Electrochemical Detection of Melamine

Poly(caffeic acid) polymer was immobilized onto the surface of a glassy carbon electrode via electropolymerization. Voltammetry shows a signal related to the two‐electron oxidation of the immobilized hydroquinone groups in the caffeic acid monomer units. The modified electrode in aqueous solution shows complexation of the electrogenerated o‐quinone species with melamine thus allowing in the electrochemical detection of melamine by recording the shift in potential of the oxidation signal of the polymer. Melamine detection was investigated in pure aqueous solutions and in the presence of milk powder solutions and the proposed analytical method of melamine detection in milk powder was applied successfully with an average recovery of ca. (91±7.9)%.     

Glucose Biosensor Based on Multi‐Walled Carbon Nanotube Modified Glassy Carbon Electrode

An amperometric glucose biosensor based on multi‐walled carbon nanotube (MWCNT) modified glassy carbon electrode has been developed. MWCNT‐modified glassy carbon electrode was obtained by casting the electrode surface with multi‐walled carbon nanotube materials. Glucose oxidase was co‐immobilized on the MWCNT‐modified glassy carbon surface by electrochemical deposition of poly(o‐phenylenediamine) film. Enhanced catalytic electroreduction behavior of oxygen at MWCNT‐modified electrode surface was observed at a potential of ?0.40 V (vs. Ag|AgCl) in neutral medium. The steady‐state amperometric response to glucose was determined at a selected potential of ?0.30 V by means of the reduction of dissolved oxygen consumed by the enzymatic reaction. Common interferents such as ascorbic acid, 4‐acetamidophenol, and uric acid did not interfere in the glucose determination. The linear range for glucose determination extended to 2.0 mM and the detection limit was estimated to be about 0.03 mM.     

Electrochemical Behavior of Caffeic Acid Assayed with Gold Nanoparticles/Graphene Nanosheets Modified Glassy Carbon Electrode

A gold nanoparticle (AuNP) and graphene nanosheet (GN) modified glassy carbon electrode (GCE) is proposed as voltammetric sensor for caffeic acid assay. The sensor exhibits a surface‐confined and reversible process for oxidation of caffeic acid revealed by cyclic voltammetry. The results show more favorable electron transfer kinetics than the bare GCE. The linear response of the sensor is from 5×10^?7 to 5×10^?5 M with a detection limit of 5×10^?8 M (S/N=3). The AuNP/GN nanocomposite shows more favorable electrochemical activity and should be a kind of more robust and advanced functional material, which provides a promising platform for electrochemical sensors and biosensors. The method was successfully applied to detect caffeic acid in pharmaceutical tablets with satisfactory results.     

Determination of Caffeic Acid in Red Wine by Voltammetric Method

The electrochemical oxidation of 3,4‐dihydroxycinnamic acid, caffeic acid, leads to a stable electroactive poly(caffeic acid) thin film containing quinone moiety on a preactivated glassy polymeric carbon electrode. The properties of the deposited films as well as the stability study under different experimental conditions were investigated. Taking advantage of the electrochemical behavior, an analytical method based on differential pulse voltammetry for determination of caffeic acid in red wine was proposed.     

Electrochemical Detection of NADH,Cysteine, or Glutathione Using a Caffeic Acid Modified Glassy Carbon Electrode

A modified electrode was prepared using electrodeposition methods to immobilize caffeic acid (CAF) onto the surface of a glassy carbon electrode (GCE) to create a polymer suitable for biosensor development. The polymer film coverage of the surface bound species was further optimized using electrodeposition methods, thus increasing the surface coverage to ca. 10^?9 mol cm^?2. Using cyclic voltammetry, the modified carbon electrode was used to facilitate and observe the electrocatalytic oxidation of coenzymes such as NADH, cysteine, and glutathione at different concentrations. A calibration curve was determined in each case within the concentration range; 300 nM to 10 mM, with the limits of detection (LOD) of 246 µM, 99 µM, 2.2 µM for NADH, cysteine, and glutathione respectively.     

Electroanalysis of Caffeic Acid in Red Wine and Investigation of Thermodynamic Parameters Using an Ag Nanoparticles Modified Poly(Thiophene) Film Glassy Carbon Electrode

A silver nanoparticle decorated poly(thiophene) modified glassy carbon electrode (GCE) was prepared for determination of caffeic acid. The Ag/PTh/GCE surface was characterized by scanning electron microscopy (SEM) and energy‐dispersive X‐ray (EDX) spectroscopy. The modified electrode has shown higher electrocatalytic activity towards the oxidation of caffeic acid. The peak current of was found linear in the concentration range from 1.00×10^?8 to 4.83×10^?6 M with a detection limit of 5.3×10^?9 M (S/N=3). The modified electrode was used for determination of CA concentration in red wine samples. The thermodynamic constants, entropy change (ΔS), enthalpy change (ΔH) and Gibbs free energy change (ΔG) were calculated as ?166.34 J/(mol K), ?154.24 kJ/mol and ?104.75 kJ/mol at 25 °C, respectively.     

Gold Electrode Modified with Self‐Assembled Monolayer of Cysteamine‐Functionalized MWCNT and Its Application in Simultaneous Determination of Dopamine and Uric Acid

The voltammetric behavior of dopamine (DA) and uric acid (UA) on a gold electrode modified with self‐assembled monolayer (SAM) of cysteamine (CA) conjugated with functionalized multiwalled carbon nanotubes (MWCNTs) was investigated. The film modifier of functionalized SAM was characterized by means of scanning electron microscopy (SEM) and also, electrochemical impedance spectroscopy (EIS) using para‐hydroquinone (PHQ) as a redox probe. For the binary mixture of DA and UA, the voltammetric signals of these two compounds can be well separated from each other, allowing simultaneous determination of DA and UA. The effect of various experimental parameters on the voltammetric responses of DA and UA was investigated. The detection limit in differential pulse voltammetric determinations was obtained as 0.02 µM and 0.1 µM for DA and UA, respectively. The prepared modified electrode indicated a stable behavior and the presence of surface COOH groups of the functionalized MWCNT avoided the passivation of the electrode surface during the electrode processes. The proposed method was successfully applied for the determination of DA and UA in urine samples with satisfactory results. The response of the gold electrode modified with MWCNT‐functionalized SAM method toward DA, UA, and ascorbic acid (AA) oxidation was compared with the response of the modified electrode prepared by the direct casting of MWCNT.     

Electorchemical Studies of Cytochrome c on Electodes Modified by Single—Wall Carbon Naotubes

Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins.     

Fabrication of Glucose Biosensor Based on Encapsulation of Glucose‐Oxidase on Sol‐Gel Composite at the Surface of Glassy Carbon Electrode Modified with Carbon Nanotubes and Celestine Blue

A simple procedure was developed to prepare a glassy carbon electrode modified with multi walled carbon nanotubes (MWCNTs) and Celestin blue. Cyclic voltammograms of the modified electrode show stable and a well defined redox couple with surface confined characteristic at wide pH range (2–12). The formal potential of redox couple (E′) shifts linearly toward the negative direction with increasing solution pH. The surface coverage of Celestine blue immobilized on CNTs glassy carbon electrode was approximately 1.95×10^?10 mol cm^?2. The charge transfer coefficient (α) and heterogeneous electron transfer rate constants (k_s) for GC/MWCNTs/Celestine blue were 0.43 and 1.26 s^?1, respectively. The modified electrode show strong catalytic effect for reduction of hydrogen peroxide and oxygen at reduced overpotential. The glucose biosensor was fabricated by covering a thin film of sol‐gel composite containing glucose oxides (GOx) on the surface of Celestine blue /MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 0.3 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. The accuracy of the biosensor for glucose detection was evaluated by detection of glucose in a serum sample, using standard addition protocol. In addition biosensor can reach 90% of steady currents in about 3.0 sec and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) was eliminated. Furthermore, the apparent Michaelis–Menten constant 2.4 mM, of GOx on the nano composite exhibits excellent bioelectrocatalytic activity of immobilized enzyme toward glucose oxidation. Excellent electrochemical reversibility of redox couple, high stability, technically simple and possibility of preparation at short period of time are of great advantages of this procedure for modification of glucose biosensor.     

Electrodeposition of dendritic gold/silver nanaoparticles on disposable screen‐printed carbon electrode and its application of 4‐mercaptopyridine in in situ electrochemical surface‐enhanced Raman scattering

Column electrodes pretreated through oxidation–reduction cycles were traditionally used in electrochemical surface‐enhanced Raman scattering (SERS). In this study, a disposable screen‐printed carbon electrode was introduced into in situ electrochemical SERS through the electrodeposition of dendritic gold/silver nanoparticles (Au/AgNPs) onto the surface of the carbon working electrode to induce the SERS enhancement effect on the electrode. Scanning electron microscopy images showed that dendritic Au/AgNPs nanostructures could be fabricated under appropriate electrodeposition conditions and could present a minimum SERS factor of 4.25 × 10⁵. Furthermore, the absorbed behavior of 4‐mercaptopyridine was investigated under different potentials. The adsorption configuration was inferred to transform from ‘vertical’ to ‘lying‐flat’. The proposed new electrode combined with a portable Raman spectrometer could be useful in the identifying products or intermediates during electrochemical synthesis or electrochemical catalysis in in situ electrochemical SERS. Copyright © 2016 John Wiley & Sons, Ltd.     

A Microbial Sensor Based on Direct Electron Transfer at Shewanella Sp. Drop‐Coated Screen‐Printed Carbon Electrodes

Aerobically grown Shewanella sp. bacterial suspension drop‐coated on a disposable screen‐printed carbon electrode was found to possess electroactivity without the aid of redox mediator. Cyclic voltammetric studies revealed the characteristics of a mixed diffusion adsorption‐controlled electrochemical process for direct electron transfer at the bacteria‐modified electrode. Both FE‐SEM and ATR FT‐IR experiments were carried out to investigate the surface characteristics. The electroanalytical applicability was further demonstrated for electrocatalytic reduction of arsenite, hydrogen peroxide and nitrite. Low cost and very simple manufacturing procedure allow for the proposed bacterial sensor to be applied as disposable devices.     

Electrochemical Biosensing Platforms Using Phthalocyanine‐Functionalized Carbon Nanotube Electrode

Iron‐phthalocyanines (FePc) are functionalized at multi‐walled carbon nanotubes (MWNTs) to remarkably improve the sensitivity toward hydrogen peroxide. We constructed a highly sensitive and selective glucose sensor on FePc‐MWNTs electrode based on the immobilization of glucose oxidase (GOD) on poly‐o‐aminophenol (POAP)‐electropolymerized electrode surface. SEM images indicate that GOD enzymes trapped in POAP film tend to deposit primarily on the curved tips and evenly disperse along the sidewalls. The resulting GOD^@POAP/FePc‐MWNTs biosensor exhibits excellent performance for glucose with a rapid response (less than 8 s), a wide linear range (up to 4.0×10^?3 M), low detection limits (2.0×10^?7 M with a signal‐to‐noise of 3), a highly reproducible response (RSD of 2.6%), and long‐term stability (120 days). Such characteristics may be attributed to the catalytic activity of FePc and carbon nanotube, permselectivity of POAP film, as well as the large surface area of carbon nanotube materials.     

Direct Electrochemistry of Hemoglobin on Single‐Walled Carbon Nanotubes Modified Carbon Ionic Liquid Electrode and Its Electrocatalysis

In this article we report on the fabrication of a carbon ionic liquid electrode (CILE) by using a room temperature ionic liquid of 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) as binder. It was further modified by single‐walled carbon nanotubes (SWCNTs) to get a SWCNTs modified CILE denoted as SWCNTs/CILE. The redox protein of hemoglobin (Hb) was further immobilized on the surface of SWCNTs/CILE with the help of Nafion film. UV‐vis and FT‐IR spectra indicated that the immobilized Hb retained its native conformation in the composite film. The direct electrochemistry of Hb on the SWCNTs/CILE was carefully studied in pH 7.0 phosphate buffer solution (PBS). Cyclic voltammetric results indicated that a pair of well‐defined and quasireversible voltammetric peaks of Hb heme Fe(III)/Fe(II) was obtained with the formal potential (E°') at ?0.306 V (vs. SCE). The electrochemical parameters such as the electron transfer coefficient (α), the electron transfer number (n) and the apparent heterogeneous electron transfer rate constant (k_s) were calculated as 0.34, 0.989 and 0.538 s^?1, respectively. The fabricated Hb modified electrode showed good electrocatalytic ability to the reduction of trichloroacetic acid (TCA) in the concentration range from 20.0 to 150.0 mmol/L with the detection limit of 10.0 mmol/L (3σ).     

Functionalization of Multi Carbon Nanotubes with 1,2‐Naphthoquinone‐4‐sulfonic Acid Sodium: A Novel Sulphydryl Compounds Sensor Based on Functionalized Carbon Nanotube Film Using Michael Addition

The functionalized multi‐wall carbon nanotube with 1,2‐naphthoquinone‐4‐sulfonic acid sodium (Nq‐MWNT) was fabricated by a simple and low‐cost method. Techniques of scanning electron microscope (SEM) with energy dispersive X‐ray (EDX) analysis, fourier transform infrared spectroscopy (FT‐IR), ultraviolet visible spectroscopy (UV‐vis) and cyclic voltammetry (CV) were used to characterize the property of the Nq‐MWNT. The results showed that the MWNT with high functionalization of Nq can be obtained using this simple method. The Nq‐MWNT modified carbon paste electrode (Nq‐MWNT/CPE) was fabricated by drop‐casting technique. The resulted modified electrode was tested successfully to detection D‐penicillamine (D‐PA) and captopril (CAP) in an aqueous solution. It is found that D‐PA and CAP participate in Michael addition reaction with Nq on MWNT to form the corresponding thioquinone derivative. The reoxidation of adducts at a potential of less positive than D‐PA and CAP at the surface of the bare CPE leads to an increase in the oxidative current, which is proportional to the concentration of D‐PA and CAP. The catalytic response showed a wide linear range (3‐200 μM and 1‐130 μM for D‐PA and CAP, respectively) as well as its experimental limit of detection can be achieved 0.8 μM, and 0.4 μM for D‐PA and CAP, respectively. The modified electrode for D‐PA and CAP determination is of the property of simple preparation, good stability and high sensitivity. Furthermore, the fabricated electrode was used to determine the content of D‐PA and CAP in the tablet, suggesting the good accuracy of the method.     

Carbon Nanotubes‐Based Amperometric Cholesterol Biosensor Fabricated Through Layer‐by‐Layer Technique

A carbon nanotubes‐based amperometric cholesterol biosensor has been fabricated through layer‐by‐layer (LBL) deposition of a cationic polyelectrolyte (PDDA, poly(diallyldimethylammonium chloride)) and cholesterol oxidase (ChOx) on multi‐walled carbon nanotubes (MWNTs)‐modified gold electrode, followed by electrochemical generation of a nonconducting poly(o‐phenylenediamine) (PPD) film as the protective coating. Electrochemical impedance measurements have shown that PDDA/ChOx multilayer film could be formed uniformly on MWNTs‐modified gold electrode. Due to the strong electrocatalytic properties of MWNTs toward H₂O₂ and the low permeability of PPD film for electroacitve species, such as ascorbic acid, uric acid and acetaminophen, the biosensor has shown high sensitivity and good anti‐interferent ability in the detection of cholesterol. The effect of the pH value of the detection solution on the response of the biosensor was also investigated. A linear range up to 6.0 mM has been observed for the biosensor with a detection limit of 0.2 mM. The apparent Michaelis‐Menten constant and the maximum response current density were calculated to be 7.17 mM and 7.32 μA cm^?2, respectively.     

Electrocatalytic Oxidation and Voltammetric Determination of L‐Cysteic Acid at the Surface of p‐Bromanil Modified Carbon Paste Electrode

The electrochemical properties of L ‐cysteic acid studied at the surface of p‐bromanil (tetrabromo‐p‐benzoquinone) modified carbon paste electrode (BMCPE) in aqueous media by cyclic voltammetry (CV) and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00) in cyclic voltammetry, the oxidation of L ‐cysteic acid at the surface of BMCPE occurs at a half‐wave potential of p‐bromanil redox system (e.g., 100 mV vs. Ag|AgCl|KCl_sat), whereas, L ‐cysteic acid was electroinactive in the testing potential ranges at the surface of bare carbon paste electrode. The apparent diffusion coefficient of spiked p‐bromanil in paraffin oil was also determined by using the Cottrell equation. The electrocatalytic oxidation peak current of L ‐cysteic acid exhibits a linear dependency to its concentration in the ranges of 8.00×10^?6 M–6.00×10^?3 M and 5.2×10^?7 M–1.0×10^?5 M using CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (2σ) were determined as 5.00×10^?6 M and 4.00×10^?7 M by CV and DPV methods. This method was used as a new, selective, rapid, simple, precise and suitable voltammetric method for determination of L ‐cysteic acid in serum of patient's blood with migraine disease.     

Electrocatalytic Oxidation of Acyclovir on Poly(p‐Aminobenzene Sulfonic Acid) Film Modified Glassy Carbon Electrode

Acyclovir is an antiviral effective drug active compound. A glassy carbon electrode (GCE) was modified with an electropolymerized film of p‐aminobenzene sulfonic acid (p‐ABSA) in phosphate buffer solution (PBS). The polymer film‐modified electrode was used to electrochemically detect acyclovir. Polymer film showed excellent electrocatalytic activity for the oxidation of acyclovir. The anodic peak potential value of the acyclovir at the poly(p‐ABSA) modified glassy carbon electrode was 950 mV obtained by DPV. A linear calibration curve for DPV analysis was constructed in the acyclovir concentration range 2×10^?7–9×10^?6 mol L^?1. Limit of detection (LOD) and limit of quantification (LOQ) were obtained as 5.57×10^?8 and 1.85×10^?7 mol L^?1 respectively. The proposed method exhibits good recovery and reproducibility.     

Electrocatalytic Detection of Uric Acid on Nitrogen‐Doped Graphene Modified Electrode and Its Application

Nitrogen‐doped graphene (NG) was used to modify a glassy carbon electrode (GCE), which was applied to the voltammetric detection of uric acid (UA). Because of the presence of NG on the GCE surface, the modified electrode showed excellent electrocatalytic ability for UA oxidation with increase of the peak current and decrease of the peak potential. Compared to that of the traditional GCE, the overpotential of the oxidation peak decreased by 50 mV. Electrochemical performance of UA was studied on NG/GCE in detail, which showed a quasi‐reversible, diffusional‐controlled process. Electrochemical parameters including the charge transfer coefficient (α ), the number of electron transfer (n ), and the diffusional coefficient (D ) were calculated. At the optimal conditions, the oxidation peak current was linear, with UA concentration from 0.1 to 10.0 μmol/L as revealed by differential pulse voltammetry, and the detection limit was estimated as 0.042 μmol/L (3σ). The UA content in the urine sample of a healthy volunteer was determined by the proposed method with a recovery of 98.7–102.3%.     

Electrochemically Stimulated Insulin Release from a Modified Graphene‐functionalized Carbon Fiber Electrode

A graphene‐functionalized carbon fiber electrode was modified with adsorbed polyethylenimine to introduce amino functionalities and then with trigonelline and 4‐carboxyphenylboronic acid covalently bound to the amino groups. The trigonelline species containing quarterized pyridine groups produced positive charge on the electrode surface regardless of the pH value, while the phenylboronic acid species were neutral below pH 8 and negatively charged above pH 9 (note that their pK_a=8.4). The total charge on the monolayer‐modified electrode was positive at the neutral pH and negative at pH > 9. Note that 4‐carboxyphenylboronic acid was attached to the electrode surface in molar excess to trigonelline, thus allowing the negative charge to dominate on the electrode surface at basic pH. Negatively charged fluorescent dye‐labeled insulin (insulin‐FITC) was loaded on the modified electrode surface at pH 7.0 due to its electrostatic attraction to the positively charged interface. The local pH in close vicinity to the electrode surface was increased to ca. 9–10 due to consumption of H⁺ ions upon electrochemical reduction of oxygen proceeding at the potential of −1.0 V (vs. Ag/AgCl) applied on the modified electrode. The process resulted in recharging of the electrode surface to the negative value due to the formation of the negative charge on the phenylboronic acid groups, thus resulting in the electrostatic repulsion of insulin‐FITC and stimulating its release from the electrode surface. The insulin release was characterized by fluorescence spectroscopy (using the FITC‐labeled insulin), by electrochemical measurements on an iridium oxide, IrO_x, electrode and by mass spectrometry. The graphene‐functionalized carbon fiber electrode demonstrated significant advantages in the signal‐stimulated insulin release comparing with the carbon fiber electrode without the graphene species.     

中性红掺杂SiO2纳米粒子修饰的酶阵列传感器同时测定葡萄糖、乳酸和L-谷氨酸的研究

本文以中性红为核，二氧化硅为壳，利用反相微乳液技术，通过正硅酸四乙酯的水解制备了掺杂有中性红的二氧化硅纳米粒子，并用TEM技术进行了表征。核中性红能够催化测定葡萄糖，乳酸和L-谷氨酸的反应，而壳二氧化硅不仅克服了电活性物质中性红易流失的缺点，且具有高的生物亲和性。分别与葡萄糖氧化酶、乳酸氧化酶以及L-谷氨酸氧化酶混合后，修饰在碳阵列电极表面。最后在该酶阵列电极表面滴加一层Nafion, 防止电活性物质抗坏血酸、尿酸等的干扰。该酶阵列传感器与流动注射分析技术(FIA)相结合，可应用于同时检测大鼠血样中的葡萄糖，乳酸和L-谷氨酸浓度。该方法无需通过传统的色谱柱的分离，大大简化了实验条件，为这一领域的研究提供了有效的分析方法。