Fabrication of Fe(CN)63− Functionalized PDDA/CdTe Layer‐by‐layer Film with Good Electron Transfer Ability

(PDDA/CdTe)_n layer‐by‐layer (LBL) film immobilized with Fe(CN)₆^3? was fabricated on the gold electrode. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were used to investigate the electrochemical properties of this film. The peak current of the immobilized Fe(CN)₆^3? increased as the number of the bilayers increased and was proportional to the scan rate. Compared with pure (PDDA/CdTe)_n and (PDDA/PSS)_n LBL film, Fe(CN)₆^3? immobilized (PDDA/CdTe)_n LBL film had good electron transfer ability. The immobility of Fe(CN)₆^3? into the film was attributed to its interaction with Cd²⁺ on the surface of CdTe QDs. Fe(CN)₆^3? also can interact with other metal ions, which would make Fe(CN)₆^3? release from the film. The concentrations of metal ions will affect the CV response of Fe(CN)₆^3? immobilized LBL film. It has provided a novel prototype of device or sensor for quantitative detection of metal ions.     

Redox Properties of Ferricyanide Ion on Layer‐by‐Layer Thin Film‐Coated Gold Electrodes; Effects of Type of Polycationic Components in the Film

The surface of a gold (Au) electrode was coated with layer‐by‐layer (LbL) thin films composed of poly(vinyl sulfate) (PVS) and different type of poly(amine)s including poly(allylamine) (PAH), poly(ethyleneimine) (PEI) and poly(diallyldimethylammonium chloride) (PDDA) and redox properties of ferricyanide ion ([Fe(CN)₆]^3?) on the LbL film‐coated Au electrodes were studied. The LbL film‐coated electrodes exhibited redox response to [Fe(CN)₆]^3? ion when the outermost surface of the LbL film was covered with the cationic poly(amine)s while virtually no response was observed on the LbL film‐coated electrodes whose outermost surface was covered with PVS due to an electrostatic repulsion between [Fe(CN)₆]^3? ion and the negatively‐charged PVS layer. The redox properties of [Fe(CN)₆]^3? ion on the LbL film‐coated electrodes significantly depended on the type of polycationic materials in the LbL film. The LbL film‐coated electrodes which had been immersed in the [Fe(CN)₆]^3? solution for 15 min exhibited redox response even in a [Fe(CN)₆]^3? ion‐free buffer solution, suggesting that [Fe(CN)₆]^3? ion is confined in the films. In the buffer solution, redox peaks were observed between +0.1 and 0.4 V depending on the type of polycations in the film. Thus, [Fe(CN)₆]^3? ion can be confined in the film and the redox potential is polycation‐dependent.     

A study of ion exchange selectivity coefficient by cyclic voltammetric measurement

An equation to express ion exchange selectivity coefficient was derived and used for calculating that of PPY film with the results obtained by cyclic voltammetric measurement. PPY film was synthesized by electrochemical method in aqueous solution using K₄Fe(CN)₆ as supporting electrolyte, and the anions were doped into the film. Ion exchange behaviour of doped Fe (CN)₆^3-/4- in the PPY film with Cl^?, NO₃^? or F^? ions in solution has been studied, and the corresponding ion exchange selectivity coefficients were determined.     

Layer-by-layer thin film-coated electrodes for electrocatalytic determination of ascorbic acid

Multilayer thin films composed of poly(allylamine hydrochloride) (PAH) and carboxymethyl cellulose (CMC) have been prepared on the surface of a gold (Au) disk electrode by a layer-by-layer deposition of PAH and CMC and ferricyanide ions ([Fe(CN)₆]³⁻) were confined in the film. [Fe(CN)₆]³⁻ ions can be successfully confined in the films from weakly acidic or neutral [Fe(CN)₆]³⁻ solutions, while, in basic solution, [Fe(CN)₆]³⁻ ion was not confined. The [Fe(CN)₆]³⁻ ion-confined Au electrode showed clear redox peaks in the cyclic voltammogram around 0.35 V versus Ag/AgCl. The amounts of [Fe(CN)₆]³⁻ ions confined in the films depended on the thickness of the films or the number of layers in the LbL films. The [Fe(CN)₆]³⁻ ion-confined Au electrode was used for electrocatalytic determination of ascorbic acid in the concentration range of 1-50 mM.     

Preparation,Characterization, and Electrocatalytic Properties of Cobalt Oxide and Cobalt Hexacyanoferrate Hybrid Films

Polynuclear mixed‐valent films of cobalt oxide and cobalt hexacyanoferrate (CoOCoHCF) have been deposited on electrode surfaces from a solution of Co²⁺ and Fe(CN)₆^3? ions by repetitive potential cycling method. Simultaneous cyclic voltammetry and electrochemical quartz crystal microbalance measurements demonstrate the steady growth of modified film. The effect of type of monovalent cations as well as acidity of the supporting electrolyte on film growth and redox behavior of resulting film was investigated. In pure supporting electrolyte, electrochemical responses of modified electrode resemble with that of a surface immobilized redox couple. The hybrid film electrodes showed electrocatalytic activity toward oxidation of NADH, hydrazine and hydroxylamine. The feasibility of using our modified electrodes for analytical application was also explored.     

Improving the electrochemical performances of active carbon-based supercapacitors through the combination of introducing functional groups and using redox additive electrolyte

High-performance and low-cost electrochemical capacitors (ECs) are essential for large-scale applications in energy storage. In this work, the specific capacitance of active carbon (AC) electrode was significantly improved through the combination of introducing functional groups on the surface of AC and adding redox-active molecules (K₃Fe(CN)₆) into 2?M KOH aqueous electrolytes. The surface-oxygen functionalized AC (FAC) was synthesized using HNO₃ echoed as the electrode and 2?M KOH with 0.1?M K₃Fe(CN)₆ as the electrolyte. The surface functional groups of the AC not only contribute to the pseudocapacitance but also increase the active sites of the electrode/electrolyte interface, which enhances the electrochemical activity of the Fe(CN)₆^3?/Fe(CN)₆^4? redox pair, thus leading to high capacitance. In the redox electrolyte, the specific capacitance was much higher in 229.17?F?g^?1 (1?A?g^?1) achieved for those FAC than in raw AC (only 147.06?F?g^?1). Similarly, the FAC electrode suggested high energy density and extended cycling stability in the KOH?+?K₃Fe(CN)₆ electrolyte.     

Electroanalytical Study of Methanol Oxidation and Oxygen Reduction at Carbon Nanohorns‐Pt Nanostructured Electrodes

This work reports a comprehensive electroanalytical study of carbon nanohorns (CNHs) in electrochemical applications. Compared to other types of carbons, the bare CNHs electrode exhibited higher peak current densities and lowest anodic peak‐to‐cathodic peak separation of less than 50 mV for the [Fe(CN)^4?]₆/[Fe(CN)^3?]₆ redox couple. Furthermore, CNHs exhibited excellent electrocatalyst supporting properties for porous Pt film towards methanol oxidation reaction reaching a peak current density of 127 mA cm^?2 or peak current mass activity 184 mA mg_Pt^?1. Regarding oxygen reduction reaction, an onset potential as positive as 0. 77 V vs. Ag/AgCl was achieved with CNHs/porous Pt film.     

The Effect of Ionic Liquid Covalent Bonding to Sol‐Gel Processed Film on Ion Accumulation and Transfer

Accumulation of electroactive anions into a silicate film with covalently bonded room temperature ionic liquid film deposited on an indium tin oxide electrode was studied and compared with an electrode modified with an unconfined room temperature ionic liquid. A thin film containing imidazolium cationic groups was obtained by sol‐gel processing of the ionic liquid precursor 1‐methyl‐3‐(3‐trimethoxysilylpropyl)imidazolium bis(trifluoromethylsulfonyl)imide together with tetramethylorthosilicate on the electrode surface. Profilometry shows that the obtained film is not smooth and its approximate thickness is above 1 μm. It is to some extent permeable for a neutral redox probe – 1,1′‐ferrocene dimethanol. However, it acts as a sponge for electroactive ions like Fe(CN)₆^3?, Fe(CN)₆^4? and IrCl₆^3?. This effect can be traced by cyclic voltammetry down to a concentration equal to 10^?7 mol dm^?3. Some accumulation of the redox active ions also occurs at the electrode modified with the ionic liquid precursor, but the voltammetric signal is significantly smaller compare with the bare electrode. The electrochemical oxidation of the redox liquid t‐butyloferrocene deposited on silicate confined ionic liquid film is followed by the expulsion of the electrogenerated cation into an aqueous solution. On the other hand, the voltammetry obtained with the electrode modified with t‐butyloferrocene solution in the ionic liquid precursor exhibits anion sensitive voltammetry. This is explained by anion insertion into the unconfined ionic liquid deposit following t‐butylferricinium cation formation.     

Electrochemical Characteristics of Poly(<Emphasis Type="Italic">o</Emphasis>-Aminobenzoic Acid) Modified Glassy-Carbon Electrode and Its Electrocatalytic Activity towards Oxidation of Epinephrine

Poly(o-aminobenzoic acid) (o-ABA) film is deposited on glassy-carbon electrode (GCE) by electropolymerization in pH 7.0 phosphate buffer solution (PBS). Electrochemical behavior of modified electrode is investigated by electrochemical impedance spectroscopy (EIS), different pulse voltammetry (DPV), and cyclic voltammetry (CV). The results indicate that there is a greater resistance during the electron transfer process in poly(o-ABA) film than in bare GCE for the redox of [Fe(CN)₆]³⁻/[Fe(CN)₆]⁴⁻. Further research indicates that epinephrine (EP) can be strongly absorbed on the surface of the poly(o-ABA) film-modified electrode. The modified electrode shows an excellent electrocatalytical activity on EP oxidation. The EP cathodic peak potential shifts negatively with a slope of −53.5 mV/pH, indicating that equal amounts of proton and electron are involved in the electrode reaction process. In pH 7.0 PBS, the peak current of EP and the concentration has a linear relationship from 0 to 65 μM by amperometric current-time curve. __________ From Elektrokhimiya, Vol. 41, No. 9, 2005, pp. 1059–1065. Original English Text Copyright ? 2005 by Cheng, Jin, Zhang. The text was submitted by the authors in English.     

Sorption of [Fe(CN)6]3− and [Fe(CN)6]4− ions on the surface of Fe(III), Cr(III), and Zr(IV) oxyhydroxide hydrogels from aqueous solutions

The sorption of [Fe(CN)₆]^3? and [Fe(CN)₆]^4? anions on the surface of Fe(III), Cr(III), and Zr(IV) oxyhydroxide hydrogels at various pH values of hydrogel precipitation from solutions without a support electrolyte and from NaCl and Na₂SO₄ solutions with an ionic strength of 0.5 was studied. It was found that isotherms of sorption of [Fe(CN)₆]^3? and [Fe(CN)₆]^4? anions from solutions without a support electrolyte and from NaCl solutions and those of sorption of [Fe(CN)₆]^4? from Na₂SO₄ solutions are described by the Langmuir equation. It was established that the sulfate background suppresses the sorption of [Fe(CN)₆]^3? on Fe(III) and Zr(IV) oxyhydroxides. Both anions are sorbed only when the surface of the oxyhydroxides is charged positively; the Langmuir equation parameters A _max and K tend to decrease to the point of zero charge as the pH value of oxyhydroxide precipitation increases. An electrostatic mechanism of the sorption of [Fe(CN)₆]^3? and [Fe(CN)₆]^4? anions was suggested.     

Enzyme-free impedimetric glucose sensor based on gold nanoparticles/polyaniline composite film

A non-enzymatic impedimetric glucose sensor was fabricated based on the adsorption of gold nanoparticles (GNPs) onto conductive polyaniline (PANI)-modified glassy carbon electrode (GCE). The modified electrode (GCE/PANI/GNPs) was characterized by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM). The determination of glucose concentration was based on the measurement of EIS with the mediation of electron transfer by ferricyanide ([Fe(CN)₆]^3?). The [Fe(CN)₆]^3? is reduced to ferrocyanide ([Fe(CN)₆]^4?), which in turn is oxidized at GCE/PANI/GNPs. An increase in the glucose concentration results in an increase in the diffusion current density of the [Fe(CN)₆]^4? oxidation, which corresponds to a decrease in the faradaic charge transfer resistance (R _ct). A wide linear concentration range from 0.3 to 10 mM with a lower detection limit of 0.1 mM for glucose was obtained. The proposed sensor shows high sensitivity, good reproducibility, and stability. In addition, the sensor exhibits no interference from common interfering substances such as ascorbic acid, acetaminophen, and uric acid.     

Electrochemical Determination of L‐Lactate Using Phenylboronic Acid Monolayer‐Modified Electrodes

The surface of a gold (Au) disk electrode was modified with a self‐assembled monomolecular layer of dithiobis(4‐butylamino‐m‐phenylboronic acid) (DTBA‐PBA) to prepare L ‐lactate‐sensitive electrodes. The DTBA‐PBA‐modified electrodes exhibited an attenuated cyclic voltammogram (CV) for the Fe(CN)₆^3? ion in the presence of L ‐lactate, as a result of the formation of phenylboronate ester of L ‐lactate accompanied with the addition of OH^? ion to the boron atom. In other words, the negatively charged DTBA‐PBA monolayer blocked the electrode surface from the access of the Fe(CN)₆^3?/4? ions. Thus, the DTBA‐PBA monolayer‐modified Au electrode can be used for determining L ‐lactate on the basis of the change in redox current of Fe(CN)₆^3?/4? ions. The calibration graph useful for determining 1–30 mM L ‐lactate was obtained.     

Potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate film-modified electrode

A potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate(III) (CHCF) film-modified glassy carbon electrode is proposed. The electroactive film is introduced onto the glassy carbon electrode surface by electrodeposition of cobalt, which forms a thin CHCF film on subsequent anodic scanning in KClHCl solution (pH 5.0–5.5) containing K₃Fe(CN)₆. The thickness of the film on the electrode surface can be controlled by changing the electrodeposition time and the concentrations of cobalt(II) and Fe(CN)^3?₆ ions. The modified electrode exhibits a linear response in the concentration range 1 × 10^?1 ?3 × 10^?5 M potassium ion activity, with a near-Nernstian slope (48–54 mV per decade) at 25 ± 1°C. The detection limit is 1 × 10^?5 M. The stability, response time and selectivity were investigated. The electrode exhibits good selectivity for potassium ion with the twelve cations investigated. The relative standard deviation is 1.5% (n=10). The effects of the thickness of the electroactive film and the pH of the solution on the electrode response were also investigated.     

Electrochemical Modification of Gold Electrodes with Azobenzene Derivatives by Diazonium Reduction

An electrochemical study of Au electrodes electrografted with azobenzene (AB), Fast Garnet GBC (GBC) and Fast Black K (FBK) diazonium compounds is presented. Electrochemical quartz crystal microbalance, ellipsometry and atomic force microscopy investigations reveal the formation of multilayer films. The elemental composition of the aryl layers is examined by X‐ray photoelectron spectroscopy. The electrochemical measurements reveal a quasi‐reversible voltammogram of the Fe(CN)₆^3?/4? redox couple on bare Au and a sigmoidal shape for the GBC‐ and FBK‐modified Au electrodes, thus demonstrating that electron transfer is blocked due to the surface modification. The electrografted AB layer results in strongest inhibition of the Fe(CN)₆^3?/4? response compared with other aryl layers. The same tendencies are observed for oxygen reduction; however, the blocking effect is not as strong as in the Fe(CN)₆^3?/4? redox system. The electrochemical impedance spectroscopy measurements allowed the calculation of low charge‐transfer rates to the Fe(CN)₆^3? probe for the GBC‐ and FBK‐modified Au electrodes in relation to bare Au. From these measurements it can be concluded that the FBK film is less compact or presents more pinholes than the electrografted GBC layer.     

The Effect of Adsorption of Ions of the Hexacyanoferrate(II)/(III) Redox Pair on Self-Assembly of Octanethiol at Its Adsorption from Aqueous Solutions on Gold Electrode

The effect of components of the redox pair K₃[Fe(CN)₆]/K₄[Fe(CN)₆] on the dynamics of formation of octanethiol (OT) monolayers from aqueous thiol-containing solutions of 0.1 М NaClO₄ is studied by cyclic voltammetry (CVA). The formation of OT monolayers is shown to depend on the presence of ions of hexacyanoferrate(II)/(III) in solution. Being added to solution, the components of the [Fe(CN)₆]^3–/4– redox pair sharply increase the time of formation of the insulating monolayer OT films and make them less stable. The destabilizing and inhibiting action of [Fe(CN)₆]^3–/4– ions becomes stronger as their concentration in solution increases. The adsorption activity of individual components of the redox pair is assessed. The strong and approximately equal adsorption activity of ions [Fe(CN)₆]^3– and [Fe(CN)₆]^4– on gold in the presence of octanethiol is observed. At the same time, OT and the hexacyanoferrate(II)/(III) ions can be placed in the following row: OT > [Fe(CN)6]^3– ≈ [Fe(CN)₆]^4–. Recommendations are given on how to eliminate the interfering action of the K₃[Fe(CN)₆]/K₄[Fe(CN)₆] redox-pair ions when studying the insulating properties of thiol monolayers on gold.     

A novel electrochemical sensor based on molecularly imprinted polymers for caffeine recognition and detection

A sensitive and selective electrochemical sensor based on molecularly imprinted polymers (MIPs) was developed for caffeine (CAF) recognition and detection. The sensor was constructed through the following steps: multiwalled carbon nanotubes and gold nanoparticles were first modified onto the glassy carbon electrode surface by potentiostatic deposition method successively. Subsequently, o-aminothiophenol (ATP) was assembled on the surface of the above electrode through Au–S bond before electropolymerization. During the assembled and electropolymerization processes, CAF was embedded into the poly(o-aminothiophenol) film through hydrogen bonding interaction between CAF and ATP, forming an MIP electrochemical sensor. The morphologies and properties of the sensor were characterized by scanning electron microscopy, cyclic voltammetry, and differential pulse voltammetry. The recognition and determination of the sensor were observed by measuring the changes of amperometric response of the oxidation-reduction probe, [Fe(CN)₆]^3?/[Fe(CN)₆]^4?, on modified electrode. The results demonstrated that the prepared sensor had excellent selectivity and high sensitivity for CAF, and the linear range was 5.0?×?10^?10?~?1.6?×?10^?7?mol?L^?1 with a detection limit of 9.0?×?10^?11?mol?L^?1 (S/N?=?3). The sensor was also successfully employed to detect CAF in tea samples.     

Simultaneous determination of catechol and hydroquinone by carbon paste electrode modified with hydrophobic ionic liquid-functionalized SBA-15

Hydrophobic ionic liquid-functionalized SBA-15 modified carbon paste electrode (CPSPE) was fabricated, and its electrochemical performance was investigated by cyclic voltammetry, electrochemical impedance spectra, and chronocoulometry in K₃Fe(CN)₆/K₄Fe(CN)₆ solution. Compared with carbon paste electrode (CPE) and SBA-15 modified carbon paste electrode (CSPE), the electron transfer ability was in the sequence as: CPSPE>CSPE>CPE. Meanwhile, the electrocatalytic activity of CPSPE to catechol and hydroquinone was evaluated by cyclic voltammetry, and then, the linear concentration ranges were obtained by the amperometric detection from 2.0?×?10^-5 to 3.2?×?10^-4 M for catechol and 5.0?×?10^-5 to 5.5?×?10^-4 M for hydroquinone, with the detection limits of 5.0?×?10^-7 and 6.0?×?10^-7 M, respectively. The advantages of both ionic liquids and heterogeneous supports made CPSPE exhibit high electrocatalytic activity towards the redox of catechol and hydroquinone by significantly improving their reversibility and enhancing their peak currents. In addition, the present method was applied to the determination of catechol and hydroquinone in artificial wastewater sample, and the results were satisfactory.     

The electrocrystallization of nickel on vitreous carbon A kinetic and structural study of nucleation and coalescence

FeOOH deposition films were formed on gold electrodes by polarization in an electrolyte containing Fe²⁺. The time dependence of the formation current suggests a diffusion-controlled formation process. The oxidation of Fe(CN)₆^4? at FeOOH films shows no Tafel-like behavior. It is assumed that the Fe²⁺ to form the film, as well as the Fe(CN)₆^4? to be oxidized, have to diffuse through an adherent, strongly hydrous layer of Fe(OH)₃ to the surface of FeOOH.     

Assessing the Apparent Effective Thickness of the Supported Hybrid Bilayer Membranes Consisting of Octadecanethiol and Phospholipid by ac Impedance Spectroscopy

The electrochemical behavior of the gold electrode modified by hybrid bilayer membranes in different concentrations of Fe(CN)₆^3?/Fe(CN)₆^4? was investigated by electrochemical impedance spectroscopy and cyclic voltammetry technology. The electron transfer between gold and the redox species separated by the hybrid bilayers assembly was completed by an electron tunneling process. A detailed equivalent circuit for electron transport across the HBMs is proposed. It was found that the apparent effective thickness of the hybrid bilayer membranes was lower than that of the sum of the chain length of octadecanethiol and phospholipid so some possible collapsed sites might exist at the hybrid bilayer membranes.     

Preparation of Carbon Nanotubes/Neutral Red Composite Film Modified Electrode and Its Catalysis on Rutin

Neutral red was directly electropolymerized onto the carbon nanotubes modified electrode. A polymerized neutral red/carbon nanotubes composite film was characterized by scanning electron micrograph (SEM) and cyclic voltammetry (CV). Well‐defined voltammetric responses are observed for [Fe(CN)₆]^4?/3? on the composite film modified glassy carbon electrode. And it's found that this modified electrode has good catalysis on the redox of rutin. Differential pulse voltammetry method was used to determinate the concentration of rutin and obtain a linear equation between the current and concentration in a certain range. The modified electrode is satisfied with us for its good sensibility and stability.