D were estimated as 0.36, 1.089 × 10² M^?1 s^?1 and 8.9 × 10^?5 cm² s^?1, respectively. This sensor also exhibited good anti‐interference and selectivity. Copyright © 2016 John Wiley & Sons, Ltd.     

Direct Electrochemistry of Glucose Oxidase Immobilized on Titanium Carbide‐Au Nanoparticles‐Fullerene C60 Composite Film and Its Biosensing for Glucose

The direct electrochemistry of glucose oxidase (GOD) immobilized on the designed titanium carbide‐Au nanoparticles‐fullerene C₆₀ composite film modified glassy carbon electrode (TiC‐AuNPs‐C₆₀/GCE) and its biosensing for glucose were investigated. UV‐visible and Fourier‐transform infrared spectra of the resulting GOD/TiC‐AuNPs‐C₆₀ composite film suggested that the immobilized GOD retained its original structure. The direct electron transfer behaviors of immobilized GOD at the GOD/TiC‐AuNPs‐C₆₀/GCE were investigated by cyclic voltammetry in which a pair of well‐defined, quasi‐reversible redox peaks with the formal potential (E^0′) of ‐0.484 V (vs. SCE) in phosphate buffer solution (0.05 M, pH 7.0) at the scan rate of 100 mV·s^?1 were obtained. The proposed GOD modified electrode exhibited an excellent electrocatalytic activity to the reduction of glucose, and the currents of glucose reduction peak were linearly related to glucose concentration in a wider linearity range from 5.0 × 10^?6 to 1.6 × 10^?4 M with a correlation coefficient of 0.9965 and a detection limit of 2.0 × 10^?6 M (S/N = 3). The sensitivity and the apparent Michaelis‐Menten constant (K_M^app) were determined to be 149.3 μA·mM^?1·cm^?2 and 6.2 × 10^?5 M, respectively. Thus, the protocol will have potential application in studying the electron transfer of enzyme and the design of novel electrochemical biosensors.     

Catalytic Adsorptive Stripping Chronopotentiometry of Co(II)‐DMG‐Bromate System at an In Situ Plated Lead Film Electrode

A novel catalytic adsorptive stripping chronopotentiometric (CC‐CAdSCP) procedure for the determination of Co(II) traces was developed using a lead film electrode (PbFE). The PbFE was generated in situ on a glassy carbon support from a 0.1 M ammonia buffer containing 1×10^?5 M Pb(II), 6.5×10^?5 M DMG and the target metals. An addition of 0.2 M NaBrO₃ to the solution yielded an 11‐fold catalytic enhancement of chronopotentiometric response of the Co(II)‐DMG complex. The CC‐CAdSCP curves were well‐developed, sharp and reproducible (RSD 5.0 % for 5×10^?9 M Co(II)). The limit of detection for Co(II) for 210 s of accumulation time was 4×10^?10 M (0.024 µg L^?1). In addition, the elaborated method allowed the simultaneous quantification of Co(II) and Ni(II) simultaneously.     

Effects of pH and Concentration on Cs Ions Sorption and Diffusion in Crushed Granite by Using Batch and Modified Capillary Method

A comprehensive evaluation of Cs ions sorption to and diffusion in crushed granite was conducted in this study. The sorption capacity of crushed granite suggested by the Langmuir model was 5.48 × 10^?6 mol‐Cs/g‐granite. The distribution coefficient (Kd) was around 7.5 mL/g and pH independent. By using an in‐diffusion method with a modified capillary column, some diffusion relevant parameters of Cs ions in crushed granite were derived. The apparent diffusion coefficient (Da) seemed unaffected by Cs concentration (1.15 × 10^?10 to 2.82 × 10^?10 m²/s, at 10^?7 and 10^?3 M, respectively). The determined effective diffusion coefficients (De) were located in the window from 8.59 × 10^?10 (10^?7 M) to 1.69 × 10^?9 (10^?3 M) m²/s. Under various pH environments, pH independent Da (9.0 × 10^?9 m²/s) and De (1.0 × 10^?9 m²/s) values were observed. Under current systems, consistently higher De than Da implied the diffusion of Cs ions was governed by surface diffusion phenomenon. Whereas the pH insensitive feature indicated the Cs sorption to crushed granite was mainly through ion‐exchange reaction. Moreover, further SEM/EDS mapping clearly showed the adsorbed Cs ions were highly concentrated on the fracture surface of biotite.     

Electrocatalytic Oxidation of Sulfite on a Cobalt Pentacyanonitrosylferrate Film Modified Glassy Carbon Electrode

The electrocatalytic oxidation of sulfite has been studied on the cobalt pentacyanonitrosylferrate modified glassy carbon electrode (CoPCNF). The CoPCNF films on the glassy carbon electrodes show an excellent electrocatalytic activity toward the oxidation of sulfite in 0.5 M KNO₃. The kinetics of the catalytic reaction was investigated by using cyclic voltammetry, rotating disk electrode (RDE) voltammetry and chronoamperometry. The average value of the rate constant, K, for the catalytic reaction and the diffusion coefficient, D, were evaluated by different approaches for sulfite and found to be 2.9×10² M^?1s^?1 and 4.6×10^?6 cm²s^?1, respectively. At a fixed potential under hydrodynamic conditions (stirred solutions), the oxidation current is proportional to the sulfite concentration and the calibration plot was linear over the concentration range 5×10^?6–1×10^?4 M. The detection limit of the method is 3×10^?6 M., low enough for the trace sulfite determination.     

Application of a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole/carbon nanotube modified glassy carbon electrode for voltammetric determination of hydrazine in water samples

The electrochemical behaviour of hydrazine at a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole‐triazole/carbon nanotube modified glassy carbon electrode has been studied. The modified electrode shows an excellent electrocatalytic activity for the oxidation of hydrazine and accelerates electron transfer rate. The electrocatalytic current increases linearly with hydrazine concentration in the range 0.5–700.0 μm and the detection limit for hydrazine was 33.0 ± 2.0 nm . The diffusion coefficient (D = 2.5 ± 0.1 × 10^?5 cm² s^?1) and kinetic parameters such as the electron transfer coefficient, (α = 0.52) and the heterogeneous rate constant (k′ = 5.5 ± 0.1 × 10^?3 cm s^?1) for hydrazine were determined using electrochemical approaches. Finally, the method was employed for the determination of hydrazine in water samples. Copyright © 2013 John Wiley & Sons, Ltd.