溶出伏安法同时测定矿山地下水中痕量砷铅

本文以电化学预处理的金电极为工作电极,采用线性扫描溶出伏安法实现了矿山地下水中痕量As3+、Pb2+的同时测定。研究了金电极的预处理方法、不同预富集时间和不同电解质对重金属离子测定的影响规律。研究发现,电化学预处理有利于金电极对重金属离子的响应,在最优实验条件下,As3+、Pb2+在电化学活化的金电极上分别于0.18V、-0.07V产生灵敏的溶出峰,峰高与其浓度线性相关,检测限分别可达到0.5!g/L、2!g/L。该方法操作简单、干扰小、线性范围宽、灵敏度高。     

A Highly Sensitive Method for Determination of Monobutyltin in Aqueous Media by Stripping Voltammetry at a Renewable Silver Amalgam Annular Band Electrode

An adsorptive stripping voltammetric (AdSV) procedure for the determination of monobutyltin in aqueous media at a silver liquid amalgam film‐modified silver solid amalgam annular band electrode (AgLAF? AgSAE) is described. Determination of monobutyltin proceeds in two steps. At the beginning monobutyltin ions (BuSn³⁺) are accumulated from 0.1 M NH₄NO₃ and 10 % ethanol solution at a potential of ?0.2 V, than the BuSn⁰ film is preconcentrated at the working electrode surface at a potential of ?0.7 V. After this step the DP AdSV voltammogram is recorded. The analytical parameters and the procedure of the electrode regeneration and activation were optimized. The calibration curve of monobutyltin in the range 0.02–0.30 mg L^?1 is linear (r=0.9973). The detection limit for 5 s of preconcentration, calculated as 3σ of the blank was equal to 0.004 mg L^?1, repeatability of the peak current was 1.8 % (n=5). Repeatability and sensitivity of monobutyltin determination depends strongly on the analyzed solution properties, measurement conditions and the working electrode quality. The proposed procedure was tested by means of monobutyltin determination in tap waters.     

Determination of Folic Acid by Adsorptive Stripping Voltammetry at a Lead Film Electrode

An adsorptive stripping voltammetric procedure for the determination of folic acid at an in situ plated lead film electrode was described. Formation of lead film on a glassy carbon substrate and accumulation of folic acid was performed simultaneously from an acetate buffer solution of pH 5.6 at the potential ?0.88 V. The measurements were carried out from aerated solutions. The calibration graph for an accumulation time of 300 s was linear from 2×10^?9 to 5×10^?8 mol L^?1. The detection limit was 7×10^?10 mol L^?1, the relative standard deviation for 2×10^?8 mol L^?1 of folic acid was 3.9%. The proposed procedure was applied to folic acid determinations in pharmaceutical preparations.     

Determination of Lead and Cadmium at Silver Electrode by Subtractive Anodic Stripping Voltammetry in Plant Materials Containing Tl

Lead and cadmium have been determined by the subtractive anodic stripping voltammetry using the square‐wave mode at a silver electrode without removal of oxygen. The samples containing large amount of thallium were collected from a highly contaminated region. The presence of thallium strongly affects the peak shape of Cd. The plant material digestion was performed with HNO₃/HClO₄ mixture using pressurised microwave decomposition. The proposed method used for the lead determination was validated by the inter‐method comparison (ICP‐MS). The cadmium determination was validated using certified reference material. The results obtained, supported by statistical tests, demonstrated the usefulness of the method for the lead determination in samples containing large amounts of Cd and Tl. It is important to note that Cd can only be quantified when the thallium concentration is much lower than that of cadmium.     

Copper Sensing in Alkaline Electrolyte Using Anodic Stripping Voltammetry by Means of a Lead Mediator

Anodic stripping voltammetry (ASV) is an analysis technique that permits the selective and quantitative analysis of metal ion species in solution. It is most commonly applied in neutral to acidic electrolyte largely due to inherent metal ion solubility. Bismuth (Bi) is a common film used for ASV due to its good sensitivity, overall stability and insensitivity to O₂. ASV, utilizing a Bi film, along with cadmium (Cd) and lead (Pb) as the plating mediators, has recently been adapted to determine zinc (Zn) concentrations in highly alkaline environments (30 % NaOH or 35 % M KOH). Successful analysis of Zn in alkaline relies on the ability of the hydroxide to form soluble metal anion species, such as Bi(OH)₄⁻ and Zn(OH)₄²⁻. Here, we look to extend this technique to detect and quantify copper (Cu) ions in these highly basic electrolytes. However, in general, the use of ASV to detect and quantify Cu ion concentrations is notoriously difficult as the Cu stripping peak potential overlays with that of Bi from the common Bi film electrode. Here, an ASV method for determining Cu concentration in alkaline solutions is developed utilizing Pb as a deposition mediator. As such, it was found that when analyzing Cu solutions in the presence of Pb, the stripping voltammetry curves present separate and defined Cu stripping peaks. Different analyzes were made to find the best stripping voltammetry performance conditions. As such, an accumulation time of 5 minutes, an accumulation potential of≤−1.45 V vs. Hg/HgO, and a concentration of 35 wt% KOH were determined to be the conditions that presented the best ASV results. Utilizing these conditions, calibration curves in the presence of 5.0 ppm Pb showed the best linear stripping signal correlation with an r‐squared value of 0.991 and a limit of detection (LOD) of 0.67 ppm. These results give way to evaluating Cu concentrations using ASV in aqueous alkaline solutions.     

Study of Bare and Mercury‐Coated Vibrated Carbon,Gold and Silver Microwire Electrodes for the Determination of Lead and Cadmium in Seawater by Anodic Stripping Voltammetry

Carbon, gold and silver microwires are revisited under vibrated conditions for detection of trace lead and cadmium in seawater. The Pb and Cd peaks fully overlapped on the bare gold and carbon electrodes and partially on the silver electrode. The sensitivity of all three was insufficient for detection in uncontaminated waters. Peak separation was obtained after coating with mercury (Hg). Only the Hg‐coated silver electrode is suitable when preplated. Limits of detection for Pb using the Hg/C and Hg/Ag electrodes (20–40 pM), and Cd (70 pM), are sufficiently low for Pb and Cd detection in seawater.     

Iridium Oxide Film Electrodes for Anodic Stripping Voltammetry

The new iridium oxide film electrode, applied for the determination of lead(II), cadmium(II) and copper(II) traces using differential pulse anodic stripping voltammetry (DP ASV) is presented. The electrode display an interesting stripping voltammetric performance which compares with electrodes commonly used in voltammetry. The deposited film is known as anodically electrodeposited iridium oxide film (AEIROF). The AEIROF electrode is characterized by long‐term stability (more than 40 days) and very good reproducibility of the analytical signals in this time (≤12% for 0.5 μM of lead). The regeneration of iridium film is very simple in a time shorter than 60 seconds. The effects of various factors such as: thickness of AEIROF film, preconcentration potential and time, supporting electrolyte composition, potential interferences are optimized. The detection limit for AEIROF film electrode based on glassy carbon for an accumulation time of 30 s is as low as 7 nM for lead(II). The repeatability of the method at a concentration level of the lead(II) as low as 0.5 μM, expressed as RSD is 2.5% (n=10). The proposed method was successfully applied and validated by studying certified reference material CTA‐OTL‐1. Such an attractive use of ‘mercury–free’ ‐ environmentally friendly electrodes offers great promise to measure trace metals.     

Characteristics of Subtractive Anodic Stripping Voltammetry of Lead,Cadmium and Thallium at Silver‐Gold Alloy Electrodes

Silver‐gold alloy electrodes have been studied for the purpose of the quantitative determination of heavy metals by subtractive anodic stripping voltammetry, (SASV). The results have been compared with those obtained with the silver and gold electrodes. The 50/50 a/o Ag/Au alloy electrode is the most suitable for quantifying thallium in the presence of lead and cadmium. The separation of its peak from those of lead and cadmium is 200 mV, which is about twice the separation obtained on the pure metal electrodes and is also better than on mercury. The silver electrode is suitable for the simultaneous determination of thallium, lead and cadmium. The peaks of lead and cadmium overlap on the 50/50 alloy. Pure silver or pure gold can be used for simultaneous quantification of these two metals. The use of gold for quantifying lead and cadmium is more limited because the peak potential of cadmium is shifted in the negative direction as its concentration increases and at [Cd²⁺]>200 nM, the two peaks merge. SASV enables correction for background currents and is of utmost importance for obtaining well‐defined peaks. The peaks of lead, cadmium and thallium appear over a relatively narrow potential range (ca. 200 mV) on all the electrodes presented in this work. For this reason, the quantifying of a peak is based on the derivative at the inflection point of only one of its branches (ascending or descending). All SASV measurements were carried out without removal of oxygen.     

Coulometric Anodic Stripping Voltammetry of Lead at Copper Column Electrode

A flow coulometric electroanalytical system using a copper column electrode with a copper wire inserted into a Nafion tube was developed to determine Pb(II) content based on anodic stripping voltammetry. The electrolysis efficiency of 5 μM Pb(II) was evaluated to be 100.4±4.5 % (n=5) when the length of the copper wire and flow rate of the Pb(II) solution were 50 cm and 0.1 mL min⁻¹, respectively. The amount of electricity due to the re-oxidation of Pb electrodeposited at the copper column electrode was proportional to the concentration of Pb(II) in the range between 0.1 to 100 μM, and the limit of detection for Pb(II) was 0.8 μM for a deposition time of 15 min. Interference from the presence of Cd(II) could be avoided and the selective determination of Pb(II) was successfully achieved by adjustment of the electrodeposition potential.     

Renewable Copper and Silver Amalgam Film Electrodes of Prolonged Application for the Determination of Elemental Sulfur Using Stripping Voltammetry

New, renewable copper (Hg(Cu)FE) and silver (Hg(Ag)FE) based amalgam film electrodes applied for the determination of elemental sulfur using differential pulse cathodic stripping voltammetry are presented. With surface areas adjustable from 1 to 12 mm², both electrodes are characterized by very good surface reproducibility (≤2%) and long‐term stability (a few thousand measurement cycles). The mechanical refreshing of the amalgam film takes about 1–2 seconds. The effects of various factors such as instrumental parameters and the supporting electrolyte composition were optimized. Interferences from sulfides are easily removed by the addition of acid, and bubbling with argon, for Hg(Ag)FE. In the case of Hg(Cu)FE, sulfides did not interfere. The calibration graph is linear within the studied range from 16 ng L^?1 to 4.8 μg L^?1 for Hg(Cu)FE, and up to 6.4 μg L^?1 for Hg(Ag)FE (t_acc=15 s). The correlation coefficients for the two electrodes were at least 0.997. The detection limits for a low concentration of S(0) and t_acc=60 s are as low as 14 ng L^?1 for Hg(Cu)FE and 4 ng L^?1 for Hg(Ag)FE. The proposed method was successfully applied and validated by studying the recovery of S(0) from spiked river water.     

TiC Working Electrode. Voltammetric Characteristics and Application for Determination of Lead Traces by Stripping Voltammetry

The TiC working electrode was tested as a novel, potential electrode for anodic stripping voltammetric determination of lead(II) ions traces. To demonstrate the practical applicability of the TiC electrode, an underpotential deposition/dissolution (UPD) phenomena system in electrolyte without removal of oxygen was tested. The electrode was constructed be means of mounting a TiC disk (Ø=3.5 mm) in a resin body. Three compositions of TiC were tested differing in stoichiometry, namely TiC_0.6, TiC_0.8, and TiC_1.0. The key problem is the method of electrochemical activation of the TiC electrode. No or improperly activated electrode is not polarized and is unsuitable as a voltammetric sensor. The TiC electrode was used for the determination of Pb²⁺ in concentrations ranging from 1 to 100 nM. The instrumental parameters, composition of supporting electrolyte and procedures of the electrode activation were optimized. The repeatability of DP ASV runs in synthetic solutions covering the entire concentration range is better than 3%. The calibration curve is characterized by a correlation coefficient of at least 0.999. The detection limit was 2 nM for an electrodeposition time of 30 s. The method enables determination of Pb²⁺ in the presence of, among the others, high excesses of Cd, Cu, In, Sb, Se, and Tl ions as well as surfactants, Triton X‐100 and humic acids. The analysis of Pb²⁺ in synthetic solutions with and without surfactants, certified reference material and natural water samples have been performed. The voltammetric data were associated with the structural characterization of the electrode surface using scanning electron microscopy (SEM) and X‐ray fluorescence spectroscopy (XRF).     

Determination of Lead and Cadmium by Stripping Voltammetry After Separation from Humic Acid by Thin-Layer Chromatography

Abstract

Interferences resulting from the presence of humic acid (HA) and other surface-active substances in a sample matrix decrease the reliability of Pb and Cd determinations obtained by square-wave anodic stripping voltammetry (SWASV). The implementation of thin-layer chromatography (TLC) prior to SWASV minimizes the effect of these interferents by physically separating Pb and Cd from the sample matrix prior to analysis. The determination of both Pb and Cd was shown to be feasible after TLC separation from laboratory standards spiked with 100 ppm humic acid and from a lake water sample spiked with 1 ppm of Pb and Cd.     

银微盘电极上碘离子的示差脉冲溶出伏安法

基于Ｉ能与Ａｇ生成难溶出化合物特性，在银微盘电极上研究了Ｉ的示差脉冲溶出伏安法（ＤＰＳＶ）。该法不需镀汞，不要搅拌，可在较稀稀的支持电解质溶液中实施。于０．０８ｍｏｌ／ＬＨＡｃ－ＮａＣ及０．０１ｍｏｌ／ＬＥＤＴＡ介质中，能检出１．００×１０＾－８ｍｏｌ／Ｌ的Ｉ，Ｉ的浓度为５．００×１０＾－６－－１．２０×１０＾－８ｍｏｌ／Ｌ范围与峰电流有良好的线性关系。该法用于自来水中Ｉ的测定，相对偏差为４．３％     

Silver Amalgam Film Electrode of Prolonged Application in Stripping Chronopotentiometry

The utility of the cylindrical silver‐based mercury film electrode of prolonged analytical application in stripping chronopotentiometry (SCP) was examined. This electrode allowed us to obtain good reproducibility of results owing to the special electrode design, which enables regeneration of the thin layer before each measurement cycle. The accessible potential window in KNO₃ (pH 2), acetate and ammonia buffers was defined, and the optimal conditions (i.e., stripping current, deposition potential and deposition time) for the determination of Cd and Pb traces were selected. The detection limits, obtained for an accumulation time of 60 s, were 0.023 μg/L for Cd and 0.075 μg/L for Pb. The response increases linearly with Cd, Pb and Zn concentration, up to at least 100 μg/L. It was also shown that the proposed procedure ensures excellent separation of the In and Tl, Pb and Tl or the In and Cd signals. The method was tested with dolomite and lake sediment samples, and good agreement with reference values was achieved. The obtained results showed good reproducibility (RSD=5–6%) and reliability.     

脉冲溶出伏安法中汞膜碳纤维电极性能的研究

采用脉冲阳极溶出伏安法,研究了汞膜碳纤维电极测定痕量金属离子的行为,并与汞膜玻碳电极和悬汞电极进行了系统的对比,显示了碳纤维电极在静止态溶液、极稀溶液、有机溶液和双电极体系中具有特殊的优越性。本文对该电极的制作,预处理和实际测试条件进行了探讨。     

Adsorptive Stripping Determination of Scandium(III) with Mordant Blue 9 on Silver Amalgam Film Electrode

A new adsorptive stripping voltammetric method for the determination of trace scandium(III) based on the adsorption of scandium(III)‐mordant blue 9 complex on the cyclic renewable mercury film silver based electrode (Hg(Ag)FE) is presented. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimized. The calibration graph is linear from 2 nM (0.09 μg L^?1) to 90 nM (4 μg L^?1) for a preconcentration time of 45 s, with correlation coefficient of 0.9995. For a Hg(Ag)FE with a surface area of 7.9 mm² the detection limit for a preconcentration time of 90 s is as low as 5 ng L^?1. The repeatability of the method at a concentration level of the analyte as low as 0.2 μg L^?1, expressed as RSD is 1.9 % (n=5). The proposed method was successfully applied and validated by studying the certified reference material (CRM 320 – river sediment) and natural samples with simultaneous recovery of Sc(III) from spiked water and sediment samples.     

Underpotential Deposition and Stripping of Lead at Disorganized Monolayer‐Modified Gold Electrodes

Underpotential deposition (UPD) and stripping of Pb²⁺ at thiol‐based disorganized monolayer‐modified gold electrodes was studied by cyclic voltammetry (CV) and electrochemical quartz crystal microgravimetry (EQCM). Electrodes modified with mercaptoacetic acid or mercaptoethane sulfonic acid were studied. Due to the proximity of the potentials for the Pb UPD and thiol reductive desorption, achievement of a UPD‐stripping voltammetry methodology for determination of low concentrations of Pb²⁺ was not successful. However by comparison of the CV and EQCM data and consideration of the possible mass changes per mole electrons transferred in light of the other species present in solution, possible mechanisms are put forward for the deposition and stripping of Pb²⁺ at thiol‐modified electrodes.     

Critical Comparison of Four Simple Adaptors for Flow Amperometric and Stripping Voltammetry with Mercury Drop Electrodes in Batch Cells

Electrochemical batch cells with mercury drop electrodes, MDEs, are readily available from a number of producers and widely used in electroanalysis for polarography, voltammetry and stripping voltammetry. To increase sample throughput and reduce reagent and sample consumption, the tendency is to couple the MDE with flow analysis systems (e.g., FIA, SIA or BIA). Many special flow cells for MDEs are described in the literature, but it is easier to convert existing commercial batch cells to flow operation. To assess the performance of such flow adaptors, four models were chosen because they are directly fitted to the glass capillary of any MDE, light enough not to impair the mechanical drop knocker and can be effortlessly built in the laboratory. They were all found adequate for flow amperometry and stripping voltammetry, with differences in sensitivity, flow rate dependence, response time, drop stability, tolerance to bubbles, uncompensated resistance and recontamination of disposed analyte from the electrolytic bath. Two of them, a simple L‐shaped PTFE tube and an upstream nozzle holder made from a disposable pipette tip, gather a larger set of desirable features.