Anodic Stripping Voltammetric Determination of Lead in Tap Water at an Ordered Mesoporous Carbon/Nafion Composite film Electrode

A sensitive mercury‐free lead (Pb²⁺) sensor has been proposed based on an ordered mesoporous carbon and Nafion composite film (OMC/Nafion) coated glassy carbon electrode. The analysis of Pb²⁺ using anodic stripping voltammetry (ASV) includes two steps. Pb²⁺ ions are firstly reduced and deposited on the electrode surface in a Pb²⁺ solution (10 mL) during a preconcentration step biased at ?1.0 V, followed by a measurement step by differential pulse voltammetry (DPV) within the potential range of ?0.8 to ?0.3 V (scan rate: 20 mV/s, frequency: 20 Hz, amplitude: 50 mV, pulse width: 50 ms). Linear calibration curve was found to be from 20 nM to 2 μM for Pb²⁺ with a sensitivity of 17.4±1.38 μA/μM after a 5‐min of preconcentration. The detection limit was estimated to be around 4.60±0.12 nM at the signal to noise ratio of 3. Reproducibility (RSD%) was found to be 3.0% for a single sensor with eight measurements and 4.3% for five sensors prepared with identical procedures. The practical application of the proposed lead sensor was verified by determination of trace level of Pb²⁺ in tap water sample.     

Determination of Lead and Cadmium at Silver Electrode by Subtractive Anodic Stripping Voltammetry in Plant Materials Containing Tl

Lead and cadmium have been determined by the subtractive anodic stripping voltammetry using the square‐wave mode at a silver electrode without removal of oxygen. The samples containing large amount of thallium were collected from a highly contaminated region. The presence of thallium strongly affects the peak shape of Cd. The plant material digestion was performed with HNO₃/HClO₄ mixture using pressurised microwave decomposition. The proposed method used for the lead determination was validated by the inter‐method comparison (ICP‐MS). The cadmium determination was validated using certified reference material. The results obtained, supported by statistical tests, demonstrated the usefulness of the method for the lead determination in samples containing large amounts of Cd and Tl. It is important to note that Cd can only be quantified when the thallium concentration is much lower than that of cadmium.     

Simultaneous Determination of Pb and Cd Traces in Water Samples by Anodic Stripping Voltammetry Using a Modified GC Electrode

The determination of Pb and Cd with a Nafion‐modified glassy carbon electrode and Cu‐DPABA complex (Cu‐DPABA–NA/GCE; DPABA is methyl 3,5‐bis{bis‐[(pyridin‐2‐yl)methyl]amino}methyl‐benzoate) as an alternative electrode for anodic stripping voltammetry was described. Pb and Cd were accumulated in acetate buffer pH 4 at a potential of ?1.4 V (vs. Ag/AgCl electrode) for 120 s followed by a DPASV scan from ?1.2 to ?0.2 V. Under optimum conditions the calibration curves were linear in the range of 4.8×10^?9–5.0×10^?5 and 5.0×10^?9–5×10^?5 mol L^?1 for Pb and Cd, respectively. Detection limits were 1.8×10^?9 and 1.2×10^?9 mol L^?1 for Pb and Cd, respectively. Different parameters and conditions, such as membrane ingredients, accumulation time, potential and pH value were optimized. A study of interfering substances was also performed. A significant increase in current was achieved at the modified electrode in comparison with the bare glassy carbon electrode. The validation of the proposed method was made by Pb and Cd determination in the certified reference material Groundwater CRM 610 (BCR, Community Bureau of Reference, Brussels, Belgium). The electrode was successfully applied for determination of Pb and Cd in river water with a high content of organic contaminants without any pretreatment.     

Determination of Lead and Cadmium in Sea‐ and Freshwater by Anodic Stripping Voltammetry with a Vibrating Bismuth Electrode

A solid, bismuth (Bi), disk, electrode is used to determine lead (Pb) in natural waters including seawater. The diffusion layer thickness was lowered from 93 to 29 µm by stirring, and to 18 µm by using the vibrated version of the Bi electrode. The Bi electrode does not require removal of dissolved oxygen, which facilitates in situ detection. The electrode was tested for the determination of Pb in coastal seawater samples. The detection limit for Pb was 0.15 nM in acetate buffer and 0.5 nM in seawater using a 2 min deposition time. Cadmium can be determined together with Pb but the sensitivity is about 10×lower. The Bi electrode compares unfavourably to a mercury electrode in terms of sensitivity.     

Lead Determination by Anodic Stripping Voltammetry Using a p‐Phenylenediamine Modified Carbon Paste Electrode

Carbon paste electrodes were modified by mixing appropriate amounts of the monomers o‐phenylendiamine, p‐phenylendiamine and m‐phenylendiamine (o‐PD, p‐PD and m‐PD) into a graphite powder‐paraffin oil matrix. The electropolymerization of the incorporated phenylendiamine was then carried out in a carbon paste electrode in acidic medium by cyclic voltammetry between ?0.30 V and +0.90 or under constant potential. The modified carbon paste electrodes (MCPEs) obtained by this electropolymerization method were found to be useful for trace determination of Pb²⁺ in aqueous solutions. Lead(II) was first preconcentrated on the modified electrodes by complexation with the modifier, and the electrode was then transferred to an electrochemical cell. The best results in terms of sensitivity and detection limit were obtained with poly p‐phenylenediamine (poly (p‐PD)). For a 10‐min preconcentration time, the calibration plot was linear from 5×10^?8 mol L^?1 to 10^?5 mol L^?1, with r²=0.999 and relative standard deviation equal to 5%. However, the lowest lead concentration that could be detected was 10^?9 mol L^?1. Interference from metal ions like Cd(II), Hg(II), Zn(II), Fe(II) and Cu(II) was also studied.     

Coulometric Anodic Stripping Voltammetry of Lead at Copper Column Electrode

A flow coulometric electroanalytical system using a copper column electrode with a copper wire inserted into a Nafion tube was developed to determine Pb(II) content based on anodic stripping voltammetry. The electrolysis efficiency of 5 μM Pb(II) was evaluated to be 100.4±4.5 % (n=5) when the length of the copper wire and flow rate of the Pb(II) solution were 50 cm and 0.1 mL min⁻¹, respectively. The amount of electricity due to the re-oxidation of Pb electrodeposited at the copper column electrode was proportional to the concentration of Pb(II) in the range between 0.1 to 100 μM, and the limit of detection for Pb(II) was 0.8 μM for a deposition time of 15 min. Interference from the presence of Cd(II) could be avoided and the selective determination of Pb(II) was successfully achieved by adjustment of the electrodeposition potential.     

溶出伏安法同时测定矿山地下水中痕量砷铅

本文以电化学预处理的金电极为工作电极,采用线性扫描溶出伏安法实现了矿山地下水中痕量As3+、Pb2+的同时测定。研究了金电极的预处理方法、不同预富集时间和不同电解质对重金属离子测定的影响规律。研究发现,电化学预处理有利于金电极对重金属离子的响应,在最优实验条件下,As3+、Pb2+在电化学活化的金电极上分别于0.18V、-0.07V产生灵敏的溶出峰,峰高与其浓度线性相关,检测限分别可达到0.5!g/L、2!g/L。该方法操作简单、干扰小、线性范围宽、灵敏度高。     

Anodic Stripping Voltammetric Determination of Lead(II) with a 2‐Aminopyridinated‐Silica Modified Carbon Paste Electrode

Abstract

A carbon paste electrode modified with organically functionalized silica was used for the determination of lead. The measurements were carried out in three steps including an open circuit accumulation followed by electrolysis of accumulated lead at the carbon paste electrode and differential pulse voltammetric determination. The effects of several experimental variables such as carbon paste composition, pH and concentration of supporting electrolyte, electrolysis potential, and electrolysis time were studied. The resulting electrode demonstrates linear response over a wide range of Pb(II) concentration (5–1000 ng mL^?1) with an accumulation time of 60 sec. The effects of potential interfering ions were studied, and it was found that the proposed procedure is free from most interferences. Long lifetime and rapid and convenient renewal of electrode surface allows the use of a single modified electrode surface in multiple analytical determinations over at least 4 months. The prepared electrode was used for determination of lead spiked in a hair sample, and very good recovery results were obtained over a wide concentration range of lead.     

Carbon Paste Electrode Modified by Surfactant for Anodic Stripping Voltammetric Determination of Sulphadiazine

ＣａｒｂｏｎＰａｓｔｅＥｌｅｃｔｒｏｄｅＭｏｄｉｆｉｅｄｂｙＳｕｒｆａｃｔａｎｔｆｏｒＡｎｏｄｉｃＳｔｒｉｐｐｉｎｇＶｏｌｔａｍｍｅｔｒｉｃＤｅｔｅｒｍｉｎａｔｉｏｎｏｆＳｕｌｐｈａｄｉａｚｉｎｅＺｈａｎｇＺｈｅｎｇ－ｑｉ；ＣｈｅｎＺｈａｎ－ｇｕａｎ...     

碳纤维束汞膜电极二次微分阳极溶出伏安法测定锌中微量铅

本文提出了碳纤维束汞膜电极二次微分阳极溶出伏安法测定锌中微量铅的方法，对溶解氧，扫描速度，电极清洗时间，富集电位和时间及酸度的影响作了讨论。方法的线性范围为１．９－８０μｇ／Ｌ；检测下限达到１．９μｇ／Ｌ；对国家保证参考物质锌样中铅的测定，相对标准偏差和相对误差分别为２．６％和０．６５％，结果令人满意。     

预镀铋膜阳极溶出伏安法测定废水中微量铅和镉

本文采用预镀铋膜法修饰玻碳电极,并用该电极对废水中微量铅和镉同时进行了阳极溶出伏安法测定,研究了预镀铋膜测定铅和镉的条件。实验结果表明:铅和镉在铋膜电极上可得到灵敏的电位溶出峰,峰高和溶出电位与汞膜电极法相近,使用预镀铋膜电极可避免使用汞电极带来的环境污染。     

斜削碳纤维束复合微电极研制及ASV法测定人发中微量铅

本文叙述了斜削碳纤维束复合微电极制作方法及其伏安特性。用阳极溶出伏安法测定人发中的铅含量，确定了适宜的实验条件。方法简便、快速、灵敏度高、重现性好。检出限为０．１ｎｇ·ｍＬ－１，线性范围为１．０～２０ｎｇ·ｍＬ－１，相对标准偏差为３．４％。     

Simultaneous Determination of Trace Zinc(II) and Cadmium(II) by Differential Pulse Anodic Stripping Voltammetry Using a MWCNTs–NaDBS Modified Stannum Film Electrode

A multiwalled carbon nanotubes–sodium dodecyl benzene sulfonate (MWCNTs–NaDBS) modified stannum film electrode was employed for the determination of cadmium(II) and zinc(II). The Sn/MWCNTs‐NaDBS film electrode was prepared by applying MWCNTs–NaDBS suspension to the surface of the GCE, while the Sn film was plated in situ simultaneously with the target metal ions. Under optimal conditions, linear calibration curves were obtained in a range of 5.0 ?100.0 μg L^?1 with detection limits of 0.9 μg L^?1 for zinc(II) and 0.8 μg L^?1 for cadmium(II), respectively. This film electrode was successfully applied to the determination of Zn(II) and Cd(II) in tap water sample.     

Determination of Cadmium by Differential Pulse Adsorptive Stripping Voltammetry in the Present of Captopril

A new method is presented for determination of cadmium based on cathodic adsorptive stripping of the complex of cadmium with captopril,1‐[(2S)‐3‐mercapto‐2‐methylpropionyl]‐L ‐praline (CPL) at a hanging mercury drop electrode(HMDE). The most suitable operating conditions and parameters, such as pH, deposition potential, deposition time, ligand concentration, and others were selected and the determination of cadmium from aqueous solutions using the standard additions method was possible. Under the optimum conditions and for an accumulation time of 60 s, the measured peak current is proportional to the concentration of cadmium over the range of 1–300 nM. The limit of detection at S/N ratio of 3 was 0.3 nM and a relative standard deviation of 2.5% at 0.1 μM was achieved. The interference of other cations and anions was studied. The method was designed in order to determination of Cd in four analytical grade salts, with satisfactory results.     

同时测定癌症病人血液中锌镉铅铜的微分脉冲阳极溶出伏安法

用微分脉冲阳极溶出伏安法同时测定癌症病人血液中的锌、镉、铅和铜，以为癌症与这4种微量元素在血液中含量的相关性研究提供实验数据；癌症病人血液用硝酸-高氯酸消化，消化后的白色固体加水溶解，以0．100mol/L硫酸铵为底液，在三电极体系中进行测定，以峰电位定性，峰电流定量；用该法测定了3种癌症病人血液中的锌、镉、铅和铜，相对标准偏差为2．9％—3．3％(n＝6)，加标回收率为98％—110％；该法不用除氧、干扰少、分辨率好、准确度高，适用于临床血液中锌、镉、铅和铜的测定和研究。     

Study of Bare and Mercury‐Coated Vibrated Carbon,Gold and Silver Microwire Electrodes for the Determination of Lead and Cadmium in Seawater by Anodic Stripping Voltammetry

Carbon, gold and silver microwires are revisited under vibrated conditions for detection of trace lead and cadmium in seawater. The Pb and Cd peaks fully overlapped on the bare gold and carbon electrodes and partially on the silver electrode. The sensitivity of all three was insufficient for detection in uncontaminated waters. Peak separation was obtained after coating with mercury (Hg). Only the Hg‐coated silver electrode is suitable when preplated. Limits of detection for Pb using the Hg/C and Hg/Ag electrodes (20–40 pM), and Cd (70 pM), are sufficiently low for Pb and Cd detection in seawater.     

槲皮素化学修饰碳糊电极吸附溶出伏安法测定痕量铅

建立了用槲皮素修饰碳糊电极测定痕量铅的新方法 ,在 0 .1 0mol L甲酸盐缓冲液 (pH 4.3 )中 ,于 -0 .1 0V(vs.SCE)搅拌富集 ,再在 -0 .70V静止还原 40s后 ,阳极化扫描 ,于 -0 .42V左右获得一灵敏的铅阳极溶出峰。在最佳条件下 ,富集不同时间 ,其二次导数峰电流与Pb2 + 在 1 .0× 1 0 - 8～ 8.0× 1 0 - 7mol L和 2 .0× 1 0 - 9～ 6.0× 1 0 - 8mol L两个范围内呈线性关系 ,检出限为 8.0× 1 0 - 1 0 mol L(S N =3 )。同时初步探讨了电极反应机理。     

Determination of Lead and Cadmium by Stripping Voltammetry After Separation from Humic Acid by Thin-Layer Chromatography

Abstract

Interferences resulting from the presence of humic acid (HA) and other surface-active substances in a sample matrix decrease the reliability of Pb and Cd determinations obtained by square-wave anodic stripping voltammetry (SWASV). The implementation of thin-layer chromatography (TLC) prior to SWASV minimizes the effect of these interferents by physically separating Pb and Cd from the sample matrix prior to analysis. The determination of both Pb and Cd was shown to be feasible after TLC separation from laboratory standards spiked with 100 ppm humic acid and from a lake water sample spiked with 1 ppm of Pb and Cd.     

电化学法修饰玻璃碳电极及其铜的阳极溶出伏安法测定

在邻苯二酚－甲醛－ＮａＯＨ介质中，于－０．１￣＋１．５Ｖ（ｖｓ，ＳＣＥ）扫描范围内用循环伏安法制作修饰玻璃碳电极。电极可用于水中痕量铜的测定，其灵敏度比未修饰的玻璃碳电极提高３５倍以上，定量下限为０．１ｎｇ／ｍｌ。     

Facile and Simultaneous Stripping Determination of Zinc,Cadmium and Lead on Disposable Multiwalled Carbon Nanotubes Modified Screen‐Printed Electrode

Screen‐printed electrodes (SPEs) are cheap and disposable. But their application for heavy metal detection is limited due to the low sensitivity and poor selectivity. Here we report the ultrasensitive and simultaneous determination of Zn²⁺, Cd²⁺ and Pb²⁺ on a multiwalled carbon nanotubes and Nafion composite modified SPE with in situ plated bismuth film (MWCNTs/NA/Bi/SPE). The linear curves range from 0.5–100 µg L^?1 for Zn²⁺ and 0.5–80 µg L^?1 for Cd²⁺. Uniquely, the linear curve for Pb²⁺ ranges from 0.05–100 µg L^?1 with a detection limit of 0.01 µg L^?1. The practical application was verified in real samples with satisfactory results.