Simultaneous Determination of Adenosine and Adenosine‐5′‐triphosphate at Nanogold Modified Indium Tin Oxide Electrode by Osteryoung Square‐Wave Voltammetry

Simultaneous determination of adenosine and adenosine‐5′‐triphosphate has been described using nanogold modified indium tin oxide electrode. Gold nanoparticles catalyze adenosine oxidation which results in increasing separation of oxidation peaks of adenosine and ATP, making it possible to determine adenosine and adenosine‐5′‐triphosphate simultaneously. The detection limits for adenosine and ATP were found as 0.07 μM and 0.10 μM respectively with sensitivity 22.9 nA μM^?1 and 20.9 nA μM^?1. The proposed method was also used for sensing the compounds in biological samples. Influence of various square‐wave parameters and different pH conditions on peak current has also been reported.     

Electrochemical Behaviors of Adenosine‐5′‐triphosphate on Molecular Wire Modified Carbon Paste Electrode and Its Sensitive Detection

A new electrochemical method was proposed for the determination of adenosine‐5′‐triphosphate (ATP) based on the electrooxidation at a molecular wire (MW) modified carbon paste electrode (CPE), which was fabricated with diphenylacetylene (DPA) as the binder. A single well‐defined irreversible oxidation peak of ATP appeared on MW‐CPE with adsorption‐controlled process and enhanced electrochemical response in a pH 3.0 Britton‐Robinson buffer solution, which was due to the presence of high conductive DPA in the electrode. The electrochemical parameters of ATP were calculated with the electron transfer coefficient (α) as 0.54, the electron transfer number (n) as 1.9, the apparent heterogeneous electron transfer rate constant (k_s) as 2.67 × 10^?5 s^?1 and the surface coverage (Γ_T) as 4.15 × 10^?10 mol cm^?2. Under the selected conditions the oxidation peak current was proportional to ATP concentration in the range from 1.0 × 10^?7 mol L^?1 to 2.0 × 10^?3 mol L^?1 with the detection limit as 1.28 × 10^?8 mol L^?1 (3σ) by sensitive differential pulse voltammetry. The proposed method showed good selectivity without the interferences of coexisting substances and was successful applied to the ATP injection samples detection.     

Graphene Functionalized Graphite Electrode with Diphenylacetylene for Sensitive Electrochemical Determination of Adenosine‐5′‐triphosphate

In this paper a molecular wire modified carbon paste electrode (MW‐CPE) was firstly prepared by mixing graphite powder with diphenylacetylene (DPA). Then a graphene (GR) and chitosan (CTS) composite film was further modified on the surface of MW‐CPE to receive the graphene functionalized electrode (CTS‐GR/MW‐CPE), which was used for the sensitive electrochemical detection of adenosine‐5′‐triphosphate (ATP). The CTS‐GR/MW‐CPE exhibited excellent electrochemical performance and the electrochemical behavior of ATP on the CTS‐GR/MW‐CPE was carefully studied by cyclic voltammetry with an irreversible oxidation peak appearing at 1.369 V (vs. SCE). The electrochemical parameters such as charge transfer coefficient (α) and electrode reaction standard rate constant (k_s) were calculated with the results of 0.53 and 5.28×10^?6 s^?1, respectively. By using differential pulse voltammetry (DPV) as detection technique, the oxidation peak current showed good linear relationship with ATP concentration in the range from 1.0 nM to 700.0 µM with a detection limit of 0.342 nM (3σ). The common coexisting substances, such as uric acid, ascorbic acid and guanosine‐5′‐triphosphate (GTP), showed no interferences and the modified electrode was successfully applied to injection sample detection.     

Electrochemical Behaviours and Detection of Adenosine‐5¢‐triphosphate on an Ionic Liquid Modified Carbon Paste Electrode

In this paper a new electrochemical method based on the ionic liquid modified carbon paste electrode (IL‐CPE) was proposed for the determination of adenosine‐5′‐triphosphate (ATP) in a pH 4.5 Britton‐Robinson (B‐R) buffer solution. IL‐CPE was prepared by using 1‐butyl‐3‐methylimidazolium trifluoroacetate (BMIMCF₃COO) as the modifier. Cyclic voltammetry was used to investigate the electrochemical behaviors of ATP on the IL‐CPE, and the results indicated that IL‐CPE exhibited strong electrocatalytic ability to promote the oxidation of ATP with a single well‐defined irreversible adsorption‐controlled oxidation peak appeared. The electrochemical reaction parameters of ATP were calculated with the results of the electron transfer coefficient (α) as 0.40, the electron transfer number (n) as 1.17, the apparent heterogeneous electron transfer rate constant (ks) as 3.66 × 10^‐6 s^‐1 and the surface coverage (Γ_τ) as 2.48 × 10^‐9 mol cm^‐2. Under the selected conditions the proposed IL‐CPE showed good performances to the ATP detection in the concentration range from 0.1 to 1000.0 μmol L^‐1 with the detection limit as 3.65 × 10^‐8 mol L^‐1 (3σ) by differential pulse voltammetry. The method showed good selectivity to the ATP detection without the interferences of coexisting substances and was successfully applied to the ATP injection samples detection with satisfactory results.     

Enzymatic Synthesis of Nucleoside‐5′‐O‐(1‐thiophosphates) and (SP)‐Adenosine‐5′‐O‐(1‐thiotriphosphate)

Treatment of adenosine with PSCl₃ in trimethyl phosphate gave, after ion‐exchange chromatography, adenosine‐5′‐O‐monophosphate (AMP; 28%) and adenosine‐5′‐O‐monothiophosphate (AMPS; 48%). AMPS was studied as a thiophosphate residue donor in an enzymatic transphosphorylation with nucleoside phosphotransferase (NPase) of the whole cells of Erwinia herbicola. As exemplified by a number of natural and sugar‐ and base‐modified nucleosides, it was demonstrated that NPase of the whole cells of Erwinia herbicola catalyzes the transfer of both thiophosphate and phosphate residues with a similar efficiency. An incubation of AMPS in a phosphorylating extract of Saccharomyces cerevisiae (K‐phosphate buffer (0.3 M , pH 7.0); 3% glucose; 15 mM MgCl₂; 28°, 8 h), followed by ion‐exchange column chromatography afforded AMP (8%), AMPS (recovered, 23%), ATP (11%), and (S_P)‐adenosine‐5′‐O‐(1‐thiotriphosphate) ((S_P)‐ATPαS); (total yield 37%; 48% based on the consumed AMPS). For comparison of physicochemical properties, adenosine was chemically transformed into ATPαS as a mixture of the (S_P) (53%) and (R_P) (44%) diastereoisomers.     

Core–Shell Hollow Microspheres of Magnetic Iron Oxide@Amorphous Calcium Phosphate: Synthesis Using Adenosine 5′‐Triphosphate and Application in pH‐Responsive Drug Delivery

Drug nanocarriers with magnetic targeting and pH‐responsive drug‐release behavior are promising for applications in controlled drug delivery. Magnetic iron oxides show excellent magnetism, but their application in drug delivery is limited by low drug‐loading capacity and poor control over drug release. Herein, core–shell hollow microspheres of magnetic iron oxide@amorphous calcium phosphate (MIO@ACP) were prepared and investigated as magnetic, pH‐responsive drug nanocarriers. Hollow microspheres of magnetic iron oxide (HMIOs) were prepared by etching solid MIO microspheres in hydrochloric acid/ethanol solution. After loading a drug into the HMIOs, the drug‐loaded HMIOs were coated with a protective layer of ACP by using adenosine 5′‐triphosphate (ATP) disodium salt (Na₂ATP) as stabilizer, and drug‐loaded core–shell hollow microspheres of MIO@ACP (HMIOs/drug/ACP) were obtained. The as‐prepared HMIOs/drug/ACP drug‐delivery system exhibits superparamagnetism and pH‐responsive drug‐release behavior. In a medium with pH 7.4, drug release was slow, but it was significantly accelerated at pH 4.5 due to dissolution of the ACP shell. Docetaxel‐loaded core–shell hollow microspheres of MIO@ACP exhibited high anticancer activity.     

Ultra‐fast adenosine 5′‐triphosphate,adenosine 5′‐diphosphate and adenosine 5′‐monophosphate detection by pressure‐assisted capillary electrophoresis UV detection

Herein, we report a new CE method to measure adenine nucleotides adenosine 5′‐triphosphate, adenosine 5′‐diphosphate, and adenosine 5′‐monophosphate in red blood cells. For this purpose, 20 mmol/L sodium acetate buffer at pH 3.80 was used as running electrolyte, and the separation was performed by the simultaneous application of a CE voltage of 25 kV and an overimposed pressure of 0.2 psi from inlet to outlet. A rapid separation of these analytes in less than 1.5 min was obtained with a good reproducibility for intra‐ and inter‐assay (CV<4 and 8%, respectively) and an excellent analytical recovery (from 98.3 to 99%). The applicability of our method was proved by measuring adenine nucleotides in red blood cells.     

Potentiometric,NMR, and Fluorescence‐Emission Studies on the Binding of Adenosine 5′‐Triphosphate (ATP) by Open‐Chain Polyamine Receptors Containing Naphthylmethyl and/or Anthrylmethyl Groups

The interaction in aqueous solution of adenosine 5′‐triphosphate (ATP) with a series of open‐chain polyamines linked at one or both ends to anthrylmethyl or naphthylmethyl fragments was followed by potentiometric titration, ¹H‐, ¹³C‐, and ³¹P‐NMR spectroscopy, and by steady‐state fluorescence measurements. The results revealed greater stabilities for the compounds containing one anthracene moiety than for those with one naphthalene moiety, the stabilities of the compounds with both ends N‐substituted with naphthylmethyl groups being close to those containing just one anthrylmethyl unit. The ¹H‐NMR spectra showed that in all systems, there is involvement of π‐π stacking interactions in the stabilization of the adduct species. The competitive effect of the anions afforded by the supporting electrolyte was checked in some of the studied systems working at two different ionic strenghts (0.15M and 1.0M NaCl). The joint analysis of the spectrofluorimetric titrations and pH‐metric species‐distribution curves showed that for all the ATP? receptor systems, a quenching of the fluorescence occurred upon protonation of the adenine N(1)atom. Steady‐state fluorescence and time‐correlated single‐photon‐counting analysis of a system made up of ATP and a bis‐chromophoric polyamine receptor containing anthracene and naphthalene fluorophores established that the energy‐transfer process between the naphthalene and anthracene moieties is still operative despite the presence of ATP.     

Synthesis of 1‐amino‐2‐methylindoline by Raschig process: Kinetics of the oxidation of 1‐amino‐2‐methylindoline by chloramine

The synthesis of 1‐amino‐2‐methylindoline by the Raschig process was undertaken in aqueous solution. The principal side reaction that occurs in the medium is the oxidation of 1‐amino‐2‐methylindoline formed by chloramine. To increase the yield of 1‐amino‐2‐methylindoline, its oxidation by chloramine was studied by GC and HPLC at various concentrations of reactants and for a pH interval ranging between 9.9 and 13.5. The reaction is bimolecular and exhibits a specific acid catalysis. In alkaline medium, 1‐amino‐2‐methylindole is the principal product. The enthalpy and entropy of activation were determined at pH 12.89. In unbuffered solution, the interaction was autocatalyzed by the ammonium ions formed, which indicates a competitive oxidation of neutral and ionic forms of 1‐amino‐2‐methylindoline by chloramine. A mathematical treatment based on one implicit equation allows a quantitative interpretation of all the phenomena observed over the above pH interval. It takes both acid–base dissociation equilibrium and alkaline hydrolysis of chloramine into account. © 2002 Wiley Periodicals, Inc. Int J Chem Kinet 34: 515–523, 2002     

Voltammetric Behavior of Sodium 7-Methoxyl-4＇-hydroxylisoflavone-3＇-sulfonate and Its Application

Voltammetric behavior of sodium 7‐methoxyl‐4′‐hydroxylisoflavone‐3′‐sulfonate (SMHS) in the aqueous solution from pH 1 to 5 was studied by linear sweep voltammetry, cyclic voltammetry and normal pulse voltammetry. Experimental results showed that in 0.2 mol*L^?1 sodium citrate‐hydrochloric acid buffer solution (pH=4.65), SMHS caused only one reduction wave at ?1.34 V (vs. saturated calomel electrode, SCE), which was an h‐reversible adsorptive wave of SMHS protonized involving one electron and one proton. The peak current of SMHS on linear sweep voltammogram was proportional to its concentration in the range of 8.0 × 10 ?8.0·10 mol*L^?1 (r = 0.995). and the detection limit was 5.0·10^?‐⁶mol*L^?1. The method was applied to determination of SMHS, in synthetic samples. In addition, its scavenging effect on superoxide anion radical was studied by the auto‐oxidation of pyrogallol in HCI‐tris buffer solution (pH = 8.2) in order to explain its peculiar biological effects. The experimental results proved that SMHS has antioxidant quality, and it is an efficient free radical scavenger of superoxide anion radical.     

π‐Extended Dihydrophenazines with Three‐State NIR Electrochromism Involving Large Conformational Changes

π‐Extended dihydrophenazines were successfully prepared by oxidation of 2‐(N ‐arylamino)anthracenes. Their roof‐type conformations were revealed by X‐ray diffraction analysis, and the analysis of the optical properties indicated the presence of intramolecular charge‐transfer processes. Upon chemical oxidation, the electronic absorption dramatically changed in a two‐step fashion. The electron spin resonance (ESR) analysis revealed that, depending on the amount of oxidant added, either a paramagnetic radical cation or a diamagnetic dication was generated. The NMR analysis revealed a conformational change upon oxidation, which was supported by theoretical calculations. A three‐state electrochromic behavior was observed during the electrochemical oxidation and reduction cycles, showing sequential switching between visible and near‐infrared (NIR) absorption properties upon application of electrochemical stimuli.     

Nanomolar Determination of Methyldopa in the Presence of Large Amounts of Hydrochlorothiazide Using a Carbon Paste Electrode Modified with Graphene Oxide Nanosheets and 3‐(4′‐Amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic Acid

A novel electrochemical sensor for sensitive detection of methyldopa at physiological pH was developed by the bulk modification of carbon paste electrode (CPE) with graphene oxide nanosheets and 3‐(4′‐amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic acid (3,′AA). Applying square wave voltammetry (SWV), in phosphate buffer solution (PBS) of pH 7.0, the oxidation current increased linearly with two concentration intervals of methyldopa, one is 1.0×10^?8–1.0×10^?6 M and the other is 1.0×10^?6–4.5×10^?5 M. The detection limit (3σ) obtained by SWV was 9.0 nM. The modified electrode was successfully applied for simultaneous determination of methyldopa and hydrochlorothiazide. Finally, the proposed method was applied to the determination of methyldopa and hydrochlorothiazide in some real samples.     

Rapid and Selective Determination of Vanillin in the Presence of Caffeine,its Electrochemical Behavior on an Au Electrode Electropolymerized with 3‐Amino‐1,2,4‐triazole‐5‐thiol

Electrochemical oxidation of vanillin (VAN) in the presence of caffeine (CAF) was studied on a gold (Au) electrode modified with 3‐amino‐1,2,4‐triazole‐5‐thiol (ATT) film by using differential pulse voltammetry (DPV) and cyclic voltammetry (CV) method. The formation of the ATT film on the Au electrode surface was characterized by the CV, fourier transform infrared spectroscopy (FTIR) and impedance spectroscopy (EIS) methods. A single irreversible oxidation peak of the VAN was obtained by using the CV method. The determination of VAN in the presence of CAF was carried out at pH 4 in Britton Robinson buffer (BR) by the DPV method. Under the optimal conditions, the oxidation peak current was proportional to the concentration of VAN in the range of 1.1 μM to 76.4 μM in the presence of CAF with the correlation coefficient of 0.997 and the detection limit of 0.19 μM (S/N=3). The selective determination of VAN in a commercial coffee sample was carried out with satisfactory results on the ATT‐Au modified electrode.     

Fingerprinting DNA Oxidation Processes: IR Characterization of the 5‐Methyl‐2′‐Deoxycytidine Radical Cation

Methylated cytidine plays an important role as an epigenetic signal in gene regulation. Its oxidation products are assumed to be involved in active demethylation processes but also in damaging DNA. Here, we report the photochemical production of the 5‐methyl‐2′‐deoxycytidine radical cation via a two‐photon ionization process. The radical cation is detected by time‐resolved IR spectroscopy and identified by band assignment using density functional theory calculations. Two final oxidation products are characterized with liquid chromatography coupled to mass spectrometry.     

Dissociation behavior of poly(α‐hydroxy acrylic acid)

Dissociation behavior of poly(α‐hydroxy acrylic acid) (PHA) was investigated by potentiometric titration in the presence of NaCl and/or divalent metal chlorides. It was found that pH values of PHA aqueous solutions increased with time when the degree of dissociation, α, is high (α ≧ 0.5 for NaCl system) and decreased in the lower α region (α < 0.5 for NaCl). The increase of pH was attributed to lactone ring formation that occurs between a carboxyl group and a neighbor hydroxyl group upon protonation to the former, and the decrease of pH to an induction effect by lactone ring to −COOH group. The pH‐increasing process was analyzed by assuming it being of a first order to obtain a time constant. On the basis of time constant thus estimated and pKa values for divalent counterion systems, a correlation between counterion binding and lactone ring formation was discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1523–1531, 1999     

Aptamer-oligonucleotide binding studied by capillary electrophoresis: cation effect and separation efficiency

Novel features of DNA structure, recognition and discrimination have been recently elucidated through the solution structural characterization of DNA aptamers that bind cofactors, amino acids and peptides with high affinity and specificity. Multidimensional nuclear magnetic resonance methodologies have been successfully applied to solve the solution structures. In this work, it was demonstrated that capillary electrophoresis was a powerful tool allowing the fundamental study of the binding mechanism between a DNA aptamer and three ligands, adenosine and adenylate compounds, i.e., adenosine diphosphate (ADP) and adenosine triphosphate (ATP). In order to gain further insight into this binding, thermodynamic measurements under different values of parameters (such as salt nature and its concentration (x) in the run buffer) were carried out. The results showed that dehydration at the binding interface, van der Waals interactions, H-bonding and adjustment of the aptamer recognition surface were implied in the aptamer-ligand association. As well, it was demonstrated that the addition in the medium of the sodium monovalent cation Na(+) or the nickel divalent cation Ni(2+) decreased the complex formation. Separation efficiency and peak shape can also be improved by Mg(2+) divalent cation, which increased the mass transfer kinetics during the ligand-aptamer binding process. A significant separation for the worst separated pair of peaks on the electropherogram ((ADP, ATP) peak pair) was thus achieved.     

Carbon Paste Electrode Incorporating 1‐[4‐(Ferrocenyl Ethynyl) Phenyl]‐1‐Ethanone for Electrocatalytic and Voltammetric Determination of Tryptophan

A carbon paste electrode spiked with 1‐[4‐ferrocenyl ethynyl) phenyl]‐1‐ethanone (4FEPE) was constructed by incorporation of 4FEPE in graphite powder‐paraffin oil matrix. It has been shown by direct current cyclic voltammetry and double step chronoamperometry that this electrode can catalyze the oxidation of tryptophan (Trp) in aqueous buffered solution. It has been found that under optimum condition (pH 7.00), the oxidation of Trp at the surface of such an electrode occurs at a potential about 200 mV less positive than at an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and rate constant for the chemical reaction between Trp and redox sites in 4FEPE modified carbon paste electrode (4FEPEMCPE) were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of Trp showed a linear dependent on the Trp concentrations and linear calibration curves were obtained in the ranges of 6.00×10^?6 M–3.35×10^?3 M and 8.50×10^?7 M–6.34×10^?5 M of Trp concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 1.80×10^?6 M and 5.60×10^?7 M by CV and DPV methods. This method was also examined as a selective, simple and precise new method for voltammetric determination of tryptophan in real sample.     

Expression,Purification and Characterization of a Bifunctional α‐L‐Arabinofuranosidase/β‐D‐Xylosidase from Trichoderma Koningii G‐39

A gene of α‐L ‐arabinofuranosidase (Abf) from Trichoderma koningii G‐39 was successfully expressed in Pichia pastoris. The recombinant enzyme was purified to > 90% homogeneity by a cation‐exchanged chromatography. The purified enzyme exhibits both α‐L ‐arabinofuranosidase and β‐D ‐xylosidase (Xyl) activities with p‐nitrophenyl‐α‐L ‐arabionfuranoside (pNPAF) and 2,4‐dinitrophenyl‐β‐D ‐xylopyanoside (2,4‐DNPX) as substrate, respectively. The stability and the catalytic feature of the bifunctional enzyme were characterized. The enzyme was stable for at least 2 h at pH values between 2 and 8.3 at room temperature when assayed for Abf and Xyl activities. Enzyme activity decreased dramatically when the pH exceeded 9.5 or dropped below 1.5. The enzyme lost 35% of Abf activity after incubation at 55 °C for 2 h, but retained 95% of Xyl activity, with 2,4‐DNXP as substrate, under the same conditions. Further investigation of the active site topology of both enzymatic functions was performed with the inhibition study of enzyme activities. The results revealed that methyl‐α‐L ‐arabinofuranoside inhibition is noncompetitive towards 2,4‐DNPX as substrate but competitive towards pNPAF. Based on the thermal stability and the inhibition studies, we suggest that the enzymatic reactions of Abf and Xyl are performed at distinct catalytic sites. The recombinant enzyme possesses both the retaining transarabinofuranosyl and transxylopyranosyl activities, indicating both enzymatic reactions proceed through a two‐step, double displacement mechanism.     

Electroanalytical Characterization of Adenosine Mono-, Di- and Triphosphate Oxidation on Carbon Electrode

Abstract

Electrochemical oxidation of adenosine mononucleotides was characterized using a pencil graphite carbon electrode for the first time. All three adenosine mononucleotides, adenosine triphosphate (ATP), adenosine diphosphate (ADP), and adenosine monophosphate (AMP), showed irreversible electro-activity at the carbon electrode, yielding a well-defined oxidation current response. The peak potential was highly dependent on pH. The lowest mononucleotide concentration detected was 1 µM. The electro-analytical data presented here for the oxidation of adenosine mononucleotides provides the basis for further bioanalytical investigations related to DNA-drug interactions.     

Coordination Centres of Purine Nucleotides: Adenosine‐5′‐diphosphate and Adenosine‐5′‐triphosphate in their Reactions with Nickel(II), Cobalt(II) and Tetramines

Interactions between the nucleotides: adenosine‐5′‐diphosphate (ADP) and adenosine‐5′‐triphosphate (ATP) with Ni^II and Co^II ions, as well as with spermine (Spm) and 1,11‐diamine‐4,8‐diazaundecane (3,3,3‐tet) are the subject of this study. Composition and stability constants of mixed complexes thus formed have been determined on the basis of the potentiometric measurements, whereas interaction centres in ligands have been identified by VIS and NMR spectral parameter analysis. Mixed tetraprotonated complexes with Ni^II, i.e. Ni(ADP)H₄(Spm), Ni(ATP)H₄(Spm), Ni(ADP)H₄(3,3,3‐tet) and Ni(ATP)H₄(333‐tet), are identified as ML·······L′ type adducts, in which the main coordination centre is the nucleotide nitrogen N(1) or N(7) donor atom, and the fully protonated polyamine is engaged in noncovalent interactions with nucleotide phosphate group oxygen atoms. Ni(ADP)H₂(Spm), Ni(ATP)H₂(Spm), Ni(ADP)H₂(3,3,3‐tet) and Ni(ATP)H₂(3,3,3‐tet) complexes represent the {N3} coordination type In diprotonated mixed complexes of Ni^II with spermine are weak noncovalent interligand interactions, providing an additional stabilising effect. Formation of ML·······L′ type molecular complexes has been observed in systems with Co^II: Co(ADP)H₄(Spm), Co(ATP)H₄(Spm), Co(ADP)H₄(3,3,3‐tet) and Co(ATP)H₄(3,3,3‐tet), in which the N(7) atom and oxygen atoms of the phosphate group are involved in coordination and the fully protonated polyamine is engaged in noncovalent interactions with the nucleotide N(1).